| Age | Commit message (Collapse) | Author |
|---|
|
commit 3685f19e07802ec4207b52465c408f185b66490e upstream.
Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9c5320f8d7d9a2cf623e65d50e1113f34d9b9eb1 upstream.
Fix the initialisation of older Quatech serial cards which are fitted with
the AMCC PCI Matchmaker interface chip.
Signed-off-by: Jonathan Woithe (jwoithe@just42.net)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 48c0247d7b7bf58abb85a39021099529df365c4d upstream.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f2d9b991c549f159dc9ae81f77d8206c790cbfee upstream.
Commit 35773dac5f862cb1c82ea151eba3e2f6de51ec3e "usb: xhci: Link TRB
must not occur within a USB payload burst" attempted to fix an issue
found with USB ethernet adapters, and inadvertently broke USB storage
devices. The patch attempts to ensure that transfers never span a
segment, and rejects transfers that have more than 63 entries (or
possibly less, if some entries cross 64KB boundaries).
usb-storage limits the maximum transfer size to 120K, and we had assumed
the block layer would pass a scatter-gather list of 4K entries,
resulting in no more than 31 sglist entries:
http://marc.info/?l=linux-usb&m=138498190419312&w=2
That assumption was wrong, since we've seen the driver reject a write
that was 218 sectors long (of probably 512 bytes each):
Jan 1 07:04:49 jidanni5 kernel: [ 559.624704] xhci_hcd 0000:00:14.0: Too many fragments 79, max 63
...
Jan 1 07:04:58 jidanni5 kernel: [ 568.622583] Write(10): 2a 00 00 06 85 0e 00 00 da 00
Limit the number of scatter-gather entries to half a ring segment. That
should be margin enough in case some entries cross 64KB boundaries.
Increase the number of TRBs per segment from 64 to 256, which should
result in ring segments fitting on a 4K page.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes: 35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst')
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d6c9ea9069af684358efedcaf2f2f687f51c58ee upstream.
Currently prepare_ring() returns -ENOMEM if the urb won't fit into a
single ring segment. usb_sg_wait() treats this error as a temporary
condition and will keep retrying until something else goes wrong.
The number of retries should be limited in usb_sg_wait(), but also
prepare_ring() should not return an error code that suggests it might
be worth retrying. Change it to -EINVAL.
Reported-by: jidanni@jidanni.org
References: http://bugs.debian.org/733907
Fixes: 35773dac5f86 ('usb: xhci: Link TRB must not occur within a USB payload burst')
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d303b1b5fbb688282bbf72a534b9dfed7af9fe4f upstream.
Add new PCI ID to support new model "Kaveri" family.
Signed-off-by: Philip Pokorny <ppokorny@penguincomputing.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1588c51cf6d782e63a8719681d905ef0ac22ee62 upstream.
There was a copy/paste error when reading the nwe_pulse value.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0645b93f6c223b594c0dca348e2ae0a23bccf6e3 upstream.
pinctrl-names property was missing from mmc nodes.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8bc661bfc0c2d221e209f4205bdaaf574d50100c upstream.
The uart timer will schedule a tasklet when it fires. It is possible that it
can fire inside _shutdown before it is killed in the dma and pdc cleanup
routines. This causes a tasklet that exists after the port is shutdown, so when
the kernel finally executes it, it panics as the tty port is NULL.
This is a somewhat rare condition but its possible if a program keeps on
opening/closing the port. It has been observed in particular with systemd
boot messages that were causing a kernel panic because of this behavior.
Moving the timer deletion to the beginning of the function stops a tasklet from
being scheduled unexpectedly.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
[nicolas.ferre@atmel.com: modify commit message, call setup_timer() in any case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bb7e73c598fb226c75f7625088a8f6a45a0fc892 upstream.
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f50c995f9ebf064cea1368bf361c4e29679415b4 upstream.
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0cc7c6c7916b1b6f34350ff1473b80b9f7e459c0 upstream.
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66ae460b13c31a176b41550259683c841a62af3e upstream.
When reset is caused by hbm protocol mismatch or timeout
we might end up in an endless reset loop and hbm protocol
will never sync
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9acec059c0cef0bf086c738f4c0b1f4447782a48 upstream.
value uLowNextTBTT yields wrong value.
ULL is needed with qwTSF
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
bScanning
commit 8f248dae133668bfb8e9379b4b3f0571c858b24a upstream.
byBBPreEDIndex value is initially 0, this means that from
cold BBvUpdatePreEDThreshold is never set.
This means that sensitivity may be in an ambiguous state,
failing to scan any wireless points or at least distant ones.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3a21f00a5002b14e4aab52aef59d33ed28468a13 upstream.
The latest version of NetworkManager does not recognize the device as wireless
without this change.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3c92a0bf4d72737035a16c4fe357ccd439c9b7d2 upstream.
When a system runs out of memory and the function
ptlrpc_register_bulk() is called from ptl_send_rpc() the call to
LNetMEAttach() fails due to failure to allocate memory. This forces
the code into an error path, which most probably previously went
untested. The error path:
if (rc != 0) {
CERROR("%s: LNetMEAttach failed x"LPU64"/%d: rc = %dn",
desc->bd_export->exp_obd->obd_name, xid,
posted_md, rc);
break;
}
This print assumes that desc->bd_export is not NULL. However, it is.
In fact it is expected to be NULL. desc->bd_import is the correct
structure to access in this case.
Lustre-change: http://review.whamcloud.com/7121
Intel-bug-id: https://jira.hpdd.intel.com/browse/LU-3585
Signed-off-by: Amir Shehata <amir.shehata@intel.com>
Reviewed-by: Liang Zhen <liang.zhen@intel.com>
Reviewed-by: Doug Oucharek <doug.s.oucharek@intel.com>
Reviewed-by: Oleg Drokin <oleg.drokin@intel.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: Andreas Dilger <andreas.dilger@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e2f9295f4c657500111514f92a3d3894d0e05b4 upstream.
Fast Channel Change across bands was enabled for
AR9462 recently, but this is causing baseband issues.
Disable it until this feature is tested well. Also,
remove the feature bit for AR9565 since it is
a single-band card and doesn't support this feature.
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit ff9a93f2ebb88ac7aab9568de80b64b92078e96d upstream.
Accessing the current channel definition in mac80211
when processing RX packets is problematic because it
could have been updated when a scan is issued. Since a
channel change involves flushing the existing packets
in the RX queue before a chip-reset is done, they would
be processed using the wrong band/channel information.
To avoid this, use the current channel information
maintained in the driver.
Reported-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 64e5acb09ca6b50c97299cff9ef51299470b29f2 upstream.
Use the right function to update frequency value.
If rx skb is probe response or beacon, the wrong frequency value can
cause problem that bss info can't be updated when it should be.
Fixes: 8318d78a44d4 ("cfg80211 API for channels/bitrates, mac80211 and driver conversion")
Signed-off-by: ZHAO Gang <gamerh2o@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 452028665312672c6ba9e16a19248ee00ead9400 upstream.
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0673effd41dba323d6a280ef37b5ef29f3f5a653 upstream.
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 09164043f63c947a49797750a09ca1cd7c31108e upstream.
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 91b0d1198417cf4fd9a7bd4138b6909f0b359099 upstream.
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2d93aee152b1758a94a18fe15d72153ba73b5679 upstream.
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
Fixes: 99cd47142399 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 1e202242ee1432d68a8bea4919b2ae0ef19d9e06 upstream.
bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9795229752c31da0c5f8a7dc4c827665327b52f9 upstream.
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f699273d6a624266ebc9198774f06ee64a3847a1 upstream.
The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d82403a9f407217b6aed5260aa92a120e8e98310 upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9b0784bb9de3152e787ee779868c626b137fb3b upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9806eacf5de27ab01d680c5d75c92a3a89734e4f upstream.
This patch uses the newly introduced power index register routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97204e93f01868eeba6ae5c4f3270f32905bb418 upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc6405712268fe514d3dd89aa936c4397b0871b9 upstream.
The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c908c74e005de780fddbe8cb6fcd44803f5d4b74 upstream.
Changes in the gain-control mechanism will require some changes in the header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 619ce76f8bb850b57032501a39f26aa6c6731c70 upstream.
The present code fails to set the linked state when an interface is
added.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9a758a8c905fc59e783ae91ad645452d877ea88 upstream.
The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62009b7f12793c932aaba0df946b04cb4a77d022 upstream.
Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8fd77aec1a9d6f4328fc0244f21932114e066df3 upstream.
This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65b9cc97c6852fae19dc5c7745e9abc8dd380aad upstream.
The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f87f960b2fb802f26ee3b00c19320e57a9c583ff upstream.
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit feffe09f510c475df082546815f9e4a573f6a233 upstream.
According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB
register error issue", All USB register write operations must
use the ARM SWP instruction. So, we implement a special ehci_write
for imx28.
Discussion for it at below:
http://marc.info/?l=linux-usb&m=137996395529294&w=2
Without this patcheset, imx28 works unstable at high AHB bus loading.
If the bus loading is not high, the imx28 usb can work well at the most
of time. There is a IC errata for this problem, usually, we consider
IC errata is a problem not a new feature, and this workaround is needed
for that, so we need to add them to stable tree 3.11+.
Cc: robert.hodaszi@digi.com
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 543d7784b07ffd16cc82a9cb4e1e0323fd0040f1 upstream.
There is a race in the hub driver between hub_disconnect() and
recursively_mark_NOTATTACHED(). This race can be triggered if the
driver is unbound from a device at the same time as the bus's root hub
is removed. When the race occurs, it can cause an oops:
BUG: unable to handle kernel NULL pointer dereference at 0000015c
IP: [<c16d5fb0>] recursively_mark_NOTATTACHED+0x20/0x60
Call Trace:
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d5fc4>] recursively_mark_NOTATTACHED+0x34/0x60
[<c16d6082>] usb_set_device_state+0x92/0x120
[<c16d862b>] usb_disconnect+0x2b/0x1a0
[<c16dd4c0>] usb_remove_hcd+0xb0/0x160
[<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<c1704efc>] ehci_mid_remove+0x1c/0x30
[<c1704f26>] ehci_mid_stop_host+0x16/0x30
[<c16f7698>] penwell_otg_work+0xd28/0x3520
[<c19c945b>] ? __schedule+0x39b/0x7f0
[<c19cdb9d>] ? sub_preempt_count+0x3d/0x50
[<c125e97d>] process_one_work+0x11d/0x3d0
[<c19c7f4d>] ? mutex_unlock+0xd/0x10
[<c125e0e5>] ? manage_workers.isra.24+0x1b5/0x270
[<c125f009>] worker_thread+0xf9/0x320
[<c19ca846>] ? _raw_spin_unlock_irqrestore+0x26/0x50
[<c125ef10>] ? rescuer_thread+0x2b0/0x2b0
[<c1264ac4>] kthread+0x94/0xa0
[<c19d0f77>] ret_from_kernel_thread+0x1b/0x28
[<c1264a30>] ? kthread_create_on_node+0xc0/0xc0
One problem is that recursively_mark_NOTATTACHED() uses the intfdata
value and hub->hdev->maxchild while hub_disconnect() is clearing them.
Another problem is that it uses hub->ports[i] while the port device is
being released.
To fix this race, we need to hold the device_state_lock while
hub_disconnect() changes the values. (Note that usb_disconnect()
and hub_port_connect_change() already acquire this lock at similar
critical times during a USB device's life cycle.) We also need to
remove the port devices after maxchild has been set to 0, instead of
before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: "Du, Changbin" <changbinx.du@intel.com>
Tested-by: "Du, Changbin" <changbinx.du@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9005355af23856c55a5538c9024355785424821b upstream.
If CONFIG_PCI is enabled, make sure xhci_cleanup_msix()
doesn't try to free a bogus PCI IRQ or dereference an invalid
pci_dev when the xHCI device is actually a platform_device.
This patch should be backported to kernels as old as 3.9, that
contain the commit 52fb61250a7a132b0cfb9f4a1060a1f3c49e5a25
"xhci-plat: Don't enable legacy PCI interrupts."
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0e16114f2db4838251fb64f3b550996ad3585890 upstream.
The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha
Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered
files are corrupted). A similar issue is described here:
http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170
The workaround is (MAX_SECTORS_64):
rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m
The patch adds the tested device to the unusual list permanently.
Signed-off-by: Mikhail Zolotaryov <lebon@lebon.org.ua>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1f15196ac3b541d084dc80a8fbd8a74c6a0bd44 upstream.
Genuine FTDI chips support only CS7/8. A previous fix in commit
8704211f65a2 ("USB: ftdi_sio: fixed handling of unsupported CSIZE
setting") enforced this limitation and reported it back to userspace.
However, certain types of smartcard readers depend on specific
driver behaviour that requests 0 data bits (not 5) to change into a
different operating mode if CS5 has been set.
This patch reenables this behaviour for all FTDI devices.
Tagged to be added to stable, because it affects a lot of users of
embedded systems which rely on these readers to work properly.
Reported-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Tested-by: Heinrich Siebmanns <H.Siebmanns@t-online.de>
Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 440ebadeae9298d7de3d4d105342691841ec88d0 upstream.
Fix ring-indicator (RI) status-bit definition, which was defined as CTS,
effectively preventing RI-changes from being detected while reporting
false RI status.
This bug predates git.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7d5c1b9c7cb5ec8e52b1adc65c484a923a8ea6c3 upstream.
Add support for iBall 3.5G connect usb modem.
$lsusb
Bus 002 Device 006: ID 1c9e:9605 OMEGA TECHNOLOGY
$usb-devices
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1c9e ProdID=9605 Rev=00.00
S: Manufacturer=USB Modem
S: Product=USB Modem
S: SerialNumber=1234567890ABCDEF
C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Rahul Bedarkar <rahulbedarkar89@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 4d90b819ae4c7ea8fd5e2bb7edc68c0f334be2e4 upstream.
Signed-off-by: Jun zhang <zhang.jun92@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 623c8263376c0b8a4b0c220232e7313d762cd0cc upstream.
Some PL2303 devices are known to lose bytes if you change serial
settings even to the same values as before. Avoid this by comparing the
encoded settings with the previsouly used ones before configuring the
device.
The common case was fixed by commit bf5e5834bffc6 ("pl2303: Fix mode
switching regression"), but this problem was still possible to trigger,
for instance, by using the TCSETS2-interface to repeatedly request
115201 baud, which gets mapped to 115200 and thus always triggers a
settings update.
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2fc5a7dace3c43e62402ab4e8800a8f1834ffe2a upstream.
We have met a bug that the high bandwidth ISO-TX transfer has failed
at the last packet if it is less than 1024, the TD status shows it
is "Transaction Error".
The root cause of this problem is: the mult value at qh is not correct
for current TD's transfer length. We use TD list to queue un-transfer
TDs, and change mult for new adding TDs. If new adding TDs transfer length
less than 1024, but the queued un-transfer TDs transfer length is larger
than 1024, the transfer error will occur, and vice versa.
Usually, this problem occurs at the last packet, and the first packet for
new frame.
We fixed this problem by setting Mult at QH as the largest value (3), and
set MultO (Multiplier Override) at TD according to every transfer length.
It can cover both hardware version less than 2.3 (the real mult is MultO
if it is not 0) and 2.3+ (the real mult is min(qh.mult, td.multo)).
Since the MultO bits are only existed at TX TD, we keep the ISO-RX behavior
unchanged.
For stable tree: 3.11+.
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Reported-by: Matthieu Vanin <b47495@freescale.com>
Tested-by: Matthieu Vanin <b47495@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
