Age | Commit message (Collapse) | Author |
|
|
|
As noted in 83d349f35e1ae72268c5104dbf9ab2ae635425d4 ("x86: don't send
an IPI to the empty set of CPU's"), some APIC's will be very unhappy
with an empty destination mask. That commit added a WARN_ON() for that
case, and avoided the resulting problem, but didn't fix the underlying
reason for why those empty mask cases happened.
This fixes that, by checking the result of 'cpumask_andnot()' of the
current CPU actually has any other CPU's left in the set of CPU's to be
sent a TLB flush, and not calling down to the IPI code if the mask is
empty.
The reason this started happening at all is that we started passing just
the CPU mask pointers around in commit 4595f9620 ("x86: change
flush_tlb_others to take a const struct cpumask"), and when we did that,
the cpumask was no longer thread-local.
Before that commit, flush_tlb_mm() used to create it's own copy of
'mm->cpu_vm_mask' and pass that copy down to the low-level flush
routines after having tested that it was not empty. But after changing
it to just pass down the CPU mask pointer, the lower level TLB flush
routines would now get a pointer to that 'mm->cpu_vm_mask', and that
could still change - and become empty - after the test due to other
CPU's having flushed their own TLB's.
See
http://bugzilla.kernel.org/show_bug.cgi?id=13933
for details.
Tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The default_send_IPI_mask_logical() function uses the "flat" APIC mode
to send an IPI to a set of CPU's at once, but if that set happens to be
empty, some older local APIC's will apparently be rather unhappy. So
just warn if a caller gives us an empty mask, and ignore it.
This fixes a regression in 2.6.30.x, due to commit 4595f9620 ("x86:
change flush_tlb_others to take a const struct cpumask"), documented
here:
http://bugzilla.kernel.org/show_bug.cgi?id=13933
which causes a silent lock-up. It only seems to happen on PPro, P2, P3
and Athlon XP cores. Most developers sadly (or not so sadly, if you're
a developer..) have more modern CPU's. Also, on x86-64 we don't use the
flat APIC mode, so it would never trigger there even if the APIC didn't
like sending an empty IPI mask.
Reported-by: Pavel Vilim <wylda@volny.cz>
Reported-and-tested-by: Thomas Björnell <thomas.bjornell@gmail.com>
Reported-and-tested-by: Martin Rogge <marogge@onlinehome.de>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Update Microblaze defconfigs
microblaze: Use klimit instead of _end for memory init
microblaze: Enable ppoll syscall
microblaze: Sane handling of missing timer/intc in device tree
microblaze: use the generic ack_bad_irq implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: use the right flag for get_vm_area()
percpu, sparc64: fix sparse possible cpu map handling
init: set nr_cpu_ids before setup_per_cpu_areas()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: Don't initialize MCEs on unknown CPUs
x86, mce: don't log boot MCEs on Pentium M (model == 13) CPUs
x86: Annotate section mismatch warnings in kernel/apic/x2apic_uv_x.c
x86, mce: therm_throt: Don't log redundant normality
x86: Fix UV BAU destination subnode id
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: sh7724 ddr self-refresh changes
sh: use in-soc KEYSC on se7724
sh: CMT suspend/resume
sh: skip disabled LCDC channels
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
For noMMU system when you use larger rootfs image
there is problem with using _end label because
we increase klimit but in memory initialization
we use still _end which is wrong. Larger mtd rootfs
was rewritten by init_bootmem_node.
MMU kernel use static initialization where klimit
is setup to _end. There is no any other hanling
with klimit.
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
This code path doesn't test any returned pointers for NULL, leading to a bad
kernel page fault if there's no timer/intc found.
Slightly better is to BUG(), but even better still would be a printk beforehand.
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Michal Simek <monstr@monstr.eu>
|
|
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: Fix HPAGE_SIZE redefinition
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm: (37 commits)
ARM: 5673/1: U300 fix initsection compile warning
ARM: Fix broken highmem support
mx31moboard: invert sdhc ro signal sense
ARM: S3C24XX: Fix clkout mpx error
ARM: S3C64XX: serial: Fix a typo in Kconfig
IXP4xx: Fix IO_SPACE_LIMIT for 2.6.31-rc core PCI changes
OMAP3: RX51: Updated rx51_defconfig
OMAP2/3: mmc-twl4030: Free up MMC regulators while cleaning up
OMAP3: RX51: Define TWL4030 USB transceiver in board file
OMAP3: Overo: Fix smsc911x platform device resource value
OMAP3: Fix omap3 sram virtual addres overlap vmalloc space after increasing vmalloc size
OMAP2/3: DMA errata correction
OMAP: Fix testing of cpu defines for mach-omap1
OMAP3: Overo: add missing pen-down GPIO definition
OMAP: GPIO: clear/restore level/edge detect settings on mask/unmask
OMAP3: PM: Fix wrong sequence in suspend.
OMAP: PM: CPUfreq: obey min/max settings of policy
OMAP2/3/4: UART: allow in-order port traversal
OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports
OMAP3: Fixed crash bug with serial + suspend
...
|
|
This patch fixes warnings like this:
CC fs/proc/meminfo.o
In file included from /work/linux/include/linux/mmzone.h:20,
from /work/linux/include/linux/gfp.h:4,
from /work/linux/include/linux/mm.h:8,
from /work/linux/fs/proc/meminfo.c:5:
/work/linux/arch/mips/include/asm/page.h:36:1: warning: "HPAGE_SIZE" redefined
In file included from /work/linux/fs/proc/meminfo.c:2:
/work/linux/include/linux/hugetlb.h:107:1: warning: this is the location of the previous definition
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
An older test-box started hanging at the following point during
bootup:
[ 0.022996] Mount-cache hash table entries: 512
[ 0.024996] Initializing cgroup subsys debug
[ 0.025996] Initializing cgroup subsys cpuacct
[ 0.026995] Initializing cgroup subsys devices
[ 0.027995] Initializing cgroup subsys freezer
[ 0.028995] mce: CPU supports 5 MCE banks
I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit
machine check code on 32bit"), which utilizes the MCE code on
32-bit systems too.
The problem is caused by this detail in my config:
# CONFIG_CPU_SUP_INTEL is not set
This disables the quirks in mce_cpu_quirks() but still enables
MCE support - which then hangs due to the missing quirk
workaround needed on this CPU:
if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0)
mce_banks[0].init = 0;
The safe solution is to not initialize MCEs if we dont know on
what CPU we are running (or if that CPU's support code got
disabled in the config).
Also be a bit more defensive on 32-bit systems: dont do a
boot-time dump of pending MCEs not just on the specific system
that we found a problem with (Pentium-M), but earlier ones as
well.
Now this problem is probably not common and disabling CPU
support is rare - but still being more defensive in something
we turned on for a wide range of CPUs is prudent.
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold
boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog):
MCE 0
HARDWARE ERROR. This is *NOT* a software problem!
Please contact your hardware vendor
CPU 0 BANK 1 MCG status:
MCi status:
Error overflow
Uncorrected error
Error enabled
Processor context corrupt
MCA: Data CACHE Level-1 UNKNOWN Error
STATUS f200000000000195 MCGSTATUS 0
[ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error)
and f200000000000115 (... READ Error).
To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified
the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump
content of STATUS MSR before it is cleared during initialization. ]
Since the bogus MCE results in a kernel taint (which in turn disables
lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs
by default ("mce=bootlog" boot parameter can be be used to get the old
behavior).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The function uv_acpi_madt_oem_check() has been marked __init,
the struct apic_x2apic_uv_x has been marked __refdata.
The aim is to address the following section mismatch messages:
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap()
The function uv_acpi_madt_oem_check() references
the function __init early_ioremap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_ioremap is wrong.
WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap()
The function uv_acpi_madt_oem_check() references
the function __init early_iounmap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_iounmap is wrong.
WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
LKML-Reference: <200908161855.48302.lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
0d01f31439c1e4d602bf9fdc924ab66f407f5e38 "x86, mce: therm_throt
- change when we print messages" removed redundant
announcements of "Temperature/speed normal".
They're not worth logging and remove their accompanying
"Machine check events logged" messages as well from the
console.
Signed-off-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
LKML-Reference: <Pine.LNX.4.64.0908161544100.7929@sister.anvils>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The u300_init_check_chip() function was not properly tagged with
the __init macro and provided a initsection mismatch on
compilation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
|
|
Currently, highmem is selectable, and you can request an increased
vmalloc area. However, none of this has any effect on the memory
layout since a patch in the highmem series was accidentally dropped.
Moreover, even if you did want highmem, all memory would still be
registered as lowmem, possibly resulting in overflow of the available
virtual mapping space.
The highmem boundary is determined by the highest allowed beginning
of the vmalloc area, which depends on its configurable minimum size
(see commit 60296c71f6c5063e3c1f1d2619ca0b60940162e7 for details on
this).
We should create mappings and initialize bootmem only for low memory,
while the zone allocator must still be told about highmem.
Currently, memory nodes which are completely located in high memory
are not supported. This is not a huge limitation since systems
relying on highmem support are unlikely to have discontiguous memory
with large holes.
[ A similar patch was meant to be merged before commit 5f0fbf9ecaf3
and be available in Linux v2.6.30, however some git rebase screw-up
of mine dropped the first commit of the series, and that goofage
escaped testing somehow as well. -- Nico ]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
|
|
The SGI UV Broadcast Assist Unit is used to send TLB shootdown
messages to remote nodes of the system. The header of the
message must contain the subnode id of the block in the
receiving hub that handles such messages. It should always be
0x10, the id of the "LB" block.
It had previously been documented as a "must be zero" field.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <E1Mc1x7-0005Ce-6t@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch updates the SuperH Mobile sleep assembly code with
support for DBSC memory controller found in the sh7724 processor.
Without this fix the memory hooked up to the sh7724 processor
will never enter self-refresh mode before suspending to ram. The
effect of this is that the memory contents most likeley will be
lost upon resume which may or may not be what you want.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.
Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.
Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Small confusion with our hardware engineer, the WP signal (RO) is
active low on our boards, the signal has to inverted.
This is a pretty straightforward patch, it could even go to -rc,
but if not, then push it for 2.6.32.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
percpu code has been assuming num_possible_cpus() == nr_cpu_ids which
is incorrect if cpu_possible_map contains holes. This causes percpu
code to access beyond allocated memories and vmalloc areas. On a
sparc64 machine with cpus 0 and 2 (u60), this triggers the following
warning or fails boot.
WARNING: at /devel/tj/os/work/mm/vmalloc.c:106 vmap_page_range_noflush+0x1f0/0x240()
Modules linked in:
Call Trace:
[00000000004b17d0] vmap_page_range_noflush+0x1f0/0x240
[00000000004b1840] map_vm_area+0x20/0x60
[00000000004b1950] __vmalloc_area_node+0xd0/0x160
[0000000000593434] deflate_init+0x14/0xe0
[0000000000583b94] __crypto_alloc_tfm+0xd4/0x1e0
[00000000005844f0] crypto_alloc_base+0x50/0xa0
[000000000058b898] alg_test_comp+0x18/0x80
[000000000058dad4] alg_test+0x54/0x180
[000000000058af00] cryptomgr_test+0x40/0x60
[0000000000473098] kthread+0x58/0x80
[000000000042b590] kernel_thread+0x30/0x60
[0000000000472fd0] kthreadd+0xf0/0x160
---[ end trace 429b268a213317ba ]---
This patch fixes generic percpu functions and sparc64
setup_per_cpu_areas() so that they handle sparse cpu_possible_map
properly.
Please note that on x86, cpu_possible_map() doesn't contain holes and
thus num_possible_cpus() == nr_cpu_ids and this patch doesn't cause
any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
|
|
Bug correction: CLK Outputs cannot have XTAL as parent
Signed-off-by: Davide Rizzo <elpa.rizzo@gmail.com>
[ben-linux@fluff.org: updated patch subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Report the cloning task as parent on perf_counter_fork()
perf_counter: Fix an ipi-deadlock
perf: Rework/fix the whole read vs group stuff
perf_counter: Fix swcounter context invariance
perf report: Don't show unresolved DSOs and symbols when -S/-d is used
perf tools: Add a general option to enable raw sample records
perf tools: Add a per tracepoint counter attribute to get raw sample
perf_counter: Provide hw_perf_counter_setup_online() APIs
perf list: Fix large list output by using the pager
perf_counter, x86: Fix/improve apic fallback
perf record: Add missing -C option support for specifying profile cpu
perf tools: Fix dso__new handle() to handle deleted DSOs
perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available
perf report: Show the tid too in -D
perf record: Fix .tid and .pid fill-in when synthesizing events
perf_counter, x86: Fix generic cache events on P6-mobile CPUs
perf_counter, x86: Fix lapic printk message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix oops in identify_cpu() on CPUs without CPUID
x86: Clear incorrectly forced X86_FEATURE_LAHF_LM flag
x86, mce: therm_throt - change when we print messages
x86: Add reboot quirk for every 5 series MacBook/Pro
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chris/linux-2.6
|
|
Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Johannes Stezenbach reported that his Pentium-M based
laptop does not have the local APIC enabled by default,
and hence perfcounters do not get initialized.
Add a fallback for this case: allow non-sampled counters
and return with an error on sampled counters. This allows
'perf stat' to work out of box - and allows 'perf top'
and 'perf record' to fall back on a hrtimer based sampling
method.
( Passing 'lapic' on the boot line will allow hardware
sampling to occur - but if the APIC is disabled
permanently by the hardware then this fallback still
allows more systems to use perfcounters. )
Also decouple perfcounter support from X86_LOCAL_APIC.
-v2: fix typo breaking counters on all other systems ...
Reported-by: Johannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Kernel is broken for x86 CPUs without CPUID since 2.6.28. It
crashes with NULL pointer dereference in identify_cpu():
766 generic_identify(c);
767
768--> if (this_cpu->c_identify)
769 this_cpu->c_identify(c);
this_cpu is NULL. This is because it's only initialized in
get_cpu_vendor() function, which is not called if the CPU has
no CPUID instruction.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
LKML-Reference: <200908112000.15993.linux@rainbow-software.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Missing test after ioremap()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
|
|
Make cache_add_dev exit sysfs when kobject_init_and_add returns an error.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
|
|
Between GCC version 3.4.0 and 4.3.3 (including 3.4.0 and 4.3.3), -mtune=merced
is implemented in GCC. Starting from 4.4.0, -mtune=merced is deprecated.
Even implemented in versions between 3.4.0 and 4.3.3, the -mtune=merced
feature has been broken in some of the versions. For example, GCC 4.1.2 reports
interanl tuning function errors during kernel building with -mtune=merced. Or
GCC Bugzilla 16130 reports another -mtune=merced issue on GCC 3.4.1.
So I would remove the -mtune=merced from IA64 kernel build. Without this option,
kernel on Merced will remain the same except losing an unstable and out-of-date
performance tunning feature.
Since GCC version 3.4.0, -mtune=mckinley has been implemented. The
-mtune=mckinley option functions the same as mtune=itanium2. And mtune=itanium2
is the default option. So we don't need to add mtune=mckinley either since its
been the default option in any GCC version which implements this option.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
|
|
fix the following 'make includecheck' warning:
arch/ia64/include/asm/pgtable.h: asm/processor.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
|
|
fix the following 'make includecheck' warning:
arch/ia64/kernel/ia64_ksyms.c: asm/page.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
|
|
__test_and_clear_bit() returns a bitfield with the tested-for bit set.
Make it consistent with the other bitops - of ia64 but also every
other architecture - and return a boolean value.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
|
|
iommu_dma_supported()
In commit 160c1d8e40866edfeae7d68816b7005d70acf391,
dma_ops->dma_supported = iommu_dma_supported;
This dma_ops->dma_supported is first called in platform_dma_init() during kernel
boot. Then dma_ops->dma_supported will be called recursively in
iommu_dma_supported.
Kernel can not boot because kernel can not get out of iommu_dma_supported until
it runs out of stack memory.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
|
|
2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata
driver doesn't find the PCI IDE controller any more. 2.6.30 was fine.
I traced this to a PCI update (1f82de10d6b1d845155363c895c552e61b36b51a)
in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and
2.6.30-git19 illustrates the breakage:
> --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200
> +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200
> @@ -26,6 +26,13 @@
> pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:02.2: PME# disabled
> PCI: bus0: Fast back to back transfers disabled
> +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> bio: create slab <bio-0> at 0
> SCSI subsystem initialized
> NET: Registered protocol family 2
> @@ -44,11 +51,7 @@
> console [ttyS0] enabled
> serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
> Driver 'sd' needs updating - please use bus_type methods
> -PCI: enabling device 0000:00:01.0 (0140 -> 0141)
> -scsi0 : pata_artop
> -scsi1 : pata_artop
> -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28
> -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28
> +pata_artop 0000:00:01.0: no available native port
> Using configured DiskOnChip probe address 0x50000000
> DiskOnChip found at 0x50000000
> NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit)
The specific change in 1f82de10d6b1d845155363c895c552e61b36b51a responsible
for this failure turned out to be the following:
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
> res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN;
> if (type == pci_bar_io) {
> l &= PCI_BASE_ADDRESS_IO_MASK;
> - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff;
> + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT;
> } else {
> l &= PCI_BASE_ADDRESS_MEM_MASK;
> mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one
bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx
defines it as 0xffff0000, which is now causing the PCI failures.
Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT
should be 0x0000ffff. This patch makes that change, which fixes the PCI
failures on my ixp4xx box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
|
|
Due to an erratum with certain AMD Athlon 64 processors, the
BIOS may need to force enable the LAHF_LM capability.
Unfortunately, in at least one case, the BIOS does this even
for processors that do not support the functionality.
Add a specific check that will clear the feature bit for
processors known not to support the LAHF/SAHF instructions.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
LKML-Reference: <4A80A5AD.2000209@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Johannes Stezenbach reported that 'perf stat' does not count
cache-miss and cache-references events on his Pentium-M based
laptop.
This is because we left them blank in p6_perfmon_event_map[],
fill them in.
Reported-by: Johannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Instead of this garbled bootup on UP Pentium-M systems:
[ 0.015048] Performance Counters:
[ 0.016004] no Local APIC, try rebooting with lapicno PMU driver, software counters only.
Print:
[ 0.015050] Performance Counters:
[ 0.016004] no APIC, boot with the "lapic" boot parameter to force-enable it.
[ 0.017003] no PMU driver, software counters only.
Cf: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
My Latitude d630 seems to be handling thermal events in SMI by
lowering the max frequency of the CPU till it cools down but
still leaks the "everything is normal" events.
This spams the console and with high priority printks.
Adjust therm_throt driver to only print messages about the fact
that temperatire returned back to normal when leaving the
throttling state.
Also lower the severity of "back to normal" message from
KERN_CRIT to KERN_INFO.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5)
too. It seems all unibody MacBook and MacBookPro require
PCI reboot handling, i guess.
Following model/machine ID list shows unibody MacBook/Pro have
the 5 series of model number:
http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.html
Signed-off-by: Shunichi Fuji <palglowr@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|