| Age | Commit message (Collapse) | Author |
|---|
|
Impact: split out a function, no functional change
Xen needs to be able to access percpu data from very early on. For
various reasons, it cannot also load the gdt at that time. It does,
however, have a pefectly functional gdt at that point, so there's no
pressing need to reload the gdt.
Split the function to load the segment registers off, so Xen can call
it directly.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Impact: cleanup, prepare for xen boot fix.
Xen needs to call this function very early to setup the GDT and
per-cpu segments. Remove the call to smp_processor_id() and just
pass in the cpu number.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Impact: fix possible tlb mis-flushing on UV
uv_flush_send_and_wait() should return a pointer if the broadcast
remote tlb shootdown requests fail. That causes the conventional IPI
method of shootdown to be used.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: cleanup
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Reduce include file dependencies a bit - remove the two headers
that are included in irq_vectors.h.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Describe the layout of x86 trap/exception/IRQ vectors and clean
up indentation and other small details.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Remove a Voyager complication from the generic irq_vectors.h header.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
They dont belong into the generic headers.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Move the spurious vector sanity check to the place where it's
defined - out of a .c file.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Most of the vector layout on 32-bit and 64-bit is identical now,
so eliminate the duplicated enumeration of the vectors.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Add a slot for the performance monitoring interrupt. Not yet used
by any subsystem - but the hardware has it. (This eases integration
with performance monitoring code.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix potential miscompile (currently believed non-manifest)
As the comment explains, the VBE DDC call can clobber any register.
Tell the compiler about that fact.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: Fix build when CONFIG_PARAVIRT_DEBUG is enabled
Fix missed convertion to using callee-saved calls for pud_val, which
causes a compile error when CONFIG_PARAVIRT_DEBUG is enabled.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Impact: Optimization
In the native case, pte_val, make_pte, etc are all just identity
functions, so there's no need to clobber a lot of registers over them.
(This changes the 32-bit callee-save calling convention to return both
EAX and EDX so functions can return 64-bit values.)
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Optimization
Functions with the callee save calling convention clobber many fewer
registers than the normal C calling convention. Implement variants of
PVOP_V?CALL* accordingly. This only bothers with functions up to 3
args, since functions with more args may as well use the normal
calling convention.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Optimization
One of the problems with inserting a pile of C calls where previously
there were none is that the register pressure is greatly increased.
The C calling convention says that the caller must expect a certain
set of registers may be trashed by the callee, and that the callee can
use those registers without restriction. This includes the function
argument registers, and several others.
This patch seeks to alleviate this pressure by introducing wrapper
thunks that will do the register saving/restoring, so that the
callsite doesn't need to worry about it, but the callee function can
be conventional compiler-generated code. In many cases (particularly
performance-sensitive cases) the callee will be in assembler anyway,
and need not use the compiler's calling convention.
Standard calling convention is:
arguments return scratch
x86-32 eax edx ecx eax ?
x86-64 rdi rsi rdx rcx rax r8 r9 r10 r11
The thunk preserves all argument and scratch registers. The return
register is not preserved, and is available as a scratch register for
unwrapped callee code (and of course the return value).
Wrapped function pointers are themselves wrapped in a struct
paravirt_callee_save structure, in order to get some warning from the
compiler when functions with mismatched calling conventions are used.
The most common paravirt ops, both statically and dynamically, are
interrupt enable/disable/save/restore, so handle them first. This is
particularly easy since their calls are handled specially anyway.
XXX Deal with VMI. What's their calling convention?
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Optimization
Each asm paravirt-ops call says what registers are available for
clobbering. This patch makes use of this to selectively save/restore
registers around each pvops call. In many cases this significantly
shrinks code size.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Fix latent bug
The clobber is trying to say that anything except RDI is available for
clobbering, but actually clobbers everything. This hasn't mattered
because the clobbers were basically ignored, but subsequent patches
will rely on them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Optimization
Several paravirt ops implementations simply return their arguments,
the most obvious being the make_pte/pte_val class of operations on
native.
On 32-bit, the identity function is literally a no-op, as the calling
convention uses the same registers for the first argument and return.
On 64-bit, it can be implemented with a single "mov".
This patch adds special identity functions for 32 and 64 bit argument,
and machinery to recognize them and replace them with either nops or a
mov as appropriate.
At the moment, the only users for the identity functions are the
pagetable entry conversion functions.
The result is a measureable improvement on pagetable-heavy benchmarks
(2-3%, reducing the pvops overhead from 5 to 2%).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
Impact: Cleanup
Move remaining mmu-related stuff into mmu.c.
A general cleanup, and lay the groundwork for later patches.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
|
|
|
|
Impact: fix rare crash on 32-bit
The 32-bit APIC drivers had their send_IPI_self vectors set to NULL,
but ioapic_retrigger_irq() depends on it being always set. Fix it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In Linus' current -git the cpumask member is now a pointer.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This kernel symbol provides a way for drivers to switch on alternate
function for a certain GPIO pin. Turning it off is done implicitly when
changing the GPIO direction, as that would be fixed when using the given
pin als alternate function.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Remove the {set,get}_434_reg() prototypes, as the functions have been
removed. Also move the prototypes for {get,set}_latch_u5() to the correct
place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
As rb532_dev3_ctl_res is not used by any platform device, it can be dropped
when not used for holding the physical address of the device 3 controller.
Also a size of one byte should suffice when ioremapping the physical
address mentioned above, as only a single byte is being read from and
written to it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
These kernel symbols are unused. Also, since dev3 init has been moved to
devices.c, set_434_reg() breaks compiling as it uses dev3.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This code doesn't belong to gpio.c, as it's completely unrelated to
GPIO. As dev1 and dev2 init code is in devices.c, it seems to be a more
adequate place.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The data to be written is just a byte, so use writeb instead of writel.
Also, dev3.base contains the address, not the data so referencing here
is wrong.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This register just contains the address of the actual resource, so
initialisation has to be the same as cf_slot0_res and nand_slot0_res.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
As the korina ethernet driver uses platform_get_drvdata() to extract the
driver specific data from the platform device, driver_data has to be
used here.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Auto-detection works just fine, so use it instead of specifying the type
manually. Also define a platform device for the uart, as suggested by
David Daney.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
As the pata-rb532-cf driver calls gpio_direction_input(), the calls to
rb532_gpio_set_func() and rb532_gpio_direction_input() are not needed since
the alternate function is automatically being disabled when changing the
GPIO pin direction.
The later two calls to rb532_gpio_set_{ilevel,istat}() are implicitly being
done by the IRQ initialisation of pata-rb532-cf.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When a driver calls gpio_set_direction_{input,output}(), it obviously
doesn't want the alternate function for that pin to be active (as the
direction would not matter in that case). This patch ensures alternate
function is disabled when the direction is being changed.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources;
add defines to make this clear when addressing them later in code.
The mapped GPIOs support triggering on either level high or low. To
achieve this, the set_type() function calls rb532_gpio_set_ilevel() for
interrupts of the above mentioned group.
As there is no way to alter the triggering characteristics of the other
interrupts, accept level triggering on status high only. (This is just a
guess; but as the system boots fine and interrupt-driven devices (e.g.
serial console) work with no implications, it seems to be right.)
To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the
interrupt status bit of the corresponding GPIO pin). This is done inside
rb532_disable_irq().
After applying these changes I could undo most of my former "fixes" to
pata-rb532-cf. Particularly all interrupt handling can be done
generically via set_irq_type() as it was before.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The code is rather based on trial-and-error than knowledge. Verified Via
Rhine functionality in PIO as well as MMIO mode.
[Looks sane -- Ralf]
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The algorithm works unconditionally. If bitval is one, the first line is
a no op and the second line sets the bit at offset position. Vice versa,
if bitval is zero, the first line clears the bit at offset position and
the second line is a no op.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The previous definition inadvertently omits Octeon which currently is
treated as an architecture variant separate from MIPS32 and MIPS64.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If a context switch occurred between the watch exception and reading the
watch registers, it would be possible for the new process to corrupt their
state. Enabling interrupts only after the watch registers are read avoids
this race.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This fixes the ptrace ABI for watch registers, and should allow 64bit
kernels to use the watch register support.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add platform support to use rtc-tx4939 driver.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The special IP27 DMA code selected by DMA_IP27 has been removed a while
ago turning DMA_IP27 into almost a nop. Also fixup the broken logic of
its last users memcpy.S and memcpy-inatomic.s.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
And while at it, convert all functions from macros to inline functions
for sanity.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This shaves of 1912 bytes of an IP27 defconfig kernel and avoids
unexpected overflow behaviour in atomic_sub_if_positive. Apply the same
changes to the atomic64_* functions for consistency.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Original commit 1c0fe6e3bda0464728c23c8d84aa47567e8b716c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
