| Age | Commit message (Collapse) | Author |
|---|
|
Atomic pool should always be allocated from DMA zone if such zone is
available in the system to avoid issues caused by limited dma mask of
any of the devices used for making an atomic allocation.
Reported-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Stable <stable@vger.kernel.org> [v3.6+]
|
|
In the UAPI header files, __BIG_ENDIAN and __LITTLE_ENDIAN must be
compared against __BYTE_ORDER in preprocessor conditionals where these are
exposed to userspace (that is they're not inside __KERNEL__ conditionals).
However, in the main kernel the norm is to check for
"defined(__XXX_ENDIAN)" rather than comparing against __BYTE_ORDER and
this has incorrectly leaked into the userspace headers.
The definition of struct stat64 in M32R's asm/stat.h is wrong in this way.
Note that userspace will likely interpret the field order incorrectly as
the big-endian variant on little-endian machines - depending on header
inclusion order.
[!!!] NOTE [!!!] This patch may adversely change the userspace API. It might
be better to fix the ordering of st_blocks and __pad4 in struct stat64.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There was only chip enable and readdy/busy pins for the nand controller.
This add the rest of the pins.
pinctrl_nand_16bits contains the specific muxes for 16 bits NANDs.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Comments on NAND pins where inverted.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
The OpenRISC arch doesn't actually have the virt_to_bus methods
Signed-off-by: Jonas Bonn <jonas@southpole.se>
|
|
The recent move to GPIO descriptors breaks the OpenRISC build. Requiring
gpiolib resolves this; using gpiolib exclusively is also the recommended
way forward for all arches by the developers working on these GPIO changes.
The non-gpiolib implementation for OpenRISC never worked anyway...
Signed-off-by: Jonas Bonn <jonas@southpole.se>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen fixes from Konrad Rzeszutek Wilk:
- Compile warnings and errors (one on x86, two on ARM)
- WARNING in xen-pciback
- Use the acpi_processor_get_performance_info instead of the 'register'
version
* tag 'stable/for-linus-3.9-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/acpi: remove redundant acpi/acpi_drivers.h include
xen: arm: mandate EABI and use generic atomic operations.
acpi: Export the acpi_processor_get_performance_info
xen/pciback: Don't disable a PCI device that is already disabled.
|
|
Fix regression introduced by commit d2323cf773 ("onewire: w1-gpio: add
ext_pullup_enable pin in platform data") which added a gpio entry to the
platform data, but did not add the required initialisers to the board
files using it. Consequently, the driver would request gpio 0 at probe,
which could break other uses of the corresponding pin.
On AT91 requesting gpio 0 changes the pin muxing for PIOA0, which, for
instance, breaks SPI0 on at91sam9g20.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 5ac47f7a6efb (powerpc: Relocate prom_init.c on 64bit) made
prom_init.c position independent by manually relocating its entries
in the TOC.
We get the address of the TOC entries with the __prom_init_toc_start
linker symbol. If __prom_init_toc_start ends up as an entry in the
TOC then we need to add an offset to get the current address. This is
the case for older toolchains.
On the other hand, if we have a newer toolchain that supports
-mcmodel=medium then __prom_init_toc_start will be created by a
relative offset from r2 (the TOC pointer). Since r2 has already been
relocated, nothing more needs to be done. Adding an offset in this
case is wrong and Aaro Koskinen and Alexander Graf have noticed noticed
G5 and OpenBIOS breakage.
Alan Modra suggested we just use r2 to get at the TOC which is simpler
and works with both old and new toolchains.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Anton Blanchard <anton@samba.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
The Kconfig symbol POWER4_ONLY got removed in commit
694caf0255dcab506d1e174c96a65ab65d96e108 ("powerpc: Remove
CONFIG_POWER4_ONLY"). Remove its last traces.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Commit 44ae3ab3358e962039c36ad4ae461ae9fb29596c forgot to update
the entry for the 970MP rev 1.0 processor when moving some CPU
features bits to the MMU feature bit mask. This breaks booting
on some rare G5 models using that chip revision.
Reported-by: Phileas Fogg <phileas-fogg@mail.ru>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.0+]
|
|
Commit f5339277eb8d3aed37f12a27988366f68ab68930 accidentally removed
more than just iSeries bits and took out the call to stab_initialize()
thus breaking support for POWER3 processors.
Put it back. (Yes, nobody noticed until now ...)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org> [v3.4+]
|
|
In commit 887cbce0adea ("arch Kconfig: centralise ARCH_NO_VIRT_TO_BUS")
I introduced the config sybmol HAVE_VIRT_TO_BUS and selected that where
needed. I am not sure what I was thinking. Instead, just directly
select VIRT_TO_BUS where it is needed.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM SoC fixes from Arnd Bergmann:
"These bug fixes are for the largest part for mvebu/kirkwood, which saw
a few regressions after the clock infrastructure was enabled, and for
OMAP, which showed a few more preexisting bugs with the new
multiplatform support.
Other small fixes are for imx, mxs, tegra, spear and socfpga"
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: spear3xx: Use correct pl080 header file
Arm: socfpga: pl330: Add #dma-cells for generic dma binding support
ARM: multiplatform: Sort the max gpio numbers.
ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART"
ARM: imx: pll1_sys should be an initial on clk
arm: mach-orion5x: fix typo in compatible string of a .dts file
arm: mvebu: fix address-cells in mpic DT node
arm: plat-orion: fix address decoding when > 4GB is used
arm: mvebu: Reduce reg-io-width with UARTs
ARM: Dove: add RTC device node
arm: mvebu: enable the USB ports on Armada 370 Reference Design board
ARM: dove: drop "select COMMON_CLK_DOVE"
rtc: rtc-mv: Add support for clk to avoid lockups
gpio: mvebu: Add clk support to prevent lockup
ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
ARM: mxs: cfa10049: Fix fb initialisation function
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: OMAP: RX-51: add missing USB phy binding
clk: Tegra: Remove duplicate smp_twd clock
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68knommu fixes from Greg Ungerer:
"It contains a few small fixes for the non-MMU m68k platforms. Fixes
some compilation problems, some broken header definitions, removes an
unused config option and adds a name for the old 68000 CPU support."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: drop "select EMAC_INC"
m68knommu: fix misnamed GPIO pin definition for ColdFire 528x CPU
m68knommu: fix MC68328.h defines
m68knommu: fix build when CPU is not coldfire
m68knommu: add CPU_NAME for 68000
|
|
k is u32 which never < 0, need type cast, or cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mircea Gherzan <mgherzan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
Via Sekhar Nori <nsekhar@ti.com>:
This patch fixes a boot breakage on DA830
that was introduced with EDMA DMA engine
conversion. The bug has been there since
v3.7 and has been marked for stable update.
* tag 'davinci-for-v3.9-rc/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: edma: fix dmaengine induced null pointer dereference on da830
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Commit 455bd4c430b0 ("ARM: 7668/1: fix memset-related crashes caused by
recent GCC (4.7.2) optimizations") attempted to fix a compliance issue
with the memset return value. However the memset itself became broken
by that patch for misaligned pointers.
This fixes the above by branching over the entry code from the
misaligned fixup code to avoid reloading the original pointer.
Also, because the function entry alignment is wrong in the Thumb mode
compilation, that fixup code is moved to the end.
While at it, the entry instructions are slightly reworked to help dual
issue pipelines.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This adds additional error checking to the private edma api implementation
to catch the case where the edma_alloc_slot() has an invalid controller
parameter. The edma dmaengine wrapper driver relies on this condition
being handled in order to avoid setting up a second edma dmaengine
instance on DA830.
Verfied using a DA850 with the second EDMA controller platform instance
removed to simulate a DA830 which only has a single EDMA controller.
Reported-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Matt Porter <mporter@ti.com>
Cc: stable@vger.kernel.org # v3.7.x+
Tested-by: Tomas Novotny <tomas@novotny.cz>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
The definitions have move around recently, causing build errors
in spear3xx for all configurations:
spear3xx.c:47:5: error: 'PL080_BSIZE_16' undeclared here (not in a function)
spear3xx.c:47:23: error: 'PL080_CONTROL_SB_SIZE_SHIFT' undeclared here (not in a function)
spear3xx.c:48:22: error: 'PL080_CONTROL_DB_SIZE_SHIFT' undeclared here (not in a function)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alessandro Rubini <rubini@gnudd.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The ab8500 device is a child of the prcmu device, which is a memory mapped
bus device, whose children are addressable using physical memory addresses,
not using mailboxes, so a mailbox number in the ab8500 node cannot be
parsed by DT. Nothing uses this number, since it was only introduced
as part of the failed attempt to clean up prcmu mailbox handling, and
we can simply remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds #dma-cells property to PL330 DMA controller nodes for
supporting generic dma dt bindings on SOCFPGA platform. #dma-channels
and #dma-requests are not required now but added in advance.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.infradead.org/users/jcooper/linux into fixes
mvebu fixes for v3.9 from Jason Cooper <jason@lakedaemon.net>:
The first four patches:
89c58c1 rtc: rtc-mv: Add support for clk to avoid lockups
de88747 gpio: mvebu: Add clk support to prevent lockup
7bf5b40 ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
93fff4c ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
are Cc'd to stable since they were held over from the previous merge window.
The rest are a small collection of fixes and a couple of devicetree conversion
catchups.
* tag 'mvebu_fixes_for_v3.9' of git://git.infradead.org/users/jcooper/linux:
arm: mach-orion5x: fix typo in compatible string of a .dts file
arm: mvebu: fix address-cells in mpic DT node
arm: plat-orion: fix address decoding when > 4GB is used
arm: mvebu: Reduce reg-io-width with UARTs
ARM: Dove: add RTC device node
arm: mvebu: enable the USB ports on Armada 370 Reference Design board
ARM: dove: drop "select COMMON_CLK_DOVE"
rtc: rtc-mv: Add support for clk to avoid lockups
gpio: mvebu: Add clk support to prevent lockup
ARM: kirkwood: fix to retain gbe MAC addresses for DT kernels
ARM: kirkwood: of_serial: fix clock gating by removing clock-frequency
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The 2nd take of imx fixes for 3.9:
- Fix pll1_sys clk initial status
- Fix a typo in imx DEBUG_LL Kconfig
* tag 'imx-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx: fix typo "DEBUG_IMX50_IMX53_UART"
ARM: imx: pll1_sys should be an initial on clk
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo <shawn.guo@linaro.org>:
The 2nd mxs fixes for 3.9:
- Fix an error caused by incorrect conflict resolution when
applying the patch
* tag 'mxs-fixes-3.9-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: mxs: cfa10049: Fix fb initialisation function
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When building a multiplatform kernel, we could end up with a smaller
number of GPIOs than the one required by the platform the kernel was
running on.
Sort the max GPIO number by descending order so that we always take the
highest number required.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Rob Herring has observed that c81611c4e96f "xen: event channel arrays are
xen_ulong_t and not unsigned long" introduced a compile failure when building
without CONFIG_AEABI:
/tmp/ccJaIZOW.s: Assembler messages:
/tmp/ccJaIZOW.s:831: Error: even register required -- `ldrexd r5,r6,[r4]'
Will Deacon pointed out that this is because OABI does not require even base
registers for 64-bit values. We can avoid this by simply using the existing
atomic64_xchg operation and the same containerof trick as used by the cmpxchg
macros. However since this code is used on memory which is shared with the
hypervisor we require proper atomic instructions and cannot use the generic
atomic64 callbacks (which are based on spinlocks), therefore add a dependency
on !GENERIC_ATOMIC64. Since we already depend on !CPU_V6 there isn't much
downside to this.
While thinking about this we also observed that OABI has different struct
alignment requirements to EABI, which is a problem for hypercall argument
structs which are shared with the hypervisor and which must be in EABI layout.
Since I don't expect people to want to run OABI kernels on Xen depend on
CONFIG_AEABI explicitly too (although it also happens to be enforced by the
!GENERIC_ATOMIC64 requirement too).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <robherring2@gmail.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Misc minor fixes mostly related to tracing"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
s390: Fix a header dependencies related build error
tracing: update documentation of snapshot utility
tracing: Do not return EINVAL in snapshot when not allocated
tracing: Add help of snapshot feature when snapshot is empty
ftrace: Update the kconfig for DYNAMIC_FTRACE
|
|
Commit f8c95fe (ARM: imx: support DEBUG_LL uart port selection for all
i.MX SoCs) had a typo that DEBUG_IMX50_IMX53_UART should be
DEBUG_IMX53_UART.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
The following patch adds support for correctly
recognizing SPARC-X chips.
cpu : Unknown SUN4V CPU
fpu : Unknown SUN4V FPU
pmu : Unknown SUN4V PMU
Signed-off-by: Katayama Yoshihiro <kata1@jp.fujitsu.com>
Signed-off-by: Allen Pais <allen.pais@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 877c685607925238e302cd3aa38788dca6c1b226
("perf: Remove include of cgroup.h from perf_event.h") caused
this build failure if PERF_EVENTS is enabled:
In file included from arch/s390/include/asm/perf_event.h:9:0,
from include/linux/perf_event.h:24,
from kernel/events/ring_buffer.c:12:
arch/s390/include/asm/cpu_mf.h: In function 'qctri':
arch/s390/include/asm/cpu_mf.h:61:12: error: 'EINVAL' undeclared (first use in this function)
cpu_mf.h had an implicit errno.h dependency, which was added
indirectly via cgroups.h but not anymore. Add it explicitly.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Link: http://lkml.kernel.org/r/51385F79.7000106@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The tty below tty_port might get destroyed by the tty layer
while we hold a reference to it.
So we have to carry tty_port around...
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
As we setup the SIGWINCH handler in tty_port_operations->activate
it makes sense to tear down it in ->destruct.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
arch/um/os-Linux/signal.c:18:8: error: conflicting types for 'sig_info'
In file included from /home/slyfox/linux-2.6/arch/um/os-Linux/signal.c:12:0:
arch/um/include/shared/as-layout.h:64:15: note: previous declaration of 'sig_info' was here
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
CC: Jeff Dike <jdike@addtoit.com>
CC: Richard Weinberger <richard@nod.at>
CC: "Martin Pärtel" <martin.partel@gmail.com>
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: user-mode-linux-devel@lists.sourceforge.net
CC: user-mode-linux-user@lists.sourceforge.net
CC: linux-kernel@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
arch/um/os-Linux/start_up.c: In function 'check_coredump_limit':
arch/um/os-Linux/start_up.c:338:16: error: storage size of 'lim' isn't known
arch/um/os-Linux/start_up.c:339:2: error: implicit declaration of function 'getrlimit' [-Werror=implicit-function-declaration]
Signed-off-by: Sergei Trofimovich <slyfox@gentoo.org>
CC: Jeff Dike <jdike@addtoit.com>
CC: Richard Weinberger <richard@nod.at>
CC: Al Viro <viro@zeniv.linux.org.uk>
CC: user-mode-linux-devel@lists.sourceforge.net
CC: user-mode-linux-user@lists.sourceforge.net
CC: linux-kernel@vger.kernel.org
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This new version moves the skb_tx_timestamp in the main uml
driver. This should avoid the need to call this function in each
transport (vde, slirp, tuntap, ...). It also add support for ethtool
get_ts_info.
Signed-off-by: Paul Chavent <paul.chavent@onera.fr>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
We always boot from PLL1, so let's have pll1_sys in the clks_init_on
list to have clk prepare/enable use count match the hardware status,
so that drivers managing pll1_sys like cpufreq can get the use count
right from the start.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull namespace bugfixes from Eric Biederman:
"This is three simple fixes against 3.9-rc1. I have tested each of
these fixes and verified they work correctly.
The userns oops in key_change_session_keyring and the BUG_ON triggered
by proc_ns_follow_link were found by Dave Jones.
I am including the enhancement for mount to only trigger requests of
filesystem modules here instead of delaying this for the 3.10 merge
window because it is both trivial and the kind of change that tends to
bit-rot if left untouched for two months."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use nd_jump_link in proc_ns_follow_link
fs: Limit sys_mount to only request filesystem modules (Part 2).
fs: Limit sys_mount to only request filesystem modules.
userns: Stop oopsing in key_change_session_keyring
|
|
Merge misc fixes from Andrew Morton.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
alpha: boot: fix build breakage introduced by system.h disintegration
memcg: initialize kmem-cache destroying work earlier
Randy has moved
ksm: fix m68k build: only NUMA needs pfn_to_nid
dmi_scan: fix missing check for _DMI_ signature in smbios_present()
Revert parts of "hlist: drop the node parameter from iterators"
idr: remove WARN_ON_ONCE() on negative IDs
mm/mempolicy.c: fix sp_node_init() argument ordering
mm/mempolicy.c: fix wrong sp_node insertion
ipc: don't allocate a copy larger than max
ipc: fix potential oops when src msg > 4k w/ MSG_COPY
|
|
Commit ec2212088c42 ("Disintegrate asm/system.h for Alpha") removed the
system.h include from boot/head.S, which puts the PAL_* asm constants
out of scope.
Include <asm/pal.h> so we can get building again.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: David Rusling <david.rusling@linaro.org>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile
Pull tile architecture fixes from Chris Metcalf:
"This fixes the bug that Al Viro spotted with the compat llseek code.
I also fixed the compat syscall definitions to use the new syscall
define macros to properly sign-extend their arguments."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: properly use COMPAT_SYSCALL_DEFINEx
tile: work around bug in the generic sys_llseek
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag bugfixes from James Hogan:
"A couple of fairly minor arch/metag integration fixes from v3.9-rc1:
- remove SET_PERSONALITY(): use default definition like other arches
now do.
- inhibit NUMA balancing: like SH, NUMA is used for memories with
different latencies. ARCH_WANT_VARIABLE_LOCALITY has been added
for this purpose."
* tag 'metag-for-v3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Inhibit NUMA balancing.
metag: remove SET_PERSONALITY()
|
|
The orion5x-lacie-ethernet-disk-mini-v2.dts file was using
"marvell-orion5x-88f5182" as a compatible string, while it should have
been "marvell,orion5x-88f5182".
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
There is no need to have a #address-cells property in the MPIC Device
Tree node, and more than that, having it confuses the of_irq_map_raw()
logic, which will be used by the Marvell PCIe driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
During the system initialization, the orion_setup_cpu_mbus_target()
function reads the SDRAM address decoding registers to find out how
many chip-selects of SDRAM have been enabled, and builds a small array
with one entry per chip-select. This array is then used by device
drivers (XOR, Ethernet, etc.) to configure their own address decoding
windows to the SDRAM.
However, devices can only access the first 32 bits of the physical
memory. Even though LPAE is not supported for now, some Marvell boards
are now showing up with 8 GB of RAM, configured using two SDRAM
address decoding windows: the first covering the first 4 GB, the
second covering the last 4 GB. The array built by
orion_setup_cpu_mbus_target() has therefore two entries, and device
drivers try to set up two address decoding windows to the
SDRAM. However, in the device registers for the address decoding, the
base address is only 32 bits, so those two windows overlap each other,
and the devices do not work at all.
This patch makes sure that the array built by
orion_setup_cpu_mbus_target() only contains the SDRAM decoding windows
that correspond to the first 4 GB of the memory. To do that, it
ignores the SDRAM decoding windows for which the 4 low-order bits are
not zero (the 4 low-order bits of the base register are used to store
bits 32:35 of the base address, so they actually indicate whether the
base address is above 4 GB).
This patch allows the newly introduced armada-xp-gp board to properly
operate when it is mounted with more than 4 GB of RAM. Without that,
all devices doing DMA (for example XOR and Ethernet) do not work at
all.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Setting the reg-io-width to 1 byte represents more accurate
description of the HW.
This will fix an issue where UART driver causes kernel
panic during bootup. Gregory CLEMENT traced the issue to
autoconfig() in 8250.c, where the existence of FIFO is
checked from UART_IIR register. The register is now read as
32-bit value as the reg-io-width is set to 4-bytes. The
retuned value seems to contain bogus data for bits 31:8,
causing the issue.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The commit:
48be9ac ARM: Dove: split legacy and DT setup
removed the RTC initialization. This patch re-enables the RTC
via the DT.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
This patch modifies the Armada 370 Reference Design DTS file to enable
support for the two USB ports found on this board.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
Commit 5b03df9ace680d7cdd34a69dfd85ca5f74159d18 ("ARM: dove: switch to
DT clock providers") added "select COMMON_CLK_DOVE" to Marvell Dove's
Kconfig entry. But there's no Kconfig symbol COMMON_CLK_DOVE, which
makes this select statement a nop. It's probably a leftover of some
experimental code that never hit mainline. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
The Marvell RTC on Kirkwood makes use of the runit clock. Ensure the
driver clk_prepare_enable() this clock, otherwise there is a danger
the SoC will lockup when accessing RTC registers with the clock
disabled.
Reported-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
