| Age | Commit message (Collapse) | Author |
|---|
|
Setup and remove the interrupt handler in clock event mode selection.
This avoids calling the (shared) interrupt handler when the device is
not used.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: redo the patch with NR_IRQS_LEGACY which is probably required since
commit 8fe82a55 ("ARM: at91: sparse irq support") which is included since v3.6.
Patch based on what Sami Pietikäinen <Sami.Pietikainen@wapice.com> suggested].
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
|
|
Setup and remove the interrupt handler in clock event mode selection.
This avoids calling the (shared) interrupt handler when the device is
not used.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: redo the patch with NR_IRQS_LEGACY which is probably required since
commit 8fe82a55 ("ARM: at91: sparse irq support") which is included since v3.6.
Patch based on what Sami Pietikäinen <Sami.Pietikainen@wapice.com> suggested].
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
|
|
Setup and remove the interrupt handler in clock event mode selection.
This avoids calling the (shared) interrupt handler when the device is
not used.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: redo the patch with NR_IRQS_LEGACY which is probably required since
commit 8fe82a55 ("ARM: at91: sparse irq support") which is included since v3.6.
Patch based on what Sami Pietikäinen <Sami.Pietikainen@wapice.com> suggested].
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
commit 1588c51cf6d782e63a8719681d905ef0ac22ee62 upstream.
There was a copy/paste error when reading the nwe_pulse value.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@traphandler.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 58e7b1d5826ac6a64b1101d8a70162bc084a7d1e upstream.
With some devices, transfer hangs during I2C frame transmission. This issue
disappears when reducing the internal frequency of the TWI IP. Even if it is
indicated that internal clock max frequency is 66MHz, it seems we have
oversampling on I2C signals making TWI believe that a transfer in progress
is done.
This fix has no impact on the I2C bus frequency.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 94c4c79f2f1acca6e69a50bff5a7d9027509c16b upstream.
Make sure the RTT-interrupts are masked at boot by adding a new helper
function to be used at SOC-init.
This fixes hanged boot on all AT91 SOCs with an RTT, for example, if an
RTT-alarm goes off after a non-clean shutdown (e.g. when using RTC
wakeup).
The RTC and RTT-peripherals are powered by backup power (VDDBU) (on all
AT91 SOCs but RM9200) and are not reset on wake-up, user, watchdog or
software reset. This means that their interrupts may be enabled during
early boot if, for example, they where not disabled during a previous
shutdown (e.g. due to a buggy driver or a non-clean shutdown such as a
user reset). Furthermore, an RTC or RTT-alarm may also be active.
The RTC and RTT-interrupts use the shared system-interrupt line, which
is also used by the PIT, and if an interrupt occurs before a handler
(e.g. RTC-driver) has been installed this leads to the system interrupt
being disabled and prevents the system from booting.
Note that when boot hangs due to an early RTC or RTT-interrupt, the only
way to get the system to start again is to remove the backup power (e.g.
battery) or to disable the interrupt manually from the bootloader. In
particular, a user reset is not sufficient.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6de714c21a8ea315fffba6a93bbe537f4c1bf4f0 upstream.
Make sure the RTC-interrupts are masked at boot by adding a new helper
function to be used at SOC-init.
This fixes hanged boot on all AT91 SOCs with an RTC (but RM9200), for
example, after a reset during an RTC-update or if an RTC-alarm goes off
after shutdown (e.g. when using RTC wakeup).
The RTC and RTT-peripherals are powered by backup power (VDDBU) (on all
AT91 SOCs but RM9200) and are not reset on wake-up, user, watchdog or
software reset. This means that their interrupts may be enabled during
early boot if, for example, they where not disabled during a previous
shutdown (e.g. due to a buggy driver or a non-clean shutdown such as a
user reset). Furthermore, an RTC or RTT-alarm may also be active.
The RTC and RTT-interrupts use the shared system-interrupt line, which
is also used by the PIT, and if an interrupt occurs before a handler
(e.g. RTC-driver) has been installed this leads to the system interrupt
being disabled and prevents the system from booting.
Note that when boot hangs due to an early RTC or RTT-interrupt, the only
way to get the system to start again is to remove the backup power (e.g.
battery) or to disable the interrupt manually from the bootloader. In
particular, a user reset is not sufficient.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Like we are doing on DDR0 we need to cleanly shutdown DDR1 if it is
used before rebooting.
If DDR1 is not initialized, we check it and avoid dereferencing its address.
Even by adding two more instructions, we are able to complete the procedure
within a single cache line.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This flag is a NOOP since 2.6.36 and can be removed.
This is an update for 3.11 of a patch already sent for 3.10
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree merge from Greg KH:
"Here's the bit staging tree pull request for 3.12-rc1.
Lots of staging driver updates, and fixes. Lustre is finally enabled
in the build, and lots of cleanup started happening in it. There's a
new wireless driver in here, and 2 new TTY drivers, which cause the
overall lines added/removed to be quite large on the "added" side.
The IIO driver updates are also coming through here, as they are tied
to the staging iio drivers"
* tag 'staging-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (942 commits)
staging: dwc2: make dwc2_core_params documentation more complete
staging: dwc2: validate the value for phy_utmi_width
staging: dwc2: interpret all hwcfg and related register at init time
staging: dwc2: properly mask the GRXFSIZ register
staging: dwc2: remove redundant register reads
staging: dwc2: re-use hptxfsiz variable
staging: dwc2: simplify debug output in dwc_hc_init
staging: dwc2: add missing shift
staging: dwc2: simplify register shift expressions
staging: dwc2: only read the snpsid register once
staging: dwc2: unshift non-bool register value constants
staging: dwc2: fix off-by-one in check for max_packet_count parameter
staging: dwc2: remove specific fifo size constants
Staging:BCM:DDRInit.c:Renaming __FUNCTION__
staging: bcm: remove Version.h file.
staging: rtl8188eu: off by one in rtw_set_802_11_add_wep()
staging: r8188eu: copying one byte too much
staging: rtl8188eu: || vs && typo
staging: r8188eu: off by one bugs
staging: crystalhd: Resolve sparse 'different base types' warnings.
...
|
|
From Nicolas Ferre:
AT91 SoC update for 3.12 take 1
- enable kernel uncompress information output for
SoC where it was missing: at91sam9n12 and sama5d3
- addition of at91rm9200 to the generic at91_dt_defconfig
* tag 'at91-soc' of git://github.com/at91linux/linux-at91:
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: at91: sam9n12: enable kernel uncompress info output
ARM: at91: sama5: enable kernel uncompress info output
ARM: at91: include sama5d3.h into hardware.h
ARM: at91: sama5d3: add definition for usart base address
|
|
For at91 boards, there are different IPs for adc. Different IPs has different
STARTUP & PRESCAL mask in ADC_MR.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
As use the multiple compatible string, we can remove hardware register in dt.
CC: devicetree@vger.kernel.org
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch moves the pca953x.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add defines for common Micrel PHY setups so that other platforms
can use them. Update imx61 and sama5 hardware to use the micrel_phy.h
PHY defines.
Also add support for the KSZ9021RLRN PHY.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The sam9n12 use the same array usart as sam9x5, add it which will
enable output kernel uncompress info:
---8>---
Uncompressing Linux... done, booting the kernel.
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Enable kernel uncompress info output, which will show as following:
---8>---
Uncompressing Linux... done, booting the kernel.
---<8---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Add clocks to clock lookup table for uart DT entries.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"This contains cleanups as preparation for other branches adding new
features, we pulled 16 branches for 9 platforms into this one.
Most notable here is the removal of support for ATAGS based OMAP4
systems. Since all OMAP4 machines are fully functional with DT based
booting in 3.10, we can remove a lot of code here.
Also noteworthy is Maxime Ripard's cleanup of the machine descriptors,
which means we need no machine descriptors in a lot more cases and can
boot additional machines by just having the respective device drivers
enabled."
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (76 commits)
ARM: picoxcell: remove .nr_irqs reference
ARM: s5p64x0: avoid build warning for uncompress.h
ARM: SAMSUNG: Remove unused plat/regs-watchdog.h header
ARM: SAMSUNG: Remove legacy watchdog reset code
ARM: SAMSUNG: Let platforms use the new watchdog reset driver
ARM: SAMSUNG: Add watchdog reset driver
ARM: SAMSUNG: Use local definitions of watchdog registers
watchdog: s3c2410_wdt: Use local register definitions
ARM: S5P64X0: Use common uncompress.h part for plat-samsung
ARM: SAMSUNG: Consolidate uncompress subroutine
ARM: at91: drop rm9200dk board support
ARM: dts: msm: Fix merge resolution
ARM: OMAP1: Remove dma.h
ARM: OMAP1: Remove legacy irda.h and irda setup from board files
ARM: OMAP1: Remove duplicated DMA channel definitions
ARM: OMAP1: Remove McBSP DMA channel definitions
ARM: OMAP2+: Remove dma.h
ARM: OMAP2+: hwmod: Remove remaining DMA channel definitions
ARM: OMAP2+: Remove duplicated DMA channel definitions
ARM: OMAP2+: Remove AES crypto device DMA channel definitions
...
|
|
We are using this function, now that we have introduced
the support for UTMI clock for computing the USB host rate.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
|
|
at91sam9n12 has Full-speed only USB. So we should add
it to the list in at91_pllb_usbfs_clock_init() function.
Moreover, at91sam9n12 has an unusual PMC in the sense that it
has a PLLB but also has a USB clock register.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
|
|
The following commit:
commit 7e348b9012522fa0efd854d20d210d5e57fcedd1
Author: Robert Lee <rob.lee@linaro.org>
Date: Tue Mar 20 15:22:43 2012 -0500
ARM: at91: Consolidate time keeping and irq enable
Enable core cpuidle timekeeping and irq enabling and remove that
handling from this code.
introduced an additional zero to the state1 (suspend) target residency.
With a periodic tick, the cpu never enters the state1 with both 10000 and
100000.
With a tickless system, it enters to state1 much more often with the
initial value, roughly x7 more.
Fix it by setting the value to 10ms again.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[nicola.ferre@atmel.com: add precisions given by Daniel to commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Since 4b68520dc0ec96153bc0d87bca5ffba508edfcf
ARM: at91: add AIC5 support
we allocate the at91_extern_irq.
This patch makes it static and stores the non-dt extern irq in the soc
structure. It is then possible to use a at91_get_extern_irq() function
to get the value for outside of the irq driver. It is useful for passing
its value to at91_aic_init().
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
[nicolas.ferre@atmel.com: rework commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
next/cleanup
From Nicolas Ferre:
One old board removal.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91: drop rm9200dk board support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This board is impossible to found anymore.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Because MT_DEVICE is not executable in armv7, we change
the internal SRAM memory type to MT_MEMORY_NONCACHED.
As it seems that caching this internal SRAM memory is not necessary,
we chose the this memory type.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Fixes:
arch/arm/mach-at91/built-in.o: In function `ksz9021rn_phy_fixup':
:(.text+0x1174): undefined reference to `mdiobus_write'
:(.text+0x1188): undefined reference to `mdiobus_write'
:(.text+0x119c): undefined reference to `mdiobus_write'
:(.text+0x11b0): undefined reference to `mdiobus_write'
arch/arm/mach-at91/built-in.o: In function `sama5_dt_device_init':
:(.init.text+0x1e34): undefined reference to `phy_register_fixup_for_uid'
when CONFIG_PHYLIB is not selected.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
From Nicolas Ferre:
Again some nice DT updates for AT91:
- DMA binding update with one patch shared with slave-dma tree
- more SPI DT activation
- enable the USB gadget HS for DT platforms
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9m10g45ek add udc DT support
ARM: at91: sam9g45 add udc DT support
ARM: at91: sam9x5ek add udc DT support
ARM: at91: sam9x5 add udc DT support
ARM: at91: dt: at91sam9x5: add SPI DMA client infos
ARM: at91: dt: switch DMA DT bindings to pre-processor
ARM: at91: dt: add header to define at_hdmac configuration
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
|
|
From Nicolas Ferre:
Big DT-centric update for AT91:
- Calao boards update, removal of one board C file and
associated defconfig, Kconfig Makefile lines
- several Acme boards updates
- addition of watchdog, uart and pinctrl descriptions for
several products
- modification of RTC compatible string for 9x5 family
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/dt: add pinctrl definition for at91 tc blocks
ARM: at91/dts: add the watchdog nodes for at91 boards
ARM: at91/dtsi: add the watchdog nodes for at91 SoC
ARM: at91: drop non DT: Calao USB-A96x
ARM: at91: dt: add Calao USB-A9G20 low power version
ARM: at91: dt: usb-a9263: add dataflash support
ARM: at91: dt: usb-a9263: update shutdown controller
ARM: at91: dt: usb-a9260: update shutdown controller
ARM: at91: dt: sam9260: add i2c gpio pinctrl
ARM: at91: switch Fox G20 board .dts to pre-processor defines
ARM: at91: add Acme Systems Fox G20 board
ARM: at91/at91-ariag25.dts: UART0/1 nodes are disabled
ARM: at91/at91sam9x5.dtsi: add UART0/1 nodes
ARM: at91/at91-ariag25.dts: add RTC node
ARM: at91: at91sam9x5 RTC is not compatible with at91rm9200 one
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
as now we have full DT support of those board
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
next/cleanup
From Nicolas Ferre:
Big update converting pinctrl to use macros and header files. Increases
readability and avoids typos.
Update of AT91 defconfigs and merge of defconfigs for the similar SoCs
sam9260/9g20 and sam9261/9g10.
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91:
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
ARM: at91: dt: use #include for all device trees
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Merge 9g20 with 9260 and 9g10 with 9261 as those SoCs can run from the same
kernel even in non DT world.
Fix the sam9261ek to allow 9g10 and sam9261 to compile together.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
since commit 838a2ae80a6ab52139fb1bf0a93ea8c5eff94488
Author: Shawn Guo <shawn.guo@linaro.org>
Date: Sat Jan 12 11:50:05 2013 +0000
ARM: use clockevents_config_and_register() where possible
The timer is wrongly configured and result in a nice crash
so revert it on rm9200 timer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: stable <stable@vger.kernel.org> # 3.8+
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
|
|
There is no reason to keep the clksrc cleanups separate from the
other cleanups, and this resolves some merge conflicts.
Conflicts:
arch/arm/mach-spear/spear13xx.c
drivers/irqchip/Makefile
|
