| Age | Commit message (Collapse) | Author |
|---|
|
as requested by Rob
Suggested-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The driver supports old up SiRFprimaII SoCs, this patch makes it support
the new SiRFmarco as well.
SiRFmarco, as a SMP SoC, adds new DMA_INT_EN_CLR and DMA_CH_LOOP_CTRL_CLR
registers, to disable IRQ/Channel, we should write 1 to the corresponding
bit in the two CLEAR register.
Tested on SiRFmarco using SPI driver:
$ /mnt/spidev-sirftest -D /dev/spidev32766.0
spi mode: 0
bits per word: 8
max speed: 500000 Hz (500 KHz)
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00
$ cat /proc/interrupts
CPU0 CPU1
32: 1593 0 GIC sirfsoc_timer0
33: 0 3533 GIC sirfsoc_timer1
44: 0 0 GIC sirfsoc_dma
45: 16 0 GIC sirfsoc_dma
47: 6 0 GIC sirfsoc_spi
50: 5654 0 GIC sirfsoc-uart
...
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
This driver could be used on different platforms. Thus, the HAVE_CLK dependency
is dropped away.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Vinod Koul <vinod.koul@intel.com>
CC: Dan Williams <djbw@fb.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
The dw_dmac driver was originally developed for avr32 to be used with the
Synopsys DesignWare AHB DMA controller. Starting from 2.6.38, access to
the device's i/o memory was done with the little-endian readl/writel
functions(1)
This broke the driver for the avr32 platform, because it needs big
(native) endian accessors. This patch makes the endianness configurable
using 'DW_DMAC_BIG_ENDIAN_IO', which will default be true for AVR32
I submitted this patch before(2) but then waited for Andy to finish other
changes to the same module(3).
(1) https://patchwork.kernel.org/patch/608211
(2) https://lkml.org/lkml/2012/8/26/148
(3) https://lkml.org/lkml/2012/9/21/173
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Havard Skinnemoen <havard@skinnemoen.net>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
1. virtual channel vs. physical channel
Virtual channel is managed by dmaengine
Physical channel handling resource, such as irq
Physical channel is alloced dynamically as descending priority,
freed immediately when irq done.
The availble highest priority physically channel will alwayes be alloced
Issue pending list -> alloc highest dma physically channel available -> dma done -> free physically channel
2. list: running list & pending list
submit: desc list -> pending list
issue_pending_list: if (IDLE) pending list -> running list; free pending list (RUN)
irq: free running list (IDLE)
check pendlist -> pending list -> running list; free pending list (RUN)
3. irq:
Each list generate one irq, calling callback
One list may contain several desc chain, in such case, make sure only the last desc list generate irq.
4. async
Submit will add desc chain to pending list, which can be multi-called
If multi desc chain is submitted, only the last desc would generate irq -> call back
If IDLE, issue_pending_list start pending_list, transforming pendlist to running list
If RUN, irq will start pending list
5. test
5.1 pxa3xx_nand on pxa910
5.2 insmod dmatest.ko (threads_per_chan=y)
By default drivers/dma/dmatest.c test every channel and test memcpy with 1 threads per channel
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Add a DMA engine driver for the TI EDMA controller. This driver
is implemented as a wrapper around the existing DaVinci private
DMA implementation. This approach allows for incremental conversion
of each peripheral driver to the DMA engine API. The EDMA driver
supports slave transfers but does not yet support cyclic transfers.
Signed-off-by: Matt Porter <mporter@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Pull ARM DMA engine updates from Russell King:
"This looks scary at first glance, but what it is is:
- a rework of the sa11x0 DMA engine driver merged during the previous
cycle, to extract a common set of helper functions for DMA engine
implementations.
- conversion of amba-pl08x.c to use these helper functions.
- addition of OMAP DMA engine driver (using these helper functions),
and conversion of some of the OMAP DMA users to use DMA engine.
Nothing in the helper functions is ARM specific, so I hope that other
implementations can consolidate some of their code by making use of
these helpers.
This has been sitting in linux-next most of the merge cycle, and has
been tested by several OMAP folk. I've tested it on sa11x0 platforms,
and given it my best shot on my broken platforms which have the
amba-pl08x controller.
The last point is the addition to feature-removal-schedule.txt, which
will have a merge conflict. Between myself and TI, we're planning to
remove the old TI DMA implementation next year."
Fix up trivial add/add conflicts in Documentation/feature-removal-schedule.txt
and drivers/dma/{Kconfig,Makefile}
* 'dmaengine' of git://git.linaro.org/people/rmk/linux-arm: (53 commits)
ARM: 7481/1: OMAP2+: omap2plus_defconfig: enable OMAP DMA engine
ARM: 7464/1: mmc: omap_hsmmc: ensure probe returns error if DMA channel request fails
Add feature removal of old OMAP private DMA implementation
mtd: omap2: remove private DMA API implementation
mtd: omap2: add DMA engine support
spi: omap2-mcspi: remove private DMA API implementation
spi: omap2-mcspi: add DMA engine support
ARM: omap: remove mmc platform data dma_mask and initialization
mmc: omap: remove private DMA API implementation
mmc: omap: add DMA engine support
mmc: omap_hsmmc: remove private DMA API implementation
mmc: omap_hsmmc: add DMA engine support
dmaengine: omap: add support for cyclic DMA
dmaengine: omap: add support for setting fi
dmaengine: omap: add support for returning residue in tx_state method
dmaengine: add OMAP DMA engine driver
dmaengine: sa11x0-dma: add cyclic DMA support
dmaengine: sa11x0-dma: fix DMA residue support
dmaengine: PL08x: ensure all descriptors are freed when channel is released
dmaengine: PL08x: get rid of write only pool_ctr and free_txd locking
...
|
|
|
|
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Initialize the vchan struct, and use the provided spinlock rather than
our own.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Split the virtual slave channel DMA support from the sa11x0 driver so
this code can be shared with other slave DMA engine drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Add support for two-channel dma under dmaengine
support: mmp-adma and pxa910-squ
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Leo Yan <leoy@marvell.com>
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Add dmaengine based NVIDIA's Tegra APB DMA driver.
This driver support the slave mode of data transfer from
peripheral to memory and vice versa.
The driver supports for the cyclic and non-cyclic mode
of data transfer.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
enable the mxs-dma for imx6q.
Also remove the unused header file.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
This can get rid of the mach-dependency.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Huang Shijie <b32955@freescale.com>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
|
|
Remove SoC dependency and make it generic for every Atmel ARM AT91. That will
allow to select this driver for newer chips. Keep dependency on AT91 because of
the use of an header file located in include/mach directory.
Modify the comment to reflect this.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Pull slave-dmaengine update from Vinod Koul:
"This includes the cookie cleanup by Russell, the addition of context
parameter for dmaengine APIs, more arm dmaengine driver cleanup by
moving code to dmaengine, this time for imx by Javier and pl330 by
Boojin along with the usual driver fixes."
Fix up some fairly trivial conflicts with various other cleanups.
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (67 commits)
dmaengine: imx: fix the build failure on x86_64
dmaengine: i.MX: Fix merge of cookie branch.
dmaengine: i.MX: Add support for interleaved transfers.
dmaengine: imx-dma: use 'dev_dbg' and 'dev_warn' for messages.
dmaengine: imx-dma: remove 'imx_dmav1_baseaddr' and 'dma_clk'.
dmaengine: imx-dma: remove unused arg of imxdma_sg_next.
dmaengine: imx-dma: remove internal structure.
dmaengine: imx-dma: remove 'resbytes' field of 'internal' structure.
dmaengine: imx-dma: remove 'in_use' field of 'internal' structure.
dmaengine: imx-dma: remove sg member from internal structure.
dmaengine: imx-dma: remove 'imxdma_setup_sg_hw' function.
dmaengine: imx-dma: remove 'imxdma_config_channel_hw' function.
dmaengine: imx-dma: remove 'imxdma_setup_mem2mem_hw' function.
dmaengine: imx-dma: remove dma_mode member of internal structure.
dmaengine: imx-dma: remove data member from internal structure.
dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c
dmaengine: at_hdmac: add slave config operation
dmaengine: add context parameter to prep_slave_sg and prep_dma_cyclic
dmaengine/dma_slave: introduce inline wrappers
dma: imx-sdma: Treat firmware messages as warnings instead of erros
...
|
|
commit 6bd081277ea0 "dmaengine: imx-dma: merge old dma-v1.c with
imx-dma.c" removed the dependency in config for the imx dma driver,
whereas it should depend on ARCH_MXS
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
It is mainly a simple merge changing the prefix of some
functions to fit the imx-dma namings.
As there are no users of the old dma-v1.c api we can safely
remove this file.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Currently there were two part of DMAC PL330 driver for
support old styled s3c-pl330 which has been merged into
drivers/dma/pl330.c driver. Actually, there is no reason
to separate them now.
Basically this patch merges arch/arm/common/pl330.c into
drivers/dma/pl330.c driver and removes useless exported
symbol, externed function and so on.
The newer pl330 driver tested on SMDKV310 and SMDK4212 boards
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
Add support for the SA-11x0 DMA driver, which replaces the private
API version in arch/arm/mach-sa1100/dma.c.
We model this as a set of virtual DMA channels, one for each request
signal, and assign the virtual DMA channel to a physical DMA channel
when there is work to be done. This allows DMA users to claim their
channels, and hold them while not in use, without affecting the
availability of the physical channels.
Another advantage over this approach, compared to the private version,
is that a channel can be reconfigured on the fly without having to
release and re-request it - which for the IrDA driver, allows us to
use DMA for SIR mode transmit without eating up three physical
channels. As IrDA is half-duplex, we actually only need one physical
channel, and this architecture allows us to achieve that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
[fixed direction enums and cyclic api based on changes
already merged]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
ML7831 is companion chip for Intel Atom E6xx series.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor
Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
This patch updates following 3 items.
1. Removes unneccessary code.
2. Add AMBA, PL330 configuration
3. Change the meaning of 'peri_id' variable
from PL330 event number to specific dma id by user.
Signed-off-by: Boojin Kim <boojin.kim@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The ep93xx DMA controller has 10 independent memory to peripheral (M2P)
channels, and 2 dedicated memory to memory (M2M) channels. M2M channels can
also be used by SPI and IDE to perform DMA transfers to/from their memory
mapped FIFOs.
This driver supports both M2P and M2M channels with DMA_SLAVE, DMA_CYCLIC and
DMA_MEMCPY (M2M only) capabilities.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As a side effect this makes IMX_DMA selectable on i.MX21 again, because
the symbol ARCH_MX21 doesn't exist (MACH_MX21 would have been more correct).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This driver will now be used in atleast two platforms AVR32 & ARM. And there is
no actual hardware dependency of this driver over AVR32 or ARM. So this
dependency can be removed altogether.
Also dw_dmac driver uses clk framework and must have compilation dependency on
HAVE_CLK
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds dma support for Freescale MXS-based SoC i.MX23/28,
including apbh-dma and apbx-dma.
* apbh-dma and apbx-dma are supported in the driver as two mxs-dma
instances.
* apbh-dma is different between mx23 and mx28, hardware version
register is used to differentiate.
* mxs-dma supports pio function besides data transfer. The driver
uses dma_data_direction DMA_NONE to identify the pio mode, and
steals sgl and sg_len to get pio words and numbers from clients.
* mxs dmaengine has some very specific features, like sense function
and the special NAND support (nand_lock, nand_wait4ready). These
are too specific to implemented in generic dmaengine driver.
* The driver refers to imx-sdma and only a single descriptor is
statically assigned to each channel.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (63 commits)
ARM: PL08x: cleanup comments
Update CONFIG_MD_RAID6_PQ to CONFIG_RAID6_PQ in drivers/dma/iop-adma.c
ARM: PL08x: fix a warning
Fix dmaengine_submit() return type
dmaengine: at_hdmac: fix race while monitoring channel status
dmaengine: at_hdmac: flags located in first descriptor
dmaengine: at_hdmac: use subsys_initcall instead of module_init
dmaengine: at_hdmac: no need set ACK in new descriptor
dmaengine: at_hdmac: trivial add precision to unmapping comment
dmaengine: at_hdmac: use dma_address to program DMA hardware
pch_dma: support new device ML7213 IOH
ARM: PL08x: prevent dma_set_runtime_config() reconfiguring memcpy channels
ARM: PL08x: allow dma_set_runtime_config() to return errors
ARM: PL08x: fix locking between prepare function and submit function
ARM: PL08x: introduce 'phychan_hold' to hold on to physical channels
ARM: PL08x: put txd's on the pending list in pl08x_tx_submit()
ARM: PL08x: rename 'desc_list' as 'pend_list'
ARM: PL08x: implement unmapping of memcpy buffers
ARM: PL08x: store prep_* flags in async_tx structure
ARM: PL08x: shrink srcbus/dstbus in txd structure
...
|
|
Support new device OKI SEMICONDUCTOR's ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use.
The ML7213 is companion chip for Intel Atom E6xx series.
The ML7213 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
MPC8308 has pretty much the same DMA controller as MPC5121 and
this patch adds support for MPC8308 to the mpc512x_dma driver.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Product codenames are OK, but once an actual product name is available,
it should be referenced as well.
http://ark.intel.com/chipset.aspx?familyID=52499
Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The majority of drivers in drivers/dma/ will never establish cross
channel operation chains and do not need the extra overhead in struct
dma_async_tx_descriptor. Make channel switching opt-in by default.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Ira Snyder <iws@ovro.caltech.edu>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
|
|
This driver is currently implemented as a user to the old i.MX
DMA API. This allows us to convert each user of the old API to
the dmaengine API one by one. Once this is done the old DMA
driver can be merged into the i.MX dmaengine driver.
V2: remove some debug leftovers and unused variables
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch adds support for the Freescale i.MX SDMA engine.
The SDMA engine is a scatter/gather DMA engine which is implemented
as a seperate coprocessor. SDMA needs its own firmware which is
requested using the standard request_firmware mechanism. The firmware
has different entry points for each peripheral type, so drivers
have to pass the peripheral type to the DMA engine which in turn
picks the correct firmware entry point from a table contained in
the firmware image itself.
The original Freescale code also supports support for transfering
data to the internal SRAM which needs different entry points to
the firmware. Support for this is currently not implemented. Also,
support for the ASRC (asymmetric sample rate converter) is skipped.
I took a very simple approach to implement dmaengine support. Only
a single descriptor is statically assigned to a each channel. This
means that transfers can't be queued up but only a single transfer
is in progress. This simplifies implementation a lot and is sufficient
for the usual device/memory transfers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Linus Walleij <linus.ml.walleij@gmail.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This creates a DMAengine driver for the ARM PL080/PL081 PrimeCells
based on the implementation earlier submitted by Peter Pearse.
This is working like a charm for memcpy and slave DMA to the PL011
PrimeCell on the PB11MPCore.
This DMA controller is used in mostly unmodified form in the ARM
RealView and Versatile platforms, in the ST-Ericsson Nomadik, and
in the ST SPEAr platform.
It has been converted to use the header from the Samsung PL080
derivate instead of its own defintions. The Samsungs have a custom
driver in their mach-* folders though, atleast we can share the
register definitions.
Cc: Peter Pearse <peter.pearse@arm.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[GFP_KERNEL to GFP_NOWAIT in pl08x_prep_dma_memcpy]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Conflicts:
arch/arm/Kconfig
arch/arm/mm/Kconfig
|
|
Topcliff PCH is the platform controller hub that is going to
be used in Intel's upcoming general embedded platforms. This
adds the driver for Topcliff PCH DMA controller. The DMA
channels are strictly for device to host or host to device
transfers and cannot be used for generic memcpy.
Signed-off-by: Yong Wang <yong.y.wang@intel.com>
[kill GFP_ATOMIC, kill __raw_{read|write}l, locking fixlet]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This patch add DMA drivers for DMA controllers in Langwell chipset
of Intel(R) Moorestown platform and DMA controllers in Penwell of
Intel(R) Medfield platfrom
This patch adds support for Moorestown DMAC1 and DMAC2 controllers.
It also add support for Medfiled GP DMA and DMAC1 controllers.
These controllers supports memory to peripheral and peripheral to
memory transfers. It support only single block transfers.
This driver is based on Kernel DMA engine
Anyone who wishes to use this controller should use DMA engine APIs
This controller exposes DMA_SLAVE capabilities and notifies the client drivers
of DMA transaction completion
Config option required to be enabled CONFIG_INTEL_MID_DMAC=y
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
Add DMA Engine API driver for the PL330 DMAC.
This driver is supposed to be reusable by various
platforms that have one or more PL330 DMACs.
Atm, DMA_SLAVE and DMA_MEMCPY capabilities have been
implemented.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@stericsson.com>
[dan.j.williams@intel.com: missing slab.h and ->device_control() fixups]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
|
|
This is a straightforward driver for the ST-Ericsson DMA40 DMA
controller found in U8500, implemented akin to the existing
COH 901 318 driver.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidh Kasagar <srinidhi.kasagar@stericsson.com>
Cc: STEricsson_nomadik_linux@list.st.com
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Enable the shdma dmaengine driver on SH-Mobile ARM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
