| Age | Commit message (Collapse) | Author |
|---|
|
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
- new drivers: Kontron PLD, Wondermedia VT
- mv64xxx driver gained sun4i support and a bigger cleanup
- duplicate driver 'intel-mid' removed
- added generic device tree binding for sda holding time (and
designware driver already uses it)
- we tried to allow driver probing with only device tree and no i2c
ids, but I had to revert it because of side effects. Needs some
rethinking.
- driver bugfixes, cleanups...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c-designware: use div_u64 to fix link
i2c: Kontron PLD i2c bus driver
i2c: iop3xxx: fix build failure after waitqueue changes
i2c-designware: make SDA hold time configurable
i2c: mv64xxx: Set bus frequency to 100kHz if clock-frequency is not provided
i2c: imx: allow autoloading on dt ids
i2c: mv64xxx: Fix transfer error code
i2c: i801: SMBus patch for Intel Coleto Creek DeviceIDs
i2c: omap: correct usage of the interrupt enable register
i2c-pxa: prepare clock before use
Revert "i2c: core: make it possible to match a pure device tree driver"
i2c: nomadik: allocate adapter number dynamically
i2c: nomadik: support elder Nomadiks
i2c: mv64xxx: Add Allwinner sun4i compatible
i2c: mv64xxx: make the registers offset configurable
i2c: mv64xxx: Add macros to access parts of registers
i2c: vt8500: Add support for I2C bus on Wondermedia SoCs
i2c: designware: fix race between subsequent xfers
i2c: bfin-twi: Read and write the FIFO in loop
i2c: core: make it possible to match a pure device tree driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc changes for the 3.11 merge window. In addition to
the usual bug fixes and small updates, the main highlights are:
- Support for transparent huge pages by Aneesh Kumar for 64-bit
server processors. This allows the use of 16M pages as transparent
huge pages on kernels compiled with a 64K base page size.
- Base VFIO support for KVM on power by Alexey Kardashevskiy
- Wiring up of our nvram to the pstore infrastructure, including
putting compressed oopses in there by Aruna Balakrishnaiah
- Move, rework and improve our "EEH" (basically PCI error handling
and recovery) infrastructure. It is no longer specific to pseries
but is now usable by the new "powernv" platform as well (no
hypervisor) by Gavin Shan.
- I fixed some bugs in our math-emu instruction decoding and made it
usable to emulate some optional FP instructions on processors with
hard FP that lack them (such as fsqrt on Freescale embedded
processors).
- Support for Power8 "Event Based Branch" facility by Michael
Ellerman. This facility allows what is basically "userspace
interrupts" for performance monitor events.
- A bunch of Transactional Memory vs. Signals bug fixes and HW
breakpoint/watchpoint fixes by Michael Neuling.
And more ... I appologize in advance if I've failed to highlight
something that somebody deemed worth it."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
pstore: Add hsize argument in write_buf call of pstore_ftrace_call
powerpc/fsl: add MPIC timer wakeup support
powerpc/mpic: create mpic subsystem object
powerpc/mpic: add global timer support
powerpc/mpic: add irq_set_wake support
powerpc/85xx: enable coreint for all the 64bit boards
powerpc/8xx: Erroneous double irq_eoi() on CPM IRQ in MPC8xx
powerpc/fsl: Enable CONFIG_E1000E in mpc85xx_smp_defconfig
powerpc/mpic: Add get_version API both for internal and external use
powerpc: Handle both new style and old style reserve maps
powerpc/hw_brk: Fix off by one error when validating DAWR region end
powerpc/pseries: Support compression of oops text via pstore
powerpc/pseries: Re-organise the oops compression code
pstore: Pass header size in the pstore write callback
powerpc/powernv: Fix iommu initialization again
powerpc/pseries: Inform the hypervisor we are using EBB regs
powerpc/perf: Add power8 EBB support
powerpc/perf: Core EBB support for 64-bit book3s
powerpc/perf: Drop MMCRA from thread_struct
powerpc/perf: Don't enable if we have zero events
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"PCI device hotplug
- Add pci_alloc_dev() interface (Gu Zheng)
- Add pci_bus_get()/put() for reference counting (Jiang Liu)
- Fix SR-IOV reference count issues (Jiang Liu)
- Remove unused acpi_pci_roots list (Jiang Liu)
MSI
- Conserve interrupt resources on x86 (Alexander Gordeev)
AER
- Force fatal severity when component has been reset (Betty Dall)
- Reset link below Root Port as well as Downstream Port (Betty Dall)
- Fix "Firmware first" flag setting (Bjorn Helgaas)
- Don't parse HEST for non-PCIe devices (Bjorn Helgaas)
ASPM
- Warn when we can't disable ASPM as driver requests (Bjorn Helgaas)
Miscellaneous
- Add CircuitCo PCI IDs (Darren Hart)
- Add AMD CZ SATA and SMBus PCI IDs (Shane Huang)
- Work around Ivytown NTB BAR size issue (Jon Mason)
- Detect invalid initial BAR values (Kevin Hao)
- Add pcibios_release_device() (Sebastian Ott)
- Fix powerpc & sparc PCI_UNKNOWN power state usage (Bjorn Helgaas)"
* tag 'pci-v3.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (51 commits)
MAINTAINERS: Add ACPI folks for ACPI-related things under drivers/pci
PCI: Add CircuitCo vendor ID and subsystem ID
PCI: Use pdev->pm_cap instead of pci_find_capability(..,PCI_CAP_ID_PM)
PCI: Return early on allocation failures to unindent mainline code
PCI: Simplify IOV implementation and fix reference count races
PCI: Drop redundant setting of bus->is_added in virtfn_add_bus()
unicore32/PCI: Remove redundant call of pci_bus_add_devices()
m68k/PCI: Remove redundant call of pci_bus_add_devices()
PCI / ACPI / PM: Use correct power state strings in messages
PCI: Fix comment typo for pcie_pme_remove()
PCI: Rename pci_release_bus_bridge_dev() to pci_release_host_bridge_dev()
PCI: Fix refcount issue in pci_create_root_bus() error recovery path
ia64/PCI: Clean up pci_scan_root_bus() usage
PCI/AER: Reset link for devices below Root Port or Downstream Port
ACPI / APEI: Force fatal AER severity when component has been reset
PCI/AER: Remove "extern" from function declarations
PCI/AER: Move AER severity defines to aer.h
PCI/AER: Set dev->__aer_firmware_first only for matching devices
PCI/AER: Factor out HEST device type matching
PCI/AER: Don't parse HEST table for non-PCIe devices
...
|
|
This fixes the following link error:
drivers/built-in.o: In function `dw_i2c_probe':
of_iommu.c:(.text+0x18c8f0): undefined reference to `__aeabi_uldivmod'
make: *** [vmlinux] Error 1
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"These changes are all to SoC-specific code, a total of 33 branches on
17 platforms were pulled into this. Like last time, Renesas sh-mobile
is now the platform with the most changes, followed by OMAP and
EXYNOS.
Two new platforms, TI Keystone and Rockchips RK3xxx are added in this
branch, both containing almost no platform specific code at all, since
they are using generic subsystem interfaces for clocks, pinctrl,
interrupts etc. The device drivers are getting merged through the
respective subsystem maintainer trees.
One more SoC (u300) is now multiplatform capable and several others
(shmobile, exynos, msm, integrator, kirkwood, clps711x) are moving
towards that goal with this series but need more work.
Also noteworthy is the work on PCI here, which is traditionally part
of the SoC specific code. With the changes done by Thomas Petazzoni,
we can now more easily have PCI host controller drivers as loadable
modules and keep them separate from the platform code in
drivers/pci/host. This has already led to the discovery that three
platforms (exynos, spear and imx) are actually using an identical PCIe
host controller and will be able to share a driver once support for
spear and imx is added."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (480 commits)
ARM: integrator: let pciv3 use mem/premem from device tree
ARM: integrator: set local side PCI addresses right
ARM: dts: Add pcie controller node for exynos5440-ssdk5440
ARM: dts: Add pcie controller node for Samsung EXYNOS5440 SoC
ARM: EXYNOS: Enable PCIe support for Exynos5440
pci: Add PCIe driver for Samsung Exynos
ARM: OMAP5: voltagedomain data: remove temporary OMAP4 voltage data
ARM: keystone: Move CPU bringup code to dedicated asm file
ARM: multiplatform: always pick one CPU type
ARM: imx: select syscon for IMX6SL
ARM: keystone: select ARM_ERRATA_798181 only for SMP
ARM: imx: Synertronixx scb9328 needs to select SOC_IMX1
ARM: OMAP2+: AM43x: resolve SMP related build error
dmaengine: edma: enable build for AM33XX
ARM: edma: Add EDMA crossbar event mux support
ARM: edma: Add DT and runtime PM support to the private EDMA API
dmaengine: edma: Add TI EDMA device tree binding
arm: add basic support for Rockchip RK3066a boards
arm: add debug uarts for rockchip rk29xx and rk3xxx series
arm: Add basic clocks for Rockchip rk3066a SoCs
...
|
|
Add i2c support for the on-board PLD found on some Kontron embedded
modules.
Originally-From: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
There has long been a syntax problem in iop3xx_i2c_wait_event() which
has been somehow hidden by the macros in <linux/wait.h>. After some
recent cleanup/rework of the wait_event_* helpers, the bug has come
out from hiding and now results in build failure:
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c: In function 'iop3xx_i2c_wait_event':
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:143: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:157: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:213: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:291: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement]
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:551: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:565: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:764: error: expected ')' before ';' token
/work/kernel/next/drivers/i2c/busses/i2c-iop3xx.c:176:778: error: expected ')' b
Fix by removing stray ';'
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch makes the SDA hold time configurable through device tree.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com> for arch/arc bits
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
In case of collision on i2c bus the controller which lost bus mastership
stays as a slave for all subsequent transfers. This results in the i2c
controller never writing to the bus for future transactions, resulting
in i2c transfer timeouts.
This fix checks for a collision on last I2C transaction and sets the
I2COM_MASTER bit for the new transaction.
Signed-off-by: Sachin Surendran <sachin.surendran@alliedtelesis.co.nz>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This commit adds checking whether clock-frequency property acquisition
has succeeded. If not, the frequency is set to 100kHz by default.
The Device Tree binding documentation is updated accordingly.
Based on the intials patches from Zbigniew Bodek
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Zbigniew Bodek <zbb@semihalf.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Allow udev to autoload the module when booting with device-tree
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The driver returns -ENODEV as error code if it did not get an ACK
from the device. Per Documentation/i2c/fault-codes, it should
return -ENXIO.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds the i801 SMBus Controller DeviceIDs for the Intel Coleto Creek PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/soc
From Linus Walleij:
Device Tree and Multiplatform support for U300:
- Add devicetree support to timer, pinctrl (probe), I2C block,
watchdog, DMA controller and clocks.
- Piecewise add a device tree containing all peripherals.
- Delete the ATAG boot path.
- Delete redundant platform data and board files.
- Convert to multiplatform.
* tag 'u300-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (40 commits)
ARM: u300: switch to using syscon regmap for board
ARM: u300: Update MMC configs for u300 defconfig
spi: pl022: use DMA by default when probing from DT
pinctrl: get rid of all platform data for coh901
ARM: u300: convert MMC/SD clock to device tree
ARM: u300: move the gated system controller clocks to DT
i2c: stu300: do not request a specific clock name
clk: move the U300 fixed and fixed-factor to DT
ARM: u300: remove register definition file
ARM: u300: add syscon node
ARM: u300 use module_spi_driver to register driver
ARM: u300: delete remnant machine headers
ARM: u300: convert to multiplatform
ARM: u300: localize <mach/u300-regs.h>
ARM: u300: delete <mach/irqs.h>
ARM: u300: delete <mach/hardware.h>
ARM: u300: push down syscon registers
ARM: u300: remove deps from debug macro
ARM: u300: move debugmacro to debug includes
ARM: u300: delete all static board data
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
|
|
We've been lucky not to have any interrupts fire during the suspend
path, otherwise we would have unpredictable behaviour in the kernel.
Based on the logic of the kernel code interrupts from i2c should be
prohibited during suspend. Kernel writes 0 to the I2C_IE register in
the omap_i2c_runtime_suspend() function. In the other side kernel
writes saved interrupt flags to the I2C_IE register in
omap_i2c_runtime_resume() function. I.e. interrupts should be disabled
during suspend.
This works for chips with version1 registers scheme. Interrupts are
disabled during suspend. For chips with version2 scheme registers
writting 0 to the I2C_IE register does nothing (because now the
I2C_IRQENABLE_SET register is located at this address). This register
is used to enable interrupts. For disabling interrupts
I2C_IRQENABLE_CLR register should be used.
Because the registers I2C_IRQENABLE_SET and I2C_IE have the same
addresses, the interrupt enabling procedure is unchanged.
I've checked that interrupts in the i2c controller are still enabled
after writting 0 to the I2C_IRQENABLE_SET register. With this patch
interrupts are disabled in the omap_i2c_runtime_suspend() function.
Patch is based on:
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
tag: v3.10-rc2
Verified on OMAP4430.
Signed-off-by: Oleksandr Dmytryshyn <oleksandr.dmytryshyn@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
On OLPC XO-1.75 (MMP2), a WARN_ON() was occurring during boot
since the clock being enabled by i2c-pxa had not been prepared.
Use clk_prepare_enable() to ensure that the prepare operation
has taken place, and use clk_disable_unprepare() in the matching
shutdown paths.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We have used the default clock associated with the block
for a long time, only heuristics in the clock system has
made this work anyway. This needs to be done away with as
we start probing this driver and its clocks exclusively
from the device tree.
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This utilize the new pinctrl core PM helpers to transition
the driver to "sleep" and "idle" states, cutting away some
boilerplate code.
Cc: Hebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Nomadik I2C was using a local atomic counter to number
the I2C adapters. This does not work on configurations where
you also add, say a GPIO bit-banged adapter to the system.
They will start to conflict about being adapter 0.
There is no reason to use the numbered adapter function, and
the semantic effect on systems with only Nomadik I2C blocks
will be none - instead of increasing the number atomically
in the driver itself, it is done in the I2C core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Nomadik I2C block was introduced with the Nomadik STn8815
SoC (the STn8810 incidentally is identical to the one named
i2c-stu300.c). However as developments have only been tested
on the DB8500 family, it was not properly working with the
STn8815 anymore.
Rectify this by adding some vendor variant data in the same
manner as other PrimeCells, and switch code path depending
on version.
Tested on the S8815 Nomadik dongle.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add the compatible string for the Allwinner A10 i2c controller and the
associated register layout.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The Allwinner i2c controller uses the same logic as the Marvell one, but
with slightly different register offsets.
Introduce a structure that will be passed by either the pdata or
associated to the compatible strings, and that holds the various
registers that might be needed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
These macros make it more comprehensive to access to useful masked and
shifted area of the various registers used.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This patch adds support for the I2C bus controllers found on Wondermedia
8xxx-series SoCs. Only master-mode is supported.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
[wsa: fixed one macro to shift 8 instead of 16]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The designware block is not always properly disabled in the case of
transfer errors. Interrupts from aborted transfers might be handled
after the data structures for the following transfer are initialised but
before the hardware is set up. This can corrupt the data structures to
the point that the system is stuck in an infinite interrupt loop (where
FIFOs are never emptied because dev->msg_read_idx == dev->msgs_num).
This patch cleanly disables the designware-i2c hardware at the end of
every transfer, be it successful or not.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
[wsa: extended the comment]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
TWI transfer interrupts may be lost when system is heavily handling other
interrupts, while current transfer handler depends on each accurate interrupt
and misses some data in this case. Because there are 2 2-byte FIFOs in blackfin
TWI controller, the occurrence of the data loss can be reduced by reading till
the RX FIFO is empty and writing till the TX FIFO is full.
Reported-by: Bob Maris <mail@maris-ee.eu>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If a process receives signal while it is waiting for I2C transfer to
complete, an error is returned to the caller and the transfer is aborted.
This can cause the driver to fail subsequent transfers. Also according to
commit d295a86eab2 (i2c: mv64xxx: work around signals causing I2C
transactions to be aborted) I2C drivers aren't supposed to abort
transactions on signals.
To prevent this switch to use wait_for_completion_timeout() instead of
wait_for_completion_interruptible_timeout() in the designware I2C driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for handling pinctrl.
So remove devm_pinctrl_get_select_default() from the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
CAVIUM_OCTEON_SOC most place we used to use CPU_CAVIUM_OCTEON. This
allows us to CPU_CAVIUM_OCTEON in places where we have no OCTEON SOC.
Remove CAVIUM_OCTEON_SIMULATOR as it doesn't really do anything, we can
get the same configuration with CAVIUM_OCTEON_SOC.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-ide@vger.kernel.org
Cc: linux-edac@vger.kernel.org
Cc: linux-i2c@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: spi-devel-general@lists.sourceforge.net
Cc: devel@driverdev.osuosl.org
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patchwork: https://patchwork.linux-mips.org/patch/5295/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Asking for a multi-part message to be handled by this driver is racy; it
has been observed that the following sequence is possible with this
driver:
- send start
- send address + write
- send data
- send (repeated) start
- send address + write
- send (repeated) start
- send address + read
- unrecoverable bus hang (except by system reset)
The problem is that the interrupt handling sees the next event after the
first repeated start is sent - the IFLG bit is set in the register even
though INTEN is disabled.
Let's fix this by moving all of the message processing into interrupt
context, rather than having it partly in IRQ and partly in process
context. This allows us to move immediately to the next message in the
interrupt handler and get on with the transfer, rather than incuring a
couple of scheduling switches to get the next message.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Move mv64xxx_i2c_prepare_for_io() higher up in the driver to avoid a
future forward declaration for this function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
As this driver does not advertise protocol mangling support
(I2C_FUNC_PROTOCOL_MANGLING is not set), having code to act on
I2C_M_NOSTART is illogical, and in any case isn't supportable on
anything but the first message - which makes no sense. Remove
the I2C_M_NOSTART code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Propagate the error code from request_irq() rather than ignoring it
entirely.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
As we're changing to using devm_* APIs to fix various problems
in this driver, lets also do devm_kzalloc() while we're here too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This driver forgets to use clk_put(). Rather than adding clk_put(),
lets instead use devm_clk_get() to obtain this clock so that it's
automatically handled on cleanup.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Eliminate reg_base_p and reg_size, mv64xxx_i2c_unmap_regs() and an
unchecked ioremap() return from this driver by using the devm_*
API for requesting and ioremapping resources.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
mv64xxx_i2c_map_regs() already returns an error code, so lets
propagate that to mv64xxx_i2c_probe()'s caller.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Moorestown support is removed from kernel and Medfield is supported by
i2c-designware-pci. But i2c-intel-mid is still in upstream and community
resources are wasted to maintain it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
To add AMD CZ SMBus controller device ID.
[bhelgaas: drop pci_ids.h update]
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
|
|
This adds device tree support for the ST DDC I2C driver known
as "stu300" in the kernel tree.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c bugfixes from Wolfram Sang:
"These should have been in rc2 but I missed it due to working on devm
longer than expected.
There is one ID addition, since we are touching the driver anyhow.
And the feature bit documentation is one outcome of a debug session
and will make it easier for users to work around problems. The rest
is typical driver bugfixes."
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: suppress lockdep warning on delete_device
i2c: mv64xxx: work around signals causing I2C transactions to be aborted
i2c: i801: Document feature bits in modinfo
i2c: designware: add Intel BayTrail ACPI ID
i2c: designware: always clear interrupts before enabling them
i2c: designware: fix RX FIFO overrun
|
|
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Barry Song <Baohua.Song@csr.com>
|
|
Do not use interruptible waits in an I2C driver; if a process uses
signals (eg, Xorg uses SIGALRM and SIGPIPE) then these signals can
cause the I2C driver to abort a transaction in progress by another
driver, which can cause that driver to fail. I2C drivers are not
expected to abort transactions on signals.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Duplicate the feature bits documentation in modinfo, as not every user
will read the driver's source code or documentation file.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
