| Age | Commit message (Collapse) | Author |
|---|
|
This patch fix the regression introduced by the commit 3202bf0157ccb
"arm: mvebu: Improve the SMP support of the interrupt controller":
GPIO IRQ were no longer delivered to the CPUs.
To be delivered to a CPU an interrupt must be enabled at CPU level and
at interrupt source level. Before the offending patch, all the
interrupts were enabled at source level during map() function. Mask()
and unmask() was done by handling the per-CPU part. It was fine when
running in UP with only one CPU.
The offending patch added support for SMP, in this case mask() and
unmask() was done by handling the interrupt source level part. The
per-CPU level part was handled by the affinity API to select the CPU
which will receive the interrupt. (Due to some hardware limitation
only one CPU at a time can received a given interrupt).
For "normal" interrupt __setup_irq() was called when an irq was
registered. irq_set_affinity() is called from this function, which
enabled the interrupt on one of the CPUs. Whereas for GPIO IRQ which
were chained interrupts, the irq_set_affinity() was never called and
none of the CPUs was selected to receive the interrupt.
With this patch all the interrupt are enable on the current CPU during
map() function. Enabling the interrupts on a CPU doesn't depend
anymore on irq_set_affinity() and then the chained irq are not anymore
a special case. However the CPU which will receive the irq can still
be modify later using irq_set_affinity().
Tested with Mirabox (A370) and Openblocks AX3 (AXP), rootfs mounted
over NFS, compiled with CONFIG_SMP=y/N.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reported-by: Ryan Press <ryan@presslab.us>
Investigated-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
In the conversion to pinctrl, an error in the pins for the rebuild
LED was introduced. This patch assigns the correct pins and includes
the correct name for the LED in kirkwood-iomega_ix2_200.dts.
Signed-off-by: Nigel Roberts <nigel@nobiscuit.com>
Cc: <stable@vger.kernel.org> # v3.8.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The previous configuration used the wrong "clk" pin. Without this
change mv_sdio worked because the bootloader would set the pin up, but
with a bootloader that does not set the pin, mv_sdio fails to detect any
card.
I have tested this change using a mwifiex_sdio wireless network adapter
over the SDIO interface.
Signed-off-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The crypto functionality in the orion5x dtsi uses the Ethernet IRQ and
so things do not work and there is much grumbling at boot time.
The IRQ for the crypto should be 28, and not 22, and that is what this
patch corrects.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
orion5x.dtsi is missing the gpio alias as well as including a typo
('ngpio' instead of 'ngpios') that prevented the orion-gpio driver
from loading. Also missing were the interrupt-controller properties.
This patches resolves those glitches.
Signed-off-by: Alexander Clouter <alex@digriz.org.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
mvsdio_platform_data allows to pass card detect and write protect gpio
numbers to the driver. Some kirkwood boards don't use both pins as they
are not connected, and don't set the corresponding value in platform_data.
This will leave the unset values in platform_data initialized as 0, which
is in fact a valid gpio pin. mvsdio will grab that pin and configure it as
gpio, which in turn breaks nand controller as mpp0 also carries nand_io2.
This patch fixes the above by initializing unused gpio functions in the
platform_data with an invalid (-1) value.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reported-by: Soeren Moch <smoch@web.de>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The commit 3a6f08a37 "arm: mvebu: Add support for local interrupt",
managed the 28th first interrupts as local interrupt to match the
hardware specification. Among these interrupts there are the Gigabits
Ethernet ones used by the mvneta driver. Unfortunately the state of
the percpu_irq API prevents the driver to use it.
Indeed the interrupts have to be freed when the .stop() function is
called. As the free_percpu_irq() function don't disable the interrupt
line, we have to do it on each CPU before calling this. The function
disable_percpu_irq() only disable the percpu on the current CPU and
there is no function which allows to disable a percpu irq on a given
CPU. Waiting for the extension of the percpu_irq API, this fix allows
to use again the mvneta driver.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This fixes "Too few good blocks within range" issues on GoFlex Net by setting
chip-delay to 40.
The basic problem was discussed at http://forum.doozan.com/read.php?2,7451
Signed-off-by: Eric Hutter <hutter.eric@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.6.x
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.
However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two address decoding windows to the
SDRAM. However, in the device registers for the address decoding, the
base address is only 32 bits, so those two windows overlap each other,
and the devices do not work at all.
This patch makes sure that the array built by
orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows
that correspond to the first 4 GB of the memory. To do that, it
ignores the SDRAM decoding windows for which the 4 low-order bits are
not zero (the 4 low-order bits of the base register are used to store
bits 32:35 of the base address, so they actually indicate whether the
base address is above 4 GB).
This patch allows the newly introduced armada-xp-gp board to properly
operate when it is mounted with more than 4 GB of RAM. Without that,
all devices doing DMA (for example XOR and Ethernet) do not work at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Setting the reg-io-width to 1 byte represents more accurate
description of the HW.
This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The commit:
48be9ac ARM: Dove: split legacy and DT setup
removed the RTC initialization. This patch re-enables the RTC
via the DT.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Commit 5b03df9ace680d7cdd34a69dfd85ca5f74159d18 ("ARM: dove: switch to
DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's
Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which
makes this select statement a nop. It's probably a leftover of some
experimental code that never hit mainline. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The kirkwood SoC GPIO cores use the runit clock. Add code to
clk_prepare_enable() runit, otherwise there is a danger of locking up
the SoC by accessing the GPIO registers when runit clock is not
ticking.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The ethernet controller used on kirkwood looses its MAC address
register contents when the corresponding clock is gated. As soon as
mv643xx_eth is built as module, the clock gets gated and when loading
the module, the MAC address is gone.
Proper DT support for the mv643xx_eth driver is expected soon, so we add
a workaround to always enable ge0/ge1 clocks on kirkwood. This workaround
is also already used on non-DT kirkwood kernels.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
When DT support for kirkwood was first introduced, there was no clock
infrastructure. As a result, we had to manually pass the
clock-frequency to the driver from the device node.
Unfortunately, on kirkwood, with minimal config or all module configs,
clock-frequency breaks booting because of_serial doesn't consume the
gate_clk when clock-frequency is defined.
The end result on kirkwood is that runit gets gated, and then the boot
fails when the kernel tries to write to the serial port.
Fix the issue by removing the clock-frequency parameter from all
kirkwood dts files.
Booted on dreamplug without earlyprintk and successfully logged in via
ttyS0.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
- Update the Xen ACPI memory and CPU hotplug locking mechanism.
- Fix PAT issues wherein various applications would not start
- Fix handling of multiple MSI as AHCI now does it.
- Fix ARM compile failures.
* tag 'stable/for-linus-3.9-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: fix compile failure on ARM with Xen enabled
xen/pci: We don't do multiple MSI's.
xen/pat: Disable PAT using pat_enabled value.
xen/acpi: xen cpu hotplug minor updates
xen/acpi: xen memory hotplug minor updates
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull more VFS bits from Al Viro:
"Unfortunately, it looks like xattr series will have to wait until the
next cycle ;-/
This pile contains 9p cleanups and fixes (races in v9fs_fid_add()
etc), fixup for nommu breakage in shmem.c, several cleanups and a bit
more file_inode() work"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
constify path_get/path_put and fs_struct.c stuff
fix nommu breakage in shmem.c
cache the value of file_inode() in struct file
9p: if v9fs_fid_lookup() gets to asking server, it'd better have hashed dentry
9p: make sure ->lookup() adds fid to the right dentry
9p: untangle ->lookup() a bit
9p: double iput() in ->lookup() if d_materialise_unique() fails
9p: v9fs_fid_add() can't fail now
v9fs: get rid of v9fs_dentry
9p: turn fid->dlist into hlist
9p: don't bother with private lock in ->d_fsdata; dentry->d_lock will do just fine
more file_inode() open-coded instances
selinux: opened file can't have NULL or negative ->f_path.dentry
(In the meantime, the hlist traversal macros have changed, so this
required a semantic conflict fixup for the newly hlistified fid->dlist)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull second set of s390 patches from Martin Schwidefsky:
"The main part of this merge are Heikos uaccess patches. Together with
commit 09884964335e ("mm: do not grow the stack vma just because of an
overrun on preceding vma") the user string access is hopefully fixed
for good.
In addition some bug fixes and two cleanup patches."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/module: fix compile warning
qdio: remove unused parameters
s390/uaccess: fix kernel ds access for page table walk
s390/uaccess: fix strncpy_from_user string length check
input: disable i8042 PC Keyboard controller for s390
s390/dis: Fix invalid array size
s390/uaccess: remove pointless access_ok() checks
s390/uaccess: fix strncpy_from_user/strnlen_user zero maxlen case
s390/uaccess: shorten strncpy_from_user/strnlen_user
s390/dasd: fix unresponsive device after all channel paths were lost
s390/mm: ignore change bit for vmemmap
s390/page table dumper: add support for change-recording override bit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull second round of PARISC updates from Helge Deller:
"The most important fix in this branch is the switch of io_setup,
io_getevents and io_submit syscalls to use the available compat
syscalls when running 32bit userspace on 64bit kernel. Other than
that it's mostly removal of compile warnings."
* 'fixes-for-3.9-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix redefinition of SET_PERSONALITY
parisc: do not install modules when installing kernel
parisc: fix compile warnings triggered by atomic_sub(sizeof(),v)
parisc: check return value of down_interruptible() in hp_sdc_rtc.c
parisc: avoid unitialized variable warning in pa_memcpy()
parisc: remove unused variable 'compat_val'
parisc: switch to compat_functions of io_setup, io_getevents and io_submit
parisc: select ARCH_WANT_FRAME_POINTERS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull new ImgTec Meta architecture from James Hogan:
"This adds core architecture support for Imagination's Meta processor
cores, followed by some later miscellaneous arch/metag cleanups and
fixes which I kept separate to ease review:
- Support for basic Meta 1 (ATP) and Meta 2 (HTP) core architecture
- A few fixes all over, particularly for symbol prefixes
- A few privilege protection fixes
- Several cleanups (setup.c includes, split out a lot of
metag_ksyms.c)
- Fix some missing exports
- Convert hugetlb to use vm_unmapped_area()
- Copy device tree to non-init memory
- Provide dma_get_sgtable()"
* tag 'metag-v3.9-rc1-v4' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag: (61 commits)
metag: Provide dma_get_sgtable()
metag: prom.h: remove declaration of metag_dt_memblock_reserve()
metag: copy devicetree to non-init memory
metag: cleanup metag_ksyms.c includes
metag: move mm/init.c exports out of metag_ksyms.c
metag: move usercopy.c exports out of metag_ksyms.c
metag: move setup.c exports out of metag_ksyms.c
metag: move kick.c exports out of metag_ksyms.c
metag: move traps.c exports out of metag_ksyms.c
metag: move irq enable out of irqflags.h on SMP
genksyms: fix metag symbol prefix on crc symbols
metag: hugetlb: convert to vm_unmapped_area()
metag: export clear_page and copy_page
metag: export metag_code_cache_flush_all
metag: protect more non-MMU memory regions
metag: make TXPRIVEXT bits explicit
metag: kernel/setup.c: sort includes
perf: Enable building perf tools for Meta
metag: add boot time LNKGET/LNKSET check
metag: add __init to metag_cache_probe()
...
|
|
Pull late ARM updates from Russell King:
"Here is the late set of ARM updates for this merge window; in here is:
- The ARM parts of the broadcast timer support, core parts merged
through tglx's tree. This was left over from the previous merge to
allow the dependency on tglx's tree to be resolved.
- A fix to the VFP code which shows up on Raspberry Pi's, as well as
fixing the fallout from a previous commit in this area.
- A number of smaller fixes scattered throughout the ARM tree"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm:
ARM: Fix broken commit 0cc41e4a21d43 corrupting kernel messages
ARM: fix scheduling while atomic warning in alignment handling code
ARM: VFP: fix emulation of second VFP instruction
ARM: 7656/1: uImage: Error out on build of multiplatform without LOADADDR
ARM: 7640/1: memory: tegra_ahb_enable_smmu() depends on TEGRA_IOMMU_SMMU
ARM: 7654/1: Preserve L_PTE_VALID in pte_modify()
ARM: 7653/2: do not scale loops_per_jiffy when using a constant delay clock
ARM: 7651/1: remove unused smp_timer_broadcast #define
|
|
Pull watchdog updates from Wim Van Sebroeck:
"This contains:
- fixes and improvements
- devicetree bindings
- conversion to watchdog generic framework of the following drivers:
- booke_wdt
- bcm47xx_wdt.c
- at91sam9_wdt
- Removal of old STMP3xxx driver
- Addition of following new drivers:
- new driver for STMP3xxx and i.MX23/28
- Retu watchdog driver"
* git://www.linux-watchdog.org/linux-watchdog: (30 commits)
watchdog: sp805_wdt depends on ARM
watchdog: davinci_wdt: update to devm_* API
watchdog: davinci_wdt: use devm managed clk get
watchdog: at91rm9200: add DT support
watchdog: add timeout-sec property binding
watchdog: at91sam9_wdt: Convert to use the watchdog framework
watchdog: omap_wdt: Add option nowayout
watchdog: core: dt: add support for the timeout-sec dt property
watchdog: bcm47xx_wdt.c: add hard timer
watchdog: bcm47xx_wdt.c: rename wdt_time to timeout
watchdog: bcm47xx_wdt.c: rename ops methods
watchdog: bcm47xx_wdt.c: use platform device
watchdog: bcm47xx_wdt.c: convert to watchdog core api
watchdog: Convert BookE watchdog driver to watchdog infrastructure
watchdog: s3c2410_wdt: Use devm_* functions
watchdog: remove old STMP3xxx driver
watchdog: add new driver for STMP3xxx and i.MX23/28
rtc: stmp3xxx: add wdt-accessor function
watchdog: introduce retu_wdt driver
watchdog: intel_scu_watchdog: fix Kconfig dependency
...
|
|
|
|
metag/allmodconfig:
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function 'vb2_dc_get_base_sgt':
drivers/media/v4l2-core/videobuf2-dma-contig.c:387: error: implicit declaration of function 'dma_get_sgtable'
For architectures using dma_map_ops, dma_get_sgtable() is provided in
<asm-generic/dma-mapping-common.h>.
Metag does not use dma_map_ops yet, hence it should implement it as an
inline stub using dma_common_get_sgtable().
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
Metag doesn't have a metag_dt_memblock_reserve() function so remove the
declaration from asm/prom.h.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Make a copy of the device tree blob in non-init memory. It is required
when using built-in device tree files that the platform code copies the
blob to non-init memory prior to calling unflatten_device_tree(),
otherwise the strings that the device tree refer to will get poisoned
and potentially reused, breaking later reading of the device tree
post-init (such as compatible matching in modules, debugfs, and the
procfs interface).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Minimise metag_ksyms.c includes to directly include the <asm/*.h> files
that declare a particular symbol, and not include any unnecessary ones.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in mm/init.c into mm/init.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in usercopy.c into usercopy.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in setup.c into setup.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in kick.c into kick.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
It's less error prone to have function symbols exported immediately
after the function rather than in metag_ksyms.c. Move each EXPORT_SYMBOL
in metag_ksyms.c for symbols defined in traps.c into traps.c
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
The SMP version of arch_local_irq_enable() uses preempt_disable(), but
<asm/irqflags.h> doesn't include <linux/preempt.h> causing the following
errors on SMP when pstore/ftrace is enabled (caught by buildbot smp
allyesconfig):
In file included from include/linux/irqflags.h:15,
from fs/pstore/ftrace.c:16:
arch/metag/include/asm/irqflags.h: In function 'arch_local_irq_enable':
arch/metag/include/asm/irqflags.h:84: error: implicit declaration of function 'preempt_disable'
arch/metag/include/asm/irqflags.h:86: error: implicit declaration of function 'preempt_enable_no_resched'
However <linux/preempt.h> cannot be easily included from
<asm/irqflags.h> as it can cause circular include dependencies in the
!SMP case, and potentially in the SMP case in the future. Therefore move
the SMP implementation of arch_local_irq_enable() into traps.c and use
an inline version of get_trigger_mask() which is also defined in traps.c
for SMP.
This adds an extra layer of function call / stack push when
preempt_disable needs to call other functions, however in the
non-preemptive SMP case it should be about as fast, as it was already
calling the get_trigger_mask() function which is now used inline.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Convert hugetlb_get_unmapped_area_new_pmd() to use vm_unmapped_area()
rather than searching the virtual address space itself. This fixes the
following errors in linux-next due to the specified members being
removed after other architectures have already been converted:
arch/metag/mm/hugetlbpage.c: In function 'hugetlb_get_unmapped_area_new_pmd':
arch/metag/mm/hugetlbpage.c:199: error: 'struct mm_struct' has no member named 'cached_hole_size'
arch/metag/mm/hugetlbpage.c:200: error: 'struct mm_struct' has no member named 'free_area_cache'
arch/metag/mm/hugetlbpage.c:215: error: 'struct mm_struct' has no member named 'cached_hole_size'
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Michel Lespinasse <walken@google.com>
|
|
Various file systems use clear_page() and copy_page(), so when they're
built as modules we get build errors like the following:
ERROR: "clear_page" [fs/ntfs/ntfs.ko] undefined!
ERROR: "copy_page" [fs/nilfs2/nilfs2.ko] undefined!
Therefore export these functions to modules from metag_ksyms.c to fix
the errors. This was hit by a randconfig build.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Various file systems indirectly use metag_code_cache_flush_all(), so
when they're built as modules we get build errors like the following:
ERROR: "metag_code_cache_flush_all" [fs/xfs/xfs.ko] undefined!
Therefore export this function to modules to fix the errors. This was
hit by a randconfig build.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Rename setup_txprivext() to setup_priv() and add initialisation of some
more per-thread privilege protection registers:
- TxPRIVSYSR: 0x04400000-0x047fffff
0x05000000-0x07ffffff
0x84000000-0x87ffffff
- TxPIOREG: 0x02000000-0x02ffffff
0x04800000-0x048fffff
- TxSYREG: 0x04000000-0x04000fff (except write fetch system event)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Define PRIV_BITS using explicit constants from <asm/metag_regs.h> rather
than with a hard coded value. This also adds a couple of missing
definitions for the TXPRIVEXT priv bits for protecting writes to TXTIMER
and the trace registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Sort includes in kernel/setup.c.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Add boot time check for whether LNKGET/LNKSET go through or around the
cache. Depending on the configuration an info message (no harm), warning
(technically wrong but no harm), or big WARN (expect failure in either
kernel or userland) may be emitted if the behaviour is not as expected:
Configuration Hardware Response
------------------------------------------ -------- --------
AROUND_CACHE through pr_info
!AROUND_CACHE && ATOMICITY_LNKGET around WARN (kernel)
" && !ATOMICITY_LNKGET && SMP around WARN (user)
" " && !SMP around pr_warn
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
metag_cache_probe() is only called from setup_arch(), so add the __init
attribute to it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Add basic JTAG Debug Adapter (DA) support so that drivers which
communicate with the DA can detect whether one is actually present
(otherwise the target will halt indefinitely).
This allows the metag_da TTY driver and imgdafs filesystem driver to be
built, updates defconfigs, and sets up the metag_da console early if
it's configured in.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
|
Add ftrace support for metag.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Add Perf support for metag.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
|
|
Add metag build infrastructure.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
|
