Age | Commit message (Collapse) | Author |
|
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MDIO controller on the Frame Manager (Fman) is compatible with the
QE and Gianfar MDIO controllers, but we don't care about the TBI because
the Ethernet drivers (FMD) take care of programming it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take advantage of the new mdiobus_alloc_size() function to combine three
different memory allocations into one. This also simplies the error
handling.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the device tree probe function more data-driven, so that it no longer
searches the 'compatible' property more than once. The of_device_id[] array
allows for per-entry private data, so we use that to store details about each
type of node that the driver supports. This removes the need to check the
'compatible' property inside the probe function.
The driver supports four types on MDIO devices:
1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)
Gianfar, eTSEC2, and QE have different mappings for the TBIPA register, which
is needed to initialize the TBI PHY. In addition, the QE needs a special
hack because of the way the device tree is ordered.
All of this information is encapsulated in the fsl_pq_mdio_data structure,
so when an MDIO node is probed, per-device data and functions are used
to determine how to initialize the device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) Replace printk with dev_err
2) Fix some whitespace mistakes
3) Rename "ofdev" to "pdev", since it's a platform_device now
4) Fix an inadvertent compound statement by replacing commas with semicolons
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few small functions were called only by other functions in the same
file, so merge them together. One function, for example, was calculating
the device address even though the caller was doing the same thing.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove several unnecessary #include statements.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
None of the functions in fsl_pq_mdio.c are used by any other source file,
so there's no point in exporting them. Merge the header file into the
source file, make all the functions static, remove any EXPORT_SYMBOL
statements, and delete any #include "fsl_pq_mdio.h" statements.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Macro spin_event_timeout() was designed for simple polling of hardware
registers with a timeout, so use it when we poll the MIIMIND register.
This allows us to return an error code instead of polling indefinitely.
Note that PHY_INIT_TIMEOUT is a count of loop iterations, so we can't use
it for spin_event_timeout(), which asks for microseconds.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/freescale/fsl_pq_mdio.c
net/batman-adv/translation-table.c
net/ipv6/route.c
|
|
The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.
Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts the drivers in drivers/net/ethernet/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 952c5ca1 (fsl_pq_mdio: Clean up tbi address configuration) .probe returns
-EBUSY when the "tbi-phy" node is missing. Fix this.
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.
Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|