| Age | Commit message (Collapse) | Author |
|---|
|
Move the IRQ handler along side the rest of the IRQ code, and rearrange
the include files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than having direct register accesses to NCR_0 scattered amongst
the code, provide a function instead. This contains the necessary
race protection for this platform, ensuring that updates to this
register are safe.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Since ARM was converted to genirq, the neponset IRQ implementation has
gradually broken as a result of various subtle changes being introduced
into genirq.
It used to be that simple IRQs did not need an IRQ chip. This is no
longer the case, and genirq barfs in irq_set_handler(). Fix this by
introducing a dummy no-op chip, and registering it along with the flow
handler.
Neponset IRQs really don't have any masking ability - all we have is a
status register to allow us to decode the source, and a three input OR
gate inside a CPLD.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
GPIO27 is just connected to a CPLD input without any pull-ups or pull-
downs. If GPIO27 is left as an input, it will float around mid-supply,
which for CMOS inputs is the worst place for a pin to be. Ensure that
this pin is driven.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Avoid glitching the GPIO signals during initialization, which can
have undesirable effects. Ensure that the desired pin state is set
before we change the GPIO pin direction to be an output.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert StrongARM-11x0 platforms and core SoC code to use the
DEFINE_RES_xxx macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Neponset calls sa1110_mb_disable() from __devinit code, but
sa1110_mb_disable() is marked __init, and so causes a section
mismatch warning.
As sa1110_mb_enable() and sa1110_mb_disable() need to be callable
from suspend/resume paths as well, they must not be marked __init
or __devinit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Sometimes, we get stuck while trying to enter sleep. This seems
to occur if we do not have udelay() in the instruction cache. Avoid
this by requesting a short delay prior to modifying the SDRAM timings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Hackkit defined its flash memory resource to be 32M + 1 byte.
Jornada defined the Epson video controller resources to be one byte
larger than they should be, and mis-mapped the SA-1111 companion
chip one byte smaller than it should be.
Fix these.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There were conflicts between fixes going in after 3.3-rc1 and
Russell's stable arm-soc base branch. Resolving it in the dependency
branch so that each topic branch shares the same resolution.
Conflicts:
arch/arm/mach-at91/at91cap9.c
arch/arm/mach-at91/at91sam9g45.c
|
|
Rather than accessing GPSR and GPCR directly, use the GPIO subsystem
instead.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert Nanoengine socket driver to use the new irq/gpio management.
This is slightly more involved because we have to touch the private
platform header file to modify the GPIO bitmasks to be GPIO numbers.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Rather than accessing GPSR and GPCR directly, use the GPIO subsystem
instead.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert Cerf socket driver to use the new irq/gpio management.
This is slightly more involved because we have to touch the private
platform header file to modify the GPIO bitmasks to be GPIO numbers.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert Assabet socket driver to use the new irq/gpio management.
This is slightly more involved because we have to touch the private
platform header file to modify the GPIO bitmasks to be GPIO numbers.
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch taken from af9081ae64 (ARM: sa1100: Refactor mcp-sa11x0 to use
platform resources.) by Jochen Friedrich <jochen@scram.de>, and fixes
applied.
We can safely do this now that we have sanitized host removal; the
original patch had use-after-free bugs in the removal code. Not only
that, but there was no checking of the ioremap() return.
The final change over Jochen's patch is that we wrap the base pointer
selection inside the various register indexes, which reduces the
possibility of the wrong register index being used.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch taken from af9081ae64 (ARM: sa1100: Refactor mcp-sa11x0 to use
platform resources.) by Jochen Friedrich <jochen@scram.de>, and
consolidated to use a common function.
Move the setup of the PPC unit out of mcp-sa11x0 into the core SA11x0
code, and call it from each platforms initialization file. This
centralizes the setup of the PPC unit while not polluting the mcp-sa11x0
driver with these details.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
The Jornada SSP driver is supposed to be initialized by a
module_init() call, but it was missed at some merge point. Since
the driver mostly pass calls through it magically works anyway,
but needs to be rectified.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When this is the only content remaining in mach/system.h then the
whole file is removed.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-and-tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: David Brown <davidb@codeaurora.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
bus."
This reverts commit 5dd7bf59e0e8563265b3e5b33276099ef628fcc7.
Conflicts:
scripts/mod/file2alias.c
This change is wrong on many levels. First and foremost, it causes a
regression. On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:
ucb1x00 ID not found: 1005
0x1005 is a valid ID for the UCB1300 device.
Secondly, this patch is way over the top in terms of complexity. The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver. Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.
|
|
This reverts commit af9081ae64b941d32239b947882cd59ba855c5db.
This revert is necessary to revert 5dd7bf59e0e8563265b3e5b33276099ef628fcc7.
|
|
WARNING: arch/arm/mach-sa1100/built-in.o(.data+0x11b8): Section mismatch in reference from the variable sa1100_driver to the function .init.text:sa1100_cpu_init()
The variable sa1100_driver references
the function __init sa1100_cpu_init()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
f408c985cefc (GPIO: sa1100: implement proper gpiolib gpio_to_irq conversion)
made gpio_to_irq() a function. This breaks collie where it's used to
initialize some static data. Fix that by moving the initialization to
the init code.
arch/arm/mach-sa1100/collie.c:139: error: initializer element is not constant
arch/arm/mach-sa1100/collie.c:139: error: (near initialization for 'collie_power_resource[0].start')
arch/arm/mach-sa1100/collie.c:140: error: initializer element is not constant
arch/arm/mach-sa1100/collie.c:140: error: (near initialization for 'collie_power_resource[0].end')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This reverts commit 7cea00657dd4daef66ad95e976d5d67ed94cb97e.
The sa1100 cleanups fatally broke the SA1100 RTC driver - the first
hint that something is wrong are these compiler warnings:
drivers/rtc/rtc-sa1100.c:42:1: warning: "RCNR" redefined
In file included from arch/arm/mach-sa1100/include/mach/hardware.h:73,
from drivers/rtc/rtc-sa1100.c:35:
arch/arm/mach-sa1100/include/mach/SA-1100.h:877:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:43:1: warning: "RTAR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:876:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:44:1: warning: "RTSR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:879:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:45:1: warning: "RTTR" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:878:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:47:1: warning: "RTSR_HZE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:891:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:48:1: warning: "RTSR_ALE" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:890:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:49:1: warning: "RTSR_HZ" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:889:1: warning: this is the location of the previous definition
drivers/rtc/rtc-sa1100.c:50:1: warning: "RTSR_AL" redefined
arch/arm/mach-sa1100/include/mach/SA-1100.h:888:1: warning: this is the location of the previous definition
and the second problem, which is far more severe, are the different
register layouts, resulting in the wrong registers being read on
SA11x0 platforms. This patch adds:
#define RCNR 0x00 /* RTC Count Register */
#define RTAR 0x04 /* RTC Alarm Register */
#define RTSR 0x08 /* RTC Status Register */
#define RTTR 0x0c /* RTC Timer Trim Register */
but the SA11x0 registers are:
#define RTAR __REG(0x90010000) /* RTC Alarm Reg. */
#define RCNR __REG(0x90010004) /* RTC CouNt Reg. */
#define RTTR __REG(0x90010008) /* RTC Trim Reg. */
#define RTSR __REG(0x90010010) /* RTC Status Reg. */
|
|
This reverts commit edf3ff5bac2582b57de4e7c6569fee5d7c1c0a42.
This revert is necessary to revert the broken "RTC: sa1100:
support sa1100, pxa and mmp soc families" change.
|
|
git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm
* 'fixes' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-arm:
ARM: sa11x0: assabet: fix build warning
ARM: Add arm_memblock_steal() to allocate memory away from the kernel
ARM: 7275/1: LPAE: Check the CPU support for the long descriptor format
ARM: 7274/1: NUC900: Rename nuc900-audio platform device to nuc900-ac97
ARM: 7272/1: S3C24XX: Fix build error for missing <mach/system-reset.h>
ARM: 7271/1: Fix typo in conversion of ARCH_NR_GPIOS to Kconfig
|
|
Since a32618d2 (ARM: pgtable: switch to use pgtable-nopud.h), assabet
warns as follows:
arch/arm/mach-sa1100/assabet.c: In function 'map_sa1100_gpio_regs':
arch/arm/mach-sa1100/assabet.c:264: warning: passing argument 1 of 'pmd_offset' from incompatible pointer type
Fix this by adding the necessary pud_offset() macro.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
2nd round of GPIO changes for v3.3 merge window
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6:
GPIO: sa1100: implement proper gpiolib gpio_to_irq conversion
gpio: pl061: remove combined interrupt
gpio: pl061: convert to use generic irq chip
GPIO: add bindings for managed devices
ARM: realview: convert pl061 no irq to 0 instead of -1
gpio: pl061: convert to use 0 for no irq
gpio: pl061: use chained_irq_* functions in irq handler
GPIO/pl061: Add suspend resume capability
drivers/gpio/gpio-tegra.c: use devm_request_and_ioremap
|
|
The existing gpio_to_irq() implementation on sa1100 only translates
validly for internal GPIOs. Since this sub-arch enables GPIOLIB
support, this results in buggy translations for non-internal GPIOs.
Get rid of the private gpio_to_irq() implementation, replacing it
with the .to_irq method in the sa1100 gpio chip instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (80 commits)
x86/PCI: Expand the x86_msi_ops to have a restore MSIs.
PCI: Increase resource array mask bit size in pcim_iomap_regions()
PCI: DEVICE_COUNT_RESOURCE should be equal to PCI_NUM_RESOURCES
PCI: pci_ids: add device ids for STA2X11 device (aka ConneXT)
PNP: work around Dell 1536/1546 BIOS MMCONFIG bug that breaks USB
x86/PCI: amd: factor out MMCONFIG discovery
PCI: Enable ATS at the device state restore
PCI: msi: fix imbalanced refcount of msi irq sysfs objects
PCI: kconfig: English typo in pci/pcie/Kconfig
PCI/PM/Runtime: make PCI traces quieter
PCI: remove pci_create_bus()
xtensa/PCI: convert to pci_scan_root_bus() for correct root bus resources
x86/PCI: convert to pci_create_root_bus() and pci_scan_root_bus()
x86/PCI: use pci_scan_bus() instead of pci_scan_bus_parented()
x86/PCI: read Broadcom CNB20LE host bridge info before PCI scan
sparc32, leon/PCI: convert to pci_scan_root_bus() for correct root bus resources
sparc/PCI: convert to pci_create_root_bus()
sh/PCI: convert to pci_scan_root_bus() for correct root bus resources
powerpc/PCI: convert to pci_create_root_bus()
powerpc/PCI: split PHB part out of pcibios_map_io_space()
...
Fix up conflicts in drivers/pci/msi.c and include/linux/pci_regs.h due
to the same patches being applied in other branches.
|
|
Conflicts:
arch/arm/mach-mxs/include/mach/common.h
Pull in previous samsung conflict merges and do a trivial
merge of an mxs double-add conflict.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Make use of memory resources rather than hardcoded IO adresses.
This is a first step towards DT support.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
CC: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
Conflicts:
arch/arm/mach-exynos/cpu.c
The changes to arch/arm/mach-exynos/cpu.c were moved to
mach-exynos/common.c.
|
|
Conflicts:
arch/arm/kernel/setup.c
arch/arm/mach-shmobile/board-kota2.c
|
|
Fixed up a simple typo in the runtime sched_clock conversion
so we compile again.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Remove the now empty arch_reset() from all the mach/system.h includes,
and remove its callsite. Remove arm_machine_restart() as this function
no longer does anything useful.
For samsung platforms, remove the include of mach/system-reset.h and
plat/system-reset.h from their respective mach/system.h headers as these
just define their arch_reset functions. As a result, the s3c2410 and
plat-samsung system-reset.h files are no longer referenced, so remove
these files entirely.
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Hook these platforms restart code into the new restart hook rather
than using arch_reset().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Conflicts:
arch/arm/kernel/setup.c
|
|
Fixes this build error:
arch/arm/mach-sa1100/nanoengine.c:75:11: error: 'PAGE_SHIFT' undeclared here (not in a function)
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Since the regmap of rtc on sa1100, pxa and mmp Marvell soc families are
almost the same, so re-arch the rtc-sa1100 to support them.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
arm-eabi-4.4.3-ld:--defsym zreladdr=: syntax error
make[2]: *** [arch/arm/boot/compressed/vmlinux] Error 1
make[1]: *** [arch/arm/boot/compressed/vmlinux] Error 2
make: *** [uImage] Error 2
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
|
|
devel-stable
|
|
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
|
