Age | Commit message (Collapse) | Author |
|
vidioc_s_tuner, vidioc_s_frequency and vidioc_s_register now
uses a constant argument. So, the driver reports warnings:
drivers/media/radio/radio-si476x.c:1196:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/media/radio/radio-si476x.c:1196:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_tuner') [enabled by default]
drivers/media/radio/radio-si476x.c:1199:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/media/radio/radio-si476x.c:1199:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_frequency') [enabled by default]
drivers/media/radio/radio-si476x.c:1209:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/media/radio/radio-si476x.c:1209:2: warning: (near initialization for 'si4761_ioctl_ops.vidioc_s_register') [enabled by default]
This is due to a (soft) merge conflict, as both this driver and the
const patches were applied for the same Kernel version.
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This commit adds a driver that exposes all the radio related
functionality of the Si476x series of chips via the V4L2 subsystem.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This commit introduces new class of standard controls
V4L2_CTRL_CLASS_FM_RX. This class is intended to all controls
pertaining to FM receiver chips. Also, two controls belonging to said
class are added as a part of this commit: V4L2_CID_TUNE_DEEMPHASIS and
V4L2_CID_RDS_RECEPTION.
This patch is based on the code found in the patch by Manjunatha Halli [1]
[1] http://lists-archives.com/linux-kernel/27641307-new-control-class-and-features-for-fm-rx.html
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If i run verbose v4l2-compliance with my radio-mr800 device few times
then i get warning about frequency out of range:
root@machine:~# v4l2-compliance -r /dev/radio0 -v 2
is radio
Driver Info:
Driver name : radio-mr800
Card type : AverMedia MR 800 USB FM Radio
Bus info : usb-0000:00:1a.0-1.2
Driver version: 3.9.0
Capabilities : 0x80050400
Tuner
Radio
Device Capabilities
Device Caps : 0x00050400
Tuner
Radio
Compliance test for device /dev/radio0 (not using libv4l2):
Required ioctls:
test VIDIOC_QUERYCAP: OK
Allow for multiple opens:
test second radio open: OK
test VIDIOC_QUERYCAP: OK
test VIDIOC_G/S_PRIORITY: OK
Debug ioctls:
test VIDIOC_DBG_G_CHIP_IDENT: OK (Not Supported)
test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported)
test VIDIOC_LOG_STATUS: OK
Input ioctls:
test VIDIOC_G/S_TUNER: OK
warn: v4l2-test-input-output.cpp(234): returned tuner 0 frequency out
of range (6550200 not in [1400000...1728000])
test VIDIOC_G/S_FREQUENCY: OK
test VIDIOC_S_HW_FREQ_SEEK: OK
test VIDIOC_ENUMAUDIO: OK (Not Supported)
test VIDIOC_G/S/ENUMINPUT: OK (Not Supported)
test VIDIOC_G/S_AUDIO: OK (Not Supported)
Inputs: 0 Audio Inputs: 0 Tuners: 1
Output ioctls:
test VIDIOC_G/S_MODULATOR: OK (Not Supported)
test VIDIOC_G/S_FREQUENCY: OK
test VIDIOC_ENUMAUDOUT: OK (Not Supported)
test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported)
test VIDIOC_G/S_AUDOUT: OK (Not Supported)
Outputs: 0 Audio Outputs: 0 Modulators: 0
Control ioctls:
info: checking v4l2_queryctrl of control 'User Controls' (0x00980001)
info: checking v4l2_queryctrl of control 'Mute' (0x00980909)
info: checking v4l2_queryctrl of control 'Mute' (0x00980909)
test VIDIOC_QUERYCTRL/MENU: OK
info: checking control 'User Controls' (0x00980001)
info: checking control 'Mute' (0x00980909)
test VIDIOC_G/S_CTRL: OK
info: checking extended control 'User Controls' (0x00980001)
info: checking extended control 'Mute' (0x00980909)
test VIDIOC_G/S/TRY_EXT_CTRLS: OK
info: checking control event 'User Controls' (0x00980001)
info: checking control event 'Mute' (0x00980909)
test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK
test VIDIOC_G/S_JPEGCOMP: OK (Not Supported)
Standard Controls: 2 Private Controls: 0
Input/Output configuration ioctls:
test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_PRESETS: OK (Not Supported)
test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported)
test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported)
Format ioctls:
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK (Not Supported)
test VIDIOC_G/S_PARM: OK (Not Supported)
test VIDIOC_G_FBUF: OK (Not Supported)
test VIDIOC_G_FMT: OK (Not Supported)
test VIDIOC_TRY_FMT: OK (Not Supported)
test VIDIOC_S_FMT: OK (Not Supported)
test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported)
Codec ioctls:
test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported)
test VIDIOC_G_ENC_INDEX: OK (Not Supported)
test VIDIOC_(TRY_)DECODER_CMD: OK (Not Supported)
Buffer ioctls:
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK (Not Supported)
Total: 38, Succeeded: 38, Failed: 0, Warnings: 1
Some printk() debugging showed that vidioc_s_hw_freq_seek() setups
radio->curfreq to out of range value (lines 395-396) and calls
amradio_set_freq() to set this frequency on device without any
out-of-range checks.
Patch protects from setting up frequency on device to incorrect value
moving clamp_t check inside amradio_set_freq. With this patch we can
call amradio_set_freq() with out of range frequency from any place.
Also put comment that sometimes radio->curfreq is set to out of range
value in vidioc_s_hw_freq_seek().
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The et61x251 driver was removed in v3.5. Remove the last references to
its Kconfig macro now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
ioctl's number is unsigned int. Fix it at vidioc_default.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This sensor is used by the "SpeedLink Vicious And Devine Laplace webcam" and
others. It supports resolutions up to 1600x1200 (at 7-8 fps), but for
resolutions higher than 640x480, further driver changes will be necessary,
such as sensor output resolution switching (including further configuration
changes), bridge xclk adjustment and disabling of 16 bit (12 bit) output formats
at high resolutions. Image quality should also needs to be improved.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The Windows driver also probes at least two further i2c addresses (0x22 >> 1
and 0x66 >> 1). I've got some hints that they are very likely used by Samsung
and Kodak sensors, which are known to be used in Empia devices, too.
We havn't seen any devices using these sensors yet and don't know how to probe
them properly, so leave a comment.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
OmniVision sensors are used as well in Empiatech based cameras such as the
"SpeedLink Vicious And Devine Laplace" webcam (EM2765 + Omnivision OV2640).
With this patch applied, OminiVision sensors with 8 bit address and register
width are detected (recent models have a 16 bit address width and use different
client addresses).
The most commonly used sensors (including the ones listed by Empiatech) are
detected properly, although there is no support for them yet.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Other sensors like the ones from OmniVision need a different probing procedure,
so it makes sense have separate functions for each manufacturer/sensor type.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add further Micron chip IDs to be able to identify all Micron sensors listed
by Empiatech.
Also probe the two alternate i2c addresses used by Micron sensors with 8 bit
address and 16 bit register width.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
em28xx-cards.c is very large and the sensor/camera related code is growing,
so move this code to a separate source code file em28xx-camera.c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Now that the board hints and the sensor initialization/configuration have been
separated, em28xx_detect_sensor() is the better name for this function.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Sensor detection and initialization/configuration are currently mixed together.
This works as long as all devices with a particular sensor are working with the
same board configuration. In the long run, this will be not sufficient, so
separate these both steps to make the code more flexible and future proof.
This also makes the code more consistent, because the initialization of the
MT9V011 sensor subdevice is already separated.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The current board hint code is mixed together with the sensor detection and
initialization code. It actually selects a board depending on the detected
sensor type only, with the result that 3 of the 6 webcam boards are currently
dead.
Separate it and move it to em28xx_hint_board() which already contains the board
hints for analog capturing+TV and DVB devices.
This way, we have all board hints at a common place which makes it easier
to extend the code and reduces the risk of regressions.
It also makes it possible again to use the boards EM2750_BOARD_DLCW_130,
EM2820_BOARD_VIDEOLOGY_20K14XUSB and EM2860_BOARD_NETGMBH_CAM (using the module
parameter "card").
NOTE: the current board hint logic for webcams is preserved. Not more not less.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
for all alt settings
Some devices without DVB support (such as the "Terratec Grabby" and
"Easycap DC-60") provide isochronous DVB USB endpoints with wMaxPacketSize set
to 0 bytes for all alt settings.
Ignore these endpoints and avoid registering a DVB device node and loading the
DVB driver extension.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
-ERANGE is the right error code when the value is outside of the menu
range, but -EINVAL must be reported for invalid values inside the range.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
family bridges
The Windows driver writes the output resolution to registers 0x34 (width / 16)
and 0x35 (height / 16) always.
We don't know yet what these registers are used for.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Streaming doesn't work with the EM2765 if bit 5 of the output format register
0x27 is set.
It's actually not clear if really has to be set for the other chips, but for
now let's keep it to avoid regressions and add a comment to the code.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
processing
The em25xx/em276x/em277x/em278x frame data format is different to the one used
by the em2710/em2750/em28xx chips.
With the recent cleanups and reorganization of the frame data processing code it
can be easily extended to support these devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This chip can be found in the SpeedLink VAD Laplace webcam (1ae7:9003 and 1ae7:9004).
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
operations
The webcam "SpeedLink VAD Laplace" (em2765 + ov2640) uses a special algorithm
for i2c communication with the sensor, which is connected to a second i2c bus.
We don't know yet how to find out which devices support/use it.
It's very likely used by all em25xx and em276x+ bridges.
Tests with other em28xx chips (em2820, em2882/em2883) show, that this
algorithm always succeeds there although no slave device is connected.
The algorithm likely also works for real i2c client devices (OV2640 uses SCCB),
because the Windows driver seems to use it for probing Samsung and Kodak
sensors.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
au8522_attach is dependent on CONFIG_DVB_AU8522_DTV, not CONFIG_DVB_AU8522.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add the missing unlock before return from function af9035_ctrl_msg()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If those callbacks fail, it should return zero, and not a random
value. The previous code assumed that all drivers would only change
signal strength if it succeeds, but this may not be true.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Now that those functions are only used when the corresponding
function calls are defined, we don't need to check if those
function calls are present at the structure before using it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
While the driver gets AFC from the tuner, it doesn't return it
back via V4L2 API due to a mistake at the return. fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If the tuner frontend does not support get_rf_strength, then don't set
the has_signal callback. Ditto for get_afc.
Both callbacks overwrite the signal and afc fields of struct v4l2_tuner
but that should only happen if the tuner can actually detect this. If
it can't, then it should leave those fields alone so other subdevices
can try and detect the signal/afc.
This fixes the bug where the au8522 detected a signal and then tuner-core
overwrote it with 0 since the xc5000 tuner does not support get_rf_strength.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- open/close/read and poll need to take the core lock as well.
- when the tuner goes to sleep we should set std_set_in_tuner_core
to 0 since the tuner loses the firmware at that time.
- initialize the tuner if std_set_in_tuner_core == 0 whenever:
1) g/s_tuner, s_std or s_frequency is called
2) read or poll is called
3) streamon is called
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
After loading the module the initial video routing is not setup.
Explicitly call s_input to get this right.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Just opening a device shouldn't have any side-effects.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Turn it into a simple function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The driver crashed when the device was disconnected while an application
still had a device node open. Fixed by using the release() callback of struct
v4l2_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Now that au0828 has been converted to the control framework these
compatilibity ops are no longer needed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Also get rid of unnecessary format type check.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- V4L2_CAP_AUDIO was set, but enumaudio was not implemented.
- audioset was never filled by enum_input
- ctrl_ainput was never updated when switching the video input
- g_audio was broken due to faulty logic: g_audio should set the
index, it doesn't receive it from the user.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
No code change, just fixing a wrong indentation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
- define an initial frequency
- return an error if g_frequency is called for an invalid tuner index
- get the clamped frequency value after setting it: i.e. the tuner driver
may clamp the given frequency to a valid frequency range and ctrl_freq
should get that actual clamped frequency.
- remove obsolete tuner type checks (done by the core).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add support for vidioc_g_chip_name, allowing AC97 to be implemented as a
second chip on the bridge with the name "ac97". v4l2-dbg can just match the
name with that string in order to detect a ac97-compliant set of registers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It was just a placeholder and we want to get rid of the AC97 matching
define.
Also replace MATCH_HOST with MATCH_BRIDGE since we are here anyway.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Simplify the debugging ioctls by creating the VIDIOC_DBG_G_CHIP_NAME ioctl.
This will eventually replace VIDIOC_DBG_G_CHIP_IDENT. Chip matching is done
by the name or index of subdevices or an index to a bridge chip. Most of this
can all be done automatically, so most drivers just need to provide get/set
register ops.
In particular, it is now possible to get/set subdev registers without
requiring assistance of the bridge driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
During the transition to sub-devices several years ago non-subdev drivers
had a ' at the end of their driver name to tell them apart from already
converted drivers. This check was a left-over from that time and can be
removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In vb2_buffer_done, it would be better the print the value of 'state'
(current state of buffer) than to print 'vb->state' which is always
VB2_BUF_STATE_ACTIVE.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
523a4f7fbcf856fb1c2a4850f44edea6738ee37b
Case: In AdLink MPG24 there is bt878 exists (it captures one frame of all video
inputs), Video Signal for it one transmits through tw2804 chip, so we can't
control ADC (shut on/off) on tw2804, as some another can use bttv capture way.
Signed-off-by: Volokh Konstantin <volokh84@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Using two separate tables to setup the registers for 50 or 60 hz is
better than the non-const table that is filled in at runtime.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|