| Age | Commit message (Collapse) | Author |
|---|
|
Tested on OLPC XO-4/MMP3, where the card detection pin for one of
the controllers is a sideband GPIO. The third cell in the cd-gpios
property controls whether the GPIO is active high/active low.
(Also, pass host_caps2 through from platdata to the mmc host.)
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
[kliu5@marvell.com: Compile fix]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This part of the tty tree (unfortunately with all the preceding patches
as well) is a dependency for some of the OMAP cleanups, so we've pulled
it in as a dependency based on agreement with Greg.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Remove the ancient omap specific atags that are no longer needed.
At some point we were planning to pass the bootloader information
with custom atags that did not work out too well.
There's no need for these any longer as the kernel has been booting
fine without them for quite some time. And Now we have device tree
support that can be used instead.
* tag 'cleanup-omap-tags-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: remove plat/board.h file
ARM: OMAP: move debug_card_init() function
ARM: OMAP1: move lcd pdata out of arch/arm/*
ARM: OMAP1: move omap1_bl pdata out of arch/arm/*
ARM: OMAP: remove the omap custom tags
ARM: OMAP1: remove the crystal type tag parsing
ARM: OMAP: remove the sti console workaround
ARM: OMAP: omap3evm: cleanup revision bits
ARM: OMAP: cleanup struct omap_board_config_kernel
+ sync to 3.6-rc5
|
|
This pulls in the fixes in 3.6-rc6
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This the definitions for the tegra sdhci driver out of
the tegra include directories, which is the last one
for this platform.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Chris Ball <cjb@laptop.org>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the pxa include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Paul Parsons <lost.distance@yahoo.com>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Acked-By: Stefan Schmidt <stefan@openezx.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Harald Welte <laforge@openezx.org>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Tomas Cech <sleep_walker@suse.cz>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: openezx-devel@lists.openezx.org
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the msm include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-arm-msm@vger.kernel.org
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
|
|
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the davinci include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
|
|
next/fixes-non-critical
From "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad72 now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
mmc_gpio_request_ro() doesn't store the requested gpio in ctx->ro_gpio.
As a result, subsequent calls to mmc_gpio_get_ro() will always fail
with -ENOSYS because the gpio number isn't available to that function.
Cc: stable <stable@vger.kernel.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_probe':
drivers/mmc/host/omap_hsmmc.c:1808: warning: initialization discards qualifiers from pointer target type
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
|
|
plat/board.h file is now empty - remove it.
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: linux-mmc@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Nothing from this file is needed, so remove the include. This helps
single zImage work by reducing use of the mach-tegra/include/mach/
directory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org>
|
|
module_pci_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
module_pci_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
module_pci_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
module_spi_driver makes the code simpler by eliminating
module_init and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch fixes the checkpatch error and warnings listed below:
ERROR: return is not a function, parentheses are not required
WARNING: Prefer pr_err(... to printk(KERN_ERR, ...
WARNING: quoted string split across lines
WARNING: line over 80 characters
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
If MMC_CAP_NONREMOVABLE is set, only issue a detect job on init.
Signed-off-by: Johan Rudholm <johan.rudholm@stericsson.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Fixed the below message.
WARNING: drivers/mmc/host/built-in.o(.text+0x5ee8): Section mismatch in reference from the function dw_mci_probe() to the function .init.text:dw_mci_init_slot()
The function dw_mci_probe() references
the function __init dw_mci_init_slot().
This is often because dw_mci_probe lacks a __init
annotation or the annotation of dw_mci_init_slot is wrong
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
When compiling a kernel that supports only Tegra30 and not Tegra20,
the SDHCI driver will fail to compile since the of_match_device() failure
fallback code unconditinally references soc_data_tegra20, which is only
compiled in when Tegra20 support is enabled.
In Kernel 3.7, both Tegra20 and Tegra30 will only support booting using
device tree, Hence, there is never a need to fall back to using
soc_data_tegra20 if of_mach_device() fails. Instead, make this case an
error. This removes the reference to soc_data_tegra20, and hence solves
the compile failure.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Consolidate the duplicated code around the handling of CMD_TIMEOUT,
CMD_CRC, DATA_TIMEOUT, DATA_CRC and CARD_ERR handling into a single
function.
This generally shrinks code bloat, but is also required for implementing
software based guard timers.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Flushing spurious IRQs from HSMMC IP is done twice in omap_hsmmc_irq
and omap_hsmmc_do_irq. Consolidate them to one location.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
SYSCONFIG register of HSMMC IP is managed by the omap hwmod
abstraction layer. Resetting the IP and configuring the correct
SYSCONFIG mode is centrally managed by hwmod.
Remove code which manipulates IP reset and SYSCONFIG directly in
the driver.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Some straight forward cleanup of unnecessary #include's and host
variables. Some of the verbose and redundant debug messages are
converted to use dev_vdbg.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The function mmc_omap_report_irq uses raw printks and the actual output
was disabled by a static variable. Make the function use dev_vdbg macro
and use it under the standard CONFIG_MMC_DEBUG flag.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Get rid of some unnecessary includes in the driver and
a few unused variables.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
ext_csd exported through debugfs is printed in reverse order (from
byte 511 to 0), which causes confusion.
Fix the for loop to print ext_csd in natural order.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
HPI can be issued only in programming state to bring the card to
transfer state. If the card is already in transfer state, doing
a HPI is redundant.
Fix this by adding transfer state to the list of exceptions to
doing HPI and return without error.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Without reset, SD controller may stay in disable mode, SD card can't
be detected when resume from power saving mode.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
mmc core suspend and resume functions had already called sdh_set_ios
with proper flags.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In BF60x RSI controller:
1) MMR read/write width differs.
2) PWR and CTL MMRs are merged to together.
3) ROD and PD_DAT3 bit masks are obsolete.
4) New RSI block size MMR is defined.
5) The definition of DMA descriptor set size is changed.
6) set_ios should powers up controller in 2 steps.
In addition, this patch cleans up the spin locks.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
bf518 RSI dma doesn't work in array mode.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
1/ If regulator_get fails, return an error. This is important if
it failed with EPROBE_DEFER, as the probe needs to be deferred.
2/ Don't set .set_power until the regulator has been found, or
the deferred probe will not bother calling omap_hsmmc_reg_get().
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Add missing usb_free_urb on failure path after usb_alloc_urb.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@km exists@
local idexpression e;
expression e1,e2,e3;
type T,T1;
identifier f;
@@
* e = usb_alloc_urb(...)
... when any
when != e = e1
when != e1 = (T)e
when != e1(...,(T)e,...)
when != &e->f
if(...) { ... when != e2(...,(T1)e,...)
when != e3 = e
when forall
(
return <+...e...+>;
|
* return ...;
) }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
This patch adds device tree support and binding documentation for
sdhci-dove.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Prepare the clock before enabling it.
Signed-off-by: Chao Xie <xiechao.mail@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The vmmc regulator should not rely on the platform code to enable it.
Expliciitly enable and disable the regulator inside the driver.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
On some systems the host controller does not support vccq
signaling. This is supplied by a dedicated regulator (vqmmc).
Add support for this regulator.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The register of eSDHC Host Controller Capabilities is not compatible with
standard SDHC register, and eSDHC cannot support End Attribute in NOP ADMA
descriptor. With this patch eSDHC can works in ADMA mode and performance
can be improved.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Pan Jiafei <Jiafei.Pan@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
After commit 26b88520b80695a6fa5fd95b5d97c03f4daf87e0 ("mmc:
omap_hsmmc: remove private DMA API implementation"), the Nokia N800
here stopped booting:
[ 2.086181] Waiting for root device /dev/mmcblk0p1...
[ 2.324066] Unhandled fault: imprecise external abort (0x406) at 0x00000000
[ 2.331451] Internal error: : 406 [#1] ARM
[ 2.335784] Modules linked in:
[ 2.339050] CPU: 0 Not tainted (3.6.0-rc3 #60)
[ 2.344146] PC is at default_idle+0x28/0x30
[ 2.348602] LR is at trace_hardirqs_on_caller+0x15c/0x1b0
...
This turned out to be due to memory corruption caused by long-broken
PIO code in drivers/mmc/host/omap.c. (Previously, this driver had
been using DMA; but the above commit caused the MMC driver to fall
back to PIO mode with an unmodified Kconfig.)
The PIO code, added with the rest of the driver in commit
730c9b7e6630f786fcec026fb11d2e6f2c90fdcb ("[MMC] Add OMAP MMC host
driver"), confused bytes with 16-bit words. This bug caused memory
located after the PIO transfer buffer to be corrupted with transfers
larger than 32 bytes. The driver also did not increment the buffer
pointer after the transfer occurred. This bug resulted in data
corruption during any transfer larger than 64 bytes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
For several MoviNAND eMMC parts, there are known issues with secure
erase and secure trim. For these specific MoviNAND devices, we skip
these operations.
Specifically, there is a bug in the eMMC firmware that causes
unrecoverable corruption when the MMC is erased with MMC_CAP_ERASE
enabled.
References:
http://forum.xda-developers.com/showthread.php?t=1644364
https://plus.google.com/111398485184813224730/posts/21pTYfTsCkB#111398485184813224730/posts/21pTYfTsCkB
Signed-off-by: Ian Chen <ian.cy.chen@samsung.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable <stable@vger.kernel.org> [3.0+]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
The documentation for the dw_mmc part says that the low power
mode should normally only be set for MMC and SD memory and should
be turned off for SDIO cards that need interrupts detected.
The best place I could find to do this is when the SDIO interrupt
was first enabled. I rely on the fact that dw_mci_setup_bus()
will be called when it's time to reenable.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Data transfer will be continued until all the bytes are transmitted,
even if data crc error occurs during a multiple-block data transfer.
This means RXDR/TXDR interrupts will occurs until data transfer is
terminated. Early setting of host->sg to NULL prevents going into
xxx_data_pio functions, hence permanent unhandled RXDR/TXDR interrupts
occurs. And checking error interrupt status in the xxx_data_pio functions
is no need because dw_mci_interrupt does do the same. This patch also
removes it.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Datasheet of SYNOPSYS mentions that DTO(Data Transfer Over) interrupt
will be raised even if some error interrupts, however it is actually
found that DTO does not occur. SYNOPSYS has confirmed this issue.
Current implementation defers the call of tasklet_schedule until DTO
when the error interrupts is happened. This patch fixes error handling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
RINTSTS status includes masked interrupts as well as unmasked.
data_status and cmd_status are set by value of RINTSTS in interrupt handler
and tasklet finally uses it to decide whether error is happened or not.
In addition, MINTSTS status is used for setting data_status in PIO.
Masked error interrupt will not be handled and that status can be considered
non-error case.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed By: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.
Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.5, 3.6]
Signed-off-by: Chris Ball <cjb@laptop.org>
|
