| Age | Commit message (Collapse) | Author |
|---|
|
Pull arm fixes from Russell King:
"Not much here again.
The two most notable things here are the sched_clock() fix, which was
causing problems with the scheduling of threaded IRQs after a suspend
event, and the vfp fix, which afaik has only been seen on some older
OMAP boards. Nevertheless, both are fairly important fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7569/1: mm: uninitialized warning corrections
ARM: 7567/1: io: avoid GCC's offsettable addressing modes for halfword accesses
ARM: 7566/1: vfp: fix save and restore when running on pre-VFPv3 and CONFIG_VFPv3 set
ARM: 7565/1: sched: stop sched_clock() during suspend
|
|
The variables here are really not used uninitialized.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: warning: 'offset.un' may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull ARM fixes from Russell King:
"A random collection of various fixes, mainly from Arnd and a few other
people. Not thing really stands out here."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: drop experimental status for hotplug and Thumb2
ARM: 7560/1: SMP_TWD: use DIV_ROUND_CLOSEST() for periodic mode
ARM: 7559/1: smp: switch away from the idmap before updating init_mm.mm_count
ARM: 7556/1: perf: fix updated event period in response to PERF_EVENT_IOC_PERIOD
ARM: 7555/1: kexec: fix segment memory addresses check
ARM: warnings in arch/arm/include/asm/uaccess.h
ARM: binfmt_flat: unused variable 'persistent'
ARM: be really quiet when building with 'make -s'
ARM: pass -marm to gcc by default for both C and assembler
ARM: Xen: fix initial build problems
ARM: export default read_current_timer
ARM: Fix another build warning in arch/arm/mm/alignment.c
ARM: export set_irq_flags
ARM: kprobes: make more tests conditional
|
|
Commit e9da6e9905e639b0f842a244bc770b48ad0523e9 ("ARM: dma-mapping:
remove custom consistent dma region") removed the last users of the
field. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Fix build warning in __dma_alloc() as below:
arch/arm/mm/dma-mapping.c: In function '__dma_alloc':
arch/arm/mm/dma-mapping.c:653:29: warning: 'page' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into fixes
|
|
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Pull second set of ARM updates from Russell King:
"This is the second set of ARM updates for this merge window.
Contained within are changes to allow the kernel to boot in hypervisor
mode on CPUs supporting virtualization, and cache flushing support to
the point of inner sharable unification, which are used by the
suspend/resume code to avoid having to do a full cache flush.
Also included is one fix for VFP code identified by Michael Olbrich."
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: vfp: fix saving d16-d31 vfp registers on v6+ kernels
ARM: 7549/1: HYP: fix boot on some ARM1136 cores
ARM: 7542/1: mm: fix cache LoUIS API for xscale and feroceon
ARM: mm: update __v7_setup() to the new LoUIS cache maintenance API
ARM: kernel: update __cpu_disable to use cache LoUIS maintenance API
ARM: kernel: update cpu_suspend code to use cache LoUIS operations
ARM: mm: rename jump labels in v7_flush_dcache_all function
ARM: mm: implement LoUIS API for cache maintenance ops
ARM: virt: arch_timers: enable access to physical timers
ARM: virt: Add CONFIG_ARM_VIRT_EXT option
ARM: virt: Add boot-time diagnostics
ARM: virt: Update documentation for hyp mode entry support
ARM: zImage/virt: hyp mode entry support for the zImage loader
ARM: virt: allow the kernel to be entered in HYP mode
ARM: opcodes: add __ERET/__MSR_ELR_HYP instruction encoding
|
|
Conflicts:
arch/arm/kernel/smp.c
|
|
One such warning was recently fixed in a761cebf "ARM: Fix build warning
in arch/arm/mm/alignment.c" but only for the thumb2 case, this fixes
the other half.
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:327:15: error: 'offset.un' may be used uninitialized in this function
arch/arm/mm/alignment.c:748:21: note: 'offset.un' was declared here
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
.fault now can retry. The retry can break state machine of .fault. In
filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
try, since the page is in page cache now, ra->mmap_miss is decreased. And
these are done in one fault, so we can't detect random mmap file access.
Add a new flag to indicate .fault is tried once. In the second try, skip
ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
I only tested x86, didn't test other archs, but looks the change for other
archs is obvious, but who knows :)
Signed-off-by: Shaohua Li <shaohua.li@fusionio.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Implement an interval tree as a replacement for the VMA prio_tree. The
algorithms are similar to lib/interval_tree.c; however that code can't be
directly reused as the interval endpoints are not explicitly stored in the
VMA. So instead, the common algorithm is moved into a template and the
details (node type, how to get interval endpoints from the node, etc) are
filled in using the C preprocessor.
Once the interval tree functions are available, using them as a
replacement to the VMA prio tree is a relatively simple, mechanical job.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM updates from Russell King:
"This is the first chunk of ARM updates for this merge window.
Conflicts are expected in two files - asm/timex.h and
mach-integrator/integrator_cp.c. Nothing particularly stands out more
than anything else.
Most of the growth is down to the opcodes stuff from Dave Martin,
which is countered by Rob's patches to use more of the asm-generic
headers on ARM."
(A few more conflicts grew since then, but it all looked fairly trivial)
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (44 commits)
ARM: 7548/1: include linux/sched.h in syscall.h
ARM: 7541/1: Add ARM ERRATA 775420 workaround
ARM: ensure vm_struct has its phys_addr member filled in
ARM: 7540/1: kexec: Check segment memory addresses
ARM: 7539/1: kexec: scan for dtb magic in segments
ARM: 7538/1: delay: add registration mechanism for delay timer sources
ARM: 7536/1: smp: Formalize an IPI for wakeup
ARM: 7525/1: ptrace: use updated syscall number for syscall auditing
ARM: 7524/1: support syscall tracing
ARM: 7519/1: integrator: convert platform devices to Device Tree
ARM: 7518/1: integrator: convert AMBA devices to device tree
ARM: 7517/1: integrator: initial device tree support
ARM: 7516/1: plat-versatile: add DT support to FPGA IRQ
ARM: 7515/1: integrator: check PL010 base address from resource
ARM: 7514/1: integrator: call common init function from machine
ARM: 7522/1: arch_timers: register a time/cycle counter
ARM: 7523/1: arch_timers: enable the use of the virtual timer
ARM: 7531/1: mark kernelmode mem{cpy,set} non-experimental
ARM: 7520/1: Build dtb files in all target
ARM: Fix build warning in arch/arm/mm/alignment.c
...
|
|
'misc', 'opcodes' and 'syscall' into for-linus
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull CMA and DMA-mapping updates from Marek Szyprowski:
"This time the pull request is rather small, because the further
redesign patches were not ready on time.
This pull request consists of the patches which extend ARM DMA-mapping
subsystem with support for CPU coherent (ACP) DMA busses. The first
client of the new version is HighBank SATA driver. The second part of
the pull request includes various cleanup for both CMA common code and
ARM DMA-mapping subsystem."
Fix up trivial add-add conflict due to the "dma-coherent" DT property
being added next to the "calxeda,port-phys" property for the Calxeda
AHCI controller.
* 'for-v3.7' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: Remove unsed var at arm_coherent_iommu_unmap_page
ARM: highbank: add coherent DMA setup
ARM: kill off arch_is_coherent
ARM: add coherent iommu dma ops
ARM: add coherent dma ops
ARM: dma-mapping: Refrain noisy console message
ARM: dma-mapping: Small logical clean up
drivers: dma-contiguous: refactor dma_alloc_from_contiguous()
|
|
|
|
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
With ixp2xxx removed, there are no platforms that define arch_is_coherent,
so the last occurrences of arch_is_coherent can be removed. Any new
platform with coherent i/o should use coherent dma mapping functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Remove arch_is_coherent() from iommu dma ops and implement separate
coherent ops functions.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
arch_is_coherent is problematic as it is a global symbol. This
doesn't work for multi-platform kernels or platforms which can support
per device coherent DMA.
This adds arm_coherent_dma_ops to be used for devices which connected
coherently (i.e. to the ACP port on Cortex-A9 or A15). The arm_dma_ops
are modified at boot when arch_is_coherent is true.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
With many IOMMU'able devices, console gets noisy.
Tegra30 has a few dozen of IOMMU'able devices.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Skip unnecessary operations if order == 0. A little bit easier to
read.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Pull ARM soc device tree updates from Olof Johansson:
"Device tree conversion and enablement branch. Mostly a bunch of new
bindings and setup for various platforms, but the Via/Winchip VT8500
platform is also converted over from being 100% legacy to now use
device tree for probing. More of that will come for 3.8."
Trivial conflicts due to removal of vt8500 files, and one documentation
file that was added with slightly different contents both here and in
the USb tree.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (212 commits)
arm: vt8500: Fixup for missing gpio.h
ARM: LPC32xx: LED fix in PHY3250 DTS file
ARM: dt: mmp-dma: add binding file
arm: vt8500: Update arch-vt8500 to devicetree support.
arm: vt8500: gpio: Devicetree support for arch-vt8500
arm: vt8500: doc: Add device tree bindings for arch-vt8500 devices
arm: vt8500: clk: Add Common Clock Framework support
video: vt8500: Add devicetree support for vt8500-fb and wm8505-fb
serial: vt8500: Add devicetree support for vt8500-serial
rtc: vt8500: Add devicetree support for vt8500-rtc
arm: vt8500: Add device tree files for VIA/Wondermedia SoC's
ARM: tegra: Add Avionic Design Tamonten Evaluation Carrier support
ARM: tegra: Add Avionic Design Medcom-Wide support
ARM: tegra: Add Avionic Design Plutux support
ARM: tegra: Add Avionic Design Tamonten support
ARM: tegra: dts: Add pwm label
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
...
|
|
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM soc bug fixes from Olof Johansson:
"These were submitted as bug fixes before v3.6 but not considered
important enough to be included in it. Some of them cross over to
cleanup territory as well, and aren't strictly bugfixes."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
ARM: nomadik: remove NAND_NO_READRDY use
ARM: pxa: fix return value check in pxa2xx_drv_pcmcia_probe()
ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
ARM: S3C24XX: removes unnecessary semicolon
ARM: S3C24xx: delete double assignment
ARM: EXYNOS: fix address for EXYNOS4 MDMA1
ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
ARM: ep93xx: Move ts72xx.h out of include/mach
ARM: ep93xx: use __iomem pointers for MMIO
ARM: msm: Fix early debug uart mapping on some memory configs
ARM: msm: io: Change the default static iomappings to be shared
ARM: msm: io: Remove 7x30 iomap region from 7x00
ARM: msm: Remove call to missing FPGA init on 8660
ARM: OMAP4: wakeupgen: remove duplicate AUXCOREBOOT* read/write
ARM: OMAP4: wakeupgen: Fix the typo in AUXCOREBOOT register save
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into devel-stable
|
|
arm: Add ARM ERRATA 775420 workaround
Workaround for the 775420 Cortex-A9 (r2p2, r2p6,r2p8,r2p10,r3p0) erratum.
In case a date cache maintenance operation aborts with MMU exception, it
might cause the processor to deadlock. This workaround puts DSB before
executing ISB if an abort may occur on cache maintenance.
Based on work by Kouei Abe and feedback from Catalin Marinas.
Signed-off-by: Kouei Abe <kouei.abe.cp@rms.renesas.com>
[ horms@verge.net.au: Changed to implementation
suggested by catalin.marinas@arm.com ]
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Some architectures like xscale and feroceon have cache API variants that
map cache flushing functions as aliases to the base architecture.
This patch adds the required aliases to complete the implementation of
cache flushing LoUIS API.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This allows /proc/vmallocinfo to show the physical address for
ioremap mappings.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The ARMv7 processor setup function __v7_setup() cleans and invalidates the
CPU cache before enabling MMU to start the CPU with a clean CPU local cache.
But on ARMv7 architectures like Cortex-[A15/A8], this code will end
up flushing the L2 caches(up to level of Coherency) which is undesirable
and expensive. The setup functions are used in the CPU hotplug scenario too
and hence flushing all cache levels should be avoided.
This patch replaces the cache flushing call with the newly introduced
v7 dcache LoUIS API where only cache levels up to LoUIS are cleaned and
invalidated when a processors executes __v7_setup which is the expected
behavior.
For processors like A9 and A5 where the L2 cache is an outer one the
behavior should be unchanged.
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
|
|
This patch renames jump labels in v7_flush_dcache_all in order to define
a specific flush cache levels entry point.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
|
|
ARM v7 architecture introduced the concept of cache levels and related
control registers. New processors like A7 and A15 embed an L2 unified cache
controller that becomes part of the cache level hierarchy. Some operations in
the kernel like cpu_suspend and __cpu_disable do not require a flush of the
entire cache hierarchy to DRAM but just the cache levels belonging to the
Level of Unification Inner Shareable (LoUIS), which in most of ARM v7 systems
correspond to L1.
The current cache flushing API used in cpu_suspend and __cpu_disable,
flush_cache_all(), ends up flushing the whole cache hierarchy since for
v7 it cleans and invalidates all cache levels up to Level of Coherency
(LoC) which cripples system performance when used in hot paths like hotplug
and cpuidle.
Therefore a new kernel cache maintenance API must be added to cope with
latest ARM system requirements.
This patch adds flush_cache_louis() to the ARM kernel cache maintenance API.
This function cleans and invalidates all data cache levels up to the
Level of Unification Inner Shareable (LoUIS) and invalidates the instruction
cache for processors that support it (> v7).
This patch also creates an alias of the cache LoUIS function to flush_kern_all
for all processor versions prior to v7, so that the current cache flushing
behaviour is unchanged for those processors.
v7 cache maintenance code implements a cache LoUIS function that cleans and
invalidates the D-cache up to LoUIS and invalidates the I-cache, according
to the new API.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
|
|
When either of __alloc_from_contiguous or __alloc_remap_buffer fails
to provide a valid pointer, allocated memory is freed up and an error
is returned. 'pages' was however not freed before returning error.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
git://git.linaro.org/people/ljones/linux-3.0-ux500 into next/dt
* 'for-arm-soc-next' of git://git.linaro.org/people/ljones/linux-3.0-ux500:
ARM: ux500: Fix SSP register address format
ARM: ux500: Apply tc3589x's GPIO/IRQ properties to HREF's DT
ARM: ux500: Remove redundant #gpio-cell properties from Snowball DT
ARM: ux500: Add all encompassing sound node to the HREF Device Tree
ARM: ux500: Add nodes for the MSP into the HREF Device Tree
ARM: ux500: Add all known I2C sub-device nodes to the HREF DT
ARM: ux500: Stop registering I2C sub-devices for HREF when DT is enabled
ARM: ux500: Stop registering Audio devices for HREF when DT is enabled
ARM: ux500: Add all encompassing sound node to the Snowball Device Tree
ARM: ux500: Add nodes for the MSP into Device Tree
ARM: ux500: Rename MSP board file to something more meaningful
ARM: ux500: Remove platform registration of MSP devices
ARM: ux500: Stop registering the MOP500 Audio driver from platform code
ARM: ux500: Pass MSP DMA platform data though AUXDATA
ARM: ux500: Fork MSP platform registration for step-by-step DT enablement
ARM: ux500: Add AB8500 CODEC node to DB8500 Device Tree
ARM: ux500: Clean-up MSP platform code
ARM: ux500: Pass SDI DMA information though AUX_DATA to MMCI
ARM: ux500: Add UART support to the HREF Device Tree
ARM: ux500: Add skeleton Device Tree for the HREF reference board
...
+ sync to v3.6-rc6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/fixes-non-critical
A few non-critical fixes/cleanups for samsung platforms.
* 'v3.7-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Add missing variable declaration in s3c64xx_spi1_set_platdata()
ARM: S3C24XX: removes unnecessary semicolon
ARM: S3C24xx: delete double assignment
ARM: EXYNOS: fix address for EXYNOS4 MDMA1
ARM: EXYNOS: fixed SYSMMU setup definition to mate parameter name
+ sync to 3.6-rc6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree related changes for omaps.
Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.
* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm/dts: Mux uart pins for omap4-sdp
ARM: OMAP2+: select PINCTRL in Kconfig
arm/dts: Add pinctrl driver entries for omap2/3/4
arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
ARM: dts: omap3-overo: Add support for the blue LED
Documentation: dt: Update the OMAP documentation with Overo/Toby
ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
ARM: dts: OMAP4: Add reg and interrupts for every nodes
ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
ARM: dts: AM33XX: Convert all hex numbers to lower-case
ARM: dts: omap3-beagle: Enable audio support
ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
ARM: dts: omap5: Add McBSP entries
ARM: dts: omap4: Add reg-names for McPDM and DMIC
ARM: dts: omap4: Add McBSP entries
ARM: dts: omap3: Add McBSP entries
ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
...
|
|
It is now possible to enable the virtualization extention support.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
* tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: remove plat/board.h file
ARM: OMAP: move debug_card_init() function
ARM: OMAP1: move lcd pdata out of arch/arm/*
ARM: OMAP1: move omap1_bl pdata out of arch/arm/*
ARM: OMAP: remove the omap custom tags
ARM: OMAP1: remove the crystal type tag parsing
ARM: OMAP: remove the sti console workaround
ARM: OMAP: omap3evm: cleanup revision bits
ARM: OMAP: cleanup struct omap_board_config_kernel
+ sync to 3.6-rc5
|
|
Fix this harmless build warning:
arch/arm/mm/alignment.c: In function 'do_alignment':
arch/arm/mm/alignment.c:749:21: warning: 'offset.un' may be used uninitialized in this function
This is caused by the compiler not being able to properly analyse the
code to prove that offset.un is assigned in every case. The case it
struggles with is where we assign the handler from the Thumb parser -
do_alignment_t32_to_handler(). As this starts by zeroing this variable
via a pointer, move it into the calling function. This fixes the
warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
There is a bug if l2x0 controller has been enabled when calling
l2x0_init, the aux ctrl register will not be saved in l2x0_saved_regs.
Therefore we will use uninitialized l2x0_saved_regs.aux_ctrl for
resuming later.
In this patch, the aux ctrl value is read and saved after it is
initialized. So we have the real value being set for resuming.
Link: http://lkml.kernel.org/r/1336046857-24133-1-git-send-email-ylmao@marvell.com
Signed-off-by: Yilu Mao <ylmao@marvell.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull one more DMA-mapping fix from Marek Szyprowski:
"This patch fixes very subtle bug (typical off-by-one error) which
might appear in very rare circumstances."
* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: mm: fix DMA pool affiliation check
|
|
next/fixes-non-critical
From "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad72 now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull ARM fixes from Russell King:
"It's been a while... so there's a little more here than normal.
Mostly updates from Will for the breakpoint stuff, and plugging a few
holes in the user access functions which crept in when domain support
was disabled for ARMv7 CPUs."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7529/1: delay: set loops_per_jiffy when moving to timer-based loop
ARM: 7528/1: uaccess: annotate [__]{get,put}_user functions with might_fault()
ARM: 7527/1: uaccess: explicitly check __user pointer when !CPU_USE_DOMAINS
ARM: 7526/1: traps: send SIGILL if get_user fails on undef handling path
ARM: 7521/1: Fix semihosting Kconfig text
ARM: 7513/1: Make sure dtc is built before running it
ARM: 7512/1: Fix XIP build due to PHYS_OFFSET definition moving
ARM: 7499/1: mm: Fix vmalloc overlap check for !HIGHMEM
ARM: 7503/1: mm: only flush both pmd entries for classic MMU
ARM: 7502/1: contextidr: avoid using bfi instruction during notifier
ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores
ARM: 7497/1: hw_breakpoint: allow single-byte watchpoints on all addresses
ARM: 7496/1: hw_breakpoint: don't rely on dfsr to show watchpoint access type
ARM: Fix ioremap() of address zero
|
|
This prepares *of_device_id.data becoming const. Without this change the
following warning would occur:
arch/arm/mm/cache-l2x0.c: In function 'l2x0_of_init':
arch/arm/mm/cache-l2x0.c:573:7: warning: assignment discards 'const' qualifier from pointer target type [enabled by default]
though.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
The __free_from_pool() function was changed in
e9da6e9905e639b0f842a244bc770b48ad0523e9. Unfortunately, the test that
checks whether the provided (start,size) is within the DMA pool has
been improperly modified. It used to be:
if (start < coherent_head.vm_start || end > coherent_head.vm_end)
Where coherent_head.vm_end was non-inclusive (i.e, it did not include
the first byte after the pool). The test has been changed to:
if (start < pool->vaddr || start > pool->vaddr + pool->size)
So now pool->vaddr + pool->size is inclusive (i.e, it includes the
first byte after the pool), so the test should be >= instead of >.
This bug causes the following message when freeing the *first* DMA
coherent buffer that has been allocated, because its virtual address
is exactly equal to pool->vaddr + pool->size :
WARNING: at /home/thomas/projets/linux-2.6/arch/arm/mm/dma-mapping.c:463 __free_from_pool+0xa4/0xc0()
freeing wrong coherent size from pool
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Maen Suleiman <maen@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Shadi Ammouri <shadi@marvell.com>
Cc: Eran Ben-Avi <benavi@marvell.com>
Cc: Yehuda Yitschak <yehuday@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
[m.szyprowski: rebased onto v3.6-rc5 and resolved conflict]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
* 'soc-core' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: mach-shmobile: Add compilation support for dtbs using 'make dtbs'
+ sync to 3.6-rc3
|
|
As Stephen Rothwell reports, a849088aa155 ("ARM: Fix ioremap() of
address zero") from the arm-current tree and commit c2794437091a ("ARM:
Add fixed PCI i/o mapping") from the arm-soc tree conflict in
a nontrivial way in arch/arm/mm/mmu.c.
Rob Herring explains:
The PCI i/o reserved area has a dummy physical address of 0 and
needs to be skipped by ioremap searches. So we don't set
VM_ARM_STATIC_MAPPING to prevent matches by ioremap. The vm_struct
settings don't really matter when we do the real mapping of the
i/o space.
Since commit a849088aa155 is at the start of the fixes branch
in the arm tree, we can merge it into the branch that contains
the other ioremap changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Make use of the same atomic pool as DMA does, and skip a kernel page
mapping which can involve sleep'able operations at allocating a kernel
page table.
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Support atomic allocation in __iommu_get_pages().
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
[moved __atomic_get_pages() under #ifdef CONFIG_ARM_DMA_USE_IOMMU
to avoid unused fuction warning for no-IOMMU case]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
