| Age | Commit message (Collapse) | Author |
|---|
|
If the TPM has already been sent a SaveState command before the driver
is loaded it may have problems sending that same command again later.
This issue is seen with the Chromebook Pixel due to a firmware bug in
the legacy mode boot path which is sending the SaveState command
before booting the kernel. More information is available at
http://crbug.com/203524
This change introduces a retry of the SaveState command in the suspend
path in order to work around this issue. A future firmware update
should fix this but this is also a trivial workaround in the driver
that has no effect on systems that do not show this problem.
When this does happen the TPM responds with a non-fatal TPM_RETRY code
that is defined in the specification:
The TPM is too busy to respond to the command immediately, but the
command could be resubmitted at a later time. The TPM MAY return
TPM_RETRY for any command at any time.
It can take several seconds before the TPM will respond again. I
measured a typical time between 3 and 4 seconds and the timeout is set
at a safe 5 seconds.
It is also possible to reproduce this with commands via /dev/tpm0.
The bug linked above has a python script attached which can be used to
test for this problem. I tested a variety of TPMs from Infineon,
Nuvoton, Atmel, and STMicro but was only able to reproduce this with
LPC and I2C TPMs from Infineon.
The TPM specification only loosely defines this behavior:
TPM Main Level 2 Part 3 v1.2 r116, section 3.3. TPM_SaveState:
The TPM MAY declare all preserved values invalid in response to any
command other than TPM_Init.
TCG PC Client BIOS Spec 1.21 section 8.3.1.
After issuing a TPM_SaveState command, the OS SHOULD NOT issue TPM
commands before transitioning to S3 without issuing another
TPM_SaveState command.
TCG PC Client TIS 1.21, section 4. Power Management:
The TPM_SaveState command allows a Static OS to indicate to the TPM
that the platform may enter a low power state where the TPM will be
required to enter into the D3 power state. The use of the term "may"
is significant in that there is no requirement for the platform to
actually enter the low power state after sending the TPM_SaveState
command. The software may, in fact, send subsequent commands after
sending the TPM_SaveState command.
Change-Id: I52b41e826412688e5b6c8ddd3bb16409939704e9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
Support cancellation of TPM commands when driver is used in interrupt
mode.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
On one of my machines the cancellation of TPM commands does not work.
The reason is that by writing into sysfs 'cancel' the tpm_tis_ready
call causes the status flag TPM_STS_VALID to be set in the statusregister.
However, the TIS driver seems to wait for TPM_STS_COMMAND_READY.
Once a 2nd time sysfs 'cancel' is written to, the TPM_STS_COMMAND_READY flag
also gets set, resulting in TPM_STS_VALID|TPM_STS_COMMAND_READY to be
read from the status register.
This patch now converts req_canceled into a function to enable more complex
comparisons against possible cancellation status codes.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
We've been testing an alternative TPM for our embedded products and
found random kernel boot failures due to time outs after the continue
self test command.
This was happening randomly, and has been *very* hard to track down, but
it
looks like with this chip there is some kind of race with the
tpm_tis_status()
check of TPM_STS_COMMAND_READY. If things get there 'too fast' then
it sees the chip is ready, or tpm_tis_ready() works. Otherwise it takes
somewhere over 400ms before the chip will return TPM_STS_COMMAND_READY.
Adding some delay after tpm_continue_selftest() makes things reliably
hit the failure path, otherwise it is a crapshot.
The spec says it should be returning TPM_WARN_DOING_SELFTEST, not
holding
off on ready..
Boot log during this event looks like this:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0x3204, rev-id 64)
tpm_tis 70030000.tpm_tis: Issuing TPM_STARTUP
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
tpm_tis 70030000.tpm_tis: tpm_transmit: tpm_send: error -62
tpm_tis 70030000.tpm_tis: [Hardware Error]: TPM command timed out during
continue self test
The other TPM vendor we use doesn't show this wonky behaviour:
tpm_tis 70030000.tpm_tis: 1.2 TPM (device-id 0xFE, rev-id 70)
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
The TPM will respond to TPM_GET_CAP with TPM_ERR_INVALID_POSTINIT if
TPM_STARTUP has not been issued. Detect this and automatically
issue TPM_STARTUP.
This is for embedded applications where the kernel is the first thing
to touch the TPM.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
This patch changes the semantics of the duration calculation for an
ordinal, by masking out the higher bits of a tpm command, which specify
whether it's an TPM_PROTECTED_COMMAND, TPM_UNPROTECTED_COMMAND,
TPM_CONNECTION_COMMAND, TPM_CONNECTION_COMMAND, TPM_VENDOR_COMMAND.
(See TPM Main Spec Part 2 Section 17 for details).
For all TPM_PROTECTED and TPM_CONNECTION commands the results are
unchanged.
The TPM_UNPROTECTED commands are TSS commands and thus irrelevant as
they are not sent to the tpm.
For vendor commands the semantics change for ordinals 10 and 11 but
they were probably wrong anyway.
For everything else which has the ordinal set to 10 or 11 the semantics
change as it now uses TPM_UNDEFINED instead of TPM_SHORT which was
probably wrong anyway (but irrelevant as not defined by the standard).
This patch also gets rid of the (false positive) smatch warning:
drivers/char/tpm/tpm.c:360 tpm_calc_ordinal_duration() error: buffer
overflow 'tpm_protected_ordinal_duration' 12 <= 243
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
The entries in tpm_protected_ordinal_duration are exactly the same as
the first 12 in tpm_ordinal_duration, so we can simply remove this one,
and save some bytes.
This does not change the behavior of the driver.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
for-linus
|
|
tpm_write calls tpm_transmit without checking the return value and
assigns the return value unconditionally to chip->pending_data, even if
it's an error value.
This causes three bugs.
So if we write to /dev/tpm0 with a tpm_param_size bigger than
TPM_BUFSIZE=0x1000 (e.g. 0x100a)
and a bufsize also bigger than TPM_BUFSIZE (e.g. 0x100a)
tpm_transmit returns -E2BIG which is assigned to chip->pending_data as
-7, but tpm_write returns that TPM_BUFSIZE bytes have been successfully
been written to the TPM, altough this is not true (bug #1).
As we did write more than than TPM_BUFSIZE bytes but tpm_write reports
that only TPM_BUFSIZE bytes have been written the vfs tries to write
the remaining bytes (in this case 10 bytes) to the tpm device driver via
tpm_write which then blocks at
/* cannot perform a write until the read has cleared
either via tpm_read or a user_read_timer timeout */
while (atomic_read(&chip->data_pending) != 0)
msleep(TPM_TIMEOUT);
for 60 seconds, since data_pending is -7 and nobody is able to
read it (since tpm_read luckily checks if data_pending is greater than
0) (#bug 2).
After that the remaining bytes are written to the TPM which are
interpreted by the tpm as a normal command. (bug #3)
So if the last bytes of the command stream happen to be a e.g.
tpm_force_clear this gets accidentally sent to the TPM.
This patch fixes all three bugs, by propagating the error code of
tpm_write and returning -E2BIG if the input buffer is too big,
since the response from the tpm for a truncated value is bogus anyway.
Moreover it returns -EBUSY to userspace if there is a response ready to be
read.
Signed-off-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
This patch try to fix the S3 regression https://lkml.org/lkml/2012/10/5/433,
which includes below line:
[ 1554.684638] sysfs: cannot create duplicate filename '/devices/pnp0/00:0c/ppi'
The root cause is that ppi sysfs teardown code is MIA, so while S3 resume,
the ppi kobject will be created again upon existing one.
To make the tear down code simple, change the ppi subfolder creation from
using kobject_create_and_add to just using a named ppi attribute_group. Then
ppi sysfs teardown could be done with a simple sysfs_remove_group call.
Adjusted the name & return type for ppi sysfs init function.
Reported-by: Ben Guthro <ben@guthro.net>
Signed-off-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Highlights:
- Integrity: add local fs integrity verification to detect offline
attacks
- Integrity: add digital signature verification
- Simple stacking of Yama with other LSMs (per LSS discussions)
- IBM vTPM support on ppc64
- Add new driver for Infineon I2C TIS TPM
- Smack: add rule revocation for subject labels"
Fixed conflicts with the user namespace support in kernel/auditsc.c and
security/integrity/ima/ima_policy.c.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (39 commits)
Documentation: Update git repository URL for Smack userland tools
ima: change flags container data type
Smack: setprocattr memory leak fix
Smack: implement revoking all rules for a subject label
Smack: remove task_wait() hook.
ima: audit log hashes
ima: generic IMA action flag handling
ima: rename ima_must_appraise_or_measure
audit: export audit_log_task_info
tpm: fix tpm_acpi sparse warning on different address spaces
samples/seccomp: fix 31 bit build on s390
ima: digital signature verification support
ima: add support for different security.ima data types
ima: add ima_inode_setxattr/removexattr function and calls
ima: add inode_post_setattr call
ima: replace iint spinblock with rwlock/read_lock
ima: allocating iint improvements
ima: add appraise action keywords and default rules
ima: integrity appraisal extension
vfs: move ima_file_free before releasing the file
...
|
|
This patch declares the internal struct and functions as static to provide
more security.
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Kent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
The Physical Presence Interface enables the OS and the BIOS to cooperate and
provides a simple and straightforward platform user experience for
administering the TPM without sacrificing security.
V2: separate the patch out in a separate source file,
add #ifdef CONFIG_ACPI so it compiles out on ppc,
use standard error instead of ACPI error as return code of show/store fns.
V3: move #ifdef CONFIG_ACPI from .c file to .h file.
V4: move tpm_ppi code from tpm module to tpm_bios module.
V5: modify sys_add_ppi() so that ppi_attr_grp doesn't need to be exported
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
Moved the atomic_set of the data_pending variable until after the
tpm_read has completed processing. The existing code had a window of
time where a second write to the driver could clobber the tpm command
buffer.
Also fixed an issue where if close was called on the tpm device before a
read completed, the tpm command buffer would be returned to the OS,
which could contain sensitive information.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
Move the tpm_get_random api from the trusted keys code into the TPM
device driver itself so that other callers can make use of it. Also,
change the api slightly so that the number of bytes read is returned in
the call, since the TPM command can potentially return fewer bytes than
requested.
Acked-by: David Safford <safford@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
Break ACPI-specific pieces of the event log handling into their own file
and create tpm_eventlog.[ch] to store common event log handling code.
This will be required to integrate future event log sources on platforms
without ACPI tables.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
|
|
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull security subsystem updates from James Morris:
"Nothing groundbreaking for this kernel, just cleanups and fixes, and a
couple of Smack enhancements."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (21 commits)
Smack: Maintainer Record
Smack: don't show empty rules when /smack/load or /smack/load2 is read
Smack: user access check bounds
Smack: onlycap limits on CAP_MAC_ADMIN
Smack: fix smack_new_inode bogosities
ima: audit is compiled only when enabled
ima: ima_initialized is set only if successful
ima: add policy for pseudo fs
ima: remove unused cleanup functions
ima: free securityfs violations file
ima: use full pathnames in measurement list
security: Fix nommu build.
samples: seccomp: add .gitignore for untracked executables
tpm: check the chip reference before using it
TPM: fix memleak when register hardware fails
TPM: chip disabled state erronously being reported as error
MAINTAINERS: TPM maintainers' contacts update
Merge branches 'next-queue' and 'next' into next
Remove unused code from MPI library
Revert "crypto: GnuPG based MPI lib - additional sources (part 4)"
...
|
|
The tpm_pm_suspend()'s second argument of type pm_message_t is not
used, so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
If a driver calls tpm_dev_vendor_release for a device already released
then the driver will oops.
Signed-off-by: Andi Shyti <andi.shyti@gmail.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Adding proper kfree() before returning.
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
tpm_do_selftest() attempts to read a PCR in order to
decide if one can rely on the TPM being used or not.
The function that's used by __tpm_pcr_read() does not
expect the TPM to be disabled or deactivated, and if so,
reports an error.
It's fine if the TPM returns this error when trying to
use it for the first time after a power cycle, but it's
definitely not if it already returned success for a
previous attempt to read one of its PCRs.
The tpm_do_selftest() was modified so that the driver only
reports this return code as an error when it really is.
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Commit 3321c07ae5068568cd61ac9f4ba749006a7185c9 correctly clears the TPM
buffer if the user specified read length is >= the TPM buffer length. However,
if the user specified read length is < the TPM buffer length, then part of the
TPM buffer is left uncleared.
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: tpmdd-devel@lists.sourceforge.net
Cc: stable@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
This patch fixes an (ACPI S3) suspend regression introduced in commit
68d6e6713fcb ("tpm: Introduce function to poll for result of self test")
and occurring with an Infineon TPM and tpm_tis and tpm_infineon drivers
active.
The suspend problem occurred if the TPM was disabled and/or deactivated
and therefore the TPM_PCRRead checking the result of the (asynchronous)
self test returned an error code which then caused the tpm_tis driver to
become inactive and this then seemed to have negatively influenced the
suspend support by the tpm_infineon driver... Besides that the tpm_tis
drive may stay active even if the TPM is disabled and/or deactivated.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
It's incorrect to assume that buffers returned by the TPM
10 bytes long are always error reports. This patches
parses the error field in its header instead. The error report
is now being printed using dev_err() instead of dev_dbg(), making
it easier for users to provide more detailed bug reports.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Moved wait_for_stat to tpm.c so that other drivers can use it.
Also renamed it to avoid future namespace conflicts.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
This patch introduces a function that runs the TPM_ContinueSelfTest()
function and then polls the TPM to check whether it finished the selftest
and can receive new commands.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
|
|
Cleanup the tpm_continue_selftest function.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
|
|
Have the tpm_get_timeouts function return an error code.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
|
|
* 'next' of git://selinuxproject.org/~jmorris/linux-security: (95 commits)
TOMOYO: Fix incomplete read after seek.
Smack: allow to access /smack/access as normal user
TOMOYO: Fix unused kernel config option.
Smack: fix: invalid length set for the result of /smack/access
Smack: compilation fix
Smack: fix for /smack/access output, use string instead of byte
Smack: domain transition protections (v3)
Smack: Provide information for UDS getsockopt(SO_PEERCRED)
Smack: Clean up comments
Smack: Repair processing of fcntl
Smack: Rule list lookup performance
Smack: check permissions from user space (v2)
TOMOYO: Fix quota and garbage collector.
TOMOYO: Remove redundant tasklist_lock.
TOMOYO: Fix domain transition failure warning.
TOMOYO: Remove tomoyo_policy_memory_lock spinlock.
TOMOYO: Simplify garbage collector.
TOMOYO: Fix make namespacecheck warnings.
target: check hex2bin result
encrypted-keys: check hex2bin result
...
|
|
Since the buffer might contain security related data it might be a good idea to
zero the buffer after we have copied it to userspace.
This got assigned CVE-2011-1162.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
This patch changes the call of tpm_transmit by supplying the size of the
userspace buffer instead of TPM_BUFSIZE.
This got assigned CVE-2011-1161.
[The first hunk didn't make sense given one could expect
way less data than TPM_BUFSIZE, so added tpm_transmit boundary
check over bufsiz instead
The last parameter of tpm_transmit() reflects the amount
of data expected from the device, and not the buffer size
being supplied to it. It isn't ideal to parse it directly,
so we just set it to the maximum the input buffer can handle
and let the userspace API to do such job.]
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Suppress the output in the 'durations' sysfs entry if they were not read
during driver initialization. This is similar to other sysfs entries
that return nothing if for some reason sending the commands to the TPM
fails.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
This patch fixes a typo.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
This patch fixes the TPM's pubek sysfs entry that is accessible as long
as the TPM doesn't have an owner. It was necessary to shift the access to the
data by -10 -- the first byte immediately follows the 10 byte header. The
line
data = tpm_cmd.params.readpubek_out_buffer;
sets it at the offset '10' in the packet, so we can read the data array
starting at offset '0'.
Before:
Algorithm: 00 0C 00 00
Encscheme: 08 00
Sigscheme: 00 00
Parameters: 00 00 00 00 01 00 AC E2 5E 3C A0 78
Modulus length: -563306801
Modulus:
28 21 08 0F 82 CD F2 B1 E7 49 F7 74 70 BE 59 8C
43 78 B1 24 EA 52 E2 FE 52 5C 3A 12 3B DC 61 71
[...]
After:
Algorithm: 00 00 00 01
Encscheme: 00 03
Sigscheme: 00 01
Parameters: 00 00 08 00 00 00 00 02 00 00 00 00
Modulus length: 256
Modulus:
AC E2 5E 3C A0 78 DE 6C 9E CF 28 21 08 0F 82 CD
F2 B1 E7 49 F7 74 70 BE 59 8C 43 78 B1 24 EA 52
[...]
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Display the TPM's interface timeouts in a 'timeouts' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Adjust the interface timeouts if they are found to be too small, i.e., if
they are returned in milliseconds rather than microseconds as we heared
from Infineon that some (old) Infineon TPMs do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
The TPM driver currently discards the interface timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 4 interface timeout indicators of type u32.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Display the TPM's command timeouts in a 'durations' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Adjust the durations if they are found to be too small, i.e., if they are
returned in milliseconds rather than microseconds as some Infineon TPMs are
reported to do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
The TPM driver currently discards the durations values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
v4:
- sysfs entry 'durations' is now a patch of its own
- the work-around for TPMs reporting durations in milliseconds is now in a
patch of its own
v3:
- sysfs entry now called 'durations' to resemble TPM-speak (previously
was called 'timeouts')
v2:
- adjusting all timeouts for TPM devices reporting timeouts in msec rather
than usec
- also displaying in sysfs whether the timeouts are 'original' or 'adjusted'
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit c4ff4b829ef9e6353c0b133b7adb564a68054979.
Ted Ts'o reports:
"TPM is working for me so I can log into employer's network in 2.6.37.
It broke when I tried 2.6.38-rc6, with the following relevant lines
from my dmesg:
[ 11.081627] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
[ 25.734114] tpm_tis 00:0b: Operation Timed out
[ 78.040949] tpm_tis 00:0b: Operation Timed out
This caused me to get suspicious, especially since the _other_ TPM
commit in 2.6.38 had already been reverted, so I tried reverting
commit c4ff4b829e: "TPM: Long default timeout fix". With this commit
reverted, my TPM on my Lenovo T410 is once again working."
Requested-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 9b29050f8f75916f974a2d231ae5d3cd59792296.
It has caused hibernate regressions, for example Juri Sladby's report:
"I'm unable to hibernate 2.6.37.1 unless I rmmod tpm_tis:
[10974.074587] Suspending console(s) (use no_console_suspend to debug)
[10974.103073] tpm_tis 00:0c: Operation Timed out
[10974.103089] legacy_suspend(): pnp_bus_suspend+0x0/0xa0 returns -62
[10974.103095] PM: Device 00:0c failed to freeze: error -62"
and Rafael points out that some of the new conditionals in that commit
seem to make no sense. This commit needs more work and testing, let's
revert it for now.
Reported-by: Norbert Preining <preining@logic.at>
Reported-and-requested-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The current TPM TIS driver in git discards the timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
I am also adding a sysfs entry 'timeouts' showing the timeouts that are
being used.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.
This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Conflicts:
security/smack/smack_lsm.c
Verified and added fix by Stephen Rothwell <sfr@canb.auug.org.au>
Ok'd by Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
flush_scheduled_work() is deprecated and scheduled to be removed.
Directly flush chip->work instead.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
|
|
Add internal kernel tpm_send() command used to seal/unseal keys.
Changelog:
- replaced module_put in tpm_send() with new tpm_chip_put() wrapper
(suggested by David Howells)
- Make tpm_send() cmd argument a 'void *' (suggested by David Howells)
Signed-off-by: David Safford <safford@watson.ibm.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
