| Age | Commit message (Collapse) | Author |
|---|
|
Implement pci_load_of_ranges on MIPS. Due to lack of test hardware only 32bit
bus width is supported. This function is based on pci_process_bridge_OF_ranges
from powerpc.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Everybody uses the generic pcibios_resource_to_bus() supplied by the core
now, so remove the ARCH_HAS_GENERIC_PCI_OFFSETS used during conversion.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
Here's the wrinkle on Cobalt: we can't generate normal I/O port addresses
on PCI because the GT-64111 doesn't do any address translation, so we have
this:
CPU I/O port addresses [io 0x0000-0xffffff]
PCI bus I/O port addresses [io 0x10000000-0x10ffffff]
Legacy-mode IDE controllers start out with the legacy bus addresses, e.g.,
0x1f0, assigned by pci_setup_device(). These are outside the range of
addresses GT-64111 can generate on PCI, but pcibios_fixup_device_resources()
converted them to CPU addresses anyway by adding io_offset. Therefore, we
had to pre-adjust them in cobalt_legacy_ide_fixup().
With io_offset = 0xf0000000, we had this:
res->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x100001f0 -= io_offset in cobalt_legacy_ide_fixup()
res->start = 0x1f0 += io_offset in pcibios_fixup_device_resources()
The difference after this patch is that the generic pci_bus_to_resource()
only adds the offset if the bus address is inside a host bridge window.
Since 0x1f0 is not a valid bus address and is not inside any windows, it is
unaffected, so we now have this:
region->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x1f0 no offset by pci_bus_to_resource()
That means we can remove both pcibios_fixup_device_resources() and
cobalt_legacy_ide_fixup().
I would *rather* set the host bridge offset to zero (which corresponds
to what the GT-64111 actually does), and have both CPU and PCI addresses
of [io 0x10000000-0x10ffffff]. However, that would require changes to
generic code that assumes legacy I/O addresses, such as pic1_io_resource
([io 0x0020-0x00021]), and we'd have to keep a Cobalt IDE fixup.
Of course, none of this changes the fact that references to I/O port
0x1f0 actually go to port 0x100001f0, not 0x1f0, on the Cobalt PCI bus.
Fortunately the VT82C586 IDE controller only decodes the low 24 address
bits, so it does work.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves mips to the pci_flags approach so
generic code can use the same test across all architectures.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
MSI-X interrupts are not supported yet for Octeon, return error if
MSI-X interrupts are requested by driver so that the driver will fall
back to use MSI interrupts.
Signed-off-by: Chandrakala Chavva <cchavva@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/1506/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
|
|
All the architectures properly set NEED_DMA_MAP_STATE now so we can safely
add linux/pci-dma.h to linux/pci.h and remove the linux/pci-dma.h
inclusion in arch's asm/pci.h
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This was #define'd as 0 on all platforms, so let's get rid of it.
This change makes pci_scan_slot() slightly easier to read.
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Tony Luck <tony.luck@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This function was only used by pci_claim_resource(), and the last commit
deleted that use.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented. This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.
Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
