| Age | Commit message (Collapse) | Author |
|---|
|
During converting per-cpu ticker to genirq layer some
IRQ initialization code was removed by commit
2cf9530420e446bb61f665d02afeb81070106900 ("sparc32,leon:
per-cpu ticker use genirq per-cpu handler").
This patch reintroduces the code at the same place it was
removed from. IRQ12 - IRQ14 will crash on LEON SMP without
this patch because it will run the SUN4M IRQ trap handler.
Reported-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DMA region must be accessible in order for PCI peripheral
drivers to work, the sparc32 has DMA in the normal memory
zone which requires the GRPCI2 to PCI target BARs so that all
kernel low mem (192MB) can be mapped 1:1 to PCI address
space. The GRPCI2 has resizeable target BARs, by default the
first is made 256MB and all other BARs are disabled.
I/O space are always located on 0x1000-0x10000, but accessed
through the GRPCI2 PCI I/O Window memory mapped to virtual
address space.
Configuration space is accessed through the 64KB GRPCI2 PCI
CFG Window using LDA bypassing the MMU.
The GRPCI2 has a single PCI Window for prefetchable and non-
prefetchable address space, it is up to the AHB master
requesting PCI data to determine access type. Memory space
is mapped 1:1.
The GRPCI2 core can be configured in 4 different IRQ modes,
where PCI Interrupt, Error Interrupt and DMA Interrupt are
shared on a single IRQ line or at most 5 IRQs are used. The
GRPCI2 can mask/unmask PCI interrupts, Err and DMA in the control
and check status bits which tells us which IRQ really happended.
The GENIRQ layer is used to unmask/mask each individual IRQ
source by creating virtual IRQs and implementing a IRQ chip.
The optional DMA functionality of the GRPCI2 is not supported
by this patch.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* proper initialization of boot_cpu_id (no hardcoding to 0)
* use boot_cpu_id index to address into the IRQ controller where
appropriate
Each CPU has a separate set of IRQ controller registers, this
patch makes sure that the boot-cpu registers are used instead
of CPU0's.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A simple implementation of CPU affinity, the first CPU in
the affinity CPU mask always takes the IRQ.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleaned up leon_init_timers() by removing unnecessary double checking
and one indentation level. Changed LEON_IMASK to LEON_IMASK(cpu).
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The extended IRQ controller gives the LEON 16 more IRQs.
The patch installs a custom handler for the exetended controller
IRQ, where a register is read and the "real" IRQ causing IRQ is
determined.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LEON interrupt controller has one single mask register for all
IRQs per CPU, even though the genirq layer protects us from accessing
the same IRQ at the same time other IRQs share the same mask register
and may thus interfere. Some other IRQ controllers has a mask register
or similar per IRQ instead which makes spinlocks unncessary.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The conversion of sparc32 to genirq is based on original work done
by David S. Miller.
Daniel Hellstrom has helped in the conversion and implemented
the shutdowm functionality.
Marcel van Nies <morcles@gmail.com> has tested this on Sparc Station 20
Test status:
sun4c - not tested
sun4m,pci - not tested
sun4m,sbus - tested (Sparc Classic, Sparc Station 5, Sparc Station 20)
sun4d - not tested
leon - tested on various combinations of leon boards,
including SMP variants
generic
Introduce use of GENERIC_HARDIRQS and GENERIC_IRQ_SHOW
Allocate 64 IRQs - which is enough even for SS2000
Use a table of irq_bucket to maintain uses IRQs
irq_bucket is also used to chain several irq's that
must be called when the same intrrupt is asserted
Use irq_link to link a interrupt source to the irq
All plafforms must now supply their own build_device_irq method
handler_irq rewriten to use generic irq support
floppy
Read FLOPPY_IRQ from platform device
Use generic request_irq to register the floppy interrupt
Rewrote sparc_floppy_irq to use the generic irq support
pcic:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for pcic
Use pcic_build_device_irq in pci_time_init
allocate virtual irqs in pcic_fill_irq
sun4c:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for sun4c
Use sun4c_build_device_irq in sun4c_init_timers
sun4m:
Introduce irq_chip
Introduce dedicated mask/unmask methods
Introduce sun4m_handler_data that allow easy access to necessary
data in the mask/unmask functions
Add a helper method to enable profile_timer (used from smp)
Added sun4m_build_device_irq
Use sun4m_build_device_irq in sun4m_init_timers
TODO:
There is no replacement for smp_rotate that always scheduled
next CPU as interrupt target upon an interrupt
sun4d:
Introduce irq_chip
Introduce dedicated mask/unmask methods
Introduce sun4d_handler_data that allow easy access to
necessary data in mask/unmask fuctions
Rewrote sun4d_handler_irq to use generic irq support
TODO:
The original implmentation of enable/disable had:
if (irq < NR_IRQS)
return;
The new implmentation does not distingush between SBUS and cpu
interrupts.
I am no sure what is right here. I assume we need to do
something for the cpu interrupts.
I have not succeeded booting my sun4d box (with or without this patch)
and my understanding of this platfrom is limited.
So I would be a bit suprised if this works.
leon:
Introduce irq_chip
Store mask in chip_data for use in mask/unmask functions
Add build_device_irq for leon
Use leon_build_device_irq in leon_init_timers
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Daniel Hellstrom <daniel@gaisler.com>
Tested-by: Marcel van Nies <morcles@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sparc_irq_config is used to hold the platform specific irq setup.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The way a LEON is powered down is implemented differently depending
on CHIP type. The AMBA Plug&Play system ID tells revision of GRLIB
and CHIP.
This is for example needed by the GR-LEON4-ITX board and the UT699.
Previously the power down support for LEON was limited to SMP, now
both SMP and UP systems use the instruction.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ability to select Timer Core and Timer instance for system clock
makes it possible for multiple AMP systems to coexist.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Needed for LEON AMP systems where different CPUs are routed to
different IRQ controllers. This patch selects the IRQ Controller
which has been routed to the boot CPU, it is up to the boot loader
to configure the IRQ controller.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
reflects the value of HZ
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For symbols still lacking namespace qualifiers, add an of_pdt_ prefix.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
Also fixes a typo in one message.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support SMP for a Sparc-Leon multiprocessor system.
Add Leon specific SMP code to arch/sparc/kernel/leon_smp.c.
Signed-off-by: Konrad Eisele <konrad@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro CONFIG_SPARC_LEON will shield, if undefined, the sun-sparc
code from LEON specific code. In
particular include/asm/leon.h will get empty through #ifdef and
leon_kernel.c and leon_mm.c will not be compiled.
Signed-off-by: Konrad Eisele <konrad@gaisler.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
