Age | Commit message (Collapse) | Author |
|
If we are context switched whilst copying into a thread's
vfp_hard_struct then the partial copy may be corrupted by the VFP
context switching code (see "ARM: vfp: flush thread hwstate before
restoring context from sigframe").
This patch updates the ptrace VFP set code so that the thread state is
flushed before the copy, therefore disabling VFP and preventing
corruption from occurring.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
In a preemptible kernel, vfp_set() can be preempted, causing the
hardware VFP context to be switched while the thread vfp state is
being read and modified. This leads to a race condition which can
cause the thread vfp state to become corrupted if lazy VFP context
save occurs due to preemption in between the time thread->vfpstate
is read and the time the modified state is written back.
This may occur if preemption occurs during the execution of a
ptrace() call which modifies the VFP register state of a thread.
Such instances should be very rare in most realistic scenarios --
none has been reported, so far as I am aware. Only uniprocessor
systems should be affected, since VFP context save is not currently
lazy in SMP kernels.
The problem was introduced by my earlier patch migrating to use
regsets to implement ptrace.
This patch does a vfp_sync_hwstate() before reading
thread->vfpstate, to make sure that the thread's VFP state is not
live in the hardware registers while the registers are modified.
Thanks to Will Deacon for spotting this.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Following execution of a signal handler, we currently restore the VFP
context from the ucontext in the signal frame. This involves copying
from the user stack into the current thread's vfp_hard_struct and then
flushing the new data out to the hardware registers.
This is problematic when using a preemptible kernel because we could be
context switched whilst updating the vfp_hard_struct. If the current
thread has made use of VFP since the last context switch, the VFP
notifier will copy from the hardware registers into the vfp_hard_struct,
overwriting any data that had been partially copied by the signal code.
Disabling preemption across copy_from_user calls is a terrible idea, so
instead we move the VFP thread flush *before* we update the
vfp_hard_struct. Since the flushing is performed lazily, this has the
effect of disabling VFP and clearing the CPU's VFP state pointer,
therefore preventing the thread from being updated with stale data on
the next context switch.
Cc: stable <stable@vger.kernel.org>
Tested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This reverts commit 3c424f359898aff48c3d5bed608ac706f8a528c3.
Joachim Eastwood reports:
| "ARM: 7304/1: ioremap: fix boundary check when reusing static mapping"
| Commit: 3c424f359898aff48c3d5bed608ac706f8a528c3 in Linus master
|
| Breaks booting on my custom AT91RM9200 board.
| There isn't any error messages or anything that indicates what goes
| wrong it just stops after; Uncompressing Linux... done, booting the
| kernel.
|
| Reverting it makes my board boot again.
and further debugging reveals:
ioremap: pfn=fffff phys=fffff000 offset=400 size=1000
ioremap: area c3ffdfc0: phys_addr=200000 pfn=200 size=4000
ioremap: found: addr fef74000 => fed73000 => fed73400
Clearly, an area for pfn 0x200, 16K can't ever satisfy a request for pfn
0xfffff. This happens because the changed if statement becomes:
if (0x00200 > 0xfffff ||
0xfffff000 + 0x400 + 0x1000-1 > 0x00200000 + 0x4000-1)
and therefore:
if (0x00200 > 0xfffff ||
0x000003ff > 0x00203fff)
The if condition fails, and so we _believe_ that the SRAM mapping fits
our request. Clearly that's totally bogus.
Moreover, the original premise of the 'fix' patch was wrong:
| The condition checking boundaries of the requested and existing
| mappings didn't take in-page offset into consideration though,
| which lead to obscure and hard to debug problems when requested
| mapping crossed end of the static one.
as the code immediately above this loop does:
size = PAGE_ALIGN(offset + size);
so 'size' already contains the requested offset into the page.
So, revert the broken 'fix'.
Acked-by: Nicolas Pitre <nico@linaro.org>
|
|
Both sparc 32-bit's software divide assembler and MPILIB provide
clz_tab[] with identical contents.
Break it out into a seperate object file and select it when
SPARC32 or MPILIB is set.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Return to behaviour perf MSR had before introducing vPMU in case vPMU
is disabled. Some guests access those registers unconditionally and do
not expect it to fail.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
On hosts without this patch, 32bit guests will crash (and 64bit guests
may behave in a wrong way) for example by simply executing following
nasm-demo-application:
[bits 32]
global _start
SECTION .text
_start: syscall
(I tested it with winxp and linux - both always crashed)
Disassembly of section .text:
00000000 <_start>:
0: 0f 05 syscall
The reason seems a missing "invalid opcode"-trap (int6) for the
syscall opcode "0f05", which is not available on Intel CPUs
within non-longmodes, as also on some AMD CPUs within legacy-mode.
(depending on CPU vendor, MSR_EFER and cpuid)
Because previous mentioned OSs may not engage corresponding
syscall target-registers (STAR, LSTAR, CSTAR), they remain
NULL and (non trapping) syscalls are leading to multiple
faults and finally crashs.
Depending on the architecture (AMD or Intel) pretended by
guests, various checks according to vendor's documentation
are implemented to overcome the current issue and behave
like the CPUs physical counterparts.
[mtosatti: cleanup/beautify code]
Signed-off-by: Stephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
In order to be able to proceed checks on CPU-specific properties
within the emulator, function "get_cpuid" is introduced.
With "get_cpuid" it is possible to virtually call the guests
"cpuid"-opcode without changing the VM's context.
[mtosatti: cleanup/beautify code]
Signed-off-by: Stephan Baerwolf <stephan.baerwolf@tu-ilmenau.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
commit 43db595e8b5d78ce5ad2feab719814a76e3ad2e5
(sh: switch to GENERIC_PCI_IOMAP)
failed to take into account the PCI channels's
io_map_base for mapping IO BARs.
This also caused a new warning on sh.
Fix this, without re-introducing code duplication,
by setting NO_GENERIC_PCI_IOPORT_MAP
and supplying a sh-specific __pci_ioport_map.
Reported-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
commit eab90291d35438bcebf7c3dc85be66d0f24e3002
(mips: switch to GENERIC_PCI_IOMAP)
failed to take into account the PCI controller's
io_map_base for mapping IO BARs.
This also caused a new warning on mips.
Fix this, without re-introducing code duplication,
by setting NO_GENERIC_PCI_IOPORT_MAP
and supplying a mips-specific __pci_ioport_map.
Reported-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit d761f0c521868e59cd0bc59159cbdb4686fe210d.
Patch: "cpu: Register a generic CPU device on architectures that currently do not"
(sha1: 9f13a1fd452f11c18004ba2422a6384b424ec8a9)
selects GENERIC_CPU_DEVICES for Microblaze which register cpu.
My patch was done in the same time that's why cpu was registered twice which
caused this warning log:
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:481 sysfs_add_one+0xb0/0xdc()
sysfs: cannot create duplicate filename '/devices/system/cpu/cpu0'
Modules linked in:
...
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] dasd: revalidate server for new pathgroup
[S390] dasd: revert LCU optimization
[S390] cleanup entry point definition
|
|
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: generic atomic64 support
|
|
This commit removes the reboot quirk originally added by commit
e19e074 ("x86: Fix reboot problem on VersaLogic Menlow boards").
Testing with a VersaLogic Ocelot (VL-EPMs-21a rev 1.00 w/ BIOS
6.5.102) revealed the following regarding the reboot hang
problem:
- v2.6.37 reboot=bios was needed.
- v2.6.38-rc1: behavior changed, reboot=acpi is needed,
reboot=kbd and reboot=bios results in system hang.
- v2.6.38: VersaLogic patch (e19e074 "x86: Fix reboot problem on
VersaLogic Menlow boards") was applied prior to v2.6.38-rc7. This
patch sets a quirk for VersaLogic Menlow boards that forces the use
of reboot=bios, which doesn't work anymore.
- v3.2: It seems that commit 660e34c ("x86: Reorder reboot method
preferences") changed the default reboot method to acpi prior to
v3.0-rc1, which means the default behavior is appropriate for the
Ocelot. No VersaLogic quirk is required.
The Ocelot board used for testing can successfully reboot w/out
having to pass any reboot= arguments for all 3 current versions
of the BIOS.
Signed-off-by: Michael D Labriola <michael.d.labriola@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Michael D Labriola <mlabriol@gdeb.com>
Cc: Kushal Koolwal <kushalkoolwal@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/87vcnub9hu.fsf@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Skip DMI checks for vendor specific reboot quirks if the user
passed in a reboot= arg on the command line - we should never
override user choices.
Signed-off-by: Michael D Labriola <michael.d.labriola@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Michael D Labriola <mlabriol@gdeb.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/87wr8ab9od.fsf@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: arch/arm/mach-omap2/smartreflex.c: add missing iounmap
ARM: OMAP2+: arch/arm/mach-omap2/devices.c: introduce missing kfree
ARM: OMAP: fix MMC2 loopback clock handling
ARM: OMAP: fix erroneous mmc2 clock change on mmc3 setup
ARM: OMAP2+: GPMC: fix device size setup
ARM: OMAP2+: timer: Fix crash due to wrong arg to __omap_dm_timer_read_counter
ARM: OMAP3: hwmod data: register dss hwmods after dss_core
ARM: OMAP2/3: PRM: fix missing plat/irqs.h build breakage
ARM: OMAP2+: io: fix compilation breakage on 2420-only configs
ARM: OMAP4: hwmod data: Add names for DMIC memory address space
ARM: OMAP3: hwmod data: add SYSC_HAS_ENAWAKEUP for dispc
ARM: OMAP2+: hwmod data: split omap2/3 dispc hwmod class
ARM: OMAP2: fix regulator warnings
ARM: OMAP2: fix omap3 touchbook kconfig warning
i2c: OMAP: Fix OMAP1 build error
|
|
fixes
* 'fixes' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: update mdio bus name
ARM: davinci: DA850: remove non-existing pll1_sysclk4-7 clocks
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
* 'stable/for-linus-fixes-3.3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/granttable: Disable grant v2 for HVM domains.
x86: xen: size struct xen_spinlock to always fit in arch_spinlock_t
|
|
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm: (31 commits)
ARM: 7304/1: ioremap: fix boundary check when reusing static mapping
ARM: 7301/1: Rename the T() macro to TUSER() to avoid namespace conflicts
ARM: 7299/1: ftrace: clear zero bit in reported IPs for Thumb-2
ARM: 7298/1: realview: fix mapping of MPCore private memory region
PCMCIA: fix sa1111 oops on remove
ARM: 7288/1: mach-sa1100: add missing module_init() call
ARM: 7297/1: smp_twd: make sure timer is stopped before registering it
ARM: 7296/1: proc-v7.S: remove HARVARD_CACHE preprocessor guards
ARM: 7295/1: cortex-a7: move proc_info out of !CONFIG_ARM_LPAE block
ARM: 7293/1: logical_cpu_map: decouple CPU mapping from SMP
ARM: 7291/1: cache: assume 64-byte L1 cachelines for ARMv7 CPUs
ARM: 7290/1: vmlinux.lds.S: align the exception fixup table to a 4-byte boundary
ARM: 7289/1: vmlinux.lds.S: do not hardcode cacheline size as 32 bytes
MFD: ucb1x00-ts: fix resume failure
MFD: ucb1x00-core: fix gpiolib direction_output handling
MFD: ucb1x00-core: fix missing restore of io output data on resume
MFD: mcp-core: fix mcp_priv() to be more type safe
MFD: mcp-core: fix complaints from the genirq layer
Revert "ARM: sa11x0: Implement autoloading of codec and codec pdata for mcp bus."
Revert "ARM: sa1100: Refactor mcp-sa11x0 to use platform resources."
...
Fix up conflict due to arch/arm/mach-mx5/Kconfig having been merged into
mach-imx5 (commit 784a90c0a7d8: "ARM i.MX: Merge i.MX5 support into
mach-imx"), but the ARM_L1_CACHE_SHIFT_6 entry was moved to be driven by
the CPU_V7 logic from it in the old location in rmk's branch (commit
a092f2b15399: "ARM: 7291/1: cache: assume 64-byte L1 cachelines for
ARMv7 CPUs").
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
arm-soc fixes for 3.3-rc:
AT91 needed reset fixes which resulted in some minor code refactoring,
it also adds a feature-removal for one of their platforms for 3.4.
The USB patches have been acked by Greg K-H.
i.MX and ux500 both have some minor fixes, nothing controversial.
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-imx/mach-mx53_ard.c: add missing iounmap
ARM: imx: iomux-v1.h: Fix build error due to __init annotation
ARM: at91: Fix at91sam9g45 and at91cap9 reset
ARM: at91: make rstc soc independent
ARM: at91: introduce AT91_SAM9_ALT_RESET to select the at91sam9 alternative reset
ARM: at91: merge at91cap9_ddrsdr.h in at91sam9_ddrsdr.h
ARM: at91: fix cap9 ddrsdr register
ARM/USB: at91/ohci-at91: rename vbus_pin_inverted to vbus_pin_active_low
USB: at91: fix clk_get error handling
ARM: at91: removal of CAP9 SoC family
ARM: at91: fix at91rm9200 soc subtype handling
mach-ux500: no MMC_CAP_SD_HIGHSPEED on Snowball
mach-ux500: enable ARM errata 764369
mach-ux500: do not override outer.inv_all
mach-ux500: musb: now musb is always in OTG mode
ARM: imx6: add missing twd_clk for imx6q clock
|
|
Smatch complains that we have some inconsistent NULL checking.
If "task" were NULL then it would lead to a NULL dereference
later. We can remove this test because earlier on in the
function we have:
if (!task)
task = current;
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Clemens Ladisch <clemens@ladisch.de>
Link: http://lkml.kernel.org/r/20120128105246.GA25092@elgon.mountain
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Since commit 576d2f2525612ecb5af029a76f21f22a3b82563d "ARM: add
generic ioremap optimization by reusing static mappings" ioremap()
is trying to reuse existing static mapping when possible.
The condition checking boundaries of the requested and existing
mappings didn't take in-page offset into consideration though,
which lead to obscure and hard to debug problems when requested
mapping crossed end of the static one.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 5a05a8200a4359ef2bfe9094c137dee35cfdd516 ("davinci_emac:
use an unique MDIO bus name") introduced during the v3.3 merge
window updated the davinci mdio bus name to make it unique.
Update the bus name in board files which use DaVinci MDIO bus
to match the new name. Without this PHY is not detected with
error like:
PHY 0:01 not found
net eth0: could not connect to phy 0:01
Tested on DM365 and DA850 EVMs.
Cc: Florian Fainelli <florian@openwrt.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
* commit 'v3.3-rc1': (9775 commits)
Linux 3.3-rc1
x86, syscall: Need __ARCH_WANT_SYS_IPC for 32 bits
qnx4: don't leak ->BitMap on late failure exits
qnx4: reduce the insane nesting in qnx4_checkroot()
qnx4: di_fname is an array, for crying out loud...
KEYS: Permit key_serial() to be called with a const key pointer
keys: fix user_defined key sparse messages
ima: fix cred sparse warning
uml: fix compile for x86-64
MPILIB: Add a missing ENOMEM check
tpm: fix (ACPI S3) suspend regression
nvme: fix merge error due to change of 'make_request_fn' fn type
xen: using EXPORT_SYMBOL requires including export.h
gpio: tps65910: Use correct offset for gpio initialization
acpi/apei/einj: Add extensions to EINJ from rev 5.0 of acpi spec
intel_idle: Split up and provide per CPU initialization func
ACPI processor: Remove unneeded variable passed by acpi_processor_hotadd_init V2
tg3: Fix single-vector MSI-X code
openvswitch: Fix multipart datapath dumps.
ipv6: fix per device IP snmp counters
...
|
|
fixes
* 'imx-fixes' of git://git.pengutronix.de/git/imx/linux-2.6:
arch/arm/mach-imx/mach-mx53_ard.c: add missing iounmap
ARM: imx: iomux-v1.h: Fix build error due to __init annotation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
* 'fixes-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
mach-ux500: no MMC_CAP_SD_HIGHSPEED on Snowball
mach-ux500: enable ARM errata 764369
mach-ux500: do not override outer.inv_all
mach-ux500: musb: now musb is always in OTG mode
|
|
into fixes
* 'imx6/fixes' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6: add missing twd_clk for imx6q clock
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc32: forced setting of mode of sun4m per-cpu timers
|
|
|
|
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
pdata needs to be freed before leaving the function in an error case.
A simplified version of the semantic match that finds the problem is as
follows: (http://coccinelle.lip6.fr)
// <smpl>
@r exists@
local idexpression x;
statement S;
identifier f1;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
x->f1
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Currently MMC2 setup code can only enable loopback clock and
relies on reset value for boards that need to have it disabled.
This causes a problem with certain bootloaders that always enable
that clock, resulting with unwanted bootloader dependencies.
Fix this by making it disable the clock if board data says so.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
hsmmc23_before_set_reg() can set MMCSDIO2ADPCLKISEL bit, which
enables internal clock for MMC2. Currently this function is also called
by code handling MMC3, and if .internal_clock is set in platform data
(by default it currently is), it will set MMCSDIO2ADPCLKISEL for MMC2
instead of MMC3 (MMC3 doesn't have such bit so nothing actually needs to
be done). This breaks 2nd SD slot on pandora.
Fix this by changing hsmmc23_before_set_reg() to only handle MMC2.
Note that this removes .remux() call for MMC3, but no board currently
needs it and it's also not called for MMC4 and MMC5.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
following statement can only change device size from 8-bit(0) to 16-bit(1),
but not vice versa:
regval |= GPMC_CONFIG1_DEVICESIZE(wval);
so as this field has 1 reserved bit, that could be used in future,
just clear both bits and then OR with the desired value
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 2f0778af (ARM: 7205/2: sched_clock: allow sched_clock to be
selected at runtime) had a typo for the case when CONFIG_OMAP_32K_TIMER
is not set.
In dmtimer_read_sched_clock(), wrong argument was getting passed to
__omap_dm_timer_read_counter() function call; instead of "&clksrc",
we were passing "clksrc.io_base", which results into kernel crash.
To reproduce kernel crash, just disable the CONFIG_OMAP_32K_TIMER config
option (and DEBUG_LL) and build/boot the kernel.
This will use dmtimer as a kernel clocksource and lead to kernel
crash during boot -
[ 0.000000] OMAP clocksource: GPTIMER2 at 26000000 Hz
[ 0.000000] sched_clock: 32 bits at 26MHz, resolution 38ns, wraps every
165191ms
[ 0.000000] Unable to handle kernel paging request at virtual address
00030ef1
[ 0.000000] pgd = c0004000
[ 0.000000] [00030ef1] *pgd=00000000
[ 0.000000] Internal error: Oops: 5 [#1] SMP
[ 0.000000] Modules linked in:
[ 0.000000] CPU: 0 Not tainted (3.3.0-rc1-11574-g0c76665-dirty #3)
[ 0.000000] PC is at dmtimer_read_sched_clock+0x18/0x4c
[ 0.000000] LR is at update_sched_clock+0x10/0x84
[ 0.000000] pc : [<c00243b8>] lr : [<c0018684>] psr: 200001d3
[ 0.000000] sp : c0641f38 ip : c0641e18 fp : 0000000a
[ 0.000000] r10: 151c3303 r9 : 00000026 r8 : 76276259
[ 0.000000] r7 : 00028547 r6 : c065ac80 r5 : 431bde82 r4 : c0655968
[ 0.000000] r3 : 00030ef1 r2 : fb032000 r1 : 00000028 r0 : 00000001
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode_amd: Add support for CPU family specific container files
x86/amd: Add missing feature flag for fam15h models 10h-1fh processors
x86/boot-image: Don't leak phdrs in arch/x86/boot/compressed/misc.c::Parse_elf()
x86/numachip: Drop unnecessary conflict with EDAC
x86/uv: Fix uninitialized spinlocks
x86/uv: Fix uv_gpa_to_soc_phys_ram() shift
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Fix assembler constraint to prevent overeager gcc optimisation
mac_esp: rename irq
mac_scsi: dont enable mac_scsi irq before requesting it
macfb: fix black and white modes
m68k/irq: Remove obsolete IRQ_FLG_* definitions
Fix up trivial conflict in arch/m68k/kernel/process_mm.c as per Geert.
|
|
rsyslog will display KERN_EMERG messages on a connected
terminal. However, these messages are useless/undecipherable
for a general user.
For example, after a softlockup we get:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Stack:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Call Trace:
Message from syslogd@intel-s3e37-04 at Jan 25 14:18:06 ...
kernel:Code: ff ff a8 08 75 25 31 d2 48 8d 86 38 e0 ff ff 48 89
d1 0f 01 c8 0f ae f0 48 8b 86 38 e0 ff ff a8 08 75 08 b1 01 4c 89 e0 0f 01 c9 <e8> ea 69 dd ff 4c 29 e8 48 89 c7 e8 0f bc da ff 49 89 c4 49 89
This happens because the printk levels for these messages are
incorrect. Only an informational message should be displayed on
a terminal.
I modified the printk levels for various messages in the kernel
and tested the output by using the drivers/misc/lkdtm.c kernel
modules (ie, softlockups, panics, hard lockups, etc.) and
confirmed that the console output was still the same and that
the output to the terminals was correct.
For example, in the case of a softlockup we now see the much
more informative:
Message from syslogd@intel-s3e37-04 at Jan 25 10:18:06 ...
BUG: soft lockup - CPU4 stuck for 60s!
instead of the above confusing messages.
AFAICT, the messages no longer have to be KERN_EMERG. In the
most important case of a panic we set console_verbose(). As for
the other less severe cases the correct data is output to the
console and /var/log/messages.
Successfully tested by me using the drivers/misc/lkdtm.c module.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: dzickus@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1327586134-11926-1-git-send-email-prarit@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Quite oddly, all of the arguments passed through from the top
level macros to the second level which didn't need parentheses
had them, while the only expression (involving a parameter)
needing them didn't.
Very recently I got bitten by the lack thereof when using
something like "array + index" for the first operand, with
"array" being an array more narrow than int.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/4F2183A9020000780006F3E6@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add missing iounmap in error handling code, in a case where the function
already preforms iounmap on some other execution path.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
statement S,S1;
int ret;
@@
e = \(ioremap\|ioremap_nocache\)(...)
... when != iounmap(e)
if (<+...e...+>) S
... when any
when != iounmap(e)
*if (...)
{ ... when != iounmap(e)
return ...; }
... when any
iounmap(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Fix the following build error found when building imx_v4_v5_defconfig:
CC arch/arm/mach-imx/mach-imx27ipcam.o
In file included from arch/arm/plat-mxc/include/mach/iomux-mx27.h:23,
from arch/arm/mach-imx/mach-imx27ipcam.c:22:
arch/arm/plat-mxc/include/mach/iomux-v1.h:99: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'imx_iomuxv1_init'
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
A hardware bug in the OMAP4 HDMI PHY causes physical damage to the board
if the HDMI PHY is kept powered on when the cable is not connected.
This patch solves the problem by adding hot-plug-detection into the HDMI
IP driver. This is not a real HPD support in the sense that nobody else
than the IP driver gets to know about the HPD events, but is only meant
to fix the HW bug.
The strategy is simple: If the display device is turned off by the user,
the PHY power is set to OFF. When the display device is turned on by the
user, the PHY power is set either to LDOON or TXON, depending on whether
the HDMI cable is connected.
The reason to avoid PHY OFF when the display device is on, but the cable
is disconnected, is that when the PHY is turned OFF, the HDMI IP is not
"ticking" and thus the DISPC does not receive pixel clock from the HDMI
IP. This would, for example, prevent any VSYNCs from happening, and
would thus affect the users of omapdss. By using LDOON when the cable is
disconnected we'll avoid the HW bug, but keep the HDMI working as usual
from the user's point of view.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Both Panda and 4430SDP use GPIO 63 as HDMI hot-plug-detect. Configure
this GPIO in the board files.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The HDMI GPIO pins LS_OE and CT_CP_HPD are not currently configured.
This patch configures them as output pins.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.
So remove the muxing for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The GPIO 60 on 4430sdp and Panda is not HPD GPIO, as currently marked in
the board files, but CT_CP_HPD, which is used to enable/disable HPD
functionality.
This patch renames the GPIO.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Instead of freeing the GPIOs individually, use gpio_free_array().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
We've decided to provide CPU family specific container files
(starting with CPU family 15h). E.g. for family 15h we have to
load microcode_amd_fam15h.bin instead of microcode_amd.bin
Rationale is that starting with family 15h patch size is larger
than 2KB which was hard coded as maximum patch size in various
microcode loaders (not just Linux).
Container files which include patches larger than 2KB cause
different kinds of trouble with such old patch loaders. Thus we
have to ensure that the default container file provides only
patches with size less than 2KB.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/20120120164412.GD24508@alberich.amd.com
[ documented the naming convention and tidied the code a bit. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|