| Age | Commit message (Collapse) | Author |
|---|
|
Add pwm device and pwm-backlight for imx23-evk and imx28-evk.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Enable rtc for imx23 and imx28.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add heartbeat gpio-leds for imx28-evk board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add missing properties for fec, phy-supply, phy-reset-gpios and
phy-reset-duration, which are required by fec driver for successfully
probe fec from device tree, if bootloader hasn't set those things up.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add vmmc-supply for mmc device, so that the power to mmc slot can be
turned on by mmc driver if bootloader hasn't done it.
Also remove "okay" status for mmc1/ssp1, as the device has pin conflict
with gpmi-nand. Actually the device is already disabled since the
mxs-mmc driver adopts pinctrl support because there is no pinctrl setup
for the device in dts. Make this explicit by removing "okay" status.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add auart device for imx23-evk board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The 8-bit mode mmc has pin conflicts with display. Let's use 4-bit
mode by default, so that display can be enabled together later.
Also add vmmc-supply for mmc device.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Before gpio_request can directly ask pinctrl system to configure the
requested pin into gpio mode, we use "hog" entry (pinctrl state of
pin controller itself) to configure gpios.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add comments for pinmux-ids so that we do not have to keep looking at
Documentation/devicetree/bindings/pinctrl/fsl,mxs-pinctrl.txt to read
all these pinmux-ids.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Use auxdata to attach mxsfb_platform_data for imx23-evk and imx28-evk.
We take this as a temporary solution for removing those board files,
and it should be updated to use common bindings for struct fb_videomode
when it becomes available.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Move mxsfb.h into include/linux, so that mxsfb driver does not have to
include <mach/*> header.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
As the flexcan driver has DT binding for some time now. This patch makes
the flexcan driver available in the can drivers menu if a SOC with flexcan
is enabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lily <brian@crystalfontz.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Brian Lily <brian@crystalfontz.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The non-DT boot reads the mac from OTP and pass it to fec driver via
platform data. The patch provides an equivalent support for device
tree boot, with reading mac from OTP and store it in device tree,
and fec driver can get the mac from device tree at its probe time.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add auart0 and auart3 support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Replace "gpmi" with "gpmi-nand" to get the
GPMI interface probing with DT instead of
failing to get clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
CC: Dong Aisheng <b29396@freescale.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Linux ARM kernel <linux-arm-kernel@lists.infradead.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
add gpmi-nand device tree support.
add gpmi-nand pinctrl support.
Also enable the gpmi support for mx28-evk board.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another week, another batch of fixes.
All are small, contained, targeted fixes for explicit problems --
mostly build and boot failures across i.MX, OMAP, Renesas/Shmobile and
Samsung."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx6q: fix suspend regression caused by common clk migration
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
* 'v3.5-samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix EXYNOS_DEV_DMA Kconfig entry
ARM: SAMSUNG: Fix for S3C2412 EBI memory mapping
ARM: SAMSUNG: Should check for IS_ERR(clk) instead of NULL
|
|
When moving to common clk framework, the imx6q clks rom and mmdc_ch1_axi
get different on/off states than old clk driver, which breaks suspend
function. There might be a better way to manage these clocks, but let's
takes the old clk driver approach to fix the regression first.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
"Here's one more regression fix that I missed earlier, and a
trivial fix to get omap4470 booting."
* tag 'omap-fixes-for-v3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP4470: Fix OMAP4470 boot failure
ARM: OMAP2+: nand: fix build error when CONFIG_MTD_ONENAND_OMAP2=n
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Power Management patches from Len Brown.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
acpi_pad: fix power_saving thread deadlock
ACPI video: Still use ACPI backlight control if _DOS doesn't exist
ACPI, APEI, Avoid too much error reporting in runtime
ACPI: Add a quirk for "AMILO PRO V2030" to ignore the timer overriding
ACPI: Remove one board specific WARN when ignoring timer overriding
ACPI: Make acpi_skip_timer_override cover all source_irq==0 cases
ACPI, x86: fix Dell M6600 ACPI reboot regression via DMI
ACPI sysfs.c strlen fix
|
|
'video-bugzilla-43168', 'bugzilla-40002' and 'bugfix-misc' into release
bug fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc fixes from Benjamin Herrenschmidt:
"Here are a few powerpc fixes. Arguably some of this should have come
to you earlier but I'm only just catching up after my medical leave.
Mostly these fixes regressions, a couple are long standing bugs."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/pseries: Fix software invalidate TCE
powerpc: check_and_cede_processor() never cedes
powerpc/ftrace: Do not trace restore_interrupts()
powerpc: Fix Section mismatch warnings in prom_init.c
ppc64: fix missing to check all bits of _TIF_USER_WORK_MASK in preempt
powerpc: Fix uninitialised error in numa.c
powerpc: Fix BPF_JIT code to link with multiple TOCs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar.
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Remove stray %s, add -w to mkcapflags.pl
x86, cpufeature: Catch duplicate CPU feature strings
x86, cpufeature: Rename X86_FEATURE_DTS to X86_FEATURE_DTHERM
x86: Fix kernel-doc warnings
x86, compat: Use test_thread_flag(TIF_IA32) in compat signal delivery
|
|
The following added support for powernv but broke pseries/BML:
1f1616e powerpc/powernv: Add TCE SW invalidation support
TCE_PCI_SW_INVAL was split into FREE and CREATE flags but the tests in
the pseries code were not updated to reflect this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@kernel.org [v3.3+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit f948501b36c6 ("Make hard_irq_disable() actually hard-disable
interrupts") caused check_and_cede_processor to stop working.
->irq_happened will never be zero right after a hard_irq_disable
so the compiler removes the call to cede_processor completely.
The bug was introduced back in the lazy interrupt handling rework
of 3.4 but was hidden until recently because hard_irq_disable did
nothing.
This issue will eventually appear in 3.4 stable since the
hard_irq_disable fix is marked stable, so mark this one for stable
too.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
As I was adding code that affects all archs, I started testing function
tracer against PPC64 and found that it currently locks up with 3.4
kernel. I figured it was due to tracing a function that shouldn't be, so
I went through the following process to bisect to find the culprit:
cat /debug/tracing/available_filter_functions > t
num=`wc -l t`
sed -ne "1,${num}p" t > t1
let num=num+1
sed -ne "${num},$p" t > t2
cat t1 > /debug/tracing/set_ftrace_filter
echo function /debug/tracing/current_tracer
<failed? bisect t1, if not bisect t2>
It finally came down to this function: restore_interrupts()
I'm not sure why this locks up the system. It just seems to prevent
scheduling from occurring. Interrupts seem to still work, as I can ping
the box. But all user processes freeze.
When restore_interrupts() is not traced, function tracing works fine.
Cc: stable@kernel.org
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
This patches tries to fix a couple of Section mismatch warnings like
following one:
WARNING: arch/powerpc/kernel/built-in.o(.text+0x2923c): Section mismatch
in reference from the function .prom_query_opal() to the
function .init.text:.call_prom()
The function .prom_query_opal() references
the function __init .call_prom().
This is often because .prom_query_opal lacks a __init
annotation or the annotation of .call_prom is wrong.
Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
In entry_64.S version of ret_from_except_lite, you'll notice that
in the !preempt case, after we've checked MSR_PR we test for any
TIF flag in _TIF_USER_WORK_MASK to decide whether to go to do_work
or not. However, in the preempt case, we do a convoluted trick to
test SIGPENDING only if PR was set and always test NEED_RESCHED ...
but we forget to test any other bit of _TIF_USER_WORK_MASK !!! So
that means that with preempt, we completely fail to test for things
like single step, syscall tracing, etc...
This should be fixed as the following path:
- Test PR. If not set, go to resume_kernel, else continue.
- If go resume_kernel, to do that original do_work.
- If else, then always test for _TIF_USER_WORK_MASK to decide to do
that original user_work, else restore directly.
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
chroma_defconfig currently gives me this with gcc 4.6:
arch/powerpc/mm/numa.c:638:13: error: 'dm' may be used uninitialized in this function [-Werror=uninitialized]
It's a bogus warning/error since of_get_drconf_memory() only writes it
anyway.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: <stable@kernel.org> [v3.3+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
If the kernel is big enough (eg. allyesconfig), the linker may need to
switch TOCs when calling from the BPF JIT code out to the external
helpers (skb_copy_bits() & bpf_internal_load_pointer_neg_helper()).
In order to do that we need to leave space after the bl for the linker
to insert a reload of our TOC pointer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
|
|
sh_clk_mstp32_register is deprecated. This convert to sh_clk_mstp_register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Fix compile breakage caused by
commit aa82f9fcd0062782dcbe29a2c820ba7c04dbe572
Author: Paul Mundt <lethal@linux-sh.org>
sh: kfr2r09 evt2irq migration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull a m68knommu fix from Greg Ungerer:
"It contains a single fix for breakage using the Freescale FEC eth
driver on ColdFire CPUs."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: define a local devm_clk_get() function
|
|
OMAP4470 currently fails to boot, printing various messages such as ...
omap_hwmod: mpu: cannot clk_get main_clk dpll_mpu_m2_ck
omap_hwmod: mpu: cannot _init_clocks
------------[ cut here ]------------
WARNING: at arch/arm/mach-omap2/omap_hwmod.c:2062 _init+0x2a0/0x2e4()
omap_hwmod: mpu: couldn't init clocks
Modules linked in:
[<c001c7fc>] (unwind_backtrace+0x0/0xf4) from [<c0043c64>] (warn_slowpath_common+0x4c/0x64)
[<c0043c64>] (warn_slowpath_common+0x4c/0x64) from [<c0043d10>] (warn_slowpath_fmt+0x30/0x40)
[<c0043d10>] (warn_slowpath_fmt+0x30/0x40) from [<c0674208>] (_init+0x2a0/0x2e4)
[<c0674208>] (_init+0x2a0/0x2e4) from [<c067428c>] (omap_hwmod_setup_one+0x40/0x60)
[<c067428c>] (omap_hwmod_setup_one+0x40/0x60) from [<c0674280>] (omap_hwmod_setup_one+0x34/0x60)
[<c0674280>] (omap_hwmod_setup_one+0x34/0x60) from [<c06726f4>] (omap_dm_timer_init_one+0x30/0x250)
[<c06726f4>] (omap_dm_timer_init_one+0x30/0x250) from [<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108)
[<c0672930>] (omap2_gp_clockevent_init+0x1c/0x108) from [<c0672c60>] (omap4_timer_init+0x10/0x5c)
[<c0672c60>] (omap4_timer_init+0x10/0x5c) from [<c066c418>] (time_init+0x20/0x30)
[<c066c418>] (time_init+0x20/0x30) from [<c0668814>] (start_kernel+0x1b0/0x304)
[<c0668814>] (start_kernel+0x1b0/0x304) from [<80008044>] (0x80008044)
---[ end trace 1b75b31a2719ed1c ]---
The problem is that currently none of the clocks are being registered for
OMAP4470 devices and so on boot-up no clocks can be found and the kernel panics.
This fix allows the kernel to boot without failure using a simple RAMDISK file
system on OMAP4470 blaze board.
Per feedback from Paul and Benoit the 4470 clock data is incomplete for new
modules such as the 2D graphics block that has been added to the 4470.
Therefore add a warning to indicate that the clock data is incomplete.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Commit 20ef9e08 ("ARM: EXYNOS: Support DMA for EXYNOS5250 SoC")
renamed EXYNOS4_DEV_DMA to EXYNOS_DEV_DMA. But some machine entries
still had EXYNOS4_DEV_DMA. Changed them to EXYNOS_DEV_DMA.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
There was a stray %s left from testing, remove it.
Add -w to the #! line (which is parsed by Perl even if the Perl
interpreter is invoked explicitly on the command line) to catch these
kinds of errors in the future.
Reported-by: Jean Delvare <khali@linux-fr.org>
Link: http://lkml.kernel.org/r/20120626143246.0c9bf301@endymion.delvare
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
commit 8259573b (ARM: OMAP2+: nand: Make board_onenand_init() visible
to board code) broke the build for configs with OneNAND disabled. By
removing the static in the header file, it created a duplicate definition
in the .c and the .h files, resuling in a build error:
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.c:102:111: error: redefinition of 'board_onenand_init'
/work/kernel/omap/dev/arch/arm/mach-omap2/board-flash.h:56:51: note: previous definition of 'board_onenand_init' was here
make[2]: *** [arch/arm/mach-omap2/board-flash.o] Error 1
make[2]: *** Waiting for unfinished jobs....
make[1]: *** [arch/arm/mach-omap2] Error 2
make: *** [sub-make] Error 2
Fix this by removing the duplicate dummy entry from the C file.
Cc: Enric Balletbò i Serra <eballetbo@gmail.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab.
Trivial conflict due to new USB HID ID's being added next to each other
(Baanto vs Axentia).
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (44 commits)
[media] smia: Fix compile failures
[media] Fix VIDIOC_DQEVENT docbook entry
[media] s5p-fimc: Fix control creation function
[media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file
[media] s5p-mfc: Fix setting controls
[media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT
[media] v4l/s5p-mfc: corrected encoder v4l control definitions
[media] v4l: mem2mem_testdev: Fix race conditions in driver
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] cxd2820r: Fix an incorrect modulation type bitmask
[media] em28xx: Show a warning if the board does not support remote controls
[media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD
[media] USB: Staging: media: lirc: initialize spinlocks before usage
[media] Revert "[media] media: mx2_camera: Fix mbus format handling"
[media] bw-qcam: driver and pixfmt documentation fixes
[media] cx88: fix firmware load on big-endian systems
[media] cx18: support big-endian systems
[media] ivtv: fix support for big-endian systems
[media] tuner-core: return the frequency range of the correct tuner
[media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()
...
|
|
We had a case of duplicate CPU feature strings, a user space ABI
violation, for almost two years. Make it a build error so that
doesn't happen again.
Link: http://lkml.kernel.org/r/4FE34BCB.5050305@linux.intel.com
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Jean Delvare <khali@linux-fr.org>
|
|
It makes sense to label "Digital Thermal Sensor" as "DTS", but
unfortunately the string "dts" was already used for "Debug Store", and
/proc/cpuinfo is a user space ABI.
Therefore, rename this to "dtherm".
This conflict went into mainline via the hwmon tree without any x86
maintainer ack, and without any kind of hint in the subject.
a4659053 x86/hwmon: fix initialization of coretemp
Reported-by: Jean Delvare <khali@linux-fr.org>
Link: http://lkml.kernel.org/r/4FE34BCB.5050305@linux.intel.com
Cc: Jan Beulich <JBeulich@suse.com>
Cc: <stable@vger.kernel.org> v2.6.36..v3.4
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
IOMMU-aware dma_alloc_attrs() implementation allocates buffers in
power-of-two chunks to improve performance and take advantage of large
page mappings provided by some IOMMU hardware. However current code, due
to a subtle bug, allocated those chunks in the smallest-to-largest
order, what completely killed all the advantages of using larger than
page chunks. If a 4KiB chunk has been mapped as a first chunk, the
consecutive chunks are not aligned correctly to the power-of-two which
match their size and IOMMU drivers were not able to use internal
mappings of size other than the 4KiB (largest common denominator of
alignment and chunk size).
This patch fixes this issue by changing to the correct largest-to-smallest
chunk size allocation sequence.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Commit f4d40de39a23f0c39cca55ac63e1175c69c3d2f7 ("net fec: do not depend
on grouped clocks") breaks compilation of the FEC driver for non iMX
platforms in linux-3.5-rc1. For example when compiling for ColdFire I get:
LD vmlinux
drivers/built-in.o: In function `fec_probe':
fec.c:(.devinit.text+0x1e0): undefined reference to `devm_clk_get'
Define a simple devm_clk_get() function for the m68knommu architecture.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas into fixes
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/renesas:
ARM: shmobile: r8a7779: Route all interrupts to ARM
ARM: shmobile: kzm9d: use late init machine hook
ARM: shmobile: kzm9g: use late init machine hook
ARM: mach-shmobile: armadillo800eva: Use late init machine hook
ARM: mach-shmobile: add missing GPIO IRQ configuration on mackerel
ARM: mach-shmobile: Fix build when SMP is enabled and EMEV2 is not enabled
ARM: shmobile: sh7372: bugfix: chclr_offset base
ARM: shmobile: sh73a0: bugfix: SY-DMAC number
|
|
Coult -> Could
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull KVM fixes from Avi Kivity:
"Fixing a scheduling-while-atomic bug in the ppc code, and a bug which
allowed pci bridges to be assigned to guests."
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Drop locks around call to kvmppc_pin_guest_page
KVM: Fix PCI header check on device assignment
|
