| Age | Commit message (Collapse) | Author |
|---|
|
This adds scsi_build_sense_buffer, a simple helper function to build
sense data in a buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
SGI machines with WD33C93 allow usage of burst mode DMA, which increases
performance noticable. To make this selectable by the sgiwd93 stub,
setting the values for no_sync, fast and dma_mode has been moved to the
individual platform stubs.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
While performing hardware raid reset testing via the raid's client, I
noticed that sometimes, following the reset, that there would be more
raid targets in the lsscsi output than there actually were raid
targets. I tracked this down to the following issue.
Fusion cannot always find the mptsas_portinfo structure for the hba
because it uses the handle stored in ioc->handle to locate it. The
problem is that the firmware can change the handle associated with the
hba when h/w raid is reset (via the raid client). When this happens,
the driver will allocate another mptsas_portinfo structure and link it
into the chain of said structures. This ultimately causes confusion
within the driver resulting in targets not being removed when they
should be.
Eric Moore pointed out that the hba's portinfo structure is always the
first structure on the sas_topology list. This patch modifies
mptsas.c to access the hba's portinfo structure by taking the first
structure on said list.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch contains the following:
1. when hba completion status is good, check for iscsi transport
errors (underflow/overflow) prior to checking the scsi status
2. New firmware requires that one marker iocb be issued for each task
management command. The patch issues marker iocb immediately
following a LUN or Target reset.
Signed-off-by: David C Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add the new Controller (ID: 007C) support to driver.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When Driver sent wrong frame count to firmware. As this particular
command is sent to drive, FW is seeing continuous chip resets and so
the command will timeout.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Sense buffer ptr data type in the ioctl path is reverted back to u32 *
as in previous versions of driver.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The memory return from scsi_host_alloc is alloced by kzalloc, which is
already zero initilized, so memset not needed.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Cc: Adam Radford <linuxraid@amcc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This fixes a bug that we treat all sequencer operations as ands and
never do the additional invalid bit checks non-and operations require
because the if () to determine this has an operand which is always
true at the end of the or statement.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch removes lots of function declarations with moving
scsi_debug_queuecommand. This cleans up scsi_debug_queuecommand a bit
to silence checkpatch.pl
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This replaces list_for_each_safe and list_entry with
list_for_each_entry_safe.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
open_devip is always non NULL.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Two functions, sdebug_add_adapter and devInfoReg, creates new
scsi_debug devices. To simplify the code, this patch adds a new helper
function to create new scsi_debug devices (sdebug_device_create) and
converts both functions to use it.
I plan to add more to scsi_debug devices (e.g. using a thread for a
scsi_debug device for scalability testings). This patch enable me to
add such to just the new helper function instead of touching two
functions, sdebug_add_adapter and devInfoReg.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
sscanf can handle negative values.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This is needed by things like USB storage that want to set up static
commands for later use at start of day.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Since the way we allocate commands with a separate sense buffer is
getting complicated, we should isolate setup and teardown to a single
routine so that if it gets even more complex, there's only one place
in the code that needs to be altered.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This rewrites tw_transfer_internal with scsi_sg_copy_from/to_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Adam Radford <linuxraid@amcc.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This replaces stex_internal_copy with scsi_sg_copy_to/from_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This replaces aac_internal_transfer with scsi_sg_copy_to/from_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This rewrites ips_scmd_buf_write/read with scsi_sg_copy_from/to_buffer
respectively.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Salyzyn, Mark <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This replaces simscsi_fillresult with scsi_sg_copy_from_buffer.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Note that if scsi_bufflen(cmd) is not zero, the command always has an
sg list. So this patch doesn't do the error checking in
fill_from_dev_buffer and fetch_to_dev_buffer did.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Looks-OK-to: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
LLDs need to copies data between the SG table in struct scsi_cmnd and
liner buffer. So they use the helper functions like
sg_copy_from_buffer(scsi_sglist(sc), scsi_sg_count(sc), buf, buflen)
sg_copy_to_buffer(scsi_sglist(sc), scsi_sg_count(sc), buf, buflen)
This patch just adds wrapper functions:
scsi_sg_copy_from_buffer(sc, buf, buflen)
scsi_sg_copy_to_buffer(sc, buf, buflen)
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch adds new three helper functions to copy data between an SG
list and a linear buffer.
- sg_copy_from_buffer copies data from linear buffer to an SG list
- sg_copy_to_buffer copies data from an SG list to a linear buffer
When the APIs copy data from a linear buffer to an SG list,
flush_kernel_dcache_page is called. It's not necessary for everyone
but it's a no-op on most architectures and in general the API is not
used in performance critical path.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
We've verified that there are 64 bit and endianness problems in the
flashpoint driver. Reverse the logic of CONFIG_OMIT_FLASHPOINT (make
it CONFIG_SCSI_FLASHPOINT) and make it depend on X86_32 so it can't
appear for any other architectures. Long term, if someone chooses,
they could make FlashPoint 64 bit compliant (it looks like its a
question of fixing up the sizes in some of the packed descriptors)
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When a FSF physical close returns the status boxed, this means that
another system already closed the port. For our system this is the
same status as in the good path, we have to send the normal close. So,
set the status for the boxed response to the same as for the good
status.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
the semaphore inactive_list_mutex is used as a mutex, convert it to
the mutex API
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch modifies the driver to enable MSI by default for all SAS chips.
Signed-off-by: Sathya Prakash <sathya.prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
[based on proposal from Mike Christie <michaelc@cs.wisc.edu>, this
patch adds some simplifications to the handler functions]
With the new target reset handler callback in the SCSI midlayer, the
device reset handler in zfcp can be split in two parts. Now, zfcp does
not have to track anymore whether the device supports LUN resets, so
remove this flag and let the SCSI midlayer decide what to do.
The device reset handler simply issues a LUN reset and the target
reset handler a target reset.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This patch adds target reset functionalty.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: David Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
The problem is that serveral drivers are sending a target reset from the
device reset handler, and if we have multiple devices a target reset gets
sent for each device when only one would be sufficient. And if we do a target
reset it affects all the commands on the target so the device reset handler
code only cleaning up one devices's commands makes programming the driver a
little more difficult than it should be.
This patch adds a target reset handler, which drivers can use to send
a target reset. If successful it cleans up the commands for a devices
accessed through that starget.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
As we no longer need to calculate the data length of the whole scatterlist,
we can abort the loop earlier and coalesce req_len and act_len into one
variable, making fill_from_dev_buffer() more similar to fetch_to_dev_buffer().
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
scsi_debug.h just incldues some function declarations. This patch removes it
with moving the scsi_host_template.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
This converts scsi_debug to include header files in include/scsi/
instead of drivers/scsi/scsi.h.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Lots of drivers set it to 0. Remove that. Patch should be a nop.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When aacraid spoofs READ_CAPACITY_16, it assumes that the data length
in the sg list is equal to allocation length in cdb. But sg can put
any value in scb so the driver needs to check both the data length in
the sg list and allocation length in cdb.
If allocation length is larger than the response length that the
driver expects, it clears the data buffer in the sg list to zero but
it doesn't need to do. Just setting resid is fine.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Show the current binary tape driver and mode options is sysfs. A file
(options) is created in each directory in /sys/class/scsi_tape. The files
contain masks showing the options. The mask bit definitions are the same as
used when setting the options using the MTSETDRVBUFFER function in the
MTIOCTOP ioctl (defined in include/linux/mtio.h). For example:
> cat /sys/class/scsi_tape/nst0/options
0x00000d07
[jejb: updated doc with correction from Randy Dunlap]
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Add new option MT_ST_SILI to enable setting the SILI bit in reads in variable
block mode. If SILI is set, reading a block shorter than the byte count does
not result in CHECK CONDITION. The length of the block is determined using the
residual count from the HBA. Avoiding the REQUEST SENSE command for every
block speeds up some real applications considerably.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
These are no longer necessary.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Tested-by: Joerg Dorchain: <joerg@dorchain.net>
Tested-by: Stefan Priebe <s.priebe@allied-internet.ag>
Tested-by: Jon Chelton <jchelton@ffpglobal.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
lacks one
If the aic94xx chip doesn't have a SAS address in the chip's flash memory,
make libsas get one for us.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
Provide a facility to use the request_firmware() interface to get a SAS
address from userspace. This can be used by SAS LLDDs that cannot
obtain the address from the host adapter.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
I overlooked ips_scmd_buf_write and ips_scmd_buf_read when I converted
ips to use the data buffer accessors.
ips is unlikely to use sg chaining (especially in this path) since a)
this path is used only for non I/O commands (with little data
transfer), b) ips's sg_tablesize is set to just 17.
Thanks to Tim Pepper for testing this patch.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Mark Salyzyn <Mark_Salyzyn@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
- remove PCI device sort, which greatly simplifies PCI probe,
permitting direct, per-HBA function calls rather than an indirect
route to the same end result.
- remove need for pcistr[]
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
- Reduce uses of gdth_pci_str::pdev, preferring a local variable
(or function arg) 'pdev' instead.
- Reduce uses of gdth_pcistr array, preferring local variable
(or function arg) 'pcistr' instead.
- Eliminate lone use of gdth_pci_str::irq, using equivalent
pdev->irq instead
- Eliminate assign-only gdth_pci_str::io_mm
Note: If the indentation seems weird, that's because a line was
converted from spaces to tabs, when it was modified.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
