| Age | Commit message (Collapse) | Author |
|---|
|
This removes the "0x" prefix in front of the I2C DT device
address designation for each I2C DT node in the ux500
devicetree files.
Reported-by: Bryan Wu <cooloney@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch prepares the use of '#define' into dts files.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This root node is used in the whole family of chips, the a9500
is just one particular instance. Nodes should be named after
the type of object rather than identity.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com>
Reviewed-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The AB8500 GPIO driver has been un-BROKEN and rewritten as a pinctrl
driver. Now that it's back in use, let's ensure that it's available
when booting HREF with Device Tree enabled.
Cc: arm@kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Correct a typo in the Device Tree source file, where instead of
specifying property 'enable-gpio', which the driver is expecting
we specified 'gpio-enable' instead.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO numbers for the newly created gpio-regulator will differ from
board to board. Therefore it's not sensible to leave this information
in the top level DTSI file. Let's move them out to the DTS files
where they can correctly vary.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
So far, each ST-Ericsson board supported by Device Tree has been similar
enough to run though a single DT_MACHINE_INIT call. On the back of that
it has been suggested that we should reduce the number of compatible
strings in our dt_compat structure. After subsequent discussion with Arnd
Bergmann the conclusion was to list entries by platform as opposed to by
board.
The other suggestion was to use a single string which would cover all
supported platforms, but any wildcard entries would include unsupported
chipsets, such as the u5500 and potential new chips which no not yet have
DT functionality. Hence, the best solution which encompasses all supported
platforms, but no unsupported ones was to list the currently enabled four
chipsets; u8500, u8540, u9500 and u9540 instead.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
It is possible to connect a BU21013 Touch Screen to all version
of the HREF which support the ST-UIB. This patch applies all the
necessary settings to the pre-v60 and v60+ HREF Device Trees.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This is a skeleton creation which will be populated with the devices
found on one of ST-Ericsson's (UIB) User Interface Board.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Here we ensure the SFH7741 Proximity Sensor is registered through
gpio-keys when booting with Device Tree enabled.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
In ux500 platform code we currently support a number of devices.
Two of these devices are fairly similar, but have key differences.
Early (pre-v60) HREFs and the more up-to-date versions (v60+), and
they both need to be supported by Device Tree. Here we apply a DT
source file for the earlier versions.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
