| Age | Commit message (Collapse) | Author |
|---|
|
It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode. The corresponding
registers are then read-only. If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Minor formatting cleanup]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values. Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.
The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.
Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.
This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
For the F75387, the register holding the current PWM duty cycle value is
r/o; changing it requires writing to the fan expect register instead.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Simplified function parameters]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Temperature history is reset by writing 0x8000 into the peak temperature
register, not 0xffff.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
An error while creating sysfs attribute files in the driver's probe function
results in an error abort, but already created files are not removed. This patch
fixes the problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Cc: Dirk Eibach <eibach@gdsys.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Initialize PPR register for both channels, and set correct PPR register bits.
Also remove unnecessary variable initializations.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: Merged two patches into one]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Roland Stigge <stigge@antcom.de>
|
|
RPM calculation from tachometer value does not depend on PPR.
Also, do not report negative RPM values.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: do not report negative RPM values]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Roland Stigge <stigge@antcom.de>
|
|
Treat pwmX as a measured value, not as a (mostly static) limit value, so
that it is updated more frequently from the device register.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
In order to extract the high byte of the 16-bit word, shift the word to
the right, not to the left.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Unlike the other chips supported by this driver, the F75387 stores the
pwm_mode in register F75375_REG_FAN_TIMER, not F75375_REG_CONFIG1.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
In order to enable temperature mode aka automatic mode for the F75373 and
F75375 chips, the two FANx_MODE bits in the fan configuration register
need be set to 01, not 10.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Commit ec3e5a16446fef1891611fe3bdfa5954d1ddf5e4 slipped in some duplicate code.
Remove it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
NCT6776F can select fan input pins for fans 3 to 5 with a secondary set of
chip register bits. Check that second set of bits in addition to the first set
to detect if fans 3..5 are monitored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
NCT6776F only supports pwm mode for pwm2 and pwm3. Return error if an attempt
is made to set those pwm channels to DC mode.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org # 3.0+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
When no platform data was supplied, returned error code was 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: stable@vger.kernel.org # 2.6.32+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Properly clamp temperature limits set by the user. Without this fix,
attempts to write temperature limits above the maximum supported by
the chip (255 degrees Celsius) would arbitrarily and unexpectedly
result in the limit being set to 0 degree Celsius.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Fix almost all coding style issues except for the multi-line macro errors,
which do not really apply since the macros are not multi-line statements
but declarations.
Based on merged patch series from Zac Storer; fixed remaining checkpatch
errors and warnings.
Cc: Zac Storer <zac.3.14159@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Until we get a datasheet for the IT8728F, treat it as fully compatible
with the IT8721F, as it seems to work reasonably well.
This closes kernel bug #27262.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Many functions in the coretemp driver lack a proper section
annotation. Add them to let the kernel free the memory after
initialization when possible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Durgadoss R <durgadoss.r@intel.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
|
|
When writing the update_interval attribute, the parameter value was
not range checked, which could cause an integer overflow and result
in an arbitrary update interval. Fix by limiting the value range to
<0, 100000>.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The LM96163 has an extended lookup table with 12 entries instead of 8,
add support for that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The LM63 and compatible devices have a lookup table to control the fan
speed automatically. Expose it in sysfs. Values are cached for 5
seconds, independently of the other register values to avoid slowing
down "sensors". We might make the table values writable in the future.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
What was true of the LM63 doesn't apply to the LM64.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
On the LM64, the tachometer function has a dedicated pin and fan speed
monitoring is always enabled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
On LM96163, the external temperature sensor type is configurable to
either a thermal diode or a 3904 transistor. The chip reports a wrong
temperature if misconfigured. Add writable attribute to support it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The update interval is configurable on LM63 and compatibles. Add
support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
On LM64, the external critical temperature limit is always writable. On LM96163,
it is writable if the chip is configured for it. Add conditional support for
writing the register dependent on chip type and configuration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
LM96163 supports unsigned upper limits for the external temperature sensor.
Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
LM96163 is an enhanced version of LM63 with improved PWM resolution. Add chip
detection code as well as support for improved PWM resolution if the chip is
configured to use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
LM63 and compatibles support a temperature offset register for the external
temperature sensor. Add support for it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This patch fixed the inconsistent max1111 sysfs interface as pointed
out by Jean Delvare:
It was pointed to me that the max1111 driver doesn't implement the
standard sysfs interface for hwmon drivers (as described in
Documentation/hwmon/sysfs-interface). It exports files adc[0-3]_in,
which
aren't part of the standard interface. Presumably these should be
renamed to in[0-3]_input. Renaming them is probably not sufficient
though, as I see no scaling done in the driver. As the MAX1111 chip has
a documented full scale of 2.048V, I take it that the LSB of the ADC
has a weight of 8 mV. Exporting raw register values to user-space is
not OK.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
For historical reasons, we allow module_param(bool) to take an int (or
an unsigned int). That's going away.
A few drivers really want an int: they set it to -1 and a parameter
will set it to 0 or 1. This sucks: reading them from sysfs will give
'Y' for both -1 and 1, but if we change it to an int, then the users
might be broken (if they did "param" instead of "param=1").
Use a new 'bint' parser for them.
(ntfs has a different problem: it needs an int for debug_msgs because
it's also exposed via sysctl.)
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Cc: Christoph Raisch <raisch@de.ibm.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux390@de.ibm.com
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: lm-sensors@lm-sensors.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: linux-ntfs-dev@lists.sourceforge.net
Cc: alsa-devel@alsa-project.org
Acked-by: Takashi Iwai <tiwai@suse.de> (For the sound part)
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> (For the hwmon driver)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
max1111.c: fix checkpatch warning
hwmon: (lm75) fix checkpatch warnings
hwmon: (lm80) fix checkpatch messages
hwmon: replaced strict_str* with kstr*
hwmon: (lm75) fix checkpatch warning
hwmon: (lm75) added error handling
hwmon: (ltc4261) set data->valid to 0 if error
hwmon: (f75375s) Add support for F75387SG/RG
hwmon: (f75375s) Disable setting DC fan control mode for F75373
hwmon: (f75375s) Initialize pwmX_mode and pwmX_enable if there is no platform data
hwmon: (f75375s) Fix value range for PWM modes
hwmon: (f75375s) Use standard sysfs attribute names
hwmon: (f75375s) Fix checkpatch errors and warnings
hwmon: (pmbus/zl6100) Only instantiate external temperature sensor if enabled
hwmon: (pmbus/zl6100) Add support for Ericsson BMR45[0,1] and BMR46[2,3,4]
hwmon: (pmbus/zl6100) Add support for ZL2005
hwmon: (pmbus/adm1275) Validate device ID
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Skip cpus with apic-ids >= 255 in !x2apic_mode
x86, x2apic: Allow "nox2apic" to disable x2apic mode setup by BIOS
x86, x2apic: Fallback to xapic when BIOS doesn't setup interrupt-remapping
x86, acpi: Skip acpi x2apic entries if the x2apic feature is not present
x86, apic: Add probe() for apic_flat
x86: Simplify code by removing a !SMP #ifdefs from 'struct cpuinfo_x86'
x86: Convert per-cpu counter icr_read_retry_count into a member of irq_stat
x86: Add per-cpu stat counter for APIC ICR read tries
pci, x86/io-apic: Allow PCI_IOAPIC to be user configurable on x86
x86: Fix the !CONFIG_NUMA build of the new CPU ID fixup code support
x86: Add NumaChip support
x86: Add x86_init platform override to fix up NUMA core numbering
x86: Make flat_init_apic_ldr() available
|
|
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Fix checkpatch warnings in lm75.h include file
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Fixed all checkpatch messages except
simple_strto* -> kstr*
This will be addressed in a separate patch
Also left one line-too-long message as it was only a
little bit too long and would become less readable
compile-tested: no warnings or errors
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
replaced strict_strtol with kstrtol and
replaced strict_strtuol with kstrtuol
This satisfies checkpatch -f
Compile tested only: no warnings or errors given
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Fixed this:
WARNING: strict_strtol is obsolete, use kstrtol instead
+ error = strict_strtol(buf, 10, &temp);
by replacing strict_strtol with kstrtol.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Add error handling so if lm75_update_device fails
an error is returned when reading the value through sysfs.
This is closely modeled after the way this is handled in ltc4261.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
If there is an error it is better to set data->valid to 0
so the next call to ltc4261_update_device will always be
executed.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Fintek F75387SG/RG is mostly compatible to F75373/F75375. Add support for it
to the F75375S driver.
Fan support for F75387SG/RG has been implemented but not tested.
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
F75373 does not support DC (linear voltage) fan control mode, so don't let
the user set it.
Cc: Riku Voipio <riku.voipio@iki.fi>
Reviewed-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
platform data
pwmX_mode and pwmX_enable are not initialized if no platform data is provided to
the driver. Read chip configuration at driver initialization time and initialize
attributes to reflect chip configuration.
Cc: Riku Voipio <riku.voipio@iki.fi>
Reviewed-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Accepted value range for PWM modes was 0..4, even though only 0..3 is
subsequently used. Limit permitted value range to 0..3 to avoid unpredictable
behavior.
Cc: Riku Voipio <riku.voipio@iki.fi>
Reviewed-by: Bjoern Gerhart <oss@extracloud.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
