| Age | Commit message (Collapse) | Author |
|---|
|
Add support for the "Elitegroup ECS TVP3XP FM1246", the "KWorld DVB-T
210", and the Animation Technologies LR214 Rev F onwards (SAA7131) to
the saa7134 driver.
Also rename the LR214WF to the LR214 Rev E or ealier (SAA7135), to match
what we've seen on boards in the field.
Changed the comment on the Lifeview cards to indicate Rev E and earlier
versus Rev F and later, together with a chip indicator, following
feedback from Peter Missel <peter.missel@onlinehome.de>.
Signed-off-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
When the tuner is attached, the tda10046 is not initilized yet, so it
is searching for its firmware. If the tuner is attached to the tda10046
silent i2c port, a bus collision can occur. Now the version is probed
during the first init or sleep call.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The new name fits to what it is and what is on the box.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There are 2 new entries for p7131 boards and one correction for a board
with LNA.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Static locals should not be changed - the original contents gets lost.
Thanks to Trent Piepho for pointing me to this.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Change some debug messages from printk() to dprintk().
Add KERN_WARNING and KERN_ERR level indicators to other printk()s that
lacked them.
Format printk lines with consistent ("%s/dvb: ", dev->name) prefix.
Fixed dprintk macro, which had an if with no else that wasn't protected
with a do {} while(0) block. That leads to "if(...) dprintk(); else" not
doing what one would expect.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- The i2c data buffer in tda827xa_set_params was 1 byte too short
- saa7134-dvb now gives an error mesage if tda827x could not be attached
- coding style fix in tda1004x.c
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This is for better consistency with other drivers
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The hardware is completely initialized afterwards, especially the
tda10046 has its firmware - which is also necessary in analog mode
of some hybrid boards.
Calling the sleep function afterwards saves power and definitely puts
hybrid boards into analog mode without additional code elsewere.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
During tuner attach, the pointers to host dev structure
are not set yet, so the I2c adapter needs to be accessed differently.
This patch also does some minor cleanup in the saa7134-dvb module.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The patch moves the tda827x dvb tuning code to a separate module
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch contains
- new tuning code for the tda827xa silicon tuner.
- controls the preamplifier of some boards with this tuner.
- support for the Philips Tiger S hybrid DVB-T reference design.
- reworked the saa7134-dvb modulue to get rid of most of the
small board specific functions.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There are the following changes:
- separate configuration of IF and GPIOs.
- set GPIOs before firmware load. This helps to avoid I2C address
collisions.
- if desired invert GPIOs at sleep (automatic return to analog mode of card).
- added 3 tuner configuration bytes to config stuct.
- added i2c gate address to config struct.
- moved _state struct declaration to header file to make it accessible
on board layer.
- added "conf_probed" to the state struct to allow i.e. probing for correct
tuner version.
- changed firmware load mechanism to always:
+ check if already loaded
+ try to boot from eeprom
+ try downlad from host
- corrected name of tda10046 firmware image (backward compatible).
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Add support for Terratec Cinergy HT PCI
Signed-off-by: Giorgio Moscardi <software@sukkology.net>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Fix a typo (use_frontent -> use_frontend) in saa7134-dvb.c.
Signed-off-by: Stephan Berberig <s.berberig@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This card (like some others) supports both, DVB-T and a DVB-S.
The patch adds an insmod option to select the frontend:
use_frontend=0 -> DVB-T
use_frontend=1 -> DVB-S
Signed-off-by: Nico Sabbi <nsabbi@tiscali.it>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This is a hybrid cardbus module. Besides the card support, i
modified the definition names for AGC and GPIO of the tda10046.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch adds support for the Hauppauge WinTV-HVR1110 DVB-T/Hybrid
Signed-off-by: Thomas Genty <tomlohave@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This board has the same PCI ID as the T200, so the exact board type
is determined from the eeprom.
The original patch was provided by Francis Barber <fedora@barber-family.id.au>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This card has no firmware eeprom. The old version still should not
need a firmware file due to an undocumented feature of the TDA10046.
The patch also includes Hermann Pitton's proposal for improved
antenna switch handling
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The gate control was moved to a separate function.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The driver supports analog TV, radio and DVB-T.
It is based on the preliminary patch by Pierluigi Rolando.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The board did not return to analog mode since the board specific
"demod sleep" function was not called.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This is a analog DVB-T hybrid board
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch forces the correct antenna input input in DVB-T
mode for this card.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This adds support for a hybrid PAL/DVB/FM card. Unfortunately I tested
only the DVB since I don't have any proper antenna available and I can
receive even the DVB just barely so; I can hear noise in the FM part but I
couldn't catch any station, then again I don't have an FM antenna either.
The PAL/FM and IR control data are based on what I harvested on the 'net.
Perhaps I or someone else will fix them if they turn out to be wrong.
Signed-off-by: Petr Baudis <pasky@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Add support for Acorp TV134DS and FlyDVB-S cards (both based on
tda10086+tda826x)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Replaced with dvb_attach()
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Analog TV, CVBS, S-video and DVB-T are working,
DVB-S not yet
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
pointer field inside dvb_frontend
The dvb_frontend_ops is a pointer inside dvb_frontend. That's why every demod-driver
is having a field of dvb_frontend_ops in its private-state-struct and
using the reference for filling the pointer-field in dvb_frontend.
- It saves at least two lines of code per demod-driver,
- reduces object size (one less dereference per frontend_ops-access),
- be coherent with dvb_tuner_ops,
- makes it a little bit easier for newbies to understand how it works and
- avoids stupid mistakes because you would have to copy the dvb_frontend_ops
always, before you could assign the static pointer directly, which was
dangerous.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
I had broken the mt352 tuning when a non-directly connected PLL was used -
uncommon, but this is what is used on the pinnacle card.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
I'd missed some of these out, breaking the av7110 tuning. I then checked for
more and added them in where necessary. They may not actually be necessary
in all these locations, but if not, they'll simply have no effect.
Add small delay to stv0299 pll gate control to fix tuning problems.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Don't try and set the tuner ops if the demod was not detected.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Johannes Stezenbach suggested this change - definite improvement.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Rename pll calls to appropriate tuner calls.
Remove pll functions from demod structures.
Hook tuner call into tuner_ops.
Attach dvb-pll where possible.
Add pll gate control calls where appropriate.
Move europa specific code from tda1104x into card driver using ops overrides
(this is how it should ebe done instead of hacking card specific code into
the demod driver).
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Currently in /sys/class/dvb/dvbX.demuxY/ we have:
dev
uevent
With the patch, we have (for a PCI DVB device):
dev
device -> ../../../devices/pci0000:00/0000:00:1e.0/0000:03:0d.0
uevent
So userspace tools can (finally) work out which physical device a DVB adapter
refers to. Previously you had to kinda look through dmesg and hope that it
hadn't been dumped out of the buffer. This makes debugging a lot easier if
the system has been up for a long time!
This is done by adding an extra 'struct device *' parameter to
dvb_register_adapter(). It will work with any kind of standard
linux 'device'. Additionally, if someone has an embedded system which does
things differently, they can simply supply 'NULL' and the behaviour will be
as before - the link will simply not appear.
Ack'd-by: Manu Abraham <manu@linuxtv.org>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
There seem to be many variants of this cards with different
feature sets. This entry supports
analog TV, CVBS and s-video input, FM radio and DVB-T
if they are supported by the hardware.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
deleted 2 semicolons at end of functions
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This patch adds DVB-T support, no DVB-S yet
Signed-off-by: Nico Sabbi <nsabbi@tiscali.it>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- fixed tda9886 port 2 setting
- turned remote control receiver off via saa7134 GPIO to avoid i2c hangs
- modified tda9886 client calls to direct i2c access to allow proper return
to analog mode
- allow mode change to V4L2_TUNER_DIGITAL_TV in tuner VIDIOC_S_FREQUENCY
client call
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- When tuning VSB, use ANT input
- When tuning QAM, use CABLE input
Signed-off-by: Curt Meyers <cmeyers@boilerbots.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Andrew Burri <andrew.burri@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
This is an analog / digital hybrid card.
Signed-off-by: Peter Hartshorn <p3r@users.sourceforge.net>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Analog and DVB-T are working, Remote not yet.
This card is based on the new LifeView design, there should be many variants.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Additionally to the card support, this changeset adds the option
tda10046lifeview to get_dvb_firmware to download tda10046 firmware
from LifeView's site.
Signed-off-by: Giampiero Giancipoli <gianci@libero.it>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
|
- Mark Typhoon cards as OEM of Lifeview.
Signed-off-by: Peter Missel <peter.missel@onlinehome.de>
Signed-off-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
|
