| Age | Commit message (Collapse) | Author |
|---|
|
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
|
|
Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Put the clock to the devicetree, so the driver can take care of it
later. Then, we don't have to do the enabling as a workaround in board
init.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[shawn.guo: add enet_out into imx28.dtsi and overwrite it for m28evk]
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Slow down the I2C clock speed on M28 and SPS1 as it turns out the
I2C block in i.MX28 can not operate stable enough with the bus
running at 400kHz. Note that the driver used by Freescale runs
the bus at 250kHz when 400kHz speed is selected, but the mainline
Linux kernel runs the bus at actual 400kHz and that's where it is
occasionally unstable. Play safe and run the bus at 100kHz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch adds necessary DT properties to m28evk to enable touchscreen
in the LRADC block. The M28EVK is shipped with 4-wire resistive touchscreen.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The MMC WP is active high on the m28evk, fix this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Update the mach-mxs machine by removing the enet_clkout(). The new
revision of the board doesn't need that. Also, update the DTS file
with all the new drivers pulled in the mainline recently, that is,
SPI, LRADC, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
hog_pins is used to setup the pin functions, and it is not neccesarily used only
for GPIO pins, so use only 'hog' to describe a more generic term.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Rename mxs dts files with soc name being the prefix, so that the board
dts file can be located easily by soc name, and we also gain the
consistency of naming.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
