| Age | Commit message (Collapse) | Author |
|---|
|
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
|
|
Add at least the bare minimum of documentation for this chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This information was provided in lm-sensors ticket #2350:
http://www.lm-sensors.org/ticket/2350
This is IMHO still not enough to be able to safely implement fan
control support for the AS99127F, but this is valuable information so
I am adding it to the documentation.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support to set target temperature and tolerance for thermal
cruise mode.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for pwm_enable.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add PWM manual control.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
|
|
The lm87 driver normally assumes that firmware configured the chip
correctly. Since this is not always the case, alllow platform code to
set the channel register value via platform_data. All other
configuration registers can be changed after driver initialisation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
These Maxim chips are similar to MAX6657 but use unsigned temperature
values to allow for readings up to 145 degrees.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Support ADT7461 in extended temperature range mode, which will change
the range of readings from 0..127 to -64..191 degC. Adjust the
register conversion functions accordingly.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Update the links to the datasheet of some of the devices supported by
the lm90 driver. Also remove the links from the driver itself, so that
we don't have to update them twice each time they change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
The Maxim MAX6657, MAX6658 and MAX6659 have extra resolution bits for
the local temperature measurement. Let the lm90 driver read them and
export them to user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Martyn Welch <martyn.welch@gefanuc.com>
|
|
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Describe the sysfs files that were introduced in the ibmaem driver.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Minor documentation update to reflect the current full name of the power
management hardware interface and reflows the text a bit.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Drop the reset parameter of the w83627hf driver. It seems it wasn't
that useful. It was dropped from the Linux 2.4 version of this driver
back in July 2004.
The only users who have reported that they were still using this
parameter, needed it to switch the chip from automatic fan speed
control back to manual mode. Now that the driver creates pwmN_enable
sysfs files, users will be able to use these files instead, which is
way less agressive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dominik Geyer <dominik.geyer@gmx.de>
|
|
Update w83791d with fan bits in vbat mon register (7.48 of the
datasheet). This change allows all fans to have a divisor of 128,
and fixes a problem with incorrectly reported fan speeds.
Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add support for the SCH5027. The differences to the DME1737 are:
- No support for programmable temp offsets
- In auto mode, PWM outputs stay on min value if temp goes below low threshold
and can't be programmed to fully turn off
- Different voltage scaling
- No VID input
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Drop a lot of useless register defines, conversion macros, data structure
members and update code. All these register values were read from the
device but nothing is done out of them, so this is all dead code in
practice.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
This patch adds a module load parameter to enable probing of
non-standard LPC addresses 0x162e and 0x164e when scanning for supported
ISA chips.
Signed-Off-By: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
* Document the characteristics of libsensors 3.0.0 and 3.0.1.
* The sysfs interface is no longer subject to changes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Juerg Haefliger <juergh at gmail.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
This driver reads IBM Active Energy Manager energy/temperature/power
sensors on IBM System X hardware.
[akpm@linux-foundation.org: fix printk warnings]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a sentence about when fan speed increases to maximum.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There's nothing we can do about read errors on the W83L785TS-S, so
don't ask the user to report them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
This driver reports voltage, temperature and fan sensor readings
on an ADT7473 chip.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
This patch adds support for family 0x17, which has Penryn Core. It should also
cover the 8 cores Xeons.
Can someone test please? I think it should work.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Following patch will add reporting of maximum temperature, at which all fans
should spin full speed. It may be non-physical temperature on Desktop/Server CPUs.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
While the W83627EHF/EHG has only 6 VID pins, the W83627DHG has 8 VID
pins, to support VRD 11.0. Add support for this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Signed-off-by: Steve Hardy <steve@linuxrealtime.co.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
The W83627HF hardware monitoring features are supported by the
w83627hf driver for several years now. Support by the w83781d has
been advertised as deprecated 6 months ago, it's about time to see
it go.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
It's about time to reflect the move of the lm-sensors project to
lm-sensors.org.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
It happens that the Analog Devices ADM1024 is fully compatible with
the National Semiconductor LM87, so support for the former can easily
be added to the lm87 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
We've never seen any device supported by the lm78 or w83781d driver at
addresses 0x20-0x27, so let's stop probing these addresses. Extra probes cost
time, and have potential for confusing or misdetecting other I2C devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Update the hwmon sysfs interface documentation to include a specification
for power meters.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
This patch adds support for the SMSC SCH3112, SCH3114, and SCH3116 Super-I/O
chips. These chips feature identical hardware monitoring capabilites with the
expection that some of the fan inputs and pmw outputs don't exist.
The hardware monitoring features of the SCH311x chips can only be accessed via
the ISA bus. The driver therefore registers as a platform driver, if such a
chip is detected.
Signed-off-by: Juerg Haefliger <juergh at gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
This patch adds support for the Celeron 4xx based on Core 2 core.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Fix a bug in the code examples, make them comply with CodingStyle,
and indent them for a better redability.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Here is a patch adding some text to the sysfs interface documentation on how
settings written to sysfs attributes should be handled, focussing mainly on
error handling. This version incorperates Jean's latest comments.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Add individual alarm files to the lm78 driver, these are needed by
the next version of libsensors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Add support for the IT8716F and IT8718F fan4 and fan5. The late
revisions of the IT8712F have these too but support is harder to add
and nobody asked for it yet, so I didn't include it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Add new sysfs alarm methodology to w83791d driver
Signed-off-by: Charles Spirakis <bezaur@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
* Document the name attribute.
* Document the *_label attributes.
* Drop "typical usage" lists, they no longer match the reality.
* Drop non hardware-monitoring related entries.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
* Drop documentation of generic module parameters.
* Drop redundant section "Driver Description".
* Drop sample configuration section, it belongs to sensors.conf.eg.
* Random spelling and punctuation fixes.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
|
Deprecate the use of thermistor beta values as thermal sensor types.
No driver supports changing the beta value anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
|
