| Age | Commit message (Collapse) | Author |
|---|
|
Result of DIV_ROUND_CLOSEST is undefined for negative dividends if the divisor
variable type is unsigned. Fix by declaring divisor as signed variable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
If an LM73 device does not exist on an I2C bus, attempts to communicate
with the device result in an error code returned from the i2c read/write
functions. The current lm73 driver casts that return value from a s32
type to a s16 type, then converts it to a temperature in celsius.
Because negative temperatures are valid, it is difficult to distinguish
between an error code printed to the response buffer and a negative
temperature recorded by the sensor.
The solution is to evaluate the return value from the i2c functions
before performing any temperature calculations. If the i2c function did
not succeed, the error code should be passed back through the virtual
file system layer instead of being printed into the response buffer.
Before:
$ cat /sys/class/hwmon/hwmon0/device/temp1_input
-46
After:
$ cat /sys/class/hwmon/hwmon0/device/temp1_input
cat: read error: No such device or address
Signed-off-by: Chris Verges <kg4ysn@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since family 11h processors, AMD is exclusively using 7-bit VID codes
transmitted using a serial protocol over two pins (clock and data.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: David Hubbard <david.c.hubbard@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
Extend support for reporting and selecting PECI temperature sensors
to IT8718, IT8720, IT8782, and IT8783. For IT8721, report the sensor
type for temp2 as Intel PECI (6) if the chip is configured to report
the PCH temperature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
IT8721 and IT8728 support Intel PECI temperature reporting. Each sensor
can be programmed to display the temperature reported on the PECI interface.
If configured for Intel PECI, the driver reported the wrong sensor type for
the respective thermal sensor. Fix the code to correctly report it as
"Intel PECI (6)".
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
This simplifies the code, improves runtime performance, reduces
code size (about 280 bytes on x86_64), and makes it easier
to add support for new devices.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Fix checkpatch error:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Fix the respective checkpatch warnings.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Also unify fan functions to use the same code for 8 and 16 bit fans.
This patch reduces code size by approximately 1,200 bytes on x86_64.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The macro name show_sensor_offset is confusing since it related to the sensor
type, not an offset - even more so when we introduce offset attributes later on.
Replace it with direct definitions, and replace the show_sensor/set_sensor
function names with show_temp_type/set_temp_type. This also resolves a
checkpatch error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Reduces code size (more than 600 bytes on x86_64),
and gets rid of some checkpatch errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Cleaner code, fewer checkpatch errors, and reduced code size
(saves more than 500 bytes on x86-64).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The smatch static code analyzer complains:
drivers/hwmon/w83627ehf.c:911 w83627ehf_update_device() error: buffer overflow 'W83627EHF_REG_TEMP_OFFSET' 3 <= 8
drivers/hwmon/w83627ehf.c:909 w83627ehf_update_device() error: buffer overflow 'data->temp_offset' 3 <= 8
drivers/hwmon/w83627ehf.c:2672 w83627ehf_resume() error: buffer overflow 'W83627EHF_REG_TEMP_OFFSET' 3 <= 8
drivers/hwmon/w83627ehf.c:2673 w83627ehf_resume() error: buffer overflow 'data->temp_offset' 3 <= 8
A deeper analysis of the code shows that these are false positives, as
only the lower 3 bits of data->have_temp_offset can be set so the
write is never attempted with i >= 3. However this shows that the code
isn't very robust and future changes could easily introduce a buffer
overflow. So let's add a safety check to prevent that and make smatch
happy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <PeterHuewe@gmx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
Only the W83627HF could be accessed through I2C. All other supported
chips are LPC-only, so they do not have I2C address registers. Don't
write to nonexistent or reserved registers on these chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
On suspend some register values are lost, most notably the Value RAM
areas but also other limits and settings. Restore them on resume.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
On suspend some register values are lost, most notably the Value RAM
areas but also other limits. Restore them on resume. On top of that,
some fixups are needed to work around BIOS bugs, in particular when
the BIOS omits running the same initialization sequence on resume
that it does after boot. In that case we have to carry initialization
over suspend.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
Thankfully this only affects systems with one specific south bridge
and is most probably harmless unless the hwmon module is heavily
cycled.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit 281dfd0 removed __devexit from the exit function but left __exit_p in
place. This results in the following warning message if the module is built into
the kernel.
twl4030-madc-hwmon.c:123:12: warning: ‘twl4030_madc_hwmon_remove’ defined
but not used [-Wunused-function]
Fix by removing __exit_p as well.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
|
|
Pull ARM SoC driver specific changes from Olof Johansson:
"A collection of mostly SoC-specific driver updates:
- a handful of pincontrol and setup changes
- new drivers for hwmon and reset controller for vexpress
- timing support updates for OMAP (gpmc and other interfaces)
- plus a collection of smaller cleanups"
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: ux500: fix pin warning
ARM: OMAP2+: tusb6010: generic timing calculation
ARM: OMAP2+: smc91x: generic timing calculation
ARM: OMAP2+: onenand: generic timing calculation
ARM: OMAP2+: gpmc: generic timing calculation
ARM: OMAP2+: gpmc: handle additional timings
ARM: OMAP2+: nand: remove redundant rounding
gpio: samsung: use pr_* instead of printk
ARM: ux500: fixup magnetometer pins
ARM: ux500: add STM pin configuration
ARM: ux500: 8500: add pinctrl support for uart1 and uart2
ARM: ux500: cosmetic fixups for uart0
gpio: samsung: Fix input mode setting function for GPIO int
ARM: SAMSUNG: Insert bitmap_gpio_int member in samsung_gpio_chip
ARM: ux500: 8500: define SDI sleep states
ARM: vexpress: Reset driver
ARM: ux500: 8500: update SKE keypad pinctrl table
hwmon: Versatile Express hwmon driver
ARM: ux500: delete duplicate macro
ARM: ux500: 8500: add IDLE pin configuration for SPI
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the large driver core updates for 3.8-rc1.
The biggest thing here is the various __dev* marking removals. This
is going to be a pain for the merge with different subsystem trees, I
know, but all of the patches included here have been ACKed by their
various subsystem maintainers, as they wanted them to go through here.
If this is too much of a pain, I can pull all of them out of this tree
and just send you one with the other fixes/updates and then, after
3.8-rc1 is out, do the rest of the removals to ensure we catch them
all, it's up to you. The merges should all be trivial, and Stephen
has been doing them all in linux-next for a few weeks now quite
easily.
Other than the __dev* marking removals, there's nothing major here,
some firmware loading updates and other minor things in the driver
core.
All of these have (much to Stephen's annoyance), been in linux-next
for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up trivial conflicts in drivers/gpio/gpio-{em,stmpe}.c due to gpio
update.
* tag 'driver-core-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (93 commits)
modpost.c: Stop checking __dev* section mismatches
init.h: Remove __dev* sections from the kernel
acpi: remove use of __devinit
PCI: Remove __dev* markings
PCI: Always build setup-bus when PCI is enabled
PCI: Move pci_uevent into pci-driver.c
PCI: Remove CONFIG_HOTPLUG ifdefs
unicore32/PCI: Remove CONFIG_HOTPLUG ifdefs
sh/PCI: Remove CONFIG_HOTPLUG ifdefs
powerpc/PCI: Remove CONFIG_HOTPLUG ifdefs
mips/PCI: Remove CONFIG_HOTPLUG ifdefs
microblaze/PCI: Remove CONFIG_HOTPLUG ifdefs
dma: remove use of __devinit
dma: remove use of __devexit_p
firewire: remove use of __devinitdata
firewire: remove use of __devinit
leds: remove use of __devexit
leds: remove use of __devinit
leds: remove use of __devexit_p
mmc: remove use of __devexit
...
|
|
Set chan_mux[DA9055_ADC_ADCIN3] = DA9055_ADC_MUX_ADCIN3.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This is the HWMON patch for DA9055 PMIC and has got dependency on the
DA9055 MFD core.
This patch monitors the DA9055 PMIC's ADC channels vddout, junction temperature
and auxiliary channels.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Guenter Roeck: Dropped __devinit, __devexit, __devexit_p]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Since N4xx, N5xx, D4xx, and D5xx are now reliably detected using the model ID
and the stepping/mask, drop the respective entries from tjmax_table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Make the code easier to extend and easier to adjust by using a model table
listing CPU models, stepping/mask, and associated TjMax.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
So far, we use the NM10 Express Chipset PCI chip ID to detect TjMax for
Atom CPUs with model 0x1c. As it turns out, we can use the CPU stepping
(x86_mask) for the same purpose; stepping is 10 for all model 0x1c CPUs
with TjMax of 100 degrees C. This was verified by checking the output of
/proc/cpuinfo for the respective CPUs (D4xx, D5xx, N4xx, N5xx).
Other CPUs currently covered by the same code (Exx, Z6xx, Z2460) are not
supported by the NM10 Express Chipset. Most of those CPUs have TjMax of 90
degrees C, except for E6xxT models which have a TjMax of 110 degrees C.
E6xxT CPUs can however not be detected by software.
Calculate TjMax for Atom CPUs as follows. Note that the listed values are not
correct in some cases (230, 330). tjmax_table is used for those to override
the default values.
ID Stepping TjMax Models
0x1c 10 100 D4xx, N4xx, D5xx, N5xx
0x1c not 10 90 Z5xx, N2xx, 230, 330, others
0x26 - 90 Atom Tunnel Creek (Exx),
Lincroft (Z6xx)
0x27 - 90 Atom Medfield (Z2460)
0x36 - 100 Atom Cedar Trail (N2xxx, D2xxx)
Also drop the module dependency on PCI.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The ADS7830 device is almost the same as the ADS7828,
except that it does 8-bit sampling, instead of 12-bit.
This patch extends the ads7828 driver to support this chip.
Signed-off-by: Guillaume Roguez <guillaume.roguez@savoirfairelinux.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
As there is no reliable way to identify the chip, it is preferable to
remove the detect callback, to avoid misdetection.
Module parameters are not worth it here, so let's get rid of them and
add an ads7828_platform_data structure instead.
Clean the code by removing unused macros, fixing coding style issues,
avoiding function prototypes and using convenient macros such as
module_i2c_driver().
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add family 16h PCI ID to AMD's power driver to allow it report
power consumption on these processors.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devinitdata is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Juerg Haefliger <juergh@gmail.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jim Cromie <jim.cromie@gmail.com>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Roger Lucas <vt8231@hiddenengine.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Needed for the omap timer changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
These got broken by recent patches fixing checkpatch warnings in these
drivers. The trick is that the patches themselves looked good, but the
source files after applying them do not. That's why I am not a big fan
of using tabs inside comments.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
Don't assume bank 0 is selected at device probe time. This may not be
the case. Force bank selection at first register access to guarantee
that we read the right registers upon driver loading.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
|
|
The following fixes build errors on sparc. Without any DT support,
of_match_ptr is NULL and the below is a no-op. However, if just
CONFIG_OF is defined then so is of_match_ptr.
All useful parts of the gpio-fan DT support rely on CONFIG_OF_GPIO
anyway, so of_match_table should too.
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Signed-off-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.linaro.org/people/pawelmoll/linux into next/drivers
Versatile Express changes from Pawel Moll <pawel.moll@arm.com>:
* 'vexpress-drivers' of git://git.linaro.org/people/pawelmoll/linux:
ARM: vexpress: Reset driver
hwmon: Versatile Express hwmon driver
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
hwmon framework driver for Versatile Express sensors, providing
information about board level voltage (only when regulator driver
is not configured), currents, temperature and power/energy usage.
Labels for the values can be defined as DT properties.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
|
|
TjMax for the CE4100 series of Atom CPUs was previously reported to be
110 degrees C.
cpuinfo logs on the web show existing CPU types CE4110, CE4150, and CE4170,
reported as "model name : Intel(R) Atom(TM) CPU CE41{1|5|7}0 @ 1.{2|6}0GHz"
with model 28 (0x1c) and stepping 10 (0x0a). Add the three known variants
to the tjmax table.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
cc: stable@vger.kernel.org
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Guenter Roeck <linux@roeck-us.net>
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux
Pull ACPI & Thermal updates from Len Brown:
"The generic Linux thermal layer is gaining some new capabilities
(generic cooling via cpufreq) and some new customers (ARM).
Also, an ACPI EC bug fix plus a regression fix."
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux: (30 commits)
tools/power/acpi/acpidump: remove duplicated include from acpidump.c
ACPI idle, CPU hotplug: Fix NULL pointer dereference during hotplug
cpuidle / ACPI: fix potential NULL pointer dereference
ACPI: EC: Add a quirk for CLEVO M720T/M730T laptop
ACPI: EC: Make the GPE storm threshold a module parameter
thermal: Exynos: Fix NULL pointer dereference in exynos_unregister_thermal()
Thermal: Fix bug on cpu_cooling, cooling device's id conflict problem.
thermal: exynos: Use devm_* functions
ARM: exynos: add thermal sensor driver platform data support
thermal: exynos: register the tmu sensor with the kernel thermal layer
thermal: exynos5: add exynos5250 thermal sensor driver support
hwmon: exynos4: move thermal sensor driver to driver/thermal directory
thermal: add generic cpufreq cooling implementation
Fix a build error.
thermal: Fix potential NULL pointer accesses
thermal: add Renesas R-Car thermal sensor support
thermal: fix potential out-of-bounds memory access
Thermal: Introduce locking for cdev.thermal_instances list.
Thermal: Unify the code for both active and passive cooling
Thermal: Introduce simple arbitrator for setting device cooling state
...
|
|
These drivers use no sleep or delay functions so they don't need to
include <linux/delay.h>.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Rudolf Marek <r.marek@assembler.cz>
|
|
These drivers use IS_ERR so they should include <linux/err.h>.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Henrik Rydberg <rydberg@euromail.se>
|
|
Many hwmon drivers use jiffies but omit the inclusion of the header
file. Fix that, and also fix one driver which was including the header
file but didn't need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
|
|
My name was change after migration.
Signed-off-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
|
