| Age | Commit message (Collapse) | Author |
|---|
|
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
|
|
This adds simple DT bindings for spear-keyboard controller.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
When platform keymap is not supplied to matrix_keypad_build_keymap()
and device tree support is enabled, try locating specified property
and load keymap from it. If property name is not defined, try using
"linux,keymap".
Based on earlier patch by Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Change matrix-keymap helper to be out-of-line, like sparse keymap,
allow the helper perform basic keymap validation and return errors,
and prepare for device tree support.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Jean-François Dagenais <jeff.dagenais@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Hi Dmitry,
On Wed, May 9, 2012 at 3:14 PM, Poddar, Sourav <sourav.poddar@ti.com> wrote:
> Hi Dmitry,
>
> I did some minor fixes to the patch which you suggested above and
> the keypad is functional now.
>
> Changes:
> - Move "pm_runtime_enable" before using "pm_runtime_get_sync".
>
> Sending the patch inlined..(also attached).
>
> From: G, Manjunath Kondaiah <manjugk@ti.com>
> Date: Mon, 10 Oct 2011 20:52:05 +0530
> Subject: [PATCH] Input: omap-keypad: dynamically handle register offsets
>
> Keypad controller register offsets are different for omap4
> and omap5. Handle these offsets through static mapping and
> assign these mappings during run time.
>
> Tested on omap4430 sdp with 3.4-rc3.
> Tested on omap5430evm with 3.1-custom kernel.
>
> Cc: Andrew Morton <akpm@linux-foundation.org>
> Signed-off-by: Felipe Balbi <balbi@ti.com>
> Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
> ---
> drivers/input/keyboard/Kconfig | 4 +-
> drivers/input/keyboard/omap4-keypad.c | 120 +++++++++++++++++++++++++-------
> 2 files changed, 95 insertions(+), 29 deletions(-)
>
> diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
> index f354813..33bbdee 100644
> --- a/drivers/input/keyboard/Kconfig
> +++ b/drivers/input/keyboard/Kconfig
> @@ -512,9 +512,9 @@ config KEYBOARD_OMAP
> module will be called omap-keypad.
>
> config KEYBOARD_OMAP4
> - tristate "TI OMAP4 keypad support"
> + tristate "TI OMAP4+ keypad support"
> help
> - Say Y here if you want to use the OMAP4 keypad.
> + Say Y here if you want to use the OMAP4+ keypad.
>
> To compile this driver as a module, choose M here: the
> module will be called omap4-keypad.
> diff --git a/drivers/input/keyboard/omap4-keypad.c
> b/drivers/input/keyboard/omap4-keypad.c
> index e809ac0..d7102e8 100644
> --- a/drivers/input/keyboard/omap4-keypad.c
> +++ b/drivers/input/keyboard/omap4-keypad.c
> @@ -68,19 +68,52 @@
>
> #define OMAP4_MASK_IRQSTATUSDISABLE 0xFFFF
>
> +enum {
> + KBD_REVISION_OMAP4 = 0,
> + KBD_REVISION_OMAP5,
> +};
> +
> struct omap4_keypad {
> struct input_dev *input;
>
> void __iomem *base;
> - int irq;
> + unsigned int irq;
>
> unsigned int rows;
> unsigned int cols;
> + u32 reg_offset;
> + u32 irqreg_offset;
> unsigned int row_shift;
> unsigned char key_state[8];
> unsigned short keymap[];
> };
>
> +static int kbd_readl(struct omap4_keypad *keypad_data, u32 offset)
> +{
> + return __raw_readl(keypad_data->base +
> + keypad_data->reg_offset + offset);
> +}
> +
> +static void kbd_writel(struct omap4_keypad *keypad_data, u32 offset, u32 value)
> +{
> + __raw_writel(value,
> + keypad_data->base + keypad_data->reg_offset + offset);
> +}
> +
> +static int kbd_read_irqreg(struct omap4_keypad *keypad_data, u32 offset)
> +{
> + return __raw_readl(keypad_data->base +
> + keypad_data->irqreg_offset + offset);
> +}
> +
> +static void kbd_write_irqreg(struct omap4_keypad *keypad_data,
> + u32 offset, u32 value)
> +{
> + __raw_writel(value,
> + keypad_data->base + keypad_data->irqreg_offset + offset);
> +}
> +
> +
> /* Interrupt handler */
> static irqreturn_t omap4_keypad_interrupt(int irq, void *dev_id)
> {
> @@ -91,12 +124,11 @@ static irqreturn_t omap4_keypad_interrupt(int
> irq, void *dev_id)
> u32 *new_state = (u32 *) key_state;
>
> /* Disable interrupts */
> - __raw_writel(OMAP4_VAL_IRQDISABLE,
> - keypad_data->base + OMAP4_KBD_IRQENABLE);
> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
> + OMAP4_VAL_IRQDISABLE);
>
> - *new_state = __raw_readl(keypad_data->base + OMAP4_KBD_FULLCODE31_0);
> - *(new_state + 1) = __raw_readl(keypad_data->base
> - + OMAP4_KBD_FULLCODE63_32);
> + *new_state = kbd_readl(keypad_data, OMAP4_KBD_FULLCODE31_0);
> + *(new_state + 1) = kbd_readl(keypad_data, OMAP4_KBD_FULLCODE63_32);
>
> for (row = 0; row < keypad_data->rows; row++) {
> changed = key_state[row] ^ keypad_data->key_state[row];
> @@ -121,12 +153,13 @@ static irqreturn_t omap4_keypad_interrupt(int
> irq, void *dev_id)
> sizeof(keypad_data->key_state));
>
> /* clear pending interrupts */
> - __raw_writel(__raw_readl(keypad_data->base + OMAP4_KBD_IRQSTATUS),
> - keypad_data->base + OMAP4_KBD_IRQSTATUS);
> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
> + kbd_read_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS));
>
> /* enable interrupts */
> - __raw_writel(OMAP4_DEF_IRQENABLE_EVENTEN | OMAP4_DEF_IRQENABLE_LONGKEY,
> - keypad_data->base + OMAP4_KBD_IRQENABLE);
> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
> + OMAP4_DEF_IRQENABLE_EVENTEN |
> + OMAP4_DEF_IRQENABLE_LONGKEY);
>
> return IRQ_HANDLED;
> }
> @@ -139,16 +172,17 @@ static int omap4_keypad_open(struct input_dev *input)
>
> disable_irq(keypad_data->irq);
>
> - __raw_writel(OMAP4_VAL_FUNCTIONALCFG,
> - keypad_data->base + OMAP4_KBD_CTRL);
> - __raw_writel(OMAP4_VAL_DEBOUNCINGTIME,
> - keypad_data->base + OMAP4_KBD_DEBOUNCINGTIME);
> - __raw_writel(OMAP4_VAL_IRQDISABLE,
> - keypad_data->base + OMAP4_KBD_IRQSTATUS);
> - __raw_writel(OMAP4_DEF_IRQENABLE_EVENTEN | OMAP4_DEF_IRQENABLE_LONGKEY,
> - keypad_data->base + OMAP4_KBD_IRQENABLE);
> - __raw_writel(OMAP4_DEF_WUP_EVENT_ENA | OMAP4_DEF_WUP_LONG_KEY_ENA,
> - keypad_data->base + OMAP4_KBD_WAKEUPENABLE);
> + kbd_writel(keypad_data, OMAP4_KBD_CTRL,
> + OMAP4_VAL_FUNCTIONALCFG);
> + kbd_writel(keypad_data, OMAP4_KBD_DEBOUNCINGTIME,
> + OMAP4_VAL_DEBOUNCINGTIME);
> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
> + OMAP4_VAL_IRQDISABLE);
> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
> + OMAP4_DEF_IRQENABLE_EVENTEN |
> + OMAP4_DEF_IRQENABLE_LONGKEY);
> + kbd_writel(keypad_data, OMAP4_KBD_WAKEUPENABLE,
> + OMAP4_DEF_WUP_EVENT_ENA | OMAP4_DEF_WUP_LONG_KEY_ENA);
>
> enable_irq(keypad_data->irq);
>
> @@ -162,12 +196,12 @@ static void omap4_keypad_close(struct input_dev *input)
> disable_irq(keypad_data->irq);
>
> /* Disable interrupts */
> - __raw_writel(OMAP4_VAL_IRQDISABLE,
> - keypad_data->base + OMAP4_KBD_IRQENABLE);
> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
> + OMAP4_VAL_IRQDISABLE);
>
> /* clear pending interrupts */
> - __raw_writel(__raw_readl(keypad_data->base + OMAP4_KBD_IRQSTATUS),
> - keypad_data->base + OMAP4_KBD_IRQSTATUS);
> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
> + kbd_read_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS));
>
> enable_irq(keypad_data->irq);
>
> @@ -182,6 +216,7 @@ static int __devinit omap4_keypad_probe(struct
> platform_device *pdev)
> struct resource *res;
> resource_size_t size;
> unsigned int row_shift, max_keys;
> + int rev;
> int irq;
> int error;
>
> @@ -241,11 +276,40 @@ static int __devinit omap4_keypad_probe(struct
> platform_device *pdev)
> keypad_data->rows = pdata->rows;
> keypad_data->cols = pdata->cols;
>
> + /*
> + * Enable clocks for the keypad module so that we can read
> + * revision register.
> + */
> + pm_runtime_enable(&pdev->dev);
> + error = pm_runtime_get_sync(&pdev->dev);
> + if (error) {
> + dev_err(&pdev->dev, "pm_runtime_get_sync() failed\n");
> + goto err_unmap;
> + }
> + rev = __raw_readl(keypad_data->base + OMAP4_KBD_REVISION);
> + rev &= 0x03 << 30;
> + rev >>= 30;
> + switch (rev) {
> + case KBD_REVISION_OMAP4:
> + keypad_data->reg_offset = 0x00;
> + keypad_data->irqreg_offset = 0x00;
> + break;
> + case KBD_REVISION_OMAP5:
> + keypad_data->reg_offset = 0x10;
> + keypad_data->irqreg_offset = 0x0c;
> + break;
> + default:
> + dev_err(&pdev->dev,
> + "Keypad reports unsupported revision %d", rev);
> + error = -EINVAL;
> + goto err_pm_put_sync;
> + }
> +
> /* input device allocation */
> keypad_data->input = input_dev = input_allocate_device();
> if (!input_dev) {
> error = -ENOMEM;
> - goto err_unmap;
> + goto err_pm_put_sync;
> }
>
> input_dev->name = pdev->name;
> @@ -273,14 +337,14 @@ static int __devinit omap4_keypad_probe(struct
> platform_device *pdev)
> input_dev->keycode, input_dev->keybit);
>
> error = request_irq(keypad_data->irq, omap4_keypad_interrupt,
> - IRQF_TRIGGER_RISING,
> + IRQF_DISABLED | IRQF_TRIGGER_RISING,
Sorry, " IRQF_DISABLED" got included by mistake.
Removing this stray change and sending it again.
> "omap4-keypad", keypad_data);
> if (error) {
> dev_err(&pdev->dev, "failed to register interrupt\n");
> goto err_free_input;
> }
>
> - pm_runtime_enable(&pdev->dev);
> + pm_runtime_put_sync(&pdev->dev);
>
> error = input_register_device(keypad_data->input);
> if (error < 0) {
> @@ -296,6 +360,8 @@ err_pm_disable:
> free_irq(keypad_data->irq, keypad_data);
> err_free_input:
> input_free_device(input_dev);
> +err_pm_put_sync:
> + pm_runtime_put_sync(&pdev->dev);
> err_unmap:
> iounmap(keypad_data->base);
> err_release_mem:
>
>
> ~Sourav
>
> On Wed, May 9, 2012 at 1:15 PM, Dmitry Torokhov
> <dmitry.torokhov@gmail.com> wrote:
>>> Hi Dmitry ,
>>>
>>>
>>> On Wed, May 9, 2012 at 10:48 AM, Dmitry Torokhov
>>> <dmitry.torokhov@gmail.com> wrote:
>>> > Ho Sourav,
>>> >
>>> > On Thu, Apr 26, 2012 at 11:24:37AM +0530, Sourav Poddar wrote:
>>> >>
>>> >> -config KEYBOARD_OMAP4
>>> >> - tristate "TI OMAP4 keypad support"
>>> >> +config KEYBOARD_OMAP4+
>>> >
>>> > I think this works purely by accident - '+' sign getting dropped by
>>> > parser...
>>> >
>>> >> @@ -139,16 +192,33 @@ static int omap4_keypad_open(struct input_dev *input)
>>> >>
>>> >> disable_irq(keypad_data->irq);
>>> >>
>>> >> - __raw_writel(OMAP4_VAL_FUNCTIONALCFG,
>>> >> - keypad_data->base + OMAP4_KBD_CTRL);
>>> >> - __raw_writel(OMAP4_VAL_DEBOUNCINGTIME,
>>> >> - keypad_data->base + OMAP4_KBD_DEBOUNCINGTIME);
>>> >> - __raw_writel(OMAP4_VAL_IRQDISABLE,
>>> >> - keypad_data->base + OMAP4_KBD_IRQSTATUS);
>>> >> - __raw_writel(OMAP4_DEF_IRQENABLE_EVENTEN | OMAP4_DEF_IRQENABLE_LONGKEY,
>>> >> - keypad_data->base + OMAP4_KBD_IRQENABLE);
>>> >> - __raw_writel(OMAP4_DEF_WUP_EVENT_ENA | OMAP4_DEF_WUP_LONG_KEY_ENA,
>>> >> - keypad_data->base + OMAP4_KBD_WAKEUPENABLE);
>>> >> + keypad_data->revision = kbd_read_revision(keypad_data,
>>> >> + OMAP4_KBD_REVISION);
>>> >> + switch (keypad_data->revision) {
>>> >> + case 1:
>>> >> + keypad_data->irqstatus = OMAP4_KBD_IRQSTATUS + 0x0c;
>>> >> + keypad_data->irqenable = OMAP4_KBD_IRQENABLE + 0x0c;
>>> >> + keypad_data->reg_offset = 0x10;
>>> >> + break;
>>> >
>>> > This should be done in probe().
>>> >
>>> Dont we then require "pm_runtime_put_sync" in probe, since we are trying
>>> to read the keypad revision register.?
>>
>> Ah, indeed, but I think not pm_runtime_get_sync() but
>> pm_runtime_set_active().
>>
>> Not sure if this will fix the crash...
>>
>> --
>> Dmitry
>>
>>
>> Input: omap-keypad - dynamically handle register offsets
>>
>> From: G, Manjunath Kondaiah <manjugk@ti.com>
>>
>> Keypad controller register offsets are different for omap4
>> and omap5. Handle these offsets through static mapping and
>> assign these mappings during run time.
>>
>> Tested on omap4430 sdp with 3.4-rc3.
>> Tested on omap5430evm with 3.1-custom kernel.
>>
>> Signed-off-by: Felipe Balbi <balbi@ti.com>
>> Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
>> Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
>> Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
>> ---
>>
>> drivers/input/keyboard/Kconfig | 4 +
>> drivers/input/keyboard/omap4-keypad.c | 117 ++++++++++++++++++++++++++-------
>> 2 files changed, 94 insertions(+), 27 deletions(-)
>>
>>
>> diff --git a/drivers/input/keyboard/Kconfig b/drivers/input/keyboard/Kconfig
>> index 20a3753..84ee155 100644
>> --- a/drivers/input/keyboard/Kconfig
>> +++ b/drivers/input/keyboard/Kconfig
>> @@ -531,9 +531,9 @@ config KEYBOARD_OMAP
>> module will be called omap-keypad.
>>
>> config KEYBOARD_OMAP4
>> - tristate "TI OMAP4 keypad support"
>> + tristate "TI OMAP4+ keypad support"
>> help
>> - Say Y here if you want to use the OMAP4 keypad.
>> + Say Y here if you want to use the OMAP4+ keypad.
>>
>> To compile this driver as a module, choose M here: the
>> module will be called omap4-keypad.
>> diff --git a/drivers/input/keyboard/omap4-keypad.c b/drivers/input/keyboard/omap4-keypad.c
>> index e809ac0..c9fd0df 100644
>> --- a/drivers/input/keyboard/omap4-keypad.c
>> +++ b/drivers/input/keyboard/omap4-keypad.c
>> @@ -68,19 +68,52 @@
>>
>> #define OMAP4_MASK_IRQSTATUSDISABLE 0xFFFF
>>
>> +enum {
>> + KBD_REVISION_OMAP4 = 0,
>> + KBD_REVISION_OMAP5,
>> +};
>> +
>> struct omap4_keypad {
>> struct input_dev *input;
>>
>> void __iomem *base;
>> - int irq;
>> + unsigned int irq;
>>
>> unsigned int rows;
>> unsigned int cols;
>> + u32 reg_offset;
>> + u32 irqreg_offset;
>> unsigned int row_shift;
>> unsigned char key_state[8];
>> unsigned short keymap[];
>> };
>>
>> +static int kbd_readl(struct omap4_keypad *keypad_data, u32 offset)
>> +{
>> + return __raw_readl(keypad_data->base +
>> + keypad_data->reg_offset + offset);
>> +}
>> +
>> +static void kbd_writel(struct omap4_keypad *keypad_data, u32 offset, u32 value)
>> +{
>> + __raw_writel(value,
>> + keypad_data->base + keypad_data->reg_offset + offset);
>> +}
>> +
>> +static int kbd_read_irqreg(struct omap4_keypad *keypad_data, u32 offset)
>> +{
>> + return __raw_readl(keypad_data->base +
>> + keypad_data->irqreg_offset + offset);
>> +}
>> +
>> +static void kbd_write_irqreg(struct omap4_keypad *keypad_data,
>> + u32 offset, u32 value)
>> +{
>> + __raw_writel(value,
>> + keypad_data->base + keypad_data->irqreg_offset + offset);
>> +}
>> +
>> +
>> /* Interrupt handler */
>> static irqreturn_t omap4_keypad_interrupt(int irq, void *dev_id)
>> {
>> @@ -91,12 +124,11 @@ static irqreturn_t omap4_keypad_interrupt(int irq, void *dev_id)
>> u32 *new_state = (u32 *) key_state;
>>
>> /* Disable interrupts */
>> - __raw_writel(OMAP4_VAL_IRQDISABLE,
>> - keypad_data->base + OMAP4_KBD_IRQENABLE);
>> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
>> + OMAP4_VAL_IRQDISABLE);
>>
>> - *new_state = __raw_readl(keypad_data->base + OMAP4_KBD_FULLCODE31_0);
>> - *(new_state + 1) = __raw_readl(keypad_data->base
>> - + OMAP4_KBD_FULLCODE63_32);
>> + *new_state = kbd_readl(keypad_data, OMAP4_KBD_FULLCODE31_0);
>> + *(new_state + 1) = kbd_readl(keypad_data, OMAP4_KBD_FULLCODE63_32);
>>
>> for (row = 0; row < keypad_data->rows; row++) {
>> changed = key_state[row] ^ keypad_data->key_state[row];
>> @@ -121,12 +153,13 @@ static irqreturn_t omap4_keypad_interrupt(int irq, void *dev_id)
>> sizeof(keypad_data->key_state));
>>
>> /* clear pending interrupts */
>> - __raw_writel(__raw_readl(keypad_data->base + OMAP4_KBD_IRQSTATUS),
>> - keypad_data->base + OMAP4_KBD_IRQSTATUS);
>> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
>> + kbd_read_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS));
>>
>> /* enable interrupts */
>> - __raw_writel(OMAP4_DEF_IRQENABLE_EVENTEN | OMAP4_DEF_IRQENABLE_LONGKEY,
>> - keypad_data->base + OMAP4_KBD_IRQENABLE);
>> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
>> + OMAP4_DEF_IRQENABLE_EVENTEN |
>> + OMAP4_DEF_IRQENABLE_LONGKEY);
>>
>> return IRQ_HANDLED;
>> }
>> @@ -139,16 +172,17 @@ static int omap4_keypad_open(struct input_dev *input)
>>
>> disable_irq(keypad_data->irq);
>>
>> - __raw_writel(OMAP4_VAL_FUNCTIONALCFG,
>> - keypad_data->base + OMAP4_KBD_CTRL);
>> - __raw_writel(OMAP4_VAL_DEBOUNCINGTIME,
>> - keypad_data->base + OMAP4_KBD_DEBOUNCINGTIME);
>> - __raw_writel(OMAP4_VAL_IRQDISABLE,
>> - keypad_data->base + OMAP4_KBD_IRQSTATUS);
>> - __raw_writel(OMAP4_DEF_IRQENABLE_EVENTEN | OMAP4_DEF_IRQENABLE_LONGKEY,
>> - keypad_data->base + OMAP4_KBD_IRQENABLE);
>> - __raw_writel(OMAP4_DEF_WUP_EVENT_ENA | OMAP4_DEF_WUP_LONG_KEY_ENA,
>> - keypad_data->base + OMAP4_KBD_WAKEUPENABLE);
>> + kbd_writel(keypad_data, OMAP4_KBD_CTRL,
>> + OMAP4_VAL_FUNCTIONALCFG);
>> + kbd_writel(keypad_data, OMAP4_KBD_DEBOUNCINGTIME,
>> + OMAP4_VAL_DEBOUNCINGTIME);
>> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
>> + OMAP4_VAL_IRQDISABLE);
>> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
>> + OMAP4_DEF_IRQENABLE_EVENTEN |
>> + OMAP4_DEF_IRQENABLE_LONGKEY);
>> + kbd_writel(keypad_data, OMAP4_KBD_WAKEUPENABLE,
>> + OMAP4_DEF_WUP_EVENT_ENA | OMAP4_DEF_WUP_LONG_KEY_ENA);
>>
>> enable_irq(keypad_data->irq);
>>
>> @@ -162,12 +196,12 @@ static void omap4_keypad_close(struct input_dev *input)
>> disable_irq(keypad_data->irq);
>>
>> /* Disable interrupts */
>> - __raw_writel(OMAP4_VAL_IRQDISABLE,
>> - keypad_data->base + OMAP4_KBD_IRQENABLE);
>> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQENABLE,
>> + OMAP4_VAL_IRQDISABLE);
>>
>> /* clear pending interrupts */
>> - __raw_writel(__raw_readl(keypad_data->base + OMAP4_KBD_IRQSTATUS),
>> - keypad_data->base + OMAP4_KBD_IRQSTATUS);
>> + kbd_write_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS,
>> + kbd_read_irqreg(keypad_data, OMAP4_KBD_IRQSTATUS));
>>
>> enable_irq(keypad_data->irq);
>>
>> @@ -182,6 +216,7 @@ static int __devinit omap4_keypad_probe(struct platform_device *pdev)
>> struct resource *res;
>> resource_size_t size;
>> unsigned int row_shift, max_keys;
>> + int rev;
>> int irq;
>> int error;
>>
>> @@ -241,11 +276,40 @@ static int __devinit omap4_keypad_probe(struct platform_device *pdev)
>> keypad_data->rows = pdata->rows;
>> keypad_data->cols = pdata->cols;
>>
>> + /*
>> + * Mark device as active (and wake up its parent) so we can read
>> + * revision register.
>> + */
>> + error = pm_runtime_set_active(&pdev->dev);
>> + if (error) {
>> + dev_err(&pdev->dev, "pm_runtime_set_active() failed\n");
>> + goto err_unmap;
>> + }
>> +
>> + rev = __raw_readl(keypad_data->base + OMAP4_KBD_REVISION);
>> + rev &= 0x03 << 30;
>> + rev >>= 30;
>> + switch (rev) {
>> + case KBD_REVISION_OMAP4:
>> + keypad_data->reg_offset = 0x00;
>> + keypad_data->irqreg_offset = 0x00;
>> + break;
>> + case KBD_REVISION_OMAP5:
>> + keypad_data->reg_offset = 0x10;
>> + keypad_data->irqreg_offset = 0x0c;
>> + break;
>> + default:
>> + dev_err(&pdev->dev,
>> + "Keypad reports unsupported revision %d", rev);
>> + error = -EINVAL;
>> + goto err_pm_suspended;
>> + }
>> +
>> /* input device allocation */
>> keypad_data->input = input_dev = input_allocate_device();
>> if (!input_dev) {
>> error = -ENOMEM;
>> - goto err_unmap;
>> + goto err_pm_suspended;
>> }
>>
>> input_dev->name = pdev->name;
>> @@ -281,6 +345,7 @@ static int __devinit omap4_keypad_probe(struct platform_device *pdev)
>> }
>>
>> pm_runtime_enable(&pdev->dev);
>> + pm_runtime_put_sync(&pdev->dev);
>>
>> error = input_register_device(keypad_data->input);
>> if (error < 0) {
>> @@ -296,6 +361,8 @@ err_pm_disable:
>> free_irq(keypad_data->irq, keypad_data);
>> err_free_input:
>> input_free_device(input_dev);
>> +err_pm_suspended:
>> + pm_runtime_set_suspended(&pdev->dev);
>> err_unmap:
>> iounmap(keypad_data->base);
>> err_release_mem:
From: G, Manjunath Kondaiah <manjugk@ti.com>
Date: Mon, 10 Oct 2011 20:52:05 +0530
Subject: [PATCH] Input: omap-keypad: dynamically handle register offsets
Keypad controller register offsets are different for omap4
and omap5. Handle these offsets through static mapping and
assign these mappings during run time.
Tested on omap4430 sdp with 3.4-rc3.
Tested on omap5430evm with 3.1-custom kernel.
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Direct keys usage may not start from KP_DKIN0, add a msk option
to configure the specifics for platforms that can skip some keys.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
KPDK_DK only indicates the pin level of direct key.
So it is related to board, and low level may be active which
indicates that a key is pressed.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
When direcct_key_num is 0, the mask should be 0.
When direcct_key_num is 1, the mask should be 0b1.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
When the keypad is used as wake up source, the clock can not
be disabled. Or it can not detect key pressing.
If the keypad is used as wake up source, when resume back,
do not enable the clock and configure it again because the
register content is retained.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
|
|
I believe that "trying to access hardware" is more correct English
than "trying access hardware".
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
settle_time and debounce_period are u8 and thus can not be greater than
TC3589x_MAX_DEBOUNCE_SETTLE which is 255.
There also no need to mask out nibbles form board->krow and board->kcol
as we validate that they are in correct range.
Reported-by: Werner <w.landgraf@ru.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Instead of allocating and managing keymap separately from the keypad
structure stick it at the end as a variable-length array.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
SIMPLE_DEV_PM_OPS already defines constant dev_pm_ops.
Also guard PM methods with CONFIG_PM_SLEEP and get rid of some
unneeded #ifdefs.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Also use CONFIG_PM_SLEEP instead of CONFIG_PM to guard PM methods.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This patch converts the drivers in drivers/input/* to use
module_serio_driver() macro which makes the code smaller and
a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This driver adds support for the keypad part of the LM8333 and is
prepared for possible GPIO/PWM drivers. Note that this is not a MFD
because you cannot disable the keypad functionality which, thus,
has to be handled by the core anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull 2nd round of input updates from Dmitry Torokhov:
- update to Wacom driver to support wireless devices
- update to Sentelci touchpad driver to support newer hardware
- update to gpio-keys driver to support "interrupt-only" keys
- fixups to earlier commits
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wacom - check for allocation failure in probe()
Input: tegra-kbc - allocate pdata before using it
Input: amijoy - add missing platform check
Input: wacom - wireless battery status
Input: wacom - create inputs when wireless connect
Input: wacom - wireless monitor framework
Input: wacom - isolate input registration
Input: sentelic - improve packet debugging information
Input: sentelic - minor code cleanup
Input: sentelic - enabling absolute coordinates output for newer hardware
Input: sentelic - refactor code for upcoming new hardware support
Input: gpio_keys - add support for interrupt only keys
Input: gpio_keys - consolidate key destructor code
Input: revert "gpio_keys - switch to using threaded IRQs"
Input: gpio_keys - constify platform data
Input: spear-keyboard - remove kbd_set_plat_data()
|
|
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
|
|
Following commit broke DT support for tegra-kbc by removing pdata
allocation completely:
commit 023cea0ecfa2df034096c3f4afa796a0b2d1188a
Author: Shridhar Rasal <srasal@nvidia.com>
Date: Fri Feb 3 00:27:30 2012 -0800
Input: tegra-kbc - allow skipping setting up some of GPIO pins
This patch restores it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
In preparation for sa11x0 sparse irq conversion, explicitly include
mach/irqs.h as it will not be included for sparse irq.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Some of buttons, like power-on key or onkey, may only generate interrupts
when pressed and not actually be mapped as gpio in the system. Allow
setting gpio to invalid value and specify IRQ instead to support such
keys. The debounce timer is used not to debounce but to ignore new IRQs
coming while button is kept pressed.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
request_any_context_irq() should handle the case when using GPIO expanders
that themselves use threaded IRQs, and so the premise of change
7e2ecdf438bb479e2b4667fc16b1a84d6348da04 is incorrect.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
The platform data should not be altered and therefore should be
accessed through const pointers.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This patch converts the drivers in drivers/input/* to use the
module_i2c_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This patch allows us to drop the OMAP dependency from the OMAP4 keypad
driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This is an incremental patch updating to the revised bindings for
matrix keyboards.
This includes an optional "linux,fn-keymap" binding that is not yet
implemented, that will be used to specify the Fn-key modifier layout
if needed.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This adds a simple device tree binding for simple key matrix data and
a helper to fill in the platform data.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
|
|
Thaw and poweroff routines are missing for spear-keyboard. They are
required for:
- Error case scenarios during freeze
- Using test features, of hibernate.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Let platform pass mode information to keyboard driver according to which
it configures itself. The mode can be
- KEYPAD_9x9 0
- KEYPAD_6x6 1
- KEYPAD_2x2 2
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Lenovo Ideapad U455 to 'reset' blacklist
Input: serio_raw - return proper result when serio_raw_read fails
Input: document device properties
Input: twl4030_keypad - fix comment (trivial)
Input: gpio_keys - fix struct device declared inside parameter list
Input: evdev - fix variable initialisation
|
|
Allow marking some of GPIO pins as ignored to to avoid continuously
generating KBC input events.
Signed-off-by: Shridhar Rasal <srasal@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
And trivial whitespace fixes.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Enable keypress interrupt to support wakeup from low power state.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
We don't actually care if the device has been runtime suspended immediately
so we can just drop the reference without waiting for any state change to
be implemented. This may allow us to avoid some suspend/resume cycles and
is a bit more friendly to the rest of the system.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Also proper guard for system suspend/resume methods is CONFIG_PM_SLEEP,
not CONFIG_PM.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Because we are using platform_device_probe() to register the driver
we do not need to assign driver's probe method. We also can mark
ske_keypad_probe(), together with ske_keypad_chip_init(), as __init
instead of __devinit.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: bcm5974 - set BUTTONPAD property
Input: serio_raw - return proper result when serio_raw_write fails
Input: serio_raw - really signal HUP upon disconnect
Input: serio_raw - remove stray semicolon
Input: revert some over-zealous conversions to module_platform_driver()
|
|
Recent conversion to module_platform_driver() went a bit too far and
converted not only drivers that used platform_driver_register() but
also ones using platform_driver_probe(), breaking them in process.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tc3589x-keypad - add missing kerneldoc
Input: ucb1400-ts - switch to using dev_xxx() for diagnostic messages
Input: ucb1400_ts - convert to threaded IRQ
Input: ucb1400_ts - drop inline annotations
Input: usb1400_ts - add __devinit/__devexit section annotations
Input: ucb1400_ts - set driver owner
Input: ucb1400_ts - convert to use dev_pm_ops
Input: psmouse - make sure we do not use stale methods
Input: evdev - do not block waiting for an event if fd is nonblock
Input: evdev - if no events and non-block, return EAGAIN not 0
Input: evdev - only allow reading events if a full packet is present
Input: add driver for pixcir i2c touchscreens
Input: samsung-keypad - implement runtime power management support
Input: tegra-kbc - report wakeup key for some platforms
Input: tegra-kbc - add device tree bindings
Input: add driver for AUO In-Cell touchscreens using pixcir ICs
Input: mpu3050 - configure the sampling method
Input: mpu3050 - ensure we enable interrupts
Input: mpu3050 - add of_match table for device-tree probing
Input: sentelic - document the latest hardware
...
Fix up fairly trivial conflicts (device tree matching conflicting with
some independent cleanups) in drivers/input/keyboard/samsung-keypad.c
|
|
This adds two missing kerneldoc entries for the TC3589x
keypad driver.
Signed-off-by: Naga Radhesh <naga.radheshy@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
When runtime power management is enabled put the Samsung keypad driver
into suspend mode with wakeups disabled whenever the device is open but
a key is not actually been pressed. As well as saving a trivial amount of
power this will support the use of SoC wide idle modes which put the entire
device into a retention mode and use explicit wakeup sources to exit.
Since not all of the interrupt controllers used with the driver support
set_irq_wake() (though they all do the right thing) and there's a nasty
WARN() when we disable wake after failing to enable it keep track of the
current wake status from runtime PM and only disable wake if we managed
to enable it; I'm not entirely sure why this doesn't affect the existing
uses of the API in the driver.
System suspend is unaffected as the driver core will runtime resume any
suspended devices prior to system suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
drivers/input/keyboard/samsung-keypad.c
|
|
Tegra kbc cannot detect exact keypress causing wakeup in interrupt mode.
Allow wakeup keypress to be reported for certain platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
This adds a simple device tree binding to the tegra keyboard controller.
Also, mark the default keymap as __devinitdata since it is not referenced
after boot.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
|
Add device tree based discovery support for Samsung's keypad controller.
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
These symbols are not used outside it's driver so no need to
make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
|
