| Age | Commit message (Collapse) | Author |
|---|
|
Add skb->rxhash support for TCP packets only because the bnx2 RSS hash
does not hash UDP ports.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dump the correct MCP registers and add EMAC_RX_STATUS register during
NETDEV_WATCHDOG for debugging.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add prefetches of the skb and the next rx descriptor to speed up rx path.
Use prefetchw() for the skb [suggested by Eric Dumazet].
The rx descriptor is in skb->data which is mapped for streaming mode DMA.
Eric Dumazet pointed out that we should not prefetch the data before
dma_sync. So we prefetch only if dma_sync is no_op on the system.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DMA API is preferred.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current water marks are too high and can cause unnecessary flow
control frames.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MTU changes, ring size changes, etc cause the chip to be reset and the
statisctics flushed. To keep track of the accumulated statistics, we
add code to save the whole statistics block before reset. We also
modify the macros and statistics functions to return the sum of the
saved and current counters.
Based on original patch by Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To help debug the problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to the fact that skb_dma_map/unmap do not work correctly when a HW
IOMMU is enabled it has been recommended to go about removing the calls
from the network device drivers.
[ Fix bnx2_free_tx_skbs() ring indexing and use NETDEV_TX_OK return
code in bnx2_start_xmit() after cleaning up DMA mapping errors. -Mchan ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BNX2_L2CTX_STATUSB_NUM definition needs to be changed to match
the recent firmware update:
commit 078b0735881c7969aaf21469f3577831cddd9f8c
bnx2: Update firmware to 5.0.0.j3.
Without the fix, bnx2 can crash intermittently in bnx2_rx_int() when
iSCSI is enabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/yellowfin.c
|
|
The structure, once initialized, never changes.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add flag to expand the workaround to both chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The slow path calls to the cnic driver are sleepable calls so we
cannot use rcu_read_lock(). Use mutex for these slow path calls
instead.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
Documentation/feature-removal-schedule.txt
drivers/scsi/fcoe/fcoe.c
net/core/drop_monitor.c
net/core/net-traces.c
|
|
Add interface and functions to support a new CNIC driver to drive
the Broadcom bnx2 hardware for iSCSI offload.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
When using bnx2 in a high transmit load, bnx2_tx_int() cost is pretty high.
There are two reasons.
One is an expensive call to bnx2_get_hw_tx_cons(bnapi) for each freed skb
One is cpu stalls when accessing skb_is_gso(skb) / skb_shinfo(skb)->nr_frags
because of two cache line misses.
(One to get skb->end/head to compute skb_shinfo(skb),
one to get is_gso/nr_frags)
This patch :
1) avoids calling bnx2_get_hw_tx_cons(bnapi) too many times.
2) makes bnx2_start_xmit() cache is_gso & nr_frags into sw_tx_bd descriptor.
This uses a litle bit more ram (256 longs per device on x86), but helps a lot.
3) uses a prefetch(&skb->end) to speedup dev_kfree_skb(), bringing
cache line that will be needed in skb_release_data()
result is 5 % bandwidth increase in benchmarks, involving UDP or TCP receive
& transmits, when a cpu is dedicated to ksoftirqd for bnx2.
bnx2_tx_int going from 3.33 % cpu to 0.5 % cpu in oprofile
Note : skb_dma_unmap() still very expensive but this is for another patch,
not related to bnx2 (2.9 % of cpu, while it does nothing on x86_32)
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on original patch by Ben Hutchings <ben@decadent.org.uk> and
Bastian Blank <waldi@debian.org>, with the following main changes:
Separated the mips firmware and rv2p firmware into different files
to make it easier to update them separately.
Added some code to fixup the rv2p code with run-time information
such as PAGE_SIZE.
Update version to 2.0.0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
They are provided generically by linux/mii.h now.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change MSI-X vector names to "ethx-%d".
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-sta.c
|
|
The bnx2 chips do not support per MSI vector masking. On 5706/5708, new MSI
address/data are stored only when the MSI enable bit is toggled. As a result,
SMP affinity no longer works in the latest kernel. A more serious problem is
that the driver will no longer receive interrupts when the MSI receiving CPU
goes offline.
The workaround in this patch only addresses the problem of CPU going offline.
When that happens, the driver's timer function will detect that it is making
no forward progress on pending interrupt events and will recover from it.
Eric Dumazet reported the problem.
We also found that if an interrupt is internally asserted while MSI and INTA
are disabled, the chip will end up in the same state after MSI is re-enabled.
The same workaround is needed for this problem.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Tested-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move all related timeout constants to the same location. BNX2
prefix is also added to make them more consistent.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default rx buffer water marks for XOFF/XON are for 1500 MTU. At
larger MTUs, these water marks need to be adjusted for effective
flow control.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before, the driver would not care about the return codes from pci_map_*
functions. This could be potentially dangerous if a mapping failed.
Now, we will check all pci_map_* calls. On the transmit side, we switch
to use the new function skb_dma_map(). On the receive side, we add
pci_dma_mapping_error().
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/ath9k/core.c
drivers/net/wireless/ath9k/main.c
net/core/dev.c
|
|
The bnx2 driver stores/uses the irq value from the pci_dev internally.
But when it stores the irq value, it has been performing an
integer demotion. Because of the recent changes made to
arch/x86/kernel/io_apic.c, the new method in creating the irq value
(using build_irq_for_pci_dev()) has exposed this bug on x86 systems.
Because of this demotion when calling request_irq() from
bnx2_request_irq(), the driver would get a return code of -EINVAL.
This is because the kernel could not find the requested irq descriptor.
By storing the irq value properly, the kernel can find the correct
irq descriptor and the bnx2 driver can operate normally.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The timer_interval field is only assigned once, and never reassigned.
We can safely replace all instances of the timer_interval with a
constant value.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The name of the board is only used during the initialization of
the adapter. We can save the space of a pointer by not storing
this information.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for configuring secondary unicast addresses. There
are 4 additional perfect match filters which can be used for
secondary unicast address support.
* Modified bnx2_set_mac_addr() to be more generic in handling
the setting of the perfect match filters
* Changed bnx2_set_rx_mode() to handle the unicast dev_addr_list
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Negotiate with boot code and ASF firmware to see if it can
support keeping VLAN tags in the RX packets. If supported
by firmware, the VLAN tag will be kept in the RX packet
unless VLAN acceleration is registered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable multiple rx rings if MSI-X vectors are available. We enable
up to 7 rx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add hw_tx_cons_ptr and hw_rx_cons_ptr to speed up the retreival of
the tx and rx consumer index, since the MSI-X and default status
blocks have different structures.
Combine status_blk and status_blk_msix into a union. We'll only use
one type of status block for each vector.
Separate the code to detect more rx and tx work from the code to
detect link related work.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for multi-ring support, rx ring variables are now put
in a separate bnx2_rx_ring_info struct. With MSI-X, we can support
multiple rx rings.
The functions to allocate/free rx memory and to initialize rx rings
are now modified to handle multiple rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for multi-ring support, tx ring variables are now put
in a separate bnx2_tx_ring_info struct. Multi tx ring will not be
enabled until it is fully supported by the stack. Only 1 tx ring
will be used at the moment.
The functions to allocate/free tx memory and to initialize tx rings
are now modified to handle multiple rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/smc911x.c
|
|
If the RTNL is held when we invoke flush_scheduled_work() we could
deadlock. One such case is linkwatch, it is a work struct which tries
to grab the RTNL semaphore.
The most common case are net driver ->stop() methods. The
simplest conversion is to instead use cancel_{delayed_}work_sync()
explicitly on the various work struct the driver uses.
This is an OK transformation because these work structs are doing
things like resetting the chip, restarting link negotiation, and so
forth. And if we're bringing down the device, we're about to turn the
chip off and reset it anways. So if we cancel a pending work event,
that's fine here.
Some drivers were working around this deadlock by using a msleep()
polling loop of some sort, and those cases are converted to instead
use cancel_{delayed_}work_sync() as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make the bnx2 code more consistent, all instances of
RX_COPY_THRESH have been changed to BNX2_RX_COPY_THRESH.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx_offset field is set to a constant value and initialized
only once. By replacing all references to the rx_offset field,
we can eliminate rx_offset from the bnx2 structure. This will
save 4 bytes for every bnx2 instance.
[Added parentheses to the definition of BNX2_RX_OFFSET, as noted
by Ben Hutchings.]
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because of some board issues, we need to disable parallel detect on
an HP blade. Without this patch, the link state can become stuck
when it goes into parallel detect mode.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the programmable high/low water marks in 5709 for
802.3 flow control.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CTX_WR macro is unnecessary and obfuscates the code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The REG_WR_IND/REG_RD_IND macros are unnecessary and obfuscate the
code. Many callers to these macros read and write shared memory from
the bp->shmem_base, so we add 2 similar functions that automatically
add the shared memory base.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the tx coalescing setup code independent of the MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Correct the MII expansion serdes control register definition.
2. Check an additional RUDI_INVALID bit when determining 5706S link.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Prefix "bp->phy_flags" names with BNX2_PHY_FLAG_* for consistency.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prefix "bnx2->flags" names with BNX2_* for consistency.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
