| Age | Commit message (Collapse) | Author |
|---|
|
Register a clock device for the SPI block of the
MT7620 SoC. The clock device will be used by the
SPI host controller driver to determine the base
clock of the controller.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5754/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The watchdog driver of the SoC uses the clk API to
get the clock associated with the watchdog device.
However the MT7620 specific setup code does not
register a clock for the watchdog device yet which
leads to the following error:
rt2880_wdt: probe of 10000120.watchdog failed with error -2
Register a clock device for the watchdog in order to
avoid the error and make the watchdog usable.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5756/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The current code assumes that the peripheral clock always
runs at 40MHz which is not true in all configuration. The
peripheral clock can also use the reference clock instead
of the fixed 40MHz rate. If the reference clock runs at a
different rate, various peripheries are behaving incorrectly.
Additionally, the currectly calculated system clock is also
wrong. The actual value what the code computes is the rate
of the DRAM which can be different from the system clock.
Add new helper functions to get the rate of the different
clocks and use the correct values for the registered clock
devices.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5755/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Select the the EHCI and OHCI symbols.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5675/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Make the code print which of SDRAM, DDR1 or DDR2 was detected.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/5671/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Make plat_time_init() call clocksource_of_init() allowing the systick cevt
to load.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/5670/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Newer Ralink SoC (MT7620x and RT5350) have a 50KHz clock that runs independent
of the SoC master clock. If we want to automatic frequency scaling to work we
need to use the systick timer as the clock source.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5669/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Adds a driver for the periodic timer found on Ralink SoC.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5682/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
same story as with oprofilefs_mkdir()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
it's always equal to ->d_sb of the second argument (parent dentry),
due to either being literally that, or ->d_sb of parent's parent.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
PCI device hotplug:
- Use PCIe native hotplug, not ACPI hotplug, when possible (Neil Horman)
- Assign resources on per-host bridge basis (Yinghai Lu)
MPS (Max Payload Size):
- Allow larger MPS settings below hotplug-capable Root Port (Yijing Wang)
- Add warnings about unsafe MPS settings (Yijing Wang)
- Simplify interface and messages (Bjorn Helgaas)
SR-IOV:
- Return -ENOSYS on non-SR-IOV devices (Stefan Assmann)
- Update NumVFs register when disabling SR-IOV (Yijing Wang)
Virtualization:
- Add bus and slot reset support (Alex Williamson)
- Fix ACS (Access Control Services) issues (Alex Williamson)
Miscellaneous:
- Simplify PCIe Capability accessors (Bjorn Helgaas)
- Add pcibios_pm_ops for arch-specific hibernate stuff (Sebastian Ott)
- Disable decoding during BAR sizing only when necessary (Zoltan Kiss)
- Delay enabling bridges until they're needed (Yinghai Lu)
- Split Designware support into Synopsys and Exynos parts (Jingoo Han)
- Convert class code to use dev_groups (Greg Kroah-Hartman)
- Cleanup Designware and Exynos I/O access wrappers (Seungwon Jeon)
- Fix bridge I/O window alignment (Bjorn Helgaas)
- Add pci_wait_for_pending_transaction() (Casey Leedom)
- Use devm_ioremap_resource() in Marvell driver (Tushar Behera)
* tag 'pci-v3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (63 commits)
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
...
|
|
Add a default built-in device tree for XLP2xx SoC. The new file
xlp_fvp.dts has updated entries for I2C and memory.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5705/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add USB intialization code to handle the new XLP2XX USB 3.0 block.
This adds xlp/usb-init-xlp2.c to initialize the XLP2XX USB glue-logic
for XHCI and EHCI. Interrupt and IO offset code in xlp-hal/iomap.h
and xlp/nlm_hal.c is also updated for the new USB block.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5744/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
XLP2xx has a new I2C controller which has 4 buses connected to
it. Update the IO offset and IRQ mapping code to reflect this.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5707/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
On XLP2xx, wakeup code does not need to enable clock on the core.
Update xlp/wakeup.c to handle this.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5703/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add code to calculate the CPU and PIC frequency for XLP2XX SoCs.
Since the PIC frequency on XLP2XX can be configured, add a new macro
pic_timer_freq() to be used in netlogic/common/time.c.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/5701/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The config7/config4 register has to be written on all the threads.
This does not cause any problems in XLP, but is needed for XLPII
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5700/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
XLP2XX is first in the series of 28nm XLPII processors.
The changes are to:
* Add processor ID for XLP2XX to asm/cpu.h and kernel/cpu-probe.c.
* Add a cpu_is_xlpii() function to check for XLPII processors.
* Update xlp_mmu_init() to use config4 to enable extended TLB.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The flash chipselects can span 32MB, fix this in the built-in device
tree.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Do not pass a memory section in the built-in DTB, and let the
boot code use the values from the DRAM BARs.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Read the memory from the Bridge DRAM BARs, if it is not passed in
from the device tree. This will allow us to remove memory configuration
from built in device trees.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5743/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The ath79 code uses static clock devices and
provides its own clk_{get,put} implementations.
Change the code to use dynamically allocated
clock devices and register the clocks within
the clkdev framework.
Additionally, remove the local clk_{get,put}
implementation. The clkdev framework has a
common implementation of those.
Also move the call of ath79_clock_init() from
plat_mem_init() to plat_time_init(). Otherwise
it would not be possible to use memory allocation
functions from ath79clock_init() becasuse the
memory subsystem is not yet initialized when
plat_mem_init() runs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5780/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Use local variables for ref, cpu, ddr and ahb
rates in SoC specific clock init functions.
The patch has no functional changes, it is
an interim change in preparation of the next
patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5781/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Instead of accessing the rate field of the static
clock devices directly, use the recently introduced
helper function to get the rate of the basic clocks.
The static ath79_{ahb,cpu,ddr,ref}_clk variables
will be removed by a subsequent patch. The actual
change is in preparation of that.
Also move the clock frequency printing code into
the plat_time_init function. We are getting the
cpu clock rate there already so we can save an
extra call of the helper.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5782/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The ath79 platform uses similar code to get the
rate of various clocks during init. Separate the
similar code into a new helper function and use
that to avoid code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5778/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The reference clock rate is passed in the first
argument of the function. Use that instead of the
rate of the global ath79_ref_clk variable.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5779/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The watchdog device on the AR933x is connected to
the AHB clock, however the current code uses the
reference clock. Due to the wrong rate, the watchdog
driver can't calculate correct register values for
a given timeout value and the watchdog unexpectedly
restarts the system.
The code uses the wrong value since the initial
commit 04225e1d227c8e68d685936ecf42ac175fec0e54
(MIPS: ath79: add AR933X specific clock init)
The patch fixes the code to use the correct clock
rate to avoid the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5777/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The ath79 code supports various SoCs which are using either a 24Kc
or a 74Kc core. The 74Kc core has DSP support, so don't hardwire
the values to zero.
Commit 00dc5ce2a653a332190aa29b2e1f3bceaa7d5b8d (MIPS: ath79: don't
hardcode the unavailability of the DSP ASE) has fixed this already,
but that change got reverted by 475032564ed96c94c085e3e7a90e07d150a7cec9
(MIPS: Hardwire detection of DSP ASE Rev 2 for systems, as required.)
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5750/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This add a default config for the Lantiq XWAY SoC.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5796/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The clocks of the serial ports were not setup properly.
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add cpu-feature-override.h for the GPON SoC
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5658/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This driver so far only reads the core voltage.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5677/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver pull request for 3.12-rc1.
Lots of n_tty reworks to resolve some very long-standing issues,
removing the 3-4 different locks that were taken for every character.
This code has been beaten on for a long time in linux-next with no
reported regressions.
Other than that, a range of serial and tty driver updates and
revisions. Full details in the shortlog"
* tag 'tty-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (226 commits)
hvc_xen: Remove unnecessary __GFP_ZERO from kzalloc
serial: imx: initialize the local variable
tty: ar933x_uart: add device tree support and binding documentation
tty: ar933x_uart: allow to build the driver as a module
ARM: dts: msm: Update uartdm compatible strings
devicetree: serial: Document msm_serial bindings
serial: unify serial bindings into a single dir
serial: fsl-imx-uart: Cleanup duplicate device tree binding
tty: ar933x_uart: use config_enabled() macro to clean up ifdefs
tty: ar933x_uart: remove superfluous assignment of ar933x_uart_driver.nr
tty: ar933x_uart: use the clk API to get the uart clock
tty: serial: cpm_uart: Adding proper request of GPIO used by cpm_uart driver
serial: sirf: fix the amount of serial ports
serial: sirf: define macro for some magic numbers of USP
serial: icom: move array overflow checks earlier
TTY: amiserial, remove unnecessary platform_set_drvdata()
serial: st-asc: remove unnecessary platform_set_drvdata()
msm_serial: Send more than 1 character on the console w/ UARTDM
msm_serial: Add support for non-GSBI UARTDM devices
msm_serial: Switch clock consumer strings and simplify code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add a uImage build target for MIPS, which builds uImage.gz (a U-Boot
image of vmlinux.bin.gz), and then symlinks it to uImage. This allows
for the use of other compression algorithms in future, and is how a few
other architectures do it.
It's enabled conditionally on load-y >= 0xffffffff80000000 which
hopefully allows 64bit kernels to also work as long as the load and
entry address can be represented by the 32bit addresses in the U-Boot
image format.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5795/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The vmlinux load address and entry address is calculated in multiple
places:
- arch/mips/Makefile defines load-y from CONFIG_PHYSICAL_START (or
defined by the platform) and passes it to
arch/mips/boot/compressed/Makefile.
- arch/mips/boot/compressed/Makefile calculates kernel entry using nm.
- arch/mips/lasat/image/Makefile calculates both load and entry address
using nm.
Lets combine these in the main Makefile and then pass them as Make
parameters to each of the three boot image Makefiles (in boot/,
boot/compressed, lasat/image/). The boot/ Makefile doesn't currently use
them, but will soon need to for U-Boot image targets.
The existing load-y definition is used in preference to calculating the
load address using nm.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5794/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Split out the arch/mips/boot/ and arch/mips/boot/compressed/ targets
into boot-y and bootz-y variables. This makes it slightly cleaner to add
new targets.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5793/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add symlink to include/dt-bindings from arch/mips/boot/dts/include/ to
match the ones in ARM and Meta architectures so that preprocessed device
tree files can include various useful constant definitions.
See commit c58299a (kbuild: create an "include chroot" for DT bindings)
merged in v3.10-rc1 for details.
MIPS structures it's dts files a little differently to other
architectures, having a separate dts directory for each SoC/platform,
but most of the definitions in the dt-bindings/ directory are common so
for now lets just have a single "include chroot" for all MIPS platforms.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Steven. J. Hill <steven.hill@imgtec.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kbuild@vger.kernel.org
Acked-by: Stephen Warren <swarren@nvidia.com>
Patchwork: http://patchwork.linux-mips.org/patch/5745/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The kbldr.h header file required for this was neither committed in the
original submission in a3a0f8c8ed2e2470f4dcd6da95020d41fed84747
"MIPS: PowerTV: Base files for Cisco PowerTV platform"
nor was it ever present in the git tree so this option never worked.
Fixes the following build problem:
arch/mips/powertv/reset.c:25:36: fatal error: asm/mach-powertv/kbldr.h: No such
file or directory
compilation terminated.
Cc: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: David VomLehn <dvomlehn@cisco.com>
Patchwork: https://patchwork.linux-mips.org/patch/5801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The NR_CPUS_DEFAULT_1 introduced as an aid for the QEMU
platform in 72ede9b18967e7a8a62a88f164f003193f6d891f
"[MIPS] Qemu: Fix Symmetric Uniprocessor support"
which was later removed in
302922e5f6901eb6f29c58539631f71b3d9746b8
"[MIPS] Qemu: Remove platform."
On certain randconfigs it may happen for NR_CPUS to have an
empty value because not all SMP platforms select a suitable
NR_CPUS_DEFAULT_* value. We fix this by restoring the range
of NR_CPUS to 2..64 and drop the NR_CPUS_DEFAULT_{1,2} symbols.
The first one is no longer used and the latter is not needed since
NR_CPUS=2 is now the default value.
Fixes the following problem on a randconfig:
.config:164:warning: symbol value '' invalid for NR_CPUS
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5747/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The jmr3927_vec txx9_board_vec struct is defined in
txx9/jmr3927/setup.c which is only built if
CONFIG_TOSHIBA_JMR3927 is selected. This patch fixes the following
build problem:
arch/mips/txx9/generic/setup.c: In function 'select_board':
arch/mips/txx9/generic/setup.c:354:20: error:
'jmr3927_vec' undeclared (first use in this function)
arch/mips/txx9/generic/setup.c:354:20: note: each undeclared
identifier is reported only once for each function it appears in
make[3]: *** [arch/mips/txx9/generic/setup.o] Error 1
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5713/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The pci.c code depends on symbols which are only visible
if CONFIG_PCI is selected.
Also fixes the following problem on loongson allnoconfig:
arch/mips/built-in.o: In function `pcibios_init':
pci.c:(.init.text+0x528):
undefined reference to `register_pci_controller'
arch/mips/built-in.o:(.data+0xc):
undefined reference to `loongson_pci_ops'
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5584/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Dynamic function tracing was not working on MIPS. When doing dynamic
tracing, the tracer attempts to match up the passed in address with
the one the compiler creates in the mcount tables. The MIPS code was
passing in the return address from the tracing function call, but the
compiler tables were the address of the function call. So they
wouldn't match.
Just subtracting 8 from the return address will give the address of
the function call. Easy enough.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
[david.daney@cavium.com: Adjusted code comment and patch Subject.]
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5592/
|
|
This is a fix for a bug introduced with commit
447cdf2628b59aa513a42785450b348dced26d8a, submitted as archived here:
http://www.linux-mips.org/cgi-bin/mesg.cgi?a=linux-mips&i=20080312235002.c717dde3.yoichi_yuasa%40tripeaks.co.jp
regrettably with no further explanation.
The issue is with the CP0 Count register read erratum present on R4000 and
some R4400 processors. If this erratum is present, then a read from this
register that happens around the time it reaches the value stored in the
CP0 Compare register causes a CP0 timer interrupt that is supposed to
happen when the values in the two registers match to be missed. The
implication for the chips affected is the CP0 timer can be used either as
a source of a timer interrupt (a clock event) or as a source of a
high-resolution counter (a clock source), but not both at a time.
The erratum does not affect timer interrupt operation itself, because in
this case the CP0 Count register is only read while the timer interrupt
has already been raised, while high-resolution counter references happen
at random times.
Additionally some systems apparently have issues with the timer interrupt
line being routed externally and not following the usual CP0 Count/Compare
semantics. In this case we don't want to use the R4k clock event.
We've meant to address the erratum and the timer interrupt routing issue
in time_init, however the commit referred to above broke our solution.
What we currently have is we enable the R4k clock source if the R4k clock
event initialization has succeeded (the timer is present and has no timer
interrupt routing issue) or there is no CP0 Count register read erratum.
Which gives the following boolean matrix:
clock event | count erratum => clock source
------------+---------------+--------------
0 | 0 | 1 (OK)
0 | 1 | 0 (bug!) -> no interference, could use
1 | 0 | 1 (OK)
1 | 1 | 1 (bug!) -> can't use, interference
What we want instead is to enable the R4k clock source if there is no CP0
Count register read erratum (obviously) or the R4k clock event
initialization has *failed* -- because in the latter case we won't be
using the timer interrupt anyway, so we don't care about any interference
CP0 Count reads might cause with the interrupt. This corresponds to the
following boolean matrix:
clock event | count erratum => clock source
------------+---------------+--------------
0 | 0 | 1
0 | 1 | 1
1 | 0 | 1
1 | 1 | 0
This is implemented here, effectively reverting the problematic commit,
and a short explanation is given next to code modified so that the
rationale is known to future readers and confusion is prevented from
happening here again.
It is worth noting that mips_clockevent_init returns 0 upon success while
cpu_has_mfc0_count_bug returns 0 upon failure. This is because the former
function returns an error code while the latter returns a boolean value.
To signify the difference I have therefore chosen to compare the result of
the former call explicitly against 0.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5799/
|
|
Linux 3.11-rc7
|
|
Some toolchains (including Cavium OCTEON SDK) are emitting .eh_frame
sections by default. Discard them as they are useless in the kernel.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
... and create asm/mach-cavium-octeon/gpio.h so that things continue
to build.
This allows us to use the existing I2C connected GPIO expanders.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/5632/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
There were many cases of:
return something;
break;
All those break statements are unreachable and thus redundant.
Signed-off-by: David Daney <david.daney@cavium.com>
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5727/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
