Age | Commit message (Collapse) | Author |
|
This patch optimizes pio buffer allocation in the kernel.
For qib, kernel pio buffers are used for sending acks. The code to
allocate the buffer would always start at 0 until it found a buffer.
This means that an average of 64 comparisions were done on each
allocate, since the busy bit won't be cleared until the bits are
refreshed when buffers are exhausted.
This patch adds two new fields in the devdata struct, last_pio and
min_kernel_pio. last_pio is the last buffer that was allocated.
min_kernel_pio is the lowest potential available buffer.
min_kernel_pio is modifed as contexts are allocated and deallocted.
Reviewed-by: Ramkrishna Vepa <ramkrishna.vepa@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Add a prefetch call when a packet has been stored. The nature of the
prefetch is correctly determined by the alternatives mechanism.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"A few fixes for regressions introduced in 3.4-rc1:
- fix memory leak in mlx4
- fix two problems with new MAD response generation code"
* tag 'ib-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix memory leaks in ib_link_query_port()
IB/mad: Don't send response for failed MADs
IB/mad: Set 'D' bit in response for unhandled MADs
|
|
|
|
If the call to mlx4_MAD_IFC() fails in ib_link_query_port() we will
currently do 'return err;' which will leak 'in_mad' and 'out_mad'. We
should instead do 'goto out;' where we'll properly free the memory we
previously allocated.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit 0b307043049f ("IB/mad: Return error response for unsupported
MADs") does not failed MADs (eg those that return
IB_MAD_RESULT_FAILURE) properly -- these MADs should be silently
discarded. (We should not force the lower-layer drivers to return
SUCCESS | CONSUMED in this case, since the MAD is NOT successful).
Unsupported MADs are not failures -- they return SUCCESS, but with an
"unsupported error" status value inside the response MAD.
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit 0b307043049f ("IB/mad: Return error response for unsupported
MADs") does not handle directed-route MADs properly -- it fails to set
the 'D' bit in the response MAD status field. This is a problem for
SmInfo MADs when the receiver does not have an SM running.
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fix from Roland Dreier:
"Add a fix for a bug hit by Alexey Shvetsov in ib_srtp that hits on
non-mlx4 hardware."
* tag 'srpt-srq-type' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/srpt: Set srq_type to IB_SRQT_BASIC
|
|
Since commit 96104eda0169 ("RDMA/core: Add SRQ type field"), kernel
users of SRQs need to specify srq_type = IB_SRQT_BASIC in struct
ib_srq_init_attr, or else most low-level drivers will fail in
when srpt_add_one() calls ib_create_srq() and gets -ENOSYS.
(mlx4_ib works OK nearly all of the time, because it just needs
srq_type != IB_SRQT_XRC. And apparently nearly everyone using
ib_srpt is using mlx4 hardware)
Reported-by: Alexey Shvetsov <alexxy@gentoo.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit e9319b0cb00d ("IB/core: Fix SDR rates in sysfs") changed our
sysfs rate attribute to return EINVAL to userspace if the underlying
device driver returns an invalid rate. Apparently some drivers do this
when the link is down and some userspace pukes if it gets an error when
reading this attribute, so avoid a regression by not return an error to
match the old code.
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When the IB port is down, the active_speed value returned by the
MAD_IFC command is seven (7) which isn't among the defined IB speeds
in enum ib_port_speed, and this invalid speed value is passed up to
higher layers or applications who do port query.
Fix that by setting the speed to be SDR -- the lowest possible -- when
the port is down.
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes for the 3.4 merge window from Roland Dreier:
"Nothing big really stands out; by patch count lots of fixes to the
mlx4 driver plus some cleanups and fixes to the core and other
drivers."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (28 commits)
mlx4_core: Scale size of MTT table with system RAM
mlx4_core: Allow dynamic MTU configuration for IB ports
IB/mlx4: Fix info returned when querying IBoE ports
IB/mlx4: Fix possible missed completion event
mlx4_core: Report thermal error events
mlx4_core: Fix one more static exported function
IB: Change CQE "csum_ok" field to a bit flag
RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
RDMA/cxgb3: Don't pass irq flags to flush_qp()
mlx4_core: Get rid of redundant ext_port_cap flags
RDMA/ucma: Fix AB-BA deadlock
IB/ehca: Fix ilog2() compile failure
IB: Use central enum for speed instead of hard-coded values
IB/iser: Post initial receive buffers before sending the final login request
IB/iser: Free IB connection resources in the proper place
IB/srp: Consolidate repetitive sysfs code
IB/srp: Use pr_fmt() and pr_err()/pr_warn()
IB/core: Fix SDR rates in sysfs
mlx4: Enforce device max FMR maps in FMR alloc
IB/mlx4: Set bad_wr for invalid send opcode
...
|
|
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
|
|
Acked-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
|
|
'srp' and 'srpt' into for-next
|
|
This patch addresses a bug in srpt_handle_cmd() failure handling where
send_ioctx->kref is being leaked with the local extra reference after init,
causing the expected kref_put() in srpt_handle_send_comp() to not be the final
call to invoke srpt_put_send_ioctx_kref() -> transport_generic_free_cmd() and
perform se_cmd descriptor memory release.
It also fixes a SCF_SCSI_RESERVATION_CONFLICT handling bug where this code
is incorrectly falling through to transport_handle_cdb_direct() after
invoking srpt_queue_status() to send SAM_STAT_RESERVATION_CONFLICT status.
Note this patch is for >= v3.3 mainline code, and current lio-core.git
code has already been converted to target_submit_cmd() + se_cmd->cmd_kref usage,
and internal ioctx->kref usage has been removed. I'm including this patch
now into target-pending/for-next with a CC' for v3.3 stable.
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Conflicts:
drivers/infiniband/hw/mlx4/main.c
drivers/net/ethernet/mellanox/mlx4/main.c
include/linux/mlx4/device.h
|
|
To issue a port query, use the QUERY_(Ethernet)_PORT command instead
of the MAD_IFC command, since MAD_IFC attempts to query the firmware
IB SMA, which is irrelevant for IBoE ports.
This allows us to handle both 10Gb/s and 40Gb/s rates (e.g in sysfs),
using QDR speed (10Gb/s) and width of 1X or 4X.
Signed-off-by: Dotan Barak <dotanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
If an erroneous CQE is polled in the first iteration (i.e. npolled ==
0), we don't update the consumer index and hence the hardware could
get a wrong notion of how many CQEs software polled. Fix this by
unconditionally updating the doorbell record. We could change the
check to be something like
if (npolled || err != -EAGAIN)
...
but it does not seem worth the effort since a posted write to memory
should not cost too much.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
This patch drops the following unused legacy API callers from target_core_fabric.h:
*) TFO->fall_back_to_erl0()
*) TFO->stop_session()
*) TFO->sess_logged_in()
*) TFO->is_state_remove()
This patch also removes the stub usage in loopback, tcm_fc, iscsi_target,
and ib_srpt fabric modules.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Use a bit in wc_flags rather then a whole integer to hold the
"checksum OK" flag. By itself, this change doesn't reduce the size of
struct ib_wc on 64bit machines -- it stays on 56 bytes because of
padding. However, it will allow to add more fields in the future
without enlarging the struct. Also, it will let us have a unified
approach with future libibverbs checksum offload reporting, because a
bit flag doesn't break the library ABI.
This patch was suggested during conversation with Liran Liss
<liranl@mellanox.com>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When destroying a listening cmid, the iwcm first marks the state of
the cmid as DESTROYING, then releases the lock and calls into the
iWARP provider to destroy the endpoint. Since the cmid is not locked,
its possible for the iWARP provider to pass a connection request event
to the iwcm, which will be silently dropped by the iwcm. This causes
the iWARP provider to never free up the resources from this connection
because the assumption is the iwcm will accept or reject this connection.
The solution is to reject these connection requests.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Since flush_qp() is always called with irqs disabled, all the locking
inside flush_qp() and __flush_qp() doesn't need irq save/restore.
Further, passing the flag variable from iwch_modify_qp() is just wrong
and causes a WARN_ON() in local_bh_enable().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
While doing the work for commit a6f7feae6d ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b7817 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).
This patch reverts commit 97285b7817 and removes the check for
extended caps from the mlx4_ib driver port query flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
When we destroy a cm_id, we must purge associated events from the
event queue. If the cm_id is for a listen request, we also purge
corresponding pending connect requests. This requires destroying
the cm_id's associated with the connect requests by calling
rdma_destroy_id(). rdma_destroy_id() blocks until all outstanding
callbacks have completed.
The issue is that we hold file->mut while purging events from the
event queue. We also acquire file->mut in our event handler. Calling
rdma_destroy_id() while holding file->mut can lead to a deadlock,
since the event handler callback cannot acquire file->mut, which
prevents rdma_destroy_id() from completing.
Fix this by moving events to purge from the event queue to a temporary
list. We can then release file->mut and call rdma_destroy_id()
outside of holding any locks.
Bug report by Or Gerlitz <ogerlitz@mellanox.com>:
[ INFO: possible circular locking dependency detected ]
3.3.0-rc5-00008-g79f1e43-dirty #34 Tainted: G I
tgtd/9018 is trying to acquire lock:
(&id_priv->handler_mutex){+.+.+.}, at: [<ffffffffa0359a41>] rdma_destroy_id+0x33/0x1f0 [rdma_cm]
but task is already holding lock:
(&file->mut){+.+.+.}, at: [<ffffffffa02470fe>] ucma_free_ctx+0xb6/0x196 [rdma_ucm]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&file->mut){+.+.+.}:
[<ffffffff810682f3>] lock_acquire+0xf0/0x116
[<ffffffff8135f179>] mutex_lock_nested+0x64/0x2e6
[<ffffffffa0247636>] ucma_event_handler+0x148/0x1dc [rdma_ucm]
[<ffffffffa035a79a>] cma_ib_handler+0x1a7/0x1f7 [rdma_cm]
[<ffffffffa0333e88>] cm_process_work+0x32/0x119 [ib_cm]
[<ffffffffa03362ab>] cm_work_handler+0xfb8/0xfe5 [ib_cm]
[<ffffffff810423e2>] process_one_work+0x2bd/0x4a6
[<ffffffff810429e2>] worker_thread+0x1d6/0x350
[<ffffffff810462a6>] kthread+0x84/0x8c
[<ffffffff81369624>] kernel_thread_helper+0x4/0x10
-> #0 (&id_priv->handler_mutex){+.+.+.}:
[<ffffffff81067b86>] __lock_acquire+0x10d5/0x1752
[<ffffffff810682f3>] lock_acquire+0xf0/0x116
[<ffffffff8135f179>] mutex_lock_nested+0x64/0x2e6
[<ffffffffa0359a41>] rdma_destroy_id+0x33/0x1f0 [rdma_cm]
[<ffffffffa024715f>] ucma_free_ctx+0x117/0x196 [rdma_ucm]
[<ffffffffa0247255>] ucma_close+0x77/0xb4 [rdma_ucm]
[<ffffffff810df6ef>] fput+0x117/0x1cf
[<ffffffff810dc76e>] filp_close+0x6d/0x78
[<ffffffff8102b667>] put_files_struct+0xbd/0x17d
[<ffffffff8102b76d>] exit_files+0x46/0x4e
[<ffffffff8102d057>] do_exit+0x299/0x75d
[<ffffffff8102d599>] do_group_exit+0x7e/0xa9
[<ffffffff8103ae4b>] get_signal_to_deliver+0x536/0x555
[<ffffffff81001717>] do_signal+0x39/0x634
[<ffffffff81001d39>] do_notify_resume+0x27/0x69
[<ffffffff81361c03>] retint_signal+0x46/0x83
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&file->mut);
lock(&id_priv->handler_mutex);
lock(&file->mut);
lock(&id_priv->handler_mutex);
*** DEADLOCK ***
1 lock held by tgtd/9018:
#0: (&file->mut){+.+.+.}, at: [<ffffffffa02470fe>] ucma_free_ctx+0xb6/0x196 [rdma_ucm]
stack backtrace:
Pid: 9018, comm: tgtd Tainted: G I 3.3.0-rc5-00008-g79f1e43-dirty #34
Call Trace:
[<ffffffff81029e9c>] ? console_unlock+0x18e/0x207
[<ffffffff81066433>] print_circular_bug+0x28e/0x29f
[<ffffffff81067b86>] __lock_acquire+0x10d5/0x1752
[<ffffffff810682f3>] lock_acquire+0xf0/0x116
[<ffffffffa0359a41>] ? rdma_destroy_id+0x33/0x1f0 [rdma_cm]
[<ffffffff8135f179>] mutex_lock_nested+0x64/0x2e6
[<ffffffffa0359a41>] ? rdma_destroy_id+0x33/0x1f0 [rdma_cm]
[<ffffffff8106546d>] ? trace_hardirqs_on_caller+0x11e/0x155
[<ffffffff810654b1>] ? trace_hardirqs_on+0xd/0xf
[<ffffffffa0359a41>] rdma_destroy_id+0x33/0x1f0 [rdma_cm]
[<ffffffffa024715f>] ucma_free_ctx+0x117/0x196 [rdma_ucm]
[<ffffffffa0247255>] ucma_close+0x77/0xb4 [rdma_ucm]
[<ffffffff810df6ef>] fput+0x117/0x1cf
[<ffffffff810dc76e>] filp_close+0x6d/0x78
[<ffffffff8102b667>] put_files_struct+0xbd/0x17d
[<ffffffff8102b5cc>] ? put_files_struct+0x22/0x17d
[<ffffffff8102b76d>] exit_files+0x46/0x4e
[<ffffffff8102d057>] do_exit+0x299/0x75d
[<ffffffff8102d599>] do_group_exit+0x7e/0xa9
[<ffffffff8103ae4b>] get_signal_to_deliver+0x536/0x555
[<ffffffff810654b1>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff81001717>] do_signal+0x39/0x634
[<ffffffff8135e037>] ? printk+0x3c/0x45
[<ffffffff8106546d>] ? trace_hardirqs_on_caller+0x11e/0x155
[<ffffffff810654b1>] ? trace_hardirqs_on+0xd/0xf
[<ffffffff81361803>] ? _raw_spin_unlock_irq+0x2b/0x40
[<ffffffff81039011>] ? set_current_blocked+0x44/0x49
[<ffffffff81361bce>] ? retint_signal+0x11/0x83
[<ffffffff81001d39>] do_notify_resume+0x27/0x69
[<ffffffff8118a1fe>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff81361c03>] retint_signal+0x46/0x83
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
I'm getting compile failures building this driver, which I narrowed
down to the ilog2 call in ehca_get_max_hwpage_size...
ERROR: ".____ilog2_NaN" [drivers/infiniband/hw/ehca/ib_ehca.ko]
undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
The use of shca->hca_cap_mr_pgsize is confusing the compiler, and
resulting in the __builtin_constant_p in ilog2 going insane.
I tried making it take the u32 pgsize as an argument and the expansion
of shca->_pgsize in the caller, but that failed as well.
With this patch in place, the driver compiles on my GCC 4.6.2 here.
Suggested-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Kyle McMartin <kmcmarti@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The kernel IB stack uses one enumeration for IB speed, which wasn't
explicitly specified in the verbs header file. Add that enum, and use
it all over the code.
The IB speed/width notation is also used by iWARP and IBoE HW drivers,
which use the convention of rate = speed * width to advertise their
port link rate.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
An iser target may send iscsi NO-OP PDUs as soon as it marks the iSER
iSCSI session as fully operative. This means that there is window
where there are no posted receive buffers on the initiator side, so
it's possible for the iSER RC connection to break because of RNR NAK /
retry errors. To fix this, rely on the flags bits in the login
request to have FFP (0x3) in the lower nibble as a marker for the
final login request, and post an initial chunk of receive buffers
before sending that login request instead of after getting the login
response.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
We allocate the login dma buffers in iser_verbs.c as part of
alloc_ib_conn_resources(), however we are freeing them in
iser_initiator.c as part of iser_free_rx_descriptors(). This is
needlessly confusing. We have an alloc_rx_descriptors() and it
doesn't alloc something that the free_rx_descriptors() frees, and we
have an alloc_ib_conn_resources() that allocs something not freed by
free_ib_conn_resources(). Clean that up.
Signed-off-by: Doug Ledford <dledford@redhat.com>
[ Fix build error in iser_free_ib_conn_res(). - Or ]
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Remove sysfs attributes before removing a target instead of testing
the target state in every sysfs attribute callback method. Note: it is
safe to invoke a sysfs attribute removal method like
device_remove_file() twice on the same attribute.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Use pr_fmt() and pr_xxx() instead of more verbose printk() equivalents.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit 71eeba16 ("IB: Add new InfiniBand link speeds") introduced a bug
where eg the rate for IB 4X SDR links iss displayed as "8.5 Gb/sec"
instead of "10 Gb/sec" as it used to be. Fix that.
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Davem considers that the argument list of this interface is getting
out of control. This patch tries to address this issue following
his proposal:
struct netlink_dump_control c = { .dump = dump, .done = done, ... };
netlink_dump_start(..., &c);
Suggested by David S. Miller.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ConnectX devices have a limit on the number of mappings that can be
done on an FMR before having to call sync_tpt. The current
mlx4_ib driver reports the limit correctly in max_map_per_fmr in
.query_device(), but mlx4_core doesn't check it when actually
allocating FMRs.
Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum
value on FMR allocations.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
If the opcode of a work request exceeds the range of valid opcodes,
return the pointer to the offending work request.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Set up a response with appropriate error status and send it for MADs
that are not supported by a specific class/version.
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
Signed-off-by: Swapna Thete <swapna.thete@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Since create_comp_task() creates percpu kthread, it makes sense to use
kthread_create_on_node() to get proper NUMA affinity for kthread
stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
The current get portinfo handling filters the LID being sent,
changing zero to 0xffff.
This causes OpenSM to log excessive warning messages.
Reviewed-by: Edward Mascarenhas <edward.mascarenhas@qlogic.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Call irq_set_affinity_hint() to give userspace programs such as
irqbalance the information to be able to distribute qib interrupts
appropriately.
The logic allocates all non-receive interrupts to the first CPU local
to the HCA. Receive interrupts are allocated round robin starting
with the second CPU local to the HCA with potential wrap back to the
second CPU.
This patch also adds a refinement to the name registered for MSI-X
interrupts so that user level scripts can determine the device
associated with the IRQs when there are multiple HCAs with a
potentially different set of local CPUs.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix endianness problems detect by sparse, introduced with the enhanced
MPA patch.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tatyana Nikolova <Tatyana.E.Nikolova@intel.com>
Signed-off-by: Faisal Latif <Faisal.Latif@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Don't worry about p2p_type if peer2peer itself is not requested in the
first place.
Signed-off-by: Kumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Change the test for if a cmd is a tmr request to checking if
SCF_SCSI_TMR_CDB (a new flag) is set in cmd->se_cmd_flags.
Also remove se_tmr_req_cache usage in favor of kzalloc usage,
and make core_tmr_alloc_req() return int + setup se_cmd->se_tmr_req
directly and fix up various fabric module usages
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Replace various atomic_ts used as flags in struct se_cmd with a single
transport_state bitmap that requires t_state_lock to be held for modifications.
In the target core that assumption generally is true, but some recently added
code in the SRP target had to grow new lock calls. I can't say I like the way
how it messes with the command state directly, but let's leave that for later.
(Re-add missing ib_srpt.c changes that nab dropped..)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Conflicts:
drivers/infiniband/hw/nes/nes_cm.c
Simple whitespace conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quoth David:
1) GRO MAC header comparisons were ethernet specific, breaking other
link types. This required a multi-faceted fix to cure the originally
noted case (Infiniband), because IPoIB was lying about it's actual
hard header length. Thanks to Eric Dumazet, Roland Dreier, and
others.
2) Fix build failure when INET_UDP_DIAG is built in and ipv6 is modular.
From Anisse Astier.
3) Off by ones and other bug fixes in netprio_cgroup from Neil Horman.
4) ipv4 TCP reset generation needs to respect any network interface
binding from the socket, otherwise route lookups might give a
different result than all the other segments received. From Shawn
Lu.
5) Fix unintended regression in ipv4 proxy ARP responses, from Thomas
Graf.
6) Fix SKB under-allocation bug in sh_eth, from Yoshihiro Shimoda.
7) Revert skge PCI mapping changes that are causing crashes for some
folks, from Stephen Hemminger.
8) IPV4 route lookups fill in the wildcarded fields of the given flow
lookup key passed in, which is fine most of the time as this is
exactly what the caller's want. However there are a few cases that
want to retain the original flow key values afterwards, so handle
those cases properly. Fix from Julian Anastasov.
9) IGB/IXGBE VF lookup bug fixes from Greg Rose.
10) Properly null terminate filename passed to ethtool flash device
method, from Ben Hutchings.
11) S3 resume fix in via-velocity from David Lv.
12) Fix double SKB free during xmit failure in CAIF, from Dmitry
Tarnyagin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (72 commits)
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
netprio_cgroup: fix wrong memory access when NETPRIO_CGROUP=m
netprio_cgroup: don't allocate prio table when a device is registered
netprio_cgroup: fix an off-by-one bug
bna: fix error handling of bnad_get_flash_partition_by_offset()
isdn: type bug in isdn_net_header()
net: Make qdisc_skb_cb upper size bound explicit.
ixgbe: ethtool: stats user buffer overrun
ixgbe: dcb: up2tc mapping lost on disable/enable CEE DCB state
ixgbe: do not update real num queues when netdev is going away
ixgbe: Fix broken dependency on MAX_SKB_FRAGS being related to page size
ixgbe: Fix case of Tx Hang in PF with 32 VFs
ixgbe: fix vf lookup
igb: fix vf lookup
e1000: add dropped DMA receive enable back in for WoL
gro: more generic L2 header check
IPoIB: Stop lying about hard_header_len and use skb->cb to stash LL addresses
zd1211rw: firmware needs duration_id set to zero for non-pspoll frames
net: enable TC35815 for MIPS again
...
|
|
Correct spelling "alocate" to "allocate" in
drivers/infiniband/ulp/srpt/ib_srpt.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|