| Age | Commit message (Collapse) | Author |
|---|
|
The BCM2835 is an ARM SoC from Broadcom. This patch adds very basic
support for this SoC.
http://www.broadcom.com/products/BCM2835
http://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Note that the documentation in the latter .pdf assumes the MMU setup
that's used on the "VideoCore" companion processor, and does not document
physical peripheral addresses. Subtract 0x5e000000 to obtain the physical
addresses. This is accounted for by the ranges property in the /soc node
in the device tree.
The BCM2835 SoC is used in the Raspberry Pi. This patch also adds a
minimal device tree for this board; enough to see some very early kernel
boot messages through earlyprintk. However, this patch does not yet
provide a useful booting system.
http://www.raspberrypi.org/.
This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split from 3-4 months ago, and significantly stripped down and
modified since.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Dom Cobley <dc4@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
As specified by ftrace-design.txt, TIF_SYSCALL_TRACEPOINT was
added, as well as NR_syscalls in asm/unistd.h. Additionally,
__sys_trace was modified to call trace_sys_enter and
trace_sys_exit when appropriate.
Tests #2 - #4 of "perf test" now complete successfully.
Signed-off-by: Steven Walter <stevenrwalter@gmail.com>
Signed-off-by: Wade Farnsworth <wade_farnsworth@mentor.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
* tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: remove plat/board.h file
ARM: OMAP: move debug_card_init() function
ARM: OMAP1: move lcd pdata out of arch/arm/*
ARM: OMAP1: move omap1_bl pdata out of arch/arm/*
ARM: OMAP: remove the omap custom tags
ARM: OMAP1: remove the crystal type tag parsing
ARM: OMAP: remove the sti console workaround
ARM: OMAP: omap3evm: cleanup revision bits
ARM: OMAP: cleanup struct omap_board_config_kernel
+ sync to 3.6-rc5
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Kevin Hilman <khilman@ti.com>:
Updates for omap_device layer for v3.7.
Allows omap_device layer to keep track of driver bound status in order
to make more intelligent decisions about idling unused devices.
* tag 'devel-omap-device-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: omap_device: idle devices with no driver bound
ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
ARM: OMAP: omap_device: keep track of driver bound status
+ sync to 3.6-rc5
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/drivers
From Stephen Warren:
ARM: tegra: i2c driver enhancements mostly related to clocking
This branch contains a number of fixes and cleanups to the Tegra I2C
driver related to clocks. These are based on the common clock conversion
in order to avoid duplicating the clock driver changes before and after
the conversion. Finally, a bug-fix related to I2C_M_NOSTART is included.
This branch is based on previous pull request tegra-for-3.7-common-clk.
* tag 'tegra-for-3.7-drivers-i2c' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
...
+ sync to v3.6-rc4
Resolved remove/modify conflict in arch/arm/mach-sa1100/leds-hackkit.c
caused by the sync with v3.6-rc4.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: switch to the common clock framework
This branch contains a few bug-fixes, followed by a conversion of Tegra's
clock driver to the common clock framework, followed by various bug fixes
found after the conversion.
* tag 'tegra-for-3.7-common-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: Tegra: Add smp_twd clock for Tegra20
ARM: tegra: cpu-tegra: explicitly manage re-parenting
ARM: tegra: fix overflow in tegra20_pll_clk_round_rate()
ARM: tegra: Fix data type for io address
ARM: tegra: remove tegra_timer from tegra_list_clks
ARM: tegra30: clocks: fix the wrong tegra_audio_sync_clk_ops name
ARM: tegra: clocks: separate tegra_clk_32k_ops from Tegra20 and Tegra30
ARM: tegra: Remove duplicate code
ARM: tegra: Port tegra to generic clock framework
ARM: tegra: Add clk_tegra structure and helper functions
ARM: tegra: Rename tegra20 clock file
ARM: tegra20: Separate out clk ops and clk data
ARM: tegra30: Separate out clk ops and clk data
ARM: tegra: fix U16 divider range check
ARM: tegra: turn on UART A clock at boot
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/fixes-non-critical
* tag 'tegra-for-3.7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: enable SUSPEND/ARCH_SUSPEND_POSSIBLE for ARCH_TEGRA
ARM: tegra: fix debugfs entry for Tegra30
ARM: tegra: fix return value for debugfs init
|
|
This feature was added in 2009, I've been using it off and on and
never had any problems with it on my systems. I cannot see why
it needs to be marked experimental, make it a normal feature and
let us discover its possible shortcomings as people try to turn
it on instead.
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert vexpress to multi-platform. This always enables vexpress DT and
makes it the default v7 platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
|
|
This lets us build a multiplatform kernel for experimental purposes.
However, it will not be useful for any real work, because it relies
on a number of useful things to be disabled for now:
* SMP support must be turned off because of conflicting symbols.
Marc Zyngier has proposed a solution by adding a new SOC
operations structure to hold indirect function pointers
for these, but that work is currently stalled
* We turn on SPARSE_IRQ unconditionally, which is not supported
on most platforms. Each of them is currently in a different
state, but most are being worked on.
* A common clock framework is in place since v3.4 but not yet
being used. Work on this is on its way.
* DEBUG_LL for early debugging is currently disabled.
* THUMB2_KERNEL does not work with allyesconfig because the
kernel gets too big
[Rob Herring]: Rebased to not be dependent on the mass mach header rename.
As a result, omap2plus, imx, mxs and ux500 are not converted. Highbank,
picoxcell, mvebu, and socfpga are converted.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
|
|
Most platforms don't need mach/gpio.h and it prevents multi-platform
kernel images. Add CONFIG_NEED_MACH_GPIO_H and make platforns select it
if they need gpio.h. This is platforms that define __GPIOLIB_COMPLEX
or have lots of implicit includes pulled in by mach/gpio.h.
at91 and omap have gpio clean-up pending and can drop
CONFIG_NEED_MACH_GPIO_H once that is in.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
next/dt
* 'clk-3.7' of git://git.linaro.org/people/mturquette/linux:
clk: add of_clk_src_onecell_get() support
clk: ux500: Define smp_twd clock for u8500
mfd: dbx500: Provide a more accurate smp_twd clock
clk: ux500: Support for prmcu_rate clock
clk: Provide option for clk_get_rate to issue hw for new rate
clock: max77686: Add driver for Maxim 77686 32Khz crystal oscillator.
ARM: ux500: Switch to use common clock framework
clk: ux500: Clock definitions for u8500
clk: ux500: First version of clock definitions for ux500
clk: ux500: Adapt PRCMU and PRCC clocks for common clk
clk: versatile: make config option boolean
clk: add Loongson1B clock support
arm: mmp: make all SOCs use common clock by default
clk: mmp: add clock definition for mmp2
clk: mmp: add clock definition for pxa910
clk: mmp: add clock definition for pxa168
clk: mmp: add mmp specific clocks
clk: convert ARM RealView to common clk
clk: prima2: move from arch/arm/mach to drivers/clk
ARM: PRIMA2: convert to common clk and finish full clk tree
|
|
* 'clk' of git://github.com/hzhuang1/linux:
ARM: mmp: remove unused definition in APBC and APMU
ARM: mmp: move mmp2 clock definition to separated file
arm: mmp: move pxa910 clock definition to separated file
arm: mmp: move pxa168 clock definition to separated file
arm: mmp: make private clock definition exclude from common clock
+ Linux 3.6-rc4
|
|
* renesas/pmu:
ARM: shmobile: emev2: enable PMU(Performance Monitoring Unit)
ARM: shmobile: sh73a0: enable PMU(Performance Monitoring Unit)
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fixes from Marek Szyprowski:
"Another set of fixes for ARM dma-mapping subsystem.
Commit e9da6e9905e6 replaced custom consistent buffer remapping code
with generic vmalloc areas. It however introduced some regressions
caused by limited support for allocations in atomic context. This
series contains fixes for those regressions.
For some subplatforms the default, pre-allocated pool for atomic
allocations turned out to be too small, so a function for setting its
size has been added.
Another set of patches adds support for atomic allocations to
IOMMU-aware DMA-mapping implementation.
The last part of this pull request contains two fixes for Contiguous
Memory Allocator, which relax too strict requirements."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
ARM: dma-mapping: atomic_pool with struct page **pages
ARM: Kirkwood: increase atomic coherent pool size
ARM: DMA-Mapping: print warning when atomic coherent allocation fails
ARM: DMA-Mapping: add function for setting coherent pool size from platform code
ARM: relax conditions required for enabling Contiguous Memory Allocator
mm: cma: fix alignment requirements for contiguous regions
|
|
Even though system suspend/resume hasn't been validated on Tegra yet,
this Kconfig option needs to be enabled so that system shutdown is
reliable on an SMP system. Without it, I2C interrupts may be routed
to CPU0, whereas shutdown code may be running on CPU1, causing I2C
timeouts, preventing communication with the external PMIC.
This reverts 3d5e8af "ARM: disable SUSPEND/ARCH_SUSPEND_POSSIBLE for
ARCH_TEGRA".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
This patch converts tegra clock code to generic clock framework in following way:
- Implement clk_ops as required by generic clk framework. (tegraXX_clocks.c)
- Use platform specific struct clk_tegra in clk_ops implementation instead of struct clk.
- Initialize all clock data statically. (tegraXX_clocks_data.c)
Legacy framework did not have recalc_rate and is_enabled functions. Implemented these functions.
Removed init function. It's functionality is splitted into recalc_rate and is_enabled.
Static initialization is used since slab is not up in .init_early and clock
is needed to be initialized before clockevent/clocksource initialization.
Macros redefined for clk_tegra.
Also, single struct clk_tegra is used for all type of clocks (PLL, peripheral etc.). This
is to move quickly to generic common clock framework so that other dependent features will
not be blocked (such as DT binding).
Enabling COMMON_CLOCK config moved to ARCH_TEGRA since it is enabled for both Tegra20
and Tegra30.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
next/cleanup
Removes the pnx4008 platform support, which hasn't seen any active
development since 2006 and seems to be unused these days.
* 'pnx4008-removal' of git://git.antcom.de/linux-2.6:
ARM: mach-pnx4008: Remove architecture
|
|
http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
This cleans up the ks8695 timer driver and converts
it to use generic time and clock events.
* tag 'ks8695-time-for-arm-soc' of http://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ks8695: convert to generic time and clocksource
ARM: ks8695: delete resume hook from timer
ARM: ks8695: use [readl|writel]_relaxed()
ARM: ks8695: merge the timer header into the timer driver
|
|
Old platforms using ancient gettimeoffset() and other arcane
APIs are standing in the way of cleaning up the ARM kernel.
The gettimeoffset() was also broken: it would try to read out
the timer counter value, while this would not work (the
counter statically returns the initially programmed value)
so the implementation would anyway fall back to a homebrew
version of jiffie calculation.
This is an attempt at blind-coding a generic time and clocksource
driver for the platform by way of a datasheet and looking at the
old code.
Tested-by: Greg Ungerer <gerg@snapgear.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into next/cleanup
From Will Deacon:
Bunch of perf updates for the ARM backend that pave the way for
big.LITTLE support in the future. The separation of CPU and PMU code
is also the start of being able to move some of this stuff under
drivers/.
* tag 'arm-perf-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux:
ARM: perf: move irq registration into pmu implementation
ARM: perf: move CPU-specific PMU handling code into separate file
ARM: perf: prepare for moving CPU PMU code into separate file
ARM: perf: probe devicetree in preference to current CPU
ARM: perf: remove mysterious compiler barrier
ARM: pmu: remove arm_pmu_type enumeration
ARM: pmu: remove unused reservation mechanism
ARM: perf: add devicetree bindings for 11MPcore, A5, A7 and A15 PMUs
ARM: PMU: Add runtime PM Support
|
|
git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel into next/cleanup
* 'marco-prepare' of git://gitorious.org/sirfprima2-kernel/sirfprima2-kernel:
ARM: SIRF: make sirf irqchip driver optional since new SoCs will have GIC
ARM: PRIMA2: adjust Kconfig to support select SoC features
ARM: PRIMA2: use DT_MACHINE_START and convert to generic board
clk: prima2: move from arch/arm/mach to drivers/clk
ARM: PRIMA2: convert to common clk and finish full clk tree
|
|
The io-pci series has gained a merge to resolve a nontrivial
conflict.
* cleanup/io-pci:
ARM: Fix ioremap() of address zero
Also includes an update to Linux 3.6-rc3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As Stephen Rothwell reports, a849088aa155 ("ARM: Fix ioremap() of
address zero") from the arm-current tree and commit c2794437091a ("ARM:
Add fixed PCI i/o mapping") from the arm-soc tree conflict in
a nontrivial way in arch/arm/mm/mmu.c.
Rob Herring explains:
The PCI i/o reserved area has a dummy physical address of 0 and
needs to be skipped by ioremap searches. So we don't set
VM_ARM_STATIC_MAPPING to prevent matches by ioremap. The vm_struct
settings don't really matter when we do the real mapping of the
i/o space.
Since commit a849088aa155 is at the start of the fixes branch
in the arm tree, we can merge it into the branch that contains
the other ioremap changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Now that ATAGS support is well contained, we can easily remove it from
the kernel build if so desired. It has to explicitly be disabled, and
only when DT support is selected.
Note: disabling kernel ATAGS support does not prevent the usage of
CONFIG_ARM_ATAG_DTB_COMPAT.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This converts the Nomadik to using pin control using the
driver for the STN8815 ASIC.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
With icoll and gpio interrupt controllers adopt irqdomain support and
all interrupt nubmers are retrieved from device tree, it's safe to
select SPARSE_IRQ for mxs now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
As part of multi-platform effort, let's enable MULTI_IRQ_HANDLER for
mach-mxs and remove entry-macro.S.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Contiguous Memory Allocator requires only paging and MMU enabled not
particular CPU architectures, so there is no need for strict dependency
on CPU type. This enables to use CMA on some older ARM v5 systems which
also might need large contiguous blocks for the multimedia processing hw
modules.
Reported-by: Prabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Prabhakar Lad <prabhakar.lad@ti.com>
|
|
Now we have primaII, but will include Marco and Polo in mach-prima2
as well. We add Kconfig menu so that we can select necessary SoC
features.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
|
|
This patch removes the ARM architecture mach-pnx4008. No direct support or user
feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc
maintainers.
Signed-off-by: Roland Stigge <stigge@antcom.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for various ARM platforms. About half of these are for OMAP
and submitted before but did not make it into v3.6-rc2."
* tag 'fixes-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: don't select LEDS_GPIO for snowball
ARM: imx: build i.MX6 functions only when needed
ARM: imx: select CPU_FREQ_TABLE when needed
ARM: imx: fix ksz9021rn_phy_fixup
ARM: imx: build pm-imx5 code only when PM is enabled
ARM: omap: allow building omap44xx without SMP
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM: ux500: Ensure probing of Audio devices when Device Tree is enabled
ARM: ux500: Fix merge error, no matching driver name for 'snd_soc_u8500'
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
ARM: Kirkwood: fix Makefile.boot
ARM: Kirkwood: Fix iconnect leds
ARM: Orion: Set eth packet size csum offload limit
ARM: mv78xx0: fix win_cfg_base prototype
ARM: OMAP: dmtimers: Fix locking issue in omap_dm_timer_request*()
ARM: mmp: fix potential NULL dereference
ARM: OMAP4: Register the OPP table only for 4430 device
cpufreq: OMAP: Handle missing frequency table on SMP systems
ARM: OMAP4: sleep: Save the complete used register stack frame
...
|
|
This converts the ARM RealView machine over to using the common
clock. The approach is similar to the one used for the Integrator,
and we're reusing the ICST wrapper code.
We have to put the clock intialization in the timer init function
for the clocks to be available when initializing the timer,
keeping them in early_init() is too early for the common clk.
Since we now have to go down and compile drivers/clk/versatile
a CONFIG_COMMON_CLK_VERSATILE symbol has been added so the proper
code gets compiled into the kernel for either machine. A leftover
CLK_VERSATILE in the Integrator Kconfig was fixed up to use
the new symbol as well.
Tested on ARM RealView PB1176.
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
Commit 02c981c07bc95ac1e only implements a little part of primaII clk tree
due to common clk framework was not ready at that time.
This patch converts the old driver to common clk and finish the full clk
tree.
Signed-off-by: Binghua Duan <Binghua.Duan@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.
Building IMX without CPU_FREQ_TABLE results in:
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org
|
|
The PMU reservation mechanism was originally intended to allow OProfile
and perf-events to co-ordinate over access to the CPU PMU. Since then,
OProfile for ARM has moved to using perf as its backend, so the
reservation code is no longer used.
This patch removes the reservation code for the CPU PMU on ARM.
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
From Linus Walleij <linus.walleij@linaro.org>
This patch set does a number of cleanups and a minor improvement
to U300, paving the way for single zImage and device tree:
- Deprecate ancient platforms to make the following patches easier to
make...
- Move out one header to platform data and one to the mach-u300 proper
to depopulate <mach/*>
- Consolidate core machine files
- Convert to sparse IRQs
* 'u300-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: u300: convert to sparse IRQs
ARM: u300: move DMA channel header into mach-u300
ARM: u300: delete remnant clkdev.h file
ARM: u300: merge u300.c into core.c and rid headers
pinctrl/coh901: move header to platform data dir
pinctrl/coh901: retire ancient GPIO block versions
ARM: u300: retire ancient platforms
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Seems that Thomas' and my patches collided during the last merge
window.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
From Rob Herring <robherring2@gmail.com>:
This is the 2nd part of mach/io.h removals. This series removes io.h on
platforms with PCI by creating a fixed virtual I/O mapping and a common
__io() macro.
This version has changed a bit to accommodate Tegra converting its PCIe
host to a platform driver. Now the virtual space is only reserved during
early boot before .map_io() is called. The mapping is not created until
calling pci_ioremap_io which can be done at any point after vmalloc is
initialized.
I've gone back to fixed 64K windows for each PCI bus. This allows
removing all the i/o resource setup from the individually platforms and
placing it within the common ARM PCI code.
I've only tested versatilepb under qemu (with the model hacked up to
actually enable i/o space), so any testing is appreciated. iop3xx and
mv78xx0 have some risk of breaking as the PCI bus addresses are moved
to 0 from matching the cpu host bus addesss.
* cleanup/io-pci:
ARM: iop3xx: use fixed PCI i/o mapping
ARM: mv78xx0: use fixed pci i/o mapping
ARM: iop13xx: use fixed PCI i/o mapping
iop13xx: use more regular PCI I/O space handling
ARM: orion5x: use fixed PCI i/o mapping
ARM: kirkwood: use fixed PCI i/o mapping
ARM: dove: use fixed PCI i/o mapping
ARM: footbridge: use fixed PCI i/o mapping
ARM: shark: use fixed PCI i/o mapping
ARM: integrator: remove trailing whitespace on pci_v3.c
ARM: integrator: use fixed PCI i/o mapping
ARM: tegra: use fixed PCI i/o mapping
ARM: versatile: use fixed PCI i/o mapping
ARM: move PCI i/o resource setup into common code
ARM: Add fixed PCI i/o mapping
i2c: iop3xx: use standard gpiolib functions
i2c: iop3xx: clean-up trailing whitespace
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds into next/drivers
From Bryan Wu <bryan.wu@canonical.com>:
Based on Linus Walleij's ARM LED consolidation work, this patchset introduce a
new generic led trigger for CPU not only for ARM but also for others.
For enabling CPU idle event, CPU arch code should call ledtrig_cpu() stub to
trigger idle start or idle end event.
These patches convert old style LED driver in arch/arm to gpio_led or new led
driver interface. Against 3.5 release and build successfully for all the machines.
Test ledtrig-cpu driver on OMAP4 Panda board.
v9 --> v10
* fix compiling issue on versatile_defconfig reported by Russell King
* rebase to 3.5 kernel and move patches to new git tree
v8 --> v9:
* use mutex to replace rw_sema pointed out by Tim Gardner
* add a new struct led_trigger_cpu
* add lock_is_inited to record mutex lock initialization
v6 --> v7:
* add a patch to unify the led-trigger name
* fix some typo pointed
* use BUG_ON to detect CPU numbers during building stage
v5 --> v6:
* replace __get_cpu_var() to per_cpu()
* remove smp_processor_id() which is wrong with for_each_possible_cpu()
* test on real OMAP4 Panda board
* add comments about CPU hotplug in the CPU LED trigger driver
v4 --> v5:
* rebase all the patches on top of latest linux-next
* replace on_each_cpu() with for_each_possible_cpu()
* add some description of ledtrig_cpu() API
* remove old leds code from driver nwflash.c, which should use a new led trigger then
* this trigger driver can be built as module now
v3 --> v4:
* fix a typo pointed by Jochen Friedrich
* fix some building errors
* add Reviewed-by and Tested-by into patch log
v2 --> v3:
* almost rewrote the whole ledtrig-cpu driver, which is more simple
* every CPU will have a per-CPU trigger
* cpu trigger can be assigned to any leds
* fix a lockdep issue in led-trigger common code
* other fix according to review
v1 --> v2:
* remove select operations in Kconfig of every machines
* add back supporting of led in core module of mach-integrator
* solidate name scheme in ledtrig-cpu.c
* add comments of CPU_LED_* cpu led events
* fold patches of RealView and Versatile together
* add machine_is_ check during assabet led driver init
* add some Acked-by in patch logs
* remove code for simpad machine in machine-sa11000, since Jochen Friedrich
introduced gpiolib and gpio-led driver for simpad
* on Assabet and Netwinder machine, LED operations is reversed like:
setting bit means turn off leds
clearing bit means turn on leds
* add a new function to read CM_CTRL register for led driver
* 'for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
ARM: use new LEDS CPU trigger stub to replace old one
ARM: mach-sa1100: retire custom LED code
ARM: mach-omap1: retire custom LED code
ARM: mach-pnx4008: remove including old leds event API header file
ARM: plat-samsung: remove including old leds event API header file
ARM: mach-pxa: retire custom LED code
char: nwflash: remove old led event code
ARM: mach-footbridge: retire custom LED code
ARM: mach-ebsa110: retire custom LED code
ARM: mach-clps711x: retire custom LED code of P720T machine
ARM: mach-integrator: retire custom LED code
ARM: mach-integrator: move CM_CTRL to header file for accessing by other functions
ARM: mach-orion5x: convert custom LED code to gpio_led and LED CPU trigger
ARM: mach-shark: retire custom LED code
ARM: mach-ks8695: remove leds driver, since nobody use it
ARM: mach-realview and mach-versatile: retire custom LED code
ARM: at91: convert old leds drivers to gpio_led and led_trigger drivers
led-triggers: create a trigger for CPU activity
Conflicts:
arch/arm/mach-clps711x/p720t.c
arch/arm/mach-sa1100/leds-cerf.c
arch/arm/mach-sa1100/leds-lart.c
Let's hope this is the last time we pull this and it doesn't cause
more trouble. I have verified that version 10 causes no build
warnings or errors any more, and the patches still look good.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This converts the U300 to use sparse IRQs, which is simple now
that the number of machines are reduced.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that ARM has implemented its spinlocks with tickets we don't
need to use the generic lockbreak algorithm. Remove the Kconfig
from ARM so that we use the arch_spin_is_contended() definition
from the asm header. This also saves a word in each lock because
we don't need the break_lock member anymore.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Changes in v5:
- make XEN_DOM0 depend on XEN;
- avoid "select XEN_DOM0" in XEN.
Changes in v2:
- mark Xen guest support on ARM as EXPERIMENTAL.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
CC: Sergei Shtylyov <sshtylyov@mvista.com>
|
|
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
|
|
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
|
|
Rather than #define the options manually in the architecture code, add
Kconfig options for them and select them there instead. This also allows
us to select the compat IPC version parsing automatically for platforms
using the old compat IPC interface.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce CONFIG_ARCH_HAS_ATOMIC64_DEC_IF_POSITIVE and use this instead
of the multitude of #if defined() checks in atomic64_test.c
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull PWM subsystem from Thierry Reding:
"The new PWM subsystem aims at collecting all implementations of the
legacy PWM API and to eventually replace it completely.
The subsystem has been in development for over half a year now and
many drivers have already been converted. It has been in linux-next
for a couple of weeks and there have been no major issues so I think
it is ready for inclusion in your tree."
Arnd Bergmann <arnd@arndb.de>:
"Very much Ack on the new subsystem. It uses the interface
declarations as the previously separate pwm drivers, so nothing
changes for now in the drivers using it, although it enables us to
change those more easily in the future if we want to.
This work is also one of the missing pieces that are required to
eventually build ARM kernels for multiple platforms, which is
currently prohibited (amongs other things) by the fact that you cannot
have more than one driver exporting the pwm functions."
Tested-and-acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Philip, Avinash <avinashphilip@ti.com> # TI's AM33xx platforms
Acked-By: Alexandre Pereira da Silva <aletes.xgr@gmail.com> # LPC32XX
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Fix up trivial conflicts with other cleanups and DT updates.
* 'for-3.6' of git://gitorious.org/linux-pwm/linux-pwm: (36 commits)
pwm: pwm-tiehrpwm: PWM driver support for EHRPWM
pwm: pwm-tiecap: PWM driver support for ECAP APWM
pwm: fix used-uninitialized warning in pwm_get()
pwm: add lpc32xx PWM support
pwm_backlight: pass correct brightness to callback
pwm: Use pr_* functions in pwm-samsung.c file
pwm: Convert pwm-samsung to use devm_* APIs
pwm: Convert pwm-tegra to use devm_clk_get()
pwm: pwm-mxs: Return proper error if pwmchip_remove() fails
pwm: pwm-bfin: Return proper error if pwmchip_remove() fails
pwm: pxa: Propagate pwmchip_remove() error
pwm: Convert pwm-pxa to use devm_* APIs
pwm: Convert pwm-vt8500 to use devm_* APIs
pwm: Convert pwm-imx to use devm_* APIs
pwm: Conflict with legacy PWM API
pwm: pwm-mxs: add pinctrl support
pwm: pwm-mxs: use devm_* managed functions
pwm: pwm-mxs: use global reset function stmp_reset_block
pwm: pwm-mxs: encode soc name in compatible string
pwm: Take over maintainership of the PWM subsystem
...
|
