| Age | Commit message (Collapse) | Author |
|---|
|
We can now drop the call to ioremap_registers() as we have the binding for the
SDRAM/DDR Controller.
Drop ioremap_registers() for sam9x5 too.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Specified the main Oscillator via clock binding.
This will allow to do not hardcode it anymore in the DT board at 12MHz.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
http://www.calao-systems.com/articles.php?lng=en&pg=6099
this daughter board add the following device:
- Micro-SD socket
- TTL 3V3 - (Tx/Rx/RTS/CTS)
- I2C port
- 0.96" Serial OLED Display Module (over UART)
- MP3 decoder with Micro & Speakers
- 4x PB, 4x Leds (Blue), 3x Leds (Green, Orange, Red)
for now we add only the 2 UARTs, 4 Buttons, 7 leds and i2c via DT
used_led1 will not be re-add via DT as it's used by the motherboard too
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Use i2c-gpio and enable rv3029 RTC.
Enable the rtc in the sam9g20 defconfig.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
For now on use i2c-gpio driver on the same pin as the hardware IP.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Enable the nand in the cpu module with the partition.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Use a local copy of board informatin and fill with DT data.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
into next/cleanup
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
|
|
This patch adds initial dts file for EXYNOS5250 SoC. This dts
file is including the SoC specific devices and properties. And
adds the dts file for SMDK5250 board which uses the EXYNOS5250
dts file. Its board specific properites will be added later.
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into next/soc
* 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas: (234 commits)
ARM: shmobile: remove additional __io() macro use
ARM: mach-shmobile: default to no earlytimer
ARM: mach-shmobile: r8a7779 and Marzen timer rework
ARM: mach-shmobile: r8a7740 and Bonito timer rework
ARM: mach-shmobile: sh73a0, AG5EVM and Kota2 timer rework
ARM: mach-shmobile: sh7372, AP4EVB and Mackerel timer rework
ARM: mach-shmobile: sh7377 and G4EVM timer rework
ARM: mach-shmobile: sh7367 and G3EVM timer rework
ARM: mach-shmobile: add shmobile_earlytimer_init()
ARM: mach-shmobile: Move sh7372 AP4EVB external clk setup
ARM: mach-shmobile: Move sh7372 Mackerel external clk setup
ARM: mach-shmobile: rename clk_init() to shmobile_clk_init()
ARM: mach-shmobile: r8a7779 L2 cache support
ARM: mach-shmobile: r8a7779 map_io and init_early update
ARM: mach-shmobile: r8a7740 map_io and init_early update
ARM: mach-shmobile: sh73a0 map_io and init_early update
ARM: mach-shmobile: sh7372 map_io and init_early update
ARM: mach-shmobile: sh7377 map_io and init_early update
ARM: mach-shmobile: sh7367 map_io and init_early update
sh: remove clk_ops
...
(includes an update to v3.3-rc7)
Conflicts:
arch/arm/mach-omap2/id.c
|
|
Add support for the new smp_twd runtime registration interface
to the imx6q platforms, and remove the old compile-time support.
The imx6q DTS file is updated to match the TWD DT documentation.
Also present in this patch a DTS fix to the timer interrupt routing
(the PPI connection uses bits [15:8]) and trigger (rising edge).
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add support for the new smp_twd runtime registration interface
to the highbank platforms, and remove the old compile-time support.
The highbank DTS file is updated to match the TWD DT documentation
and fixes the timer trigger (rising edge).
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
* 'dt-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: mt_ventoux: very basic support for TeeJet Mt.Ventoux board
ARM: OMAP2+: Remove extra ifdefs for board-generic
ARM: OMAP2+: Fix build error when only ARCH_OMAP2/3 or 4 is selected
ARM: OMAP2+: board-generic: Use of_irq_init API
arm/dts: OMAP3: Add interrupt-controller bindings for INTC
ARM: OMAP2/3: intc: Add DT support for TI interrupt controller
|
|
* 'dt' of git://github.com/hzhuang1/linux: (6 commits)
Document: devicetree: add OF documents for arch-mmp
ARM: dts: append DTS file of pxa168
ARM: mmp: append OF support on pxa168
ARM: mmp: enable rtc clk in pxa168
i2c: pxa: add OF support
serial: pxa: add OF support
(plus update to v3.3-rc6)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
* 'next/cleanup-s3c24xx' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (24 commits)
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
ARM: S3C24XX: add get_rate for clk_p on S3C2416/2443
ARM: S3C24XX: add get_rate for clk_h on S3C2416/2443
ARM: S3C24XX: remove XXX_setup_clocks method from S3C2443
ARM: S3C24XX: remove obsolete S3C2416_DMA option
ARM: S3C24XX: Reuse S3C2443 dma for S3C2416
ARM: S3C24XX: Fix indentation of dma-s3c2443
ARM: S3C24XX: Move device setup files to mach directory
ARM: S3C24XX: Consolidate Simtec extensions
ARM: S3C24XX: move simtec-specific code to mach directory
ARM: S3C24XX: Move common-smdk code to mach directory
ARM: S3C24XX: Move s3c2443-clock.c to mach-s3c24xx
ARM: s3c2410_defconfig: update s3c2410_defconfig
ARM: S3C2443: move mach-s3c2443/* into mach-s3c24xx/
ARM: S3C2440: move mach-s3c2440/* into mach-s3c24xx/
ARM: S3C2416: move mach-s3c2416/* into mach-s3c24xx/
ARM: S3C2412: move mach-s3c2412/* into mach-s3c24xx/
ARM: S3C2410: move mach-s3c2410/* into mach-s3c24xx/
ARM: S3C24XX: change the ARCH_S3C2410 to ARCH_S3C24XX
ARM: S3C2410: move s3c2410_baseclk_add to clock.h
...
|
|
The USB1 port on Tegra2 supports operation in host or device modes. On
Seaboard this is possible, so mark the port as OTG.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Tegra's USB1 port supports legacy mode, so mark it as such. Even if we
don't use it, we must turn it off in the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
DTS files of both PXA168 and aspenite are appended.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Very basic support for TeeJet Mt.Ventoux board. Able to boot via
board-generic and ramdisk/initramfs, however most of peripherals are
not supported. Produces tons of twl4030 related errors as this board
doesn't have twl4030 installed.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/boards
Tegra board updates. Most of the board updates for tegra30 and for some
of the driver device-tree conversions have gone in through the other
branches, so that leaves quite little left here -- mostly a couple
of updates to the not-yet-converted tegra2 boards and a couple of
device-tree updates.
* tag 'tegra-boards' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ARM: tegra: match SoC name not board name in DT board files
ARM: tegra: PCIe: Provide 3.3V supply voltage
ARM: dt: tegra: add the wifi led to paz00 device tree
ARM: dt: tegra: add the power gpio key to paz00 device tree
ARM: dt: tegra: add ADT7461 temperature sensor to paz00 device tree
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/soc-drivers
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra into tegra/dt
Device tree updates for tegra. Various development, including a handful
of additions to the tegra30 device trees.
* tag 'tegra-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra:
ASoC: DT: Add digital microphone binding to PAZ00 board.
ARM: dt: Add ARM PMU to tegra*.dtsi
ARM: dt: Add SD controller configuration to Tegra Cardhu
ARM: dt: tegra: Enable headset autodetection on PAZ00 board.
ARM: dt: tegra: Enable device tree audio codec on PAZ00 board.
ARM: dt: Add binding for Tegra PMC
ARM: dt: tegra: Enable audio on WM8903 boards, disable others
ARM: dt: tegra: Add labels for I2S controllers
ARM: dt: tegra: Modify I2S nodes to match binding
ARM: dt: tegra: Add Tegra APB DMA device tree binding
ARM: dt: tegra30.dtsi: Add extra GPIO interrupt
ARM: dt: tegra30.dtsi: Reformat gpio's interrupts property
dt: tegra gpio: Flesh out binding documentation
ARM: tegra: seaboard: add EMC table to device tree
ARM: tegra: emc: device tree bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The ports are used as follows:
UART1/A: Routed to debug dongle
UART2/B: GPS
UART3/C: Bluetooth
UART4/D: Routed to debug dongle
UART5/E: Not connected
The debug dongle has jumpers to connect either UART1/A or UART4/D to
the DB-9 connector. UART1/A is typically used on Cardhu, and is the option
we assume here.
For now, only enable UART1/A, and explicitly disable all other ports.
The explicit disable prevents the message "of_serial 70006040.serial:
no clock-frequency property set" being printed during boot.
Enabling the other ports requires their clocks to be enabled, or accesses
to the registers will hang. At present, this requires adding entries into
board-dt-tegra30.c's tegra_dt_clk_init_table[]. Lets punt on that and wait
for the common clock bindings to set this all up, although that will also
requiring adding clock support to 8250.c.
While we're at it, fix board-dt-tegra30.c to enable the correct clock for
the debug UART. We got away with this before, because the bootloader already
enabled it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch adds device tree binding of digital microphone to PAZ00
board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This enables HW performance measurements, and usage of the "perf" tool.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch changes the ARCH name to "ARCH_S3C24XX" for Samsung
S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443,
and S3C2450 SoCs so that we can merge the mach-xxx directories
and plat-s3c24xx dir. to just one mach-s3c24xx for them.
I think this should be sent to upstream via samsung tree because
this touches many samsung stuff.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
[for the gadget part:]
Acked-by: Felipe Balbi <balbi@ti.com>
[for the framebuffer (video) part:]
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
[For the watchdog-part:]
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
git://git.pengutronix.de/git/imx/linux-2.6 into next/dt
* 'features/imx27-dt' of git://git.pengutronix.de/git/imx/linux-2.6:
devicetree-bindings: Add documentation for i.MX generic boards
ARM i.MX: Add phytec phycore-i.MX27 (aka pcm038) devicetree support
ARM i.MX27: Add devicetree support
|
|
into next/dt
* 'at91-3.4-cleanup2+DT' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91: at91sam9x5cm/dt: add leds support
ARM: at91: usb_a9g20/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add gpio-keys support
ARM: at91: at91sam9m10g45ek/dt: add leds support
ARM: at91: usb_a9g20/dt: add leds support
ARM: at91/pio: add new PIO3 features
ARM: at91: add sam9_smc.o to at91sam9x5 build
ARM: at91/tc/clocksource: Add 32 bit variant to Timer Counter
ARM: at91/tc: add device tree support to atmel_tclib
ARM: at91/tclib: take iomem size from resource
ARM: at91/pit: add traces in case of error
ARM: at91: pit add DT support
ARM: at91: AIC and GPIO IRQ device tree initialization
ARM: at91/board-dt: remove AIC irq domain from board file
ARM: at91/gpio: remove the static specification of gpio_chip.base
ARM: at91/gpio: add .to_irq gpio_chip handler
ARM: at91/gpio: non-DT builds do not have gpio_chip.of_node field
ARM: at91/gpio: add irqdomain and DT support
ARM: at91/gpio: change comments and one variable name
ARM/USB: at91/ohci-at91: remove the use of irq_to_gpio
...
|
|
These two branches are a dependency for the at91 device tree changes,
so we pull them in here. at91/base2+cleanup will get merged through
the arm-soc cleanup2 branch, while the irqdomain tree will be sent
by Grant before this one gets integrated.
Conflicts:
drivers/rtc/rtc-at91sam9.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Use the gpio for d7 as we do not support yet the pwm led via dt.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
This patch adds the support for new PIO controller found on some
at91sam SOCs.
- more peripheral multiplexing
- more features to configure on a PIO (pull-down, Schmitt trigger, debouncer)
- support for several IRQ triggering features (type and polarity)
Support for those new features are retrieved from the device tree
compatibility string.
Debugfs at91_gpio file is updated to monitor configuration.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Device tree support added to atmel_tclib: the generic Timer Counter
library. This is used by the clocksource/clockevent driver tcb_clksrc.
The current DT enabled platforms are also modified to use it:
- .dtsi files are modified to add Timer Counter Block entries
- alias are created to allow identification of each block
- clkdev lookup tables are added for clocks identification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Retreive registers address and IRQ from device tree entry.
Called from at91_dt_init_irq() so that timers are up-n-running
when timers initialization will occur.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change error path and interrupts property handling]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add "legacy" type of irqdomain to preserve old-style numbering
and allow smooth transition for both DT and non-DT cases.
Original idea and code by Jean-Christophe Plagniol-Villard.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Add an irqdomain for the AIC interrupt controller.
The device tree support is mapping the registers and
is using the irq_domain_add_legacy() to manage hwirq
translation.
The documentation is describing the meaning of the
two cells required for using this "interrupt-controller"
in a device tree node.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
* 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Add support for TI OMAP3 EVM board
arm/dts: OMAP4: Update DTS file with new GIC bindings
arm/dts: OMAP3: Add i2c controller nodes
arm/dts: OMAP4: Add i2c controller nodes
ARM: OMAP2+: Set Kconfig dependencies for PROC_DEVICETREE
arm/dts: OMAP3&4: Remove the '0x' prefix for serial nodes
ARM: OMAP1: kconfig: Enable IRQ_DOMAIN by default for OMAP1 platforms
ARM: OMAP2+: pm: Do not init statically the SR and voltage layer with DT
ARM: OMAP2+: omap_device: Replace dev_warn by dev_dbg in omap_device_build_from_dt
ARM: OMAP2+: board-generic: Remove un-needed .atag_offset for DT_MACHINE
ARM: OMAP2+: kconfig: Enable devicetree by default for OMAP2+ systems
arm/dts: OMAP: Remove bootargs node from board files
|
|
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
This patch adds basic devicetree support for i.MX27 based SoCs.
Only the bindings for which drivers exist are added here:
- UART
- fec
- CSPI
- I2C
- watchdog
- gpio
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
next/boards
* 'board-specific' of git://github.com/hzhuang1/linux: (5 commits)
ARM: pxa: add dummy clock for pxa25x and pxa27x
ARM: mmp: append irq name of gpio device
pxa/hx4700: Fix PXA_GPIO_IRQ_BASE/IRQ_NUM values
pxa/hx4700: Add ASIC3 LED support
pxa/hx4700: Correct StrataFlash block size discovery
(update to v3.3-rc5)
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
* 'imx/defconfig' of git://git.linaro.org/people/shawnguo/linux-2.6: (2 commits)
ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
ARM: imx: update imx_v6_v7_defconfig
(upadte to v3.3-rc5)
|
|
next/dt
* 'imx/dt' of git://git.linaro.org/people/shawnguo/linux-2.6: (7 commits)
ARM: dts: imx6q-sabrelite: add vmmc-supply for usdhc
ARM: dts: imx6q-arm2: add vmmc-supply for usdhc
ARM: dts: imx51-babbage: update mc13892 device
ARM: dts: imx6q-sabrelite: add sgtl5000 audio codec
ARM: dts: imx6q-sabrelite: add 2p5v and 3p3v regulators
ARM i.MX5/6: Add dt support for generic boards
ARM: imx5: generate dtbs for imx5 boards
(update to Linux 3.3-rc5)
|
|
into devicetree/merge
|
|
This uart is the primary console for the dreamplug. Removed
kirkwood_uart0_init() call from board-dt.c.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
