summaryrefslogtreecommitdiff
path: root/drivers/media
AgeCommit message (Collapse)Author
2009-08-13V4L/DVB (12441): siano: read buffer overflowRoel Kluin
With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[]. Subsequently an attempt is made to load the firmware from the resulting filename. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12440): Use kzalloc for frontend states to have struct dvb_frontend ↵Matthias Schwarzott
properly This patch changes most frontend drivers to allocate their state structure via kzalloc and not kmalloc. This is done to properly initialize the embedded "struct dvb_frontend frontend" field, that they all have. The visible effect of this struct being uninitalized is, that the member "id" that is used to set the name of kernel thread is totally random. Some board drivers (for example cx88-dvb) set this "id" via videobuf_dvb_alloc_frontend but most do not. So I at least get random id values for saa7134, flexcop and ttpci based cards. It looks like this in dmesg: DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S) The related kernel thread then also gets a strange name like "kdvb-ad-1-fe--1". Cc: Michael Krufky <mkrufky@linuxtv.org> Cc: Steven Toth <stoth@linuxtv.org> Cc: Timothy Lee <timothy.lee@siriushk.com> Cc: Igor M. Liplianin <liplianin@me.by> Signed-off-by: Matthias Schwarzott <zzam@gentoo.org> Acked-by: Andreas Oberritter <obi@linuxtv.org> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12438): Read buffer overflowRoel Kluin
parport[n] is checked before n < MAX_CAMS Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12437): dvb: siano uses/depends on INPUTRandy Dunlap
siano uses input_*() functions so it should depend on INPUT to prevent build errors: ERROR: "input_event" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_register_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_free_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_unregister_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! ERROR: "input_allocate_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined! Cc: Michael Krufky <mkrufky@linuxtv.org> Cc: Uri Shkolnik <uris@siano-ms.com> Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12436): stk-webcam: read buffer overflowRoel Kluin
It tested the value of stk_sizes[i].m before checking whether i was in range. Cc: Hans Verkuil <hverkuil@xs4all.nl> Cc: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12432): em28xx: fix regression in Empire DualTV digital tuningDevin Heitmueller
Restore support for digital tuning caused by regression during introduction of disable_i2c_gate parameter to zl10353 driver. Thanks to user "Xwang" for reporting the problem and testing the fix Cc: Xwang <xwang1976@email.it> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12429): v4l2-ioctl: fix G_STD and G_PARM default handlersHans Verkuil
The v4l core supplies default handlers for G_STD and G_PARM. However, both default handlers are buggy. This patch fixes the following: 1) If no g_std is supplied and current_norm == 0, then this driver does not support TV video standards (e.g. a radio or webcam driver). Return -EINVAL. This ensures that there is no bogus VIDIOC_G_STD support for such drivers. 2) The default VIDIOC_G_PARM handler used current_norm instead of first checking if the driver supported g_std and calling that to get the norm. It also didn't check if current_norm was 0, since in that case the driver does not support TV standards (or no standard was set at all) and the default handler should return -EINVAL. Note that I am very unhappy with these default handlers: I think they basically behave like some very strange and unexpected side-effect. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12428): hdpvr: add missing initialization of current_normHans Verkuil
Drivers should either set current_norm or supply a g_std callback. The hdpvr driver does neither. Since it initializes to a 60 Hz format I've initialized the current_norm to NTSC | PAL_M | PAL_60 which is the 60 Hz subset of tvnorms. Cc: Janne Grunau <j@jannau.net> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12424): soc-camera: fix recursive locking in .buf_queue()Guennadi Liakhovetski
The .buf_queue() V4L2 driver method is called under spinlock_irqsave(q->irqlock,...), don't take the lock again inside the function. Reported-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12422): media/zr364xx: fix build errorsRandy Dunlap
Fix build errors in zr364xx by adding selects: zr364xx.c:(.text+0x195ed7): undefined reference to `videobuf_streamon' zr364xx.c:(.text+0x196030): undefined reference to `videobuf_dqbuf' zr364xx.c:(.text+0x1960c4): undefined reference to `videobuf_qbuf' zr364xx.c:(.text+0x196123): undefined reference to `videobuf_querybuf' zr364xx.c:(.text+0x196182): undefined reference to `videobuf_reqbufs' zr364xx.c:(.text+0x196224): undefined reference to `videobuf_queue_is_busy' zr364xx.c:(.text+0x196390): undefined reference to `videobuf_vmalloc_free' zr364xx.c:(.text+0x196571): undefined reference to `videobuf_iolock' zr364xx.c:(.text+0x196678): undefined reference to `videobuf_mmap_mapper' zr364xx.c:(.text+0x196760): undefined reference to `videobuf_poll_stream' zr364xx.c:(.text+0x19689a): undefined reference to `videobuf_read_one' zr364xx.c:(.text+0x1969ec): undefined reference to `videobuf_mmap_free' zr364xx.c:(.text+0x197862): undefined reference to `videobuf_queue_vmalloc_init' zr364xx.c:(.text+0x197a28): undefined reference to `videobuf_streamoff' zr364xx.c:(.text+0x198203): undefined reference to `videobuf_to_vmalloc' zr364xx.c:(.text+0x198603): undefined reference to `videobuf_streamoff' drivers/built-in.o: In function `free_buffer': zr364xx.c:(.text+0x19930c): undefined reference to `videobuf_vmalloc_free' drivers/built-in.o: In function `zr364xx_open': zr364xx.c:(.text+0x19a7de): undefined reference to `videobuf_queue_vmalloc_init' drivers/built-in.o: In function `read_pipe_completion': zr364xx.c:(.text+0x19b17f): undefined reference to `videobuf_to_vmalloc' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12405): em28xx-cards: move register 0x13 setting to the proper placeMauro Carvalho Chehab
Register 0x13 seems to be a sort of image control, maybe gamma, white level or black level. Lower values produce better images, while higher values increases the contrast and shifts colors to green. 0xff produces a black image. This register is not Silvercrest-specific, so its code should be moved to a better place. If this register is left alone, a random value can be found at the register, producing weird results. While here, let's remove register 0x0d, as it had no noticed effect at the image. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12411): em28xx: Fix artifacts with Silvercrest webcamMauro Carvalho Chehab
Silvercrest mt9v011 sensor produces a 640x480 image. However, previously, the code were getting only half of the lines and merging two consecutive frames to "produce" a 640x480 image. With the addition of progressive mode, now em28xx is working with a full image. However, when the number of lines is bigger than 240, the beginning of some odd lines are filled with blank. After lots of testing, and physically checking the device for a Xtal, it was noticed experimentally that mt9v011 is using em28xx XCLK as its clock. Due to that, changing XCLK value changes the maximum speed of the stream. At the tests, it were possible to produce up to 32 fps, using a 30 MHz XCLK. However, at that rate, the artifacts happen even at 320x240. Lower values of XCLK produces artifacts only at 640x480. At some values of xclk (for example XCLKK = 6 MHz, 640x480), it is possible to see an invalid sucession of artifacts with this pattern: .xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx .xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ..xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ...xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx ....xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx (where the dots represent the blanked pixels) So, it seems that a waveform in the format of a ramp is interferring at the image. The cause of this interference is currently unknown. Some possibilities are: - electrical interference (maybe this device is broken?); - some issue at mt9v011 programming; - some bug at em28xx chip. So, for now, let's be conservative and use a value of XCLK that we know for sure that it won't cause artifacts. As I'm waiting for more of such devices with different em28xx chipset revisions, I'll have the opportunity to double check the issue with other pieces of hardware. Later patches can vary XCLK depending on the vertical resolutions, if a proper fix is not discovered. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12410): em28xx: Move the non-board dependent part to be outside ↵Mauro Carvalho Chehab
em28xx_pre_card_setup() em28xx_pre_card_setup() is meant to contain board-specific initialization. Also, as autodetection sometimes occur only after having i2c bus enabled, this function may need to be called later. Moving those setups to happen outside the function avoids calling it twice without need and without duplicating output lines at dmesg. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12407): em28xx: Adjust Silvercrest xtal frequencyMauro Carvalho Chehab
We don't know the xtal frequency of Silvercrest, but we need to have some value in order to allow controlling the frame rate frequency. The value is probably still wrong, since the manufacturer announces this device as being capable of 30fps, but the maximum we can get is 13.5 fps. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12406): em28xx: fix: don't do image interlacing on webcamsMauro Carvalho Chehab
Due to historical reasons, em28xx driver gets two consecutive frames and fold them into an unique framing, doing interlacing. While this works fine for TV images, this produces two bad effects with webcams: 1) webcam images are progressive. Merging two consecutive images produce interlacing artifacts on the image; 2) since the driver needs to get two frames, it reduces the maximum frame rate by two. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12403): em28xx: properly reports some em2710 chipsMauro Carvalho Chehab
As reported by hermann pitton <hermann-pitton@arcor.de>, some devices has a different chip id for em2710 (likely the older ones): em28xx: New device @ 480 Mbps (eb1a:2710, interface 0, class 0) em28xx #0: Identified as EM2710/EM2750/EM2751 webcam grabber (card=22) em28xx #0: em28xx chip ID = 17 Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12402): em28xx: fix: some em2710 chips use a different vendor IDMauro Carvalho Chehab
Thanks to hermann pitton <hermann-pitton@arcor.de> for pointing this new variation. Tested-by: hermann pitton <hermann-pitton@arcor.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12401): m9v011: add vflip/hflip controls to control mirror/upside downMauro Carvalho Chehab
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12400): em28xx: Allow changing fps on webcamsMauro Carvalho Chehab
em28xx doesn't have temporal scaling. However, on webcams, sensors are capable of changing the output rate. So, VIDIOC_[G|S]_PARM ioctls should be passed to the sensor for it to properly set frame rate. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12399): mt9v011: Add support for controlling frame ratesMauro Carvalho Chehab
Implement g_parm/s_parm ioctls. Those are used to check the current frame rate (in fps) and to set it to a value. In practice, there are only 15 possible different speeds, due to chip limits. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12394): cx88: Disable xc3028 power management for Geniatech x8000Devin Heitmueller
A user discovered that the Geniatech x8000 encountered a regression when the xc3028 power management was introduced. The xc3028 never recovers after setting the powerdown register, which is probably because the xc3028 reset GPIO is not properly configured. Since I do not have access to the hardware and thus cannot determine the correct GPIO configuration, just disable xc3028 power management on this board, which fixes the regression. Thanks to user "ritec" for reporting the issue and testing the fix. Cc: rictec <rictec@netcabo.pt> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12393): cx88: fix regression in tuning for Geniatech X8000 MTDevin Heitmueller
The introduction of the zl10353 i2c gate control broke support for the Geniatech board (which is not behind an i2 gate). Add the needed parameter. Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12391): saa7134: Use correct product name for Hauppauge ↵Michael Krufky
WinTV-HVR1120 DVB-T/Hybrid Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12390): saa7134: Use correct product name for Hauppauge ↵Michael Krufky
WinTV-HVR1150 ATSC/QAM-Hybrid Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12386): sms1xxx: fix build warning: unused variable 'board'Michael Krufky
Remove the following build warning: sms-cards.c: In function 'sms_board_event': sms-cards.c:120: warning: unused variable 'board' Thanks to Hans Verkuil for pointing this out. The problem code has been #if 0'd for now, this will likely be used again in the future, once the event interface is complete. Cc: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12380): uvcvideo: Avoid flooding the kernel log with "unknown event ↵Laurent Pinchart
type" messages The iSight sends non-UVC status events through the interrupt endpoint. Those invalid events are reported to the kernel log, resulting in a log flood. Only log the events when the UVC_TRACE_STATUS flag is set. Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12328): uvcvideo: Don't apply the FIX_BANDWIDTH quirk to all ↵Laurent Pinchart
ViMicro devices Commit 50144aeeb702ea105697ae5249f059ea3990b838 broke the Samsung NC10 netbook webcam. Instead of applying the FIX_BANDWIDTH quirk to all ViMicro devices, list the devices explicitly. Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12374): sms1xxx: fix broken Hauppauge devicesMichael Krufky
The current GPIO configuration breaks all Hauppauge devices. The code being removed affects Hauppauge devices only, and is the cause of the breakage. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12371): af9015: Fix for crash in dvb-usb-af9015Nils Kassube
Moving BOOT fixes problem. Signed-off-by: Nils Kassube <kassube@gmx.net> Acked-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12362): cx23885-417: fix manipulation of tvnormsMichael Krufky
Currently, the VIDIOC_S_STD ioctl just returns -EINVAL regardless of the norm passed. This patch sets cx23885_mpeg_template.tvnorms and cx23885_mpeg_template.current_norm so that the VIDIOC_S_STD will work. Thanks to Joseph Yasi for pointing this out, even though this particular fix was already pushed into a development repository, merge priority of this changeset has been escalated as a result of Joseph posting this identical patch. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Joseph A. Yasi <joe.yasi@gmail.com> Reviewed-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12349): cx88: HVR1300 ensure switching from Encoder to DVB-T and ↵Sohail Syyed
back is reliable Current tip is broken and does not switch back to DVB-T correctly Signed-off-by: Sohail Syyed <linuxtv@hubstar.net> Signed-off-by: Steven Toth <stoth@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12344): em28xx: fix support for Plextor ConvertX PX-TV100UMauro Carvalho Chehab
This device uses msp34xx and uses 2.048 MHz frequency for I2S communication. Thanks to Angelo Cano <acano@fastmail.fm> for pointing the issues with this device and proposing an approach for fixing the issue. Tested-by: Angelo Cano <acano@fastmail.fm> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12341): zl10353 and qt1010: fix stack corruption bugJan Nikitenko
Fixes stack corruption bug present in dump_regs function of zl10353 and qt1010 drivers: the buffer buf was one byte smaller than required - there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom bytes per line and 1 byte for zero ending the string required, i.e. 53 bytes, but only 52 were provided. The one byte missing in stack based buffer buf can cause stack corruption possibly leading to kernel oops, as discovered originally with af9015 driver (af9015: fix stack corruption bug). Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12340): mtv9v011: Add a missing chip version to the driverMauro Carvalho Chehab
Some mt9v011 webcams report 0x8332 chip version, instead of 0x8243. From the revision history at the mt9v011 datasheet, it seems that the chip version has changed from the first release of the chip. Thanks-to hermann pitton <hermann-pitton@arcor.de> for pointing this to me, on his tests with a Silvercrest webcam. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12338): cx18: Read buffer overflowAndy Walls
This mistakenly tested against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Reported-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12337): ivtv: Read buffer overflowRoel Kluin
This mistakenly tests against sizeof(freqs) instead of the array size. Due to the mask the only illegal value possible was 3. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Andy Walls <awalls@radix.net> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-08-13V4L/DVB (12330): pxa_camera: Fix Oops in pxa_camera_probeAntonio Ospite
mclk_get_divisor uses pcdev->soc_host.dev, make sure it is initialized. Signed-off-by: Antonio Ospite <ospite@studenti.unina.it> Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macroMichael Krufky
When enabling debug with v4l_debug set to 2 or greater, the driver OOPS's on startup. Checks dev pointer before dereferencing, in order to prevent this OOPS. Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12302): cx23885-417: fix broken IOCTL handlingMichael Krufky
IOCTLS will never get handled if we dont connect video_ioctl2 to mpeg_fops.ioctl Signed-off-by: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tunerHans Verkuil
Both tvaudio and the tuner share i2c address 0x42. The tvaudio module can check whether it really is a tda9840, but the tuner can't. So the tvaudio module must be loaded before the tuner module. This was also the case for 2.6.29, but the order was swapped in 2.6.30. Thanks to Krzysztof Grygiencz for reporting and testing this. Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12291): b2c2: fix frontends compiled into kernelTrent Piepho
A recent patch didn't take into account that frontends can be compiled into the kernel. Or that frontends compiled as modules can't be used by the b2c2 driver if it is not a module itself. Some frontends require multiple drivers, e.g. a demod driver and a tuner driver. The code for the frontend support was getting added if the demod driver was available. Change this to also require any needed tuner or SEC drivers as well. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12286): sn9c20x: reorder includes to be like other driversMauro Carvalho Chehab
This is not just pure cosmetic, since the order affects the out-of-tree module build at the -hg development tree. Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg ↵Julia Lawall
header). Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges.Brian Johnson
Signed-off-by: Brian Johnson <brijohn@gmail.com> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and ↵Brian Johnson
vidioc_g/s_register. Signed-off-by: Brian Johnson <brijohn@gmail.com> Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by appAntti Palosaari
Request demodulator auto-detect transmission parameters in case of garbage parameters provided by application for compatibility. That's needed at least for MPlayer compatibility currently. Thanks to Jelle de Jong for reporting issue and providing SSH access to Devin for debugging. Thanks to Devin Heitmueller for hard debug work he did to find that bug. Cc: Devin Heitmueller <dheitmueller@kernellabs.com> Cc: Jelle de Jong <jelledejong@powercraft.nl> Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors.Jean-Francois Moine
The bug was introduced when adding the light frequency control Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1)Devin Heitmueller
When the change was introduced in the zl10353 for the i2c gate behavior, this broke the HVR-900 which was not behind a gate. Use a version of the zl10353 config profile that indicates the tuner is not behind such a gate. Without this patch the first tune succeeds, but subsequent tuning attempts will fail. The change also renames the terratec zl10353 profile I wrote to be more generic, since it is shared by the non-terratec device. Thanks to Michael Krufky for providing a HVR-900 and DVB-T environment to test with. Cc: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320eDevin Heitmueller
The Pinnacle Hybrid Pro 320e was missing a demod config for the xc3028, which is required for digital tuning to work properly. Add the missing profile. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment. Cc: Andreas Lunderhage <lunderhage@home.se> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
2009-07-24V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia ↵Devin Heitmueller
USB id was used In cases where the device has a generic Empia USB ID, the call in the precard setup phase did not set the tuner GPIO. As a result, the tuner may not be taken out of reset before attempting initialization in the analog driver. This problem was not seen before with the EVGA inDtube, since that particular board has the analog GPIO setup to include taking the tuner out of reset. Thanks to Andreas Lunderhage for testing patches and providing a remote debug environment for the Pinnacle 320e. Cc: Andreas Lunderhage <lunderhage@home.se> Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>