summaryrefslogtreecommitdiff
path: root/drivers/hwmon
AgeCommit message (Collapse)Author
2010-11-15hwmon: (w83795) Check for BEEP pin availabilityJean Delvare
On the W83795ADG, there's a single pin for BEEP and OVT#, so you can't have both. Check the configuration and don't create beep attributes when BEEP pin is not available. The W83795G has a dedicated BEEP pin so the functionality is always available there. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-15hwmon: (w83795) Clear intrusion alarm immediatelyJean Delvare
When asked to clear the intrusion alarm, do so immediately. We have to invalidate the cache to make sure the new status will be read. But we also have to read from the status register once to clear the pending alarm, as writing to CLR_CHS surprising won't clear it automatically. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-15hwmon: (w83795) Read the intrusion state properlyJean Delvare
We can't read the intrusion state from the real-time alarm registers as we do for all other alarm flags, because real-time alarm bits don't stick (by definition) and the intrusion state has to stick until explicitly cleared (otherwise it has little value.) So we have to use the interrupt status register instead, which is read from the same address but with a configuration bit flipped in another register. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-15hwmon: (w83795) Print the actual temperature channels as sourcesJean Delvare
Don't expose raw register values to user-space. Decode and encode temperature channels selected as temperature sources as needed. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-15hwmon: (w83795) List all usable temperature sourcesJean Delvare
Temperature sources are not correlated directly with temperature channels. A look-up table is required to find out which temperature sources can be used depending on which temperature channels (both analog and digital) are enabled. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-15hwmon: (w83795) Expose fan control methodJean Delvare
Expose fan control method (DC vs. PWM) using the standard sysfs attributes. I've made it read-only as the board should be wired for a given mode, the BIOS should have set up the chip for this mode, and you shouldn't have to change it. But it would be easy enough to make it changeable if someone comes up with a use case. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-15hwmon: (w83795) Fix fan control mode attributesJean Delvare
There were two bugs: * Speed cruise mode was improperly reported for all fans but fan1. * Fan control method (PWM vs. DC) was mixed with the control mode. It will be added back as a separate attribute, as per the standard sysfs interface. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-15hwmon: (lm95241) Check validity of input valuesJean Delvare
This clears the following build-time warnings I was seeing: drivers/hwmon/lm95241.c: In function "set_interval": drivers/hwmon/lm95241.c:132:15: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result drivers/hwmon/lm95241.c: In function "set_max2": drivers/hwmon/lm95241.c:278:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result drivers/hwmon/lm95241.c: In function "set_max1": drivers/hwmon/lm95241.c:277:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result drivers/hwmon/lm95241.c: In function "set_min2": drivers/hwmon/lm95241.c:249:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result drivers/hwmon/lm95241.c: In function "set_min1": drivers/hwmon/lm95241.c:248:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result drivers/hwmon/lm95241.c: In function "set_type2": drivers/hwmon/lm95241.c:220:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result drivers/hwmon/lm95241.c: In function "set_type1": drivers/hwmon/lm95241.c:219:1: warning: ignoring return value of "strict_strtol", declared with attribute warn_unused_result This also fixes a small race in set_interval() as a side effect: by working with a temporary local variable we prevent data->interval from being accessed at a time it contains the interval value in the wrong unit. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Davide Rizzo <elpa.rizzo@gmail.com>
2010-11-15hwmon: Change mail address of Hans J. KochHans J. Koch
My old mail address doesn't exist anymore. This changes all occurrences to my new address. Signed-off-by: Hans J. Koch <hjk@hansjkoch.de> Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-11-11hwmon: (gpio-fan) Fix fan_ctrl_init error pathAxel Lin
In current implementation, the sysfs entries is not removed before return -ENODEV. Creating the sysfs attribute should be the last thing done by the function, after all the rest has been successful. Otherwise there is a small window during which user-space can access the attribute but the driver isn't ready to deal with the requests. Fix it by moving sysfs_create_group to be the last thing done by the function. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Simon Guinot <sguinot@lacie.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-11hwmon: (ad7414) Return proper error code for ad7414_probe()Axel Lin
Return proper error if i2c_check_functionality reports the adapter does not support the capability we need. Also remove unneeded initialization for err variable. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-11hwmon: (adt7470) Return proper error code for adt7470_probe()Axel Lin
Signed-off-by: Axel Lin <axel.lin@gmail.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-05hwmon: (ltc4261) Fix error message formatJean Delvare
adapter->id is deprecated and not set by any adapter driver, so this was certainly not what the author wanted to use. adapter->nr maybe, but as dev_err() already includes this value, as well as the client's address, there's no point repeating them. Better print a simple error message in plain English words. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-11-05hwmon: (ltc4261) Add missing newline in debug messageGuenter Roeck
Reported-by: Joe Perches <joe@perches.com> Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com> Acked-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (it87) Add support for the IT8721F/IT8758EJean Delvare
Add support for the IT8721F/IT8758E. These new chips differ from the older IT87xxF chips in the following ways: * ADC LSB is 12 mV instead of 16 mV. * PWM values are 8-bit instead of 7-bit. There are other minor changes we don't have to care about in the driver. Another change is that we will handle internal voltage scaling in the driver instead of delegating the work to user-space. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (it87) Move conversion functionsJean Delvare
Move conversion functions until after structure defintions. This is needed for future changes which make use of the structures in the conversion funtcions. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: Remove many EXPERIMENTAL flagsJean Delvare
Remove the dependency on EXPERIMENTAL for all drivers which are in the kernel tree for a long time, are known to work properly and for which we have documentation. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Corentin Labbe <corentin.labbe@geomatys.fr> Cc: Riku Voipio <riku.voipio@iki.fi> Cc: Juerg Haefliger <juergh@gmail.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (lm85) Add support for ADT7468 high-frequency PWM modeJean Delvare
The ADT7468 supports a high-frequency PWM output mode where all PWM outputs are driven by a 22.5 kHz clock. Add support for this mode, and document it, as it may surprise the user that setting one PWM output frequency also affects the other PWM outputs. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (lm85) Document the ADT7468 as supportedJean Delvare
Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (lm85) Fix ADT7468 frequency tableJean Delvare
The ADT7468 uses the same frequency table as the ADT7463. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: stable@kernel.org Cc: Darrick J. Wong <djwong@us.ibm.com> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: I2C addresses are constantJean Delvare
We can mark normal_i2c const. Almost all drivers do that already, so fix the 3 remaining ones before they are used as (bad) examples for new drivers. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: George Joseph <george.joseph@fairview5.com> Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28Move ams driver to macintoshJean Delvare
The ams driver isn't a hardware monitoring driver, so it shouldn't live under driver/hwmon. drivers/macintosh seems much more appropriate, as the driver is only useful on PowerBooks and iBooks. Signed-off-by: Jean Delvare <khali@linux-fr.org> Cc: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Stelian Pop <stelian@popies.net> Cc: Michael Hanselmann <linux-kernel@hansmi.ch> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca>
2010-10-28hwmon: (pcf8591) Don't attempt to detect devicesJean Delvare
The PCF8591 can't be detected, don't even try. There are plenty of other means to instantiate i2c devices these days. Signed-off-by: Jean Delvare <khali@linux-fr.org> Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Aurelien Jarno <aurelien@aurel32.net>
2010-10-28hwmon: (pcf8591) Register as a hwmon deviceJean Delvare
Register PCF8591 devices as hwmon devices. There's little point in implementing the standard sysfs interface if we don't register it in a way libsensors will pick it. Signed-off-by: Jean Delvare <khali@linux-fr.org> Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com> Cc: Aurelien Jarno <aurelien@aurel32.net>
2010-10-28hwmon: (w83795) Use standard attributes for chassis intrusionJean Delvare
Follow the standard attribute naming for the chassis intrusion feature. I couldn't test the beeping (my board apparently doesn't do that) but the alarm works fine. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Exclude fan control feature by defaultJean Delvare
The fan control feature of the w83795 driver is insufficiently reviewed and tested for public consumption at this time, so make it optional and disabled by default. We will change the default when review and testing is deemed sufficient. Ultimately the option will go away. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Add myself as co-author and maintainerJean Delvare
I've made so many changes to the w83795 driver that it's only fair to list myself as a co-author. I'll also maintain the driver for some time. There's more work needed on the driver for sure. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) More style cleanupsJean Delvare
Cleanups suggested by Guenter Roeck, falling into 4 categories: * Swapping test orders, because if (var == CONSTANT) is much easier to read than if (CONSTANT == var). * Simplifying comparisons with 0. * Dropping unneeded masks. * Dropping unneeded parentheses and curly braces. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Fix LSB reading of voltage limitsJean Delvare
Wrong index caused the wrong register value to be read, resulting in random LSB for voltage limits. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Use dev_get_drvdata() where possibleJean Delvare
When we don't need the client pointer, calling dev_get_drvdata() is more efficient that calling to_i2c_client() and then i2c_get_clientdata(). Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Delay reading pwm config registersJean Delvare
Wait until we need the pwm config register values, instead of pre-reading them. This saves over 1 second on modprobe on my test system. Obviously this time is added when first accessing pwm config attributes, however not everybody will use them, so it seems unfair to slow down driver loading (and thus boot) for an optional feature. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Delay reading limit registersJean Delvare
Wait until we need the limit register values, instead of pre-reading them. This saves 544 ms on modprobe on my test system. Obviously this time is added when first running "sensors" or any other monitoring application, but I think it is better than slowing down the boot. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Move register reads to dedicated functionsJean Delvare
Move initial register reads out of probe, to dedicated functions. This makes the code clearer, and will be needed if we want to delay calling these functions until they are needed, or want to call them periodically. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Pack similar register readsJean Delvare
Pack similar register reads using for loops. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Make W83795_REG_PWM more efficientJean Delvare
Cascaded conditionals are inefficient. Reorder the fields so that PWM register addresses can be computed more efficiently. Signed-off-by: Jean Delvare <khali@linux-fr.org> Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
2010-10-28hwmon: (w83795) Don't pre-read values we'll update laterJean Delvare
There is no point in reading registers during initialization if we will refresh the values in the update function later. This is only slowing down the driver loading with no benefit, stop doing it. This change saves 480 ms on driver load on my test system. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Simplify temperature sensor type handlingJean Delvare
All 3 temperature sensor type sysfs functions (show_temp_mode, store_temp_mode and show_dts_mode) can be simplified. We don't create these files when the correponding input isn't in temperature monitoring mode, so there is no point in handling that case. Likewise, we don't allow changing inputs from temperature to voltage, so the code handling this case is dead and can be removed. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Drop _NUM constantsJean Delvare
Consistently use ARRAY_SIZE() to control for loops. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Drop REST_VLT_BEGIN/ENDJean Delvare
Get rid of REST_VLT_BEGIN and REST_VLT_END, they don't make the code more readable. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Fix parity checksJean Delvare
x % 1 is obviously wrong, as it always evaluates to 0. You want x % 2, or x & 1, for parity checking. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Get rid of VRLSB_SHIFTJean Delvare
VRLSB_SHIFT is a non-sense, the actual shift depends on the sensor type (fans need 4, other sensors need 6). Get rid of it to prevent any confusion. Also get rid of the useless masking, the meaningful bits are always the MSb so there's nothing to mask out after shifting. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Avoid reading the same register twiceJean Delvare
Shorten driver load time by avoiding duplicate register access during initialization. This saves 112 ms on modprobe on my test system. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Rework beep_enable implementationJean Delvare
Handle beep_enable just like all other beep bits. It doesn't need anything special, so let's avoid redundant code. This also saves a duplicate register read at initialization time. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Report PECI agent Tbase valuesJean Delvare
On systems with PECI, report PECI agent Tbase temperature values. This is informative only. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Properly handle negative temperaturesJean Delvare
The temperature registers hold regular 2's complement values, no need to add any arithmetics. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Rename temperature limit attributesJean Delvare
Follow the standard for temperature limit attribute naming, so that libsensors will pick the values. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Fix PWM duty cycle frequency attributesJean Delvare
The PWM duty cycle frequenty attributes are improperly named (fanN_div instead of pwmN_div) and contain raw values instead of actual frequencies. Rename them and fix their contents. Also improve the logic when the user asks for a new frequency, to always pick the closest supported frequency. The algorithm could certainly be optimized, but the operation is infrequent enough that I don't think it's worth the effort. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Add support for dynamic in0-2 limitsJean Delvare
The W83795G can be configured to set the in0, in1 and/or in2 voltage limits dynamically based on VID input pins. Switch the respective sysfs attributes to read-only. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Fix LSB reading of fan speedsJean Delvare
Misplaced parentheses caused the wrong register value to be read, resulting in random LSB for fan speed values and limits. Signed-off-by: Jean Delvare <khali@linux-fr.org>
2010-10-28hwmon: (w83795) Clean up probe functionJean Delvare
* The data structure is zalloc'd, so no need to set individual fields to 0 explicitly. * Refactor the handling of pins that can be used for either temperature or voltage monitoring. * Misc other clean-ups. Signed-off-by: Jean Delvare <khali@linux-fr.org>