| Age | Commit message (Collapse) | Author |
|---|
|
Check next packet availability by validating that HW has finished CQE
placement. This saves latency of another dma transaction performed to update
SB indexes.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the previous unload flow, probed devices will reset the chip
in order to clean the remains of the UNDI driver.
As a result, it's possible for the FW to toggle the link.
This toggling can prove fatal, as long periods without link can cause the
filesystem mount to fail as the storage protocol timeouts. This has been
observed against particular switches with long link re-establishment time.
This patch informs FW during the reset period that the link should not
be toggled - the FW will keep it alive until some interface will load and claim
the link as its own.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update appropriate HSI files and adapt driver accordingly.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configure SFP+ tap values to optimize link signal according to NVRAM setup.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove most of the sparse warnings in the bnx2x compilation
(i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__').
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is now possible to enable dropless flow control via nvram.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If configured for PFC/ETS by management, configure chip regardless of the
presence of a remote peer which supports DCBX.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When drivers works on top of an old bootcode, it is theoretically subjected to
MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence,
rather than per CL45 command. On rare cases an old bootcodes may change that in
the middle, so to address that, the MDIO clock is set for each CL45 access.
In addition, setting the MDIO clock is now done per EMAC base, and
not per port number, since a specific port can potentially use both EMACs for
different PHY accesses.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case Link Flap Avoidance feature is supported by the MCP, bnx2x will enable
it, and will pass the appropriate parameter when load request is sent to
the MCP.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the driver-FW HSI to support changes to the 'update' ramrod
(FW supports this change since 7.8.2). This ramrod is sent when the cnic module
registers bnx2x, to enable changing the nic_mode configuration in HW at
run-time.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the bnx2x and cnic drivers into using FW 7.8.2
which was recently submitted into the linux-firmware tree.
A short summary of minor bugs fixed by this FW:
1. In switch dependent mode, fix several issues regarding inner vlan
vs. DCB priorities.
2. iSCSI - not all packets were completed on a forward channel.
3. DCB - fixed for 4-port devices.
4. Fixed false parity reported in CAM memories when operating near -5%
on the 1.0V core supply.
5. ETS default settings are set to fairness between traffic classes
(rather than strict priority), and uses the same chip receive buffer
configuration for both PFC and pause.
For a complete list of fixes made by this FW, see commit 236367db
in the linux-firmware git repository.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change various flows in the bnx2x driver which up until now flapped
the link - these flows now benefit from the link flap avoidance mechanism.
This includes the removal of the link reset made upon nic init, as it is
possible the link is already active at that time.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Various flows in the bnx2x driver cause a link-flap - if the link
is up, it would be toggled down (after a mac/phy reset) and then
taken back up.
In many of these cases, there is no need to do cause such a flap,
as the associated flows should not actually affect the link.
This patch adds the 'Link Flap Avoidance' mechanism, which allows
the driver to better determine if a given flow requires a link change,
and thus minimize the number of link flaps caused by the driver.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
advertisement
1. When FCoE offload driver is registered, copy its capabilities to the chip
scratchpad.
2. Copy FCoE/iSCSI MAC addresses in aligned manner to chip scratchpad.
3. Add FCoE/iSCSI statistics collection support
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds the ability to identify sfp+ modules' Tx fault, and when such
occur shut down the link.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In multi-function device, allow configuring dcbx admin params from all drivers
on a single physical port.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds energy efficient energy support (802.3az) to bnx2x
boards with 84833 phys (and sufficiently new BC and external FW).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following patch adds afex multifunction support to the driver (afex
multifunction is based on vntag header) and updates FW version used to 7.2.51.
Support includes the following:
1. Configure vif parameters in firmware (default vlan, vif id, default
priority, allowed priorities) according to values received from NIC.
2. Configure FW to strip/add default vlan according to afex vlan mode.
3. Notify link up to OS only after vif is fully initialized.
4. Support vif list set/get requests and configure FW accordingly.
5. Supply afex statistics upon request from NIC.
6. Special handling to L2 interface in case of FCoE vif.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The congestion management code has migrated into a common location,
allowing all fw writes controlling mf congestion to be made in a
single function in the code. This is a semantic change.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flow in which the bnx2x driver starts after a previous driver
has been terminated in an 'unclean' manner has several bugs and
FW risks, which makes it possible for the driver to fail after
boot-from-SAN or kdump.
This patch contains a revised flow which performs a safer
initialization, solving the possible crash scenarios.
Notice this patch contains lines with over 80 characters, as it
keeps print-strings in a single line.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new error flags are supported by the bnx2x FW.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch integrates FW 7.2.16 HSI and implements driver
part of GRO flow.
FW 7.2.16 adds the ability to aggregate packets for GRO
(and not just LRO) and also fixes some bugs.
1. Added new aggregation mode: GRO. In this mode packets are aggregated
such that the original packets can be reconstructed by the OS.
2. 57712 HW bug workaround - initialized all CAM TM registers to 0x32.
3. Adding the FCoE statistics structures to the BNX2X HSI.
4. Wrong configuration of TX HW input buffer size may cause theoretical
performance effect. Performed configuration fix.
5. FCOE - Arrival of packets beyond task IO size can lead to crash.
Fix firmware data-in flow.
6. iSCSI - In rare cases of on-chip termination the graceful termination
timer hangs, and the termination doesn't complete. Firmware fix to MSL
timer tolerance.
7. iSCSI - Chip hangs when target sends FIN out-of-order or with isles
open at the initiator side. Firmware implementation corrected to drop
FIN received out-of-order or with isles still open.
8. iSCSI - Chip hangs when in case of retransmission not aligned to 4-bytes
from the beginning of iSCSI PDU. Firmware implementation corrected
to support arbitrary aligned retransmissions.
9. iSCSI - Arrival of target-initiated NOP-IN during intense ISCSI traffic
might lead to crash. Firmware fix to relevant flow.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to send driver capabilities, settings and statistics to
management firmware.
[ Redone using many local variables, removed many unnecessary inlines,
and put #defines at the left margin suggested by Joe Perches ]
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add FCoE statistics support for FCoE capable devices.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Priority flow control counters for ethtool -S.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FW includes the following fixes:
1. (iSCSI) Arrival of un-solicited ASYNC message causes
firmware to abort the connection with RST.
2. (FCoE) There is a probability that truncated FCoE packet on
RX path won't get detected which might lead to FW assert.
3. (iSCSI) Arrival of target-initiated NOP-IN during intense
ISCSI traffic might lead to FW assert.
4. (iSCSI) Chip hangs when in case of retransmission not aligned
to 4-bytes from the beginning of iSCSI PDU.
5. (FCoE) Arrival of packets beyond task IO size can lead to crash.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM54616 PHY is very similar to the 54618SE, only without EEE support, which will not be activated due to querying the actual PHY type.
This check is already done by reading a dedicated PHY register.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
