| Age | Commit message (Collapse) | Author |
|---|
|
commit ca499fc87ed945094d952da0eb7eea7dbeb1feec upstream.
The PCI host bridge scan handler installs its own notify handler,
handle_hotplug_event_root(), by itself. Nevertheless, the ACPI
hotplug framework also installs the common notify handler,
acpi_hotplug_notify_cb(), for PCI root bridges. This causes
acpi_hotplug_notify_cb() to call _OST method with unsupported
error as hotplug.enabled is not set.
To address this issue, introduce hotplug.ignore flag, which
indicates that the scan handler installs its own notify handler by
itself. The ACPI hotplug framework does not install the common
notify handler when this flag is set.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
[rjw: Changed the name of the new flag]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 176a88d79d6b5aebabaff16734e8b3107efcaaad upstream.
According to the ACPI spec (5.0, Section 6.3.5), the "Device
insertion in progress (pending)" (0x80) _OST status code is
reserved for the "Insertion Processing" (0x200) source event
which is "a result of an OSPM action". Specifically, it is not
a notification, so that status code should not be used during
notification processing, which unfortunately is done by
acpi_scan_bus_device_check().
For this reason, drop the ACPI_OST_SC_INSERT_IN_PROGRESS _OST
status evaluation from there (it was a mistake to put it in there
in the first place).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit caf5c03f (ACPI: Move acpi_bus_get_device() from bus.c to
scan.c) caused acpi_bus_get_device() to be exported using
EXPORT_SYMBOL_GPL(), but that broke some binary drivers in
existence, so revert that change.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
"APIC" should be "ACPI" here.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* acpi-hotplug:
PM / hibernate / memory hotplug: Rework mutual exclusion
PM / hibernate: Create memory bitmaps after freezing user space
ACPI / scan: Change ordering of locks for device hotplug
|
|
Change the ordering of device hotplug locks in scan.c so that
acpi_scan_lock is always acquired after device_hotplug_lock.
This will make it possible to use device_hotplug_lock around some
code paths that acquire acpi_scan_lock safely (most importantly
system suspend and hibernation). Apart from that, acpi_scan_lock
is platform-specific and device_hotplug_lock is general, so the
new ordering appears to be more appropriate from the overall
design viewpoint.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
|
* acpi-hotplug:
ACPI / hotplug: Remove containers synchronously
driver core / ACPI: Avoid device hot remove locking issues
|
|
The current protocol for handling hot remove of containers is very
fragile and causes acpi_eject_store() to acquire acpi_scan_lock
which may deadlock with the removal of the device that it is called
for (the reason is that device sysfs attributes cannot be removed
while their callbacks are being executed and ACPI device objects
are removed under acpi_scan_lock).
The problem is related to the fact that containers are handled by
acpi_bus_device_eject() in a special way, which is to emit an
offline uevent instead of just removing the container. Then, user
space is expected to handle that uevent and use the container's
"eject" attribute to actually remove it. That is fragile, because
user space may fail to complete the ejection (for example, by not
using the container's "eject" attribute at all) leaving the BIOS
kind of in a limbo. Moreover, if the eject event is not signaled
for a container itself, but for its parent device object (or
generally, for an ancestor above it in the ACPI namespace), the
container will be removed straight away without doing that whole
dance.
For this reason, modify acpi_bus_device_eject() to remove containers
synchronously like any other objects (user space will get its uevent
anyway in case it does some other things in response to it) and
remove the eject_pending ACPI device flag that is not used any more.
This way acpi_eject_store() doesn't have a reason to acquire
acpi_scan_lock any more and one possible deadlock scenario goes
away (plus the code is simplified a bit).
Reported-and-tested-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
|
* acpi-assorted:
ACPI / osl: Kill macro INVALID_TABLE().
earlycpio.c: Fix the confusing comment of find_cpio_data().
ACPI / x86: Print Hot-Pluggable Field in SRAT.
ACPI / thermal: Use THERMAL_TRIPS_NONE macro to replace number
ACPI / thermal: Remove unused macros in the driver/acpi/thermal.c
ACPI / thermal: Remove the unused lock of struct acpi_thermal
ACPI / osl: Fix osi_setup_entries[] __initdata attribute location
ACPI / numa: Fix __init attribute location in slit_valid()
ACPI / dock: Fix __init attribute location in find_dock_and_bay()
ACPI / Sleep: Fix incorrect placement of __initdata
ACPI / processor: Fix incorrect placement of __initdata
ACPI / EC: Fix incorrect placement of __initdata
ACPI / scan: Drop unnecessary label from acpi_create_platform_device()
ACPI: Move acpi_bus_get_device() from bus.c to scan.c
ACPI / scan: Allow platform device creation without any IO resources
ACPI: Cleanup sparse warning on acpi_os_initialize1()
platform / thinkpad: Remove deprecated hotkey_report_mode parameter
ACPI: Remove the old /proc/acpi/event interface
|
|
* acpi-pm:
ACPI / PM: Add state information to error message in acpi_device_set_power()
ACPI / PM: Remove redundant power manageable check from acpi_bus_set_power()
ACPI / PM: Use ACPI_STATE_D3_COLD instead of ACPI_STATE_D3 everywhere
ACPI / PM: Make messages in acpi_device_set_power() print device names
ACPI / PM: Only set power states of devices that are power manageable
|
|
* acpi-cleanup: (21 commits)
ACPI / dock: fix error return code in dock_add()
ACPI / dock: Drop unnecessary local variable from dock_add()
ACPI / dock / PCI: Drop ACPI dock notifier chain
ACPI / dock: Do not check CONFIG_ACPI_DOCK_MODULE
ACPI / dock: Do not leak memory on falilures to add a dock station
ACPI: Drop ACPI bus notifier call chain
ACPI / dock: Rework the handling of notifications
ACPI / dock: Simplify dock_init_hotplug() and dock_release_hotplug()
ACPI / dock: Walk list in reverse order during removal of devices
ACPI / dock: Rework and simplify find_dock_devices()
ACPI / dock: Drop the hp_lock mutex from struct dock_station
ACPI: simplify acpiphp driver with new helper functions
ACPI: simplify dock driver with new helper functions
ACPI: Export acpi_(bay)|(dock)_match() from scan.c
ACPI: introduce two helper functions for _EJ0 and _LCK
ACPI: introduce helper function acpi_execute_simple_method()
ACPI: introduce helper function acpi_has_method()
ACPI / dock: simplify dock_create_acpi_device()
ACPI / dock: mark initialization functions with __init
ACPI / dock: drop redundant spin lock in dock station object
...
|
|
|
|
Move acpi_bus_get_device() from bus.c to scan.c which allows
acpi_bus_data_handler() to become static and clean up the latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There are several places in the tree where ACPI_STATE_D3 is used
instead of ACPI_STATE_D3_COLD which should be used instead for
clarity. Modify them all to use ACPI_STATE_D3_COLD as appropriate.
[The definition of ACPI_STATE_D3 itself cannot go away at this point
as it is part of ACPICA.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
|
|
Functions acpi_dock_match() and acpi_bay_match() in scan.c can be
shared with dock.c to reduce code duplication, so export them as
global functions.
Also add a new function acpi_ata_match() to check whether an ACPI
device object represents an ATA device.
[rjw: Changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce two helper functions, acpi_evaluate_ej0() and
acpi_evaluate_lck(), that will execute the _EJ0 and _LCK ACPI
control methods, respectively, and use them to simplify the
ACPI scan code.
[rjw: Changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Introduce helper function acpi_has_method() and use it in a number
of places to simplify code.
[rjw: Changelog]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
An ACPI_NOTIFY_BUS_CHECK notification means that we should scan the
entire namespace starting from the given handle even if the device
represented by that handle is present (other devices below it may
just have appeared).
For this reason, modify acpi_scan_bus_device_check() to always run
acpi_bus_scan() if the notification being handled is of type
ACPI_NOTIFY_BUS_CHECK.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: 3.10+ <stable@vger.kernel.org>
|
|
In acpi_bus_device_attach(), if there is an ACPI device object
for the given handle and that device object has a scan handler
attached to it already, there's nothing more to do for that handle.
Moreover, if acpi_scan_attach_handler() is called then, it may
execute the .attach() callback of the ACPI scan handler already
attached to the device object and that may lead to interesting
breakage.
For this reason, make acpi_bus_device_attach() return success
immediately when the handle's device object has a scan handler
attached to it.
Reported-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: 3.10+ <stable@vger.kernel.org>
|
|
The acpi_device_list list is not used, so removed it.
[rjw: Changelog]
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* acpi-assorted:
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI: Remove unused flags in acpi_device_flags
ACPI: Remove useless initializers
ACPI / battery: Make sure all spaces are in correct places
ACPI: add _STA evaluation at do_acpi_find_child()
ACPI / EC: access user space with get_user()/put_user()
|
|
* acpi-scan:
ACPI / scan: Do not bind ACPI drivers to objects with scan handlers
ACPI / ia64 / sba_iommu: Use ACPI scan handler for device discovery
ACPI / scan: Simplify ACPI driver probing
|
|
* acpi-hotplug:
ACPI: Do not use CONFIG_ACPI_HOTPLUG_MEMORY_MODULE
ACPI / cpufreq: Add ACPI processor device IDs to acpi-cpufreq
Memory hotplug: Move alternative function definitions to header
ACPI / processor: Fix potential NULL pointer dereference in acpi_processor_add()
Memory hotplug / ACPI: Simplify memory removal
ACPI / scan: Add second pass of companion offlining to hot-remove code
Driver core / MM: Drop offline_memory_block()
ACPI / processor: Pass processor object handle to acpi_bind_one()
ACPI: Drop removal_type field from struct acpi_device
Driver core / memory: Simplify __memory_block_change_state()
ACPI / processor: Initialize per_cpu(processors, pr->id) properly
CPU: Fix sysfs cpu/online of offlined CPUs
Driver core: Introduce offline/online callbacks for memory blocks
ACPI / memhotplug: Bind removable memory blocks to ACPI device nodes
ACPI / processor: Use common hotplug infrastructure
ACPI / hotplug: Use device offline/online for graceful hot-removal
Driver core: Use generic offline/online for CPU offline/online
Driver core: Add offline/online device operations
|
|
On HP Folio 13-2000, the BIOS defines a CMOS RTC Operation Region and
the EC's _REG methord accesses that region. Thus an appropriate
address space handler must be registered for that region before the
EC driver is loaded.
Introduce a mechanism for adding CMOS RTC address space handlers.
Register an ACPI scan handler for CMOS RTC devices such that, when
a device of that kind is detected during an ACPI namespace scan, a
common CMOS RTC operation region address space handler will be
installed for it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=54621
Reported-and-tested-by: Stefan Nagy <public@stefan-nagy.at>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Commit 3b63aaa70e1 (PCI: acpiphp: Do not use ACPI PCI subdriver
mechanism) introduced an ACPI dock support regression, because it
changed the relative initialization order of the ACPI dock subsystem
and the ACPI-based PCI hotplug (acpiphp).
Namely, the ACPI dock subsystem has to be initialized before
acpiphp_enumerate_slots() is first run, which after commit
3b63aaa70e1 happens during the initial enumeration of the PCI
hierarchy triggered by the initial ACPI namespace scan in
acpi_scan_init(). For this reason, the dock subsystem has to be
initialized before the initial ACPI namespace scan in
acpi_scan_init().
To make that happen, modify the ACPI dock subsystem to be
non-modular and add the invocation of its initialization routine,
acpi_dock_init(), to acpi_scan_init() directly before the initial
namespace scan.
[rjw: Changelog, removal of dock_exit().]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59501
Reported-and-tested-by: Alexander E. Patrakov <patrakov@gmail.com>
Tested-by: Illya Klymov <xanf@xanf.me>
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI drivers must not be bound to device objects having scan handlers
attatched to them, so make acpi_device_probe() fail with -EINVAL if the
device object being probed has an ACPI scan handler.
After this change the analogous check introduced into the ACPI video
driver by commit 8c9b7a7 (ACPI / video: Do not bind to device objects
with a scan handler) is not necessary any more and may be dropped, so
drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Tony Luck <tony.luck@gmail.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
|
There is no particular reason why acpi_bus_driver_init() needs to be
a separate function and its location with respect to its only caller,
acpi_device_probe(), makes the code a bit difficult to follow.
Besides, it doesn't really make sense to check if 'device' is not
NULL in acpi_bus_driver_init(), because we've already dereferenced
dev->driver in acpi_device_probe() at that point and, moreover,
'device' cannot be NULL then, because acpi_device_probe() is called
via really_probe() (which also sets dev->driver for that matter).
For these reasons, drop acpi_bus_driver_init() altogether and move
the remaining code from it directly into acpi_device_probe().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
With the introduction of ACPI scan handlers, ACPI device objects
with an ACPI scan handler attached to them must not be bound to
by ACPI drivers any more. Unfortunately, however, the ACPI video
driver attempts to do just that if there is a _ROM ACPI control
method defined under a device object with an ACPI scan handler.
Prevent that from happening by making the video driver's "add"
routine check if the device object already has an ACPI scan handler
attached to it and return an error code in that case.
That is not sufficient, though, because acpi_bus_driver_init() would
then clear the device object's driver_data that may be set by its
scan handler, so for the fix to work acpi_bus_driver_init() has to be
modified to leave driver_data as is on errors.
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091
Bisected-and-tested-by: Dmitry S. Demin <dmitryy.demin@gmail.com>
Reported-and-tested-by: Jason Cassell <bluesloth600@gmail.com>
Tracked-down-by: Aaron Lu <aaron.lu@intel.com>
Cc: 3.9+ <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
|
|
Commit 9f29ab11ddbf ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600. Tony says:
"It panics with the message:
Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel
[...] my problem comes from arch/ia64/hp/common/sba_iommu.c
where the code in sba_init() says:
acpi_bus_register_driver(&acpi_sba_ioc_driver);
if (!ioc_list) {
but because of this change we never managed to call ioc_init()
so ioc_list doesn't get set up, and we die."
Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the introduction of ACPI scan handlers, an ACPI device object
with an ACPI scan handler attached to it must not be bound to an ACPI
driver any more. Therefore it doesn't make sense to match those
ACPI device objects against a newly registered ACPI driver in
acpi_bus_match(), so make that function return 0 if the device
object passed to it has an ACPI scan handler attached.
This also addresses a regression related to a broken ACPI table in
the BIOS, where it has defined a _ROM method under the PCI root
bridge object. This causes the video module to treat that object
as a display controller device (since only display devices are
supposed to have a _ROM method defined according to the ACPI spec).
As a result, the ACPI video driver binds to the PCI root bridge
object and overwrites the previously assigned driver_data field of
it, causing subsequent calls to acpi_get_pci_dev() to fail.
[rjw: Subject and changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58091
Reported-by: Jason Cassell <bluesloth600@gmail.com>
Reported-and-bisected-by: Dmitry S. Demin <dmitryy.demin@gmail.com>
Cc: 3.9+ <stable@kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
As indicated by comments in mm/memory_hotplug.c:remove_memory(),
if CONFIG_MEMCG is set, it may not be possible to offline all of the
memory blocks held by one module (FRU) in one pass (because one of
them may be used by the others to store page cgroup in that case
and that block has to be offlined before the other ones).
To handle that arguably corner case, add a second pass of companion
device offlining to acpi_scan_hot_remove() and make it ignore errors
returned in the first pass (and make it skip the second pass if the
first one is successful).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
|
The ACPI processor driver was the only user of the removal_type
field in struct acpi_device, but it doesn't use that field any more
after recent changes. Thus, removal_type has no more users, so drop
it along with the associated data type.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
|
|
Pull slave-dma fixes from Vinod Koul:
"We have two patches from Andy & Rafael fixing the Lynxpoint dma"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
ACPI / LPSS: register clock device for Lynxpoint DMA properly
dma: acpi-dma: parse CSRT to extract additional resources
|
|
Following commit 6b772e8f9 (ACPI: Update PNPID match handling for
notify), the acpi_scan_init_hotplug() calls acpi_set_pnp_ids() which
allocates acpi_hardware_id and copies a few strings (kstrdup). If the
devices does not have hardware_id set, the function exits without
freeing the previously allocated ids (and kmemleak complains). This
patch calls simply changes 'return' on error to a 'goto out' which
calls acpi_free_pnp_ids().
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since we have CSRT only to get additional DMA controller resources, let's get
rid of drivers/acpi/csrt.c and move its logic inside ACPI DMA helpers code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Split the ACPI processor driver into two parts, one that is
non-modular, resides in the ACPI core and handles the enumeration
and hotplug of processors and one that implements the rest of the
existing processor driver functionality.
The non-modular part uses an ACPI scan handler object to enumerate
processors on the basis of information provided by the ACPI namespace
and to hook up with the common ACPI hotplug infrastructure. It also
populates the ACPI handle of each processor device having a
corresponding object in the ACPI namespace, which allows the driver
proper to bind to those devices, and makes the driver bind to them
if it is readily available (i.e. loaded) when the scan handler's
.attach() routine is running.
There are a few reasons to make this change.
First, switching the ACPI processor driver to using the common ACPI
hotplug infrastructure reduces code duplication and size considerably,
even though a new file is created along with a header comment etc.
Second, since the common hotplug code attempts to offline devices
before starting the (non-reversible) removal procedure, it will abort
(and possibly roll back) hot-remove operations involving processors
if cpu_down() returns an error code for one of them instead of
continuing them blindly (if /sys/firmware/acpi/hotplug/force_remove
is unset). That is a more desirable behavior than what the current
code does.
Finally, the separation of the scan/hotplug part from the driver
proper makes it possible to simplify the driver's .remove() routine,
because it doesn't need to worry about the possible cleanup related
to processor removal any more (the scan/hotplug part is responsible
for that now) and can handle device removal and driver removal
symmetricaly (i.e. as appropriate).
Some user-visible changes in sysfs are made (for example, the
'sysdev' link from the ACPI device node to the processor device's
directory is gone and a 'physical_node' link is present instead
and a corresponding 'firmware_node' is present in the processor
device's directory, the processor driver is now visible under
/sys/bus/cpu/drivers/ and bound to the processor device), but
that shouldn't affect the functionality that users care about
(frequency scaling, C-states and thermal management).
Tested on my venerable Toshiba Portege R500.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
|
|
Modify the generic ACPI hotplug code to be able to check if devices
scheduled for hot-removal may be gracefully removed from the system
using the device offline/online mechanism introduced previously.
Namely, make acpi_scan_hot_remove() handling device hot-removal call
device_offline() for all physical companions of the ACPI device nodes
involved in the operation and check the results. If any of the
device_offline() calls fails, the function will not progress to the
removal phase (which cannot be aborted), unless its (new) force
argument is set (in case of a failing offline it will put the devices
offlined by it back online).
In support of 'forced' device hot-removal, add a new sysfs attribute
'force_remove' that will reside under /sys/firmware/acpi/hotplug/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael J Wysocki:
- ARM big.LITTLE cpufreq driver from Viresh Kumar.
- exynos5440 cpufreq driver from Amit Daniel Kachhap.
- cpufreq core cleanup and code consolidation from Viresh Kumar and
Stratos Karafotis.
- cpufreq scalability improvement from Nathan Zimmer.
- AMD "frequency sensitivity feedback" powersave bias for the ondemand
cpufreq governor from Jacob Shin.
- cpuidle code consolidation and cleanups from Daniel Lezcano.
- ARM OMAP cpuidle fixes from Santosh Shilimkar and Daniel Lezcano.
- ACPICA fixes and other improvements from Bob Moore, Jung-uk Kim, Lv
Zheng, Yinghai Lu, Tang Chen, Colin Ian King, and Linn Crosetto.
- ACPI core updates related to hotplug from Toshi Kani, Paul Bolle,
Yasuaki Ishimatsu, and Rafael J Wysocki.
- Intel Lynxpoint LPSS (Low-Power Subsystem) support improvements from
Rafael J Wysocki and Andy Shevchenko.
* tag 'pm+acpi-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (192 commits)
cpufreq: Revert incorrect commit 5800043
cpufreq: MAINTAINERS: Add co-maintainer
cpuidle: add maintainer entry
ACPI / thermal: do not always return THERMAL_TREND_RAISING for active trip points
ARM: s3c64xx: cpuidle: use init/exit common routine
cpufreq: pxa2xx: initialize variables
ACPI: video: correct acpi_video_bus_add error processing
SH: cpuidle: use init/exit common routine
ARM: S5pv210: compiling issue, ARM_S5PV210_CPUFREQ needs CONFIG_CPU_FREQ_TABLE=y
ACPI: Fix wrong parameter passed to memblock_reserve
cpuidle: fix comment format
pnp: use %*phC to dump small buffers
isapnp: remove debug leftovers
ARM: imx: cpuidle: use init/exit common routine
ARM: davinci: cpuidle: use init/exit common routine
ARM: kirkwood: cpuidle: use init/exit common routine
ARM: calxeda: cpuidle: use init/exit common routine
ARM: tegra: cpuidle: use init/exit common routine for tegra3
ARM: tegra: cpuidle: use init/exit common routine for tegra2
ARM: OMAP4: cpuidle: use init/exit common routine
...
|
|
* acpi-lpss:
ACPI / LPSS: make code less confusing for reader
ACPI / LPSS: Add support for exposing LTR registers to user space
ACPI / scan: Add special handler for Intel Lynxpoint LPSS devices
|
|
Currently the pci_slot driver doesn't update PCI slot devices when PCI
device hotplug event happens, which may cause memory leak and returning
stale information to user.
Now the pci_slot driver has been changed as built-in driver, so invoke
PCI slot enumeration and destroy routines directly from the PCI core.
And remove ACPI PCI sub-driver related code because it isn't needed
any more.
[bhelgas: removed "extern" from function declarations]
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Toshi Kani <toshi.kani@hp.com>
|
|
ACPI spec states that the OS evaluates _STA after calling _EJ0
in order to verify if eject was successful. Added a check to
verify if the enabled bit of the status value is cleared after
_EJ0.
Note, the present bit is not checked since some FW implementations
do not clear the present bit until the hardware is physically
removed.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When the kernel calls _OSC with OSC_SB_HOTPLUG_OST_SUPPORT bit
set at boot-time, the OS is responsible for calling _OST for
ACPI hotplug events. However, when hotplug.enabled attribute
is unset for ACPI scan drivers, their notify handlers are removed
and _OST is not called for ACPI hotplug events as a result.
This patch keeps the notify handler of ACPI scan drivers,
acpi_hotplug_notify_cb(), installed regardless of the state of
hotplug.enabled. The notify handler then checks if hotplug.enabled
is set for the associated scan handler. If unset, the notify
handler calls _OST with a proper error code. The patch also
eliminates ACPI namespace walk when hotplug.enabled is changed
via sysfs.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When installing/removing a notify handler to/from an ACPI device
object, ACPI core tries to match its associated scan handler to
see if it supports hotplug. However, the matching logic of the
notify handler is different from the matching logic of attaching
a scan handler to an ACPI device object. This patch updates the
matching logic of the notify handlers to be consistent with the
attach handling.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch introduces acpi_set_pnp_ids() and acpi_free_pnp_ids(),
which are updated from acpi_device_set_id() and acpi_free_ids(),
to setup and free acpi_device_pnp for a given acpi_handle. They
can be called without acpi_device.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch updates the internal operations of acpi_device_set_id()
to setup acpi_device_pnp without using acpi_device. There is no
functional change to acpi_device_set_id() in this patch.
acpi_pnp_type is added to acpi_device_pnp, so that PNPID type is
self-contained within acpi_device_pnp. acpi_add_id(), acpi_bay_match(),
acpi_dock_match(), acpi_ibm_smbus_match() and acpi_is_video_device()
are changed to take acpi_handle as an argument, instead of acpi_device.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Devices on the Intel Lynxpoint Low Power Subsystem (LPSS) have some
common features that aren't shared with any other platform devices,
including the clock and LTR (Latency Tolerance Reporting) registers.
It is better to handle those features in common code than to bother
device drivers with doing that (I/O functionality-wise the LPSS
devices are generally compatible with other devices that don't
have those special registers and may be handled by the same drivers).
The clock registers of the LPSS devices are now taken care of by
the special clk-x86-lpss driver, but the MMIO mappings used for
accessing those registers can also be used for accessing the LTR
registers on those devices (LTR support for the Lynxpoint LPSS is
going to be added by a subsequent patch). Thus it is convenient
to add a special ACPI scan handler for the Lynxpoint LPSS devices
that will create the MMIO mappings for accessing the clock (and
LTR in the future) registers and will register the LPSS devices'
clocks, so the clk-x86-lpss driver will only need to take care of
the main Lynxpoint LPSS clock.
Introduce a special ACPI scan handler for Intel Lynxpoint LPSS
devices as described above. This also reduces overhead related to
browsing the ACPI namespace in search of the LPSS devices before the
registration of their clocks, removes some LPSS-specific (and
somewhat ugly) code from acpi_platform.c and shrinks the overall code
size slightly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
|
|
Make the ACPI memory hotplug driver use struct acpi_scan_handler
for representing the object used to set up ACPI memory hotplug
functionality and to remove hotplug memory ranges and data
structures used by the driver before unregistering ACPI device
nodes representing memory. Register the new struct acpi_scan_handler
object with the help of acpi_scan_add_handler_with_hotplug() to allow
user space to manipulate the attributes of the memory hotplug
profile.
This results in a significant reduction of the drvier's code size
and removes some ACPI hotplug code duplication.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
|
|
Introduce user space interface for manipulating hotplug profiles
associated with ACPI scan handlers.
The interface consists of sysfs directories under
/sys/firmware/acpi/hotplug/, one for each hotplug profile, containing
an attribute allowing user space to manipulate the enabled field of
the corresponding profile. Namely, switching the enabled attribute
from '0' to '1' will cause the common hotplug notify handler to be
installed for all ACPI namespace objects representing devices matching
the scan handler associated with the given hotplug profile (and
analogously for the converse switch).
Drivers willing to use the new user space interface should add their
ACPI scan handlers with the help of new funtion
acpi_scan_add_handler_with_hotplug().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
|
|
Introduce new helper routine acpi_scan_handler_matching() for
checking if the given ACPI scan handler matches a given device ID
and rework acpi_scan_match_handler() to use the new routine (that
routine will also be useful for other purposes in the future).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
|
