Age | Commit message (Collapse) | Author |
|
Fix two compile errors below,
error: implicit declaration of function 'of_iomap'
error: implicit declaration of function 'out_be32'
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
|
|
The eSDHC is not compatible with SD spec well, so we need
to use eSDHC-specific code to switch to SDR50 mode.
1. IO signal voltage switching, eSDHC uses SDHC_VS to switch
io voltage and it's needed to configure a global utilities
register SCFG_SDHCIOVSELCR(if it has) and SDHC_VS signal.
2. Before executing tuning procedure, eSDHC should set its own
tuning block.
static const struct sdhci_ops sdhci_esdhc_ops = {
...
.set_tuning_block = esdhc_set_tuning_block,
.signal_voltage_switch = esdhc_signal_voltage_switch,
};
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
|
|
The eSDHC is not compatible with SD spec well, it's needed
to add callbacks for signal voltage switching and tuning
block setting for eSDHC for eMMC45 Adapter Card HS200 mode
support.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
|
|
Rather than wasting cycles read-modify-writing the interrupt enable
registers, cache the value locally instead.
This patch is from upstreaming linux, commit id
b537f94ce19583de1882f539a5cc49aa99260aca
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Change-Id: I3c1bb4d4b3f7d7dccbaa4748816bfe381edc484c
Reviewed-on: http://git.am.freescale.net:8181/37869
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
|
|
Enable interrupt mode to detect card instead of polling mode for
ls1021a by removing the quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION.
This could improve data transferring performance and avoid the call
trace caused by polling card status sometime.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Change-Id: Id965cd89b16f3f4d8327f1ca3d7ba9ed146e7a44
Reviewed-on: http://git.am.freescale.net:8181/37819
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
|
|
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Change-Id: I8ff8ea59c97e562cd0786b81165ccc944670e1f2
Reviewed-on: http://git.am.freescale.net:8181/30874
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Honghua Yin <Hong-Hua.Yin@freescale.com>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
arch/arm/kvm/mmu.c
arch/arm/mm/proc-v7-3level.S
arch/powerpc/kernel/vdso32/getcpu.S
drivers/crypto/caam/error.c
drivers/crypto/caam/sg_sw_sec4.h
drivers/usb/host/ehci-fsl.c
|
|
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
|
|
The T4160 is a lower power version of the T4240, and The T4080 is a low
power version of the T4160. So they have the same eSDHC controller.
Signed-off-by: Li Jingyu <b41874@freescale.com>
Change-Id: Iab5b0ae09bdd8b9c720c29168dfdafc23a5dde0d
Reviewed-on: http://git.am.freescale.net:8181/24502
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Richard Schmitt <richard.schmitt@freescale.com>
|
|
Merge remote-tracking branch 't1024-linux/master'
|
|
- enable mixed mode of MPIC for deep sleep
- add deep sleep support for t1024
- add SDXC support for T1024QDS
- add TDM node in dts for Maxim DS26522 Riser card.
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Change-Id: I9cb45b4a02814a4f4cd0a320510361c424545d44
Reviewed-on: http://git.am.freescale.net:8181/21426
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
|
|
Signed-off-by: Qiu Wujie <B49553@freescale.com>
---
This patch will be merged into the previous patch as below.
URL: https://patchwork.kernel.org/patch/3976141/
Change-Id: I5c860dd5b58400aa25f9cce444ee8e94b4488cc4
Reviewed-on: http://git.am.freescale.net:8181/21965
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
|
|
Ls1021a-qds has the same ip block as esdhc on powerpc platform.
But they have diferent endian mode and different IO entry.
So we change the IO entry to generic IO to support working on
different architecture with different endian mode. Also add some
properties to support esdhc on ls1021a-qds.
Signed-off-by: Qiu WeiJie <B49553@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
---
This patch has sent to linux-mmc maillist.
URL: https://patchwork.kernel.org/patch/3976141/
Change-Id: I4959b07bf9e38a442316f0f45425018fa7d6f579
Reviewed-on: http://git.am.freescale.net:8181/14824
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
|
|
According to Spec 2.0, command complete interrupt will be generate
within 150 SD-CLK. But this was not long enough for T1040 board.
So add quirk SDHCI_QUIRK2_LONG_TIME_CMD_COMPLETE_IRQ
to enlarge this detect time to avoid hardware timeout error.
Signed-off-by: Wujie Qiu <B49553@freescale.com>
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Change-Id: Ia850b3fb707824c65f57511943ec0c91f78d9899
Reviewed-on: http://git.am.freescale.net:8181/13438
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Zhenhua Luo <zhenhua.luo@freescale.com>
Tested-by: Zhenhua Luo <zhenhua.luo@freescale.com>
|
|
In order to check whether the card has been removed, the function
mmc_send_status() will send command CMD13 to card and ask the card
to send its status register to sdhc driver, which will generate
many interrupts repeatedly and make the system performance bad.
From the performance test on Freescale's board (such as Iozone for SD),
the performance will degrade about 4~6%.
There is one another way to get this information,
which is to read the register PRSSTAT and check the bit CDPL or CINS.
If the card is present, these two bit will set to one.
Therefore, add callback function get_cd() to check whether
the card has been inserted/removed when the driver supports this feature.
If the card is present, 0 will return, if the card is absent, 1 will return.
If the controller will not support this feature, -ENOSYS will return.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Change-Id: I5ef39890637727c0120bea7497421b5ccd99f346
Reviewed-on: http://git.am.freescale.net:8181/12879
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Yang Li <LeoLi@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
Interrupt mode for t1040RDB is working. Enable it to
avoid redundant poling mode.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Change-Id: I686faa7c763758815f7c6146670ab4061a76a63d
Reviewed-on: http://git.am.freescale.net:8181/12830
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
|
|
According to Spec 2.0, command complete interrupt will be generate within
150 SD-CLK. But this was not long enough for P5040 board. So add quirk
SDHCI_QUIRK2_LONG_TIME_CMD_COMPLETE_IRQ to enlarge this detect time to avoid
hardware timeout error.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Change-Id: I26863bf687275191ead0e6396c381d9c15fb8e07
Reviewed-on: http://git.am.freescale.net:8181/12215
Reviewed-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
The timeout value got from eMMC card on T4240QDS is
incorrect. Disable trim and use erase instead.
Remove quirk SDHCI_QUIRK_BROKEN_ADMA to enable ADMA on
T4240QDS.
Calculate the timeout based SD clock when we have qurik
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Change-Id: I2eca7c1d00c89db8b2e257f60b6ef62971536f90
Reviewed-on: http://git.am.freescale.net:8181/11981
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
For removable card we avoid to invoke resume and suspend call back
function, because it's not safe in case card was removed and replaced
with a new one during suspend. But it's still need to judge the bus_ops
hook before we run it.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Change-Id: I1c2d26171a7ca02c2ecd2f029e37c5b715fb4105
Reviewed-on: http://git.am.freescale.net:8181/11804
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
This merges 3.12.15-rt25.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
drivers/misc/Makefile
drivers/net/ethernet/freescale/gianfar.c
drivers/net/ethernet/freescale/gianfar_ethtool.c
drivers/net/ethernet/freescale/gianfar_sysfs.c
|
|
On !RT interrupt runs with interrupts disabled. On RT it's in a
thread, so no need to disable interrupts at all.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
drivers/mmc/card/block.c
|
|
This reverts v3.13-rc3+ (78fd82238d0e5716) to v3.12, except for
commits which I noticed which appear relevant to the SDK.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Conflicts:
arch/powerpc/include/asm/kvm_host.h
arch/powerpc/kvm/book3s_hv_rmhandlers.S
arch/powerpc/kvm/book3s_interrupts.S
arch/powerpc/kvm/e500.c
arch/powerpc/kvm/e500mc.c
arch/powerpc/sysdev/fsl_soc.h
drivers/Kconfig
drivers/cpufreq/ppc-corenet-cpufreq.c
drivers/dma/fsldma.c
drivers/dma/s3c24xx-dma.c
drivers/misc/Makefile
drivers/mmc/host/sdhci-of-esdhc.c
drivers/mtd/devices/m25p80.c
drivers/net/ethernet/freescale/gianfar.h
drivers/platform/Kconfig
drivers/platform/Makefile
drivers/spi/spi-fsl-espi.c
include/crypto/algapi.h
include/linux/netdev_features.h
include/linux/skbuff.h
include/net/ip.h
net/core/ethtool.c
|
|
|
|
commit 945be38caa287b177b8c17ffaae7754cab6a658f upstream.
It is possible for chip->fixes to be null. Check before dereferencing it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 77a0122e0838663795651aa0beb2325156f98c09 upstream.
A host controller for a SD card may need a GPIO for card detect in order
to wake up from runtime suspend when a card is inserted. If that GPIO is
not configured, then the host controller will not wake up. Fix that for
the affected devices by not enabling runtime PM unless the GPIO is
successfully set up.
This affects BYT sd card host controller which had runtime PM enabled from
v3.11. For completeness, the MFD sd card host controller is flagged also.
The original patch before rebasing (see link below) was tested on v3.11.10
and v3.12.4 although the patch applied with some offsets and fuzz. The
original patch is here:
http://marc.info/?l=linux-mmc&m=138676702327057
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9288cac05405a7da406097a44721aa4004609b4d upstream.
This reverts and updates commit 77776fd0a4cc541b9 ("mmc: sd: fix the
maximum au_size for SD3.0"). The au_size for SD3.0 cannot be achieved
by a simple bit shift, so this needs to be implemented differently.
Also, don't print the warning in case of 0 since 'not defined' is
different from 'invalid'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 66b512eda74d59b17eac04c4da1b38d82059e6c9 upstream.
With some SDIO devices, timeout errors can happen when reading data.
To solve this issue, the DMA transfer has to be activated before sending
the command to the device. This order is incorrect in PDC mode. So we
have to take care if we are using DMA or PDC to know when to send the
MMC command.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f662ae48ae67dfd42739e65750274fe8de46240a upstream.
Under function mmc_blk_issue_rq, after an MMC discard operation,
the MMC request data structure may be freed in memory. Later in
the same function, the check of req->cmd_flags & MMC_REQ_SPECIAL_MASK
is dangerous and invalid. It causes the MMC host not to be released
when it should.
This patch fixes the issue by marking the special request down before
the discard/flush operation.
Reported by: Harold (SoonYeal) Yang <haroldsy@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
eSDHC host had bit eSDHC_IRQSTAT[3] to indicate that DMA (SDMA or ADMA)
transfer has failed. So enable this bit detecting and its interrupt.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Change-Id: If2abc2718d4bf0d020077848804a9ac59d5c2010
Reviewed-on: http://git.am.freescale.net:8181/5927
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
A-005055: A glitch is generated on the card clock
due to software reset or a clock change.
Impact list:
T4240-4160-R1.0 B4860-4420-R1.0-R2.0 P3041-R1.0-R1.1-R2.0
P2041-2040-R1.0-R1.1-R2.0 P1010-1014-R1.0 P5020-5010-R1.0-R2.0
P5040-5021-R1.0-R2.0-R2.1
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Change-Id: Idf4e1fd52ec4b5748cf9cbf86365a70c9952d1be
Reviewed-on: http://git.am.freescale.net:8181/5925
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
A-003980: SDHC: Glitch is generated on the card clock with software reset or
clock divider change
Description: A glitch may occur on the SDHC card clock when the software sets
the RSTA bit (software reset) in the system control register. It can also be
generated by setting the clock divider value. The glitch produced can cause
the external card to switch to an unknown state. The occurrence is not
deterministic.
Workaround:
A simple workaround is to disable the SD card clock before the software reset,
and enable it when the module resumes normal operation.
The Host and the SD card are in a master-slave relationship. The Host provides
clock and control transfer across the interface. Therefore, any existing
operation is discarded when the Host controller is reset.
The recommended flow is as follows:
1. Software disable bit[3], SDCLKEN, of the System Control Register
2. Trigger software reset and/or set clock divider
3. Check bit[3], SDSTB, of the Present State Register for stable clock
4. Enable bit[3], SDCLKEN, of the System Control Register
Using the above method, the eSDHC cannot send command or transfer data when
there is a glitch in the clock line, and the glitch does not cause any issue.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Change-Id: I43a6ef8fdffeeeb13bfef215825d417778ce0bf3
Reviewed-on: http://git.am.freescale.net:8181/5916
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
When Auto-CMD12 is enabled, Auto-cmd12 error status and signal
bit should be set to reflect this behaviour in case error.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Change-Id: Ief2ca5fad7861154c03cc1aa28e130f42d79e27b
Reviewed-on: http://git.am.freescale.net:8181/5928
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
Clock of esdhc host don't support clock disable and enbale.
So clock stable bit didn't behave as it mean. Just fix it
to '1' to avoid misreading.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Change-Id: Ib718005ca3419130a43cbf61c6351878b4eb4dbf
Reviewed-on: http://git.am.freescale.net:8181/5929
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
Vender version and sdhc spec version of T4240-R1.0-R2.0 is incorrect.
The right value should be VVN=0x13, SVN = 0x1. The wrong version number
will break down the ADMA data transfer. This defect only exist in
T4240-R1.0-R2.0.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Change-Id: I9fd43ec6d293b51d8928c28b4880c8f73704d946
Reviewed-on: http://git.am.freescale.net:8181/5923
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
As spec detailed:
Error Interrupt Status Register(Offset 032h)[15-12]
Error Interrupt Status Enable Register (Offset 036h)[15-12]
Error Interrupt Signal Enable Register (Offset 03Ah)[15-12]
Bits above are specified by vendor itself.
So add interface to handle this requirememt.
Also share sdhci_dma_show in sdhc.h for platform usr.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Change-Id: If1203dcaed81ad5180395c755d779cb70e4fbbe6
Reviewed-on: http://git.am.freescale.net:8181/5926
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
A-004388: eSDHC DMA might not stop if error occurs on system transaction
New models as 5040/5021 were added to this errata, and some tiny change
was applied into the workaround.
Signed-off-by: Haijun Zhang <haijun.zhang@freescale.com>
Change-Id: Id2e618b3dc69856e8c23a3ce46dc18bb2c07fded
Reviewed-on: http://git.am.freescale.net:8181/5924
Tested-by: Review Code-CDREVIEW <CDREVIEW@freescale.com>
Reviewed-by: Xiaobo Xie <X.Xie@freescale.com>
Reviewed-by: Jose Rivera <German.Rivera@freescale.com>
|
|
Conflicts:
Documentation/hwmon/ina2xx
arch/powerpc/Kconfig
arch/powerpc/boot/dts/b4860emu.dts
arch/powerpc/boot/dts/b4qds.dtsi
arch/powerpc/boot/dts/fsl/b4si-post.dtsi
arch/powerpc/boot/dts/fsl/qoriq-sec6.0-0.dtsi
arch/powerpc/boot/dts/p1023rdb.dts
arch/powerpc/boot/dts/t4240emu.dts
arch/powerpc/boot/dts/t4240qds.dts
arch/powerpc/configs/85xx/p1023_defconfig
arch/powerpc/configs/corenet32_smp_defconfig
arch/powerpc/configs/corenet64_smp_defconfig
arch/powerpc/configs/mpc85xx_smp_defconfig
arch/powerpc/include/asm/cputable.h
arch/powerpc/include/asm/device.h
arch/powerpc/include/asm/epapr_hcalls.h
arch/powerpc/include/asm/kvm_host.h
arch/powerpc/include/asm/mpic.h
arch/powerpc/include/asm/pci.h
arch/powerpc/include/asm/ppc-opcode.h
arch/powerpc/include/asm/ppc_asm.h
arch/powerpc/include/asm/reg_booke.h
arch/powerpc/kernel/epapr_paravirt.c
arch/powerpc/kernel/process.c
arch/powerpc/kernel/prom.c
arch/powerpc/kernel/setup-common.c
arch/powerpc/kernel/setup_32.c
arch/powerpc/kernel/setup_64.c
arch/powerpc/kernel/smp.c
arch/powerpc/kernel/swsusp_asm64.S
arch/powerpc/kernel/swsusp_booke.S
arch/powerpc/kvm/book3s_pr.c
arch/powerpc/kvm/booke.c
arch/powerpc/kvm/booke.h
arch/powerpc/kvm/e500.c
arch/powerpc/kvm/e500.h
arch/powerpc/kvm/e500_emulate.c
arch/powerpc/kvm/e500mc.c
arch/powerpc/kvm/powerpc.c
arch/powerpc/perf/e6500-pmu.c
arch/powerpc/platforms/85xx/Kconfig
arch/powerpc/platforms/85xx/Makefile
arch/powerpc/platforms/85xx/b4_qds.c
arch/powerpc/platforms/85xx/c293pcie.c
arch/powerpc/platforms/85xx/corenet_ds.c
arch/powerpc/platforms/85xx/corenet_ds.h
arch/powerpc/platforms/85xx/p1023_rds.c
arch/powerpc/platforms/85xx/p2041_rdb.c
arch/powerpc/platforms/85xx/p3041_ds.c
arch/powerpc/platforms/85xx/p4080_ds.c
arch/powerpc/platforms/85xx/p5020_ds.c
arch/powerpc/platforms/85xx/p5040_ds.c
arch/powerpc/platforms/85xx/smp.c
arch/powerpc/platforms/85xx/t4240_qds.c
arch/powerpc/platforms/Kconfig
arch/powerpc/sysdev/Makefile
arch/powerpc/sysdev/fsl_mpic_timer_wakeup.c
arch/powerpc/sysdev/fsl_msi.c
arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pci.h
arch/powerpc/sysdev/fsl_soc.h
arch/powerpc/sysdev/mpic.c
arch/powerpc/sysdev/mpic_timer.c
drivers/Kconfig
drivers/clk/Kconfig
drivers/clk/clk-ppc-corenet.c
drivers/cpufreq/Kconfig.powerpc
drivers/cpufreq/Makefile
drivers/cpufreq/ppc-corenet-cpufreq.c
drivers/crypto/caam/Kconfig
drivers/crypto/caam/Makefile
drivers/crypto/caam/ctrl.c
drivers/crypto/caam/desc_constr.h
drivers/crypto/caam/intern.h
drivers/crypto/caam/jr.c
drivers/crypto/caam/regs.h
drivers/dma/fsldma.c
drivers/hwmon/ina2xx.c
drivers/iommu/Kconfig
drivers/iommu/fsl_pamu.c
drivers/iommu/fsl_pamu.h
drivers/iommu/fsl_pamu_domain.c
drivers/iommu/fsl_pamu_domain.h
drivers/misc/Makefile
drivers/mmc/card/block.c
drivers/mmc/core/core.c
drivers/mmc/host/sdhci-esdhc.h
drivers/mmc/host/sdhci-pltfm.c
drivers/mtd/nand/fsl_ifc_nand.c
drivers/net/ethernet/freescale/gianfar.c
drivers/net/ethernet/freescale/gianfar.h
drivers/net/ethernet/freescale/gianfar_ethtool.c
drivers/net/phy/at803x.c
drivers/net/phy/phy_device.c
drivers/net/phy/vitesse.c
drivers/pci/msi.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/uio/Kconfig
drivers/uio/Makefile
drivers/uio/uio.c
drivers/usb/host/ehci-fsl.c
drivers/vfio/Kconfig
drivers/vfio/Makefile
include/crypto/algapi.h
include/linux/iommu.h
include/linux/mmc/sdhci.h
include/linux/msi.h
include/linux/netdev_features.h
include/linux/phy.h
include/linux/skbuff.h
include/net/ip.h
include/uapi/linux/vfio.h
net/core/ethtool.c
net/ipv4/route.c
net/ipv6/route.c
|
|
commit fbd986cd420d1deeabf1039ec4e74075a5639db5 upstream.
In some cases, a NULL pointer dereference happens because data is NULL when
STATE_END_REQUEST case is reached in atmci_tasklet_func.
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c1fa3426aa5c782724c97394303d52228206eda4 upstream.
When a software timeout occurs, the transfer is not stopped. In DMA case,
it causes DMA channel to be stuck because the transfer is still active
causing following transfers to be queued but not computed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reported-by: Alexander Morozov <etesial@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some features can be configured by the companion I2C chips,
which may not be available at the probe time. Fix the issue
by returning -EPROBE_DEFER when the MMC controller slots
are not configured.
While at it, let's also add minimal device tree support so
omap24xx platforms can use this driver without legacy mode
since we claim to support device tree for mach-omap2 based
systems.
Although adding the minimal device tree support is not strictly
a fix, it does remove one of the last blockers for dropping a
bunch of legacy platform data for mach-omap2.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We are wrongly relying on device id for the DMA configuration
which can lead to wrong DMA channel being selected.
Fix the issue by using the standard resources like we should.
Cc: linux-mmc@vger.kernel.org
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
|
|
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
|
|
Pull ARM updates from Russell King:
"Included in this series are:
1. BE8 (modern big endian) changes for ARM from Ben Dooks
2. big.Little support from Nicolas Pitre and Dave Martin
3. support for LPAE systems with all system memory above 4GB
4. Perf updates from Will Deacon
5. Additional prefetching and other performance improvements from Will.
6. Neon-optimised AES implementation fro Ard.
7. A number of smaller fixes scattered around the place.
There is a rather horrid merge conflict in tools/perf - I was never
notified of the conflict because it originally occurred between Will's
tree and other stuff. Consequently I have a resolution which Will
forwarded me, which I'll forward on immediately after sending this
mail.
The other notable thing is I'm expecting some build breakage in the
crypto stuff on ARM only with Ard's AES patches. These were merged
into a stable git branch which others had already pulled, so there's
little I can do about this. The problem is caused because these
patches have a dependency on some code in the crypto git tree - I
tried requesting a branch I can pull to resolve these, and all I got
each time from the crypto people was "we'll revert our patches then"
which would only make things worse since I still don't have the
dependent patches. I've no idea what's going on there or how to
resolve that, and since I can't split these patches from the rest of
this pull request, I'm rather stuck with pushing this as-is or
reverting Ard's patches.
Since it should "come out in the wash" I've left them in - the only
build problems they seem to cause at the moment are with randconfigs,
and since it's a new feature anyway. However, if by -rc1 the
dependencies aren't in, I think it'd be best to revert Ard's patches"
I resolved the perf conflict roughly as per the patch sent by Russell,
but there may be some differences. Any errors are likely mine. Let's
see how the crypto issues work out..
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (110 commits)
ARM: 7868/1: arm/arm64: remove atomic_clear_mask() in "include/asm/atomic.h"
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: 7871/1: amba: Extend number of IRQS
ARM: 7887/1: Don't smp_cross_call() on UP devices in arch_irq_work_raise()
ARM: 7872/1: Support arch_irq_work_raise() via self IPIs
ARM: 7880/1: Clear the IT state independent of the Thumb-2 mode
ARM: 7878/1: nommu: Implement dummy early_paging_init()
ARM: 7876/1: clear Thumb-2 IT state on exception handling
ARM: 7874/2: bL_switcher: Remove cpu_hotplug_driver_{lock,unlock}()
ARM: footbridge: fix build warnings for netwinder
ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu
ARM: fix misplaced arch_virt_to_idmap()
ARM: 7848/1: mcpm: Implement cpu_kill() to synchronise on powerdown
ARM: 7847/1: mcpm: Factor out logical-to-physical CPU translation
ARM: 7869/1: remove unused XSCALE_PMU Kconfig param
ARM: 7864/1: Handle 64-bit memory in case of 32-bit phys_addr_t
ARM: 7863/1: Let arm_add_memory() always use 64-bit arguments
ARM: 7862/1: pcpu: replace __get_cpu_var_uses
ARM: 7861/1: cacheflush: consolidate single-CPU ARMv7 cache disabling code
...
|
|
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
|