| Age | Commit message (Collapse) | Author |
|---|
|
Self explanitory dma_mapping_error addition to the 8139 driver, based on this:
https://bugzilla.redhat.com/show_bug.cgi?id=947250
It showed several backtraces arising for dma_map_* usage without checking the
return code on the mapping. Add the check and abort the rx/tx operation if its
failed. Untested as I have no hardware and the reporter has wandered off, but
seems pretty straightforward.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The work queue is initialised in rtl_open (when the interface goes up),
but canceled in rtl_remove_one (when the PCI device gets removed). If
the network interface is not brought up, then the work queue struct is
not initialised. When the device is removed, the attempt to cancel the
uninitialised work queue causes a lockdep warning.
This patch fixes the issue by moving cancel_work_sync to rtl_close (to
match rtl_open). (Note that rtl_close is also called via
unregister_netdev in rtl_remove_one.)
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new chip for RTL8411 series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cures transmit timeout's with DHCP observed
while running under KVM. When the transmit ring is cleaned out,
the Byte Queue Limit values need to be reset.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
8168evl offloaded checksums are wrong since commit
e5195c1f31f399289347e043d6abf3ffa80f0005 ("r8169: fix 8168evl frame padding.")
pads small packets to 60 bytes (without ethernet checksum). Typical symptoms
appear as UDP checksums which are wrong by the count of added bytes.
It isn't worth compensating. Let the driver checksum.
Due to the skb length changes, TSO code is moved before the Tx descriptor gets
written.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Holger Hoffstätte <holger.hoffstaette@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new chip for RTL8106E series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The suggestion as following:
- initial settings or default settings
- rtl_hw_start_xxx. rtl_hw_start_xxx may change some default settings.
- enable tx/rx. This has to be after the above two steps.
- rtl_set_rx_mode. AcceptXXXs have to be enabled after enabling tx/rx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new chip for RTL8111G series.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- replace rtl8168g-1.fw with rtl8168g-2.fw which support new method.
- fix PHY power down is useless.
- disable rx early which causes the rx abnormal.
- enable auto fifo.
- set 10M IFG to default value.
- fix the conflict between jumbo frame and flow control.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove useless action PHY_READ_EFUSE, PHY_READ_MAC_BYTE, PHY_WRITE_MAC_BYTE,
PHY_WRITE_ERI_WORD. And define the new action PHY_MDIO_CHG.
PHY_MDIO_CHG is used to modify the mdio operation. By the way, the
firmware could support setting mac ocp.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the new settings and correct the wrong settings.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the current settings with rtl_writephy and rtl_readphy.
For the hardware, the settings are same with previous ones. This
make the setting method like the previous chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some codes are belong to binary codes and should be removed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It would cause no link after suspending or shutdowning when the
nic changes the speed to 10M and connects to a link partner which
forces the speed to 100M.
Check the link partner ability to determine which speed to set.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some hardware start settings implicitely assume an usual 1500 bytes mtu
that can't be guaranteed because changes of mtu may be requested both
before and after the hardware is started.
Reported-by: Tomi Orava <tomimo@ncircle.nullnet.fi>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit d64ec841517a25f6d468bde9f67e5b4cffdc67c7.
Jörg Otte reported his 8168evl to increase boot time link detection
from 1.6 to 10 s.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
|
|
This reverts commit e0c075577965d1c01b30038d38bf637b027a1df3.
Jörg Otte reported his 8168evl to fail boot time link detection.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
|
|
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was introduced in commit 6dccd16 "r8169: merge with version
6.001.00 of Realtek's r8169 driver". I did not find the version
6.001.00 online, but in 6.002.00 or any later r8169 from Realtek
this hunk is no longer present.
Also commit 05af214 "r8169: fix Ethernet Hangup for RTL8110SC
rev d" claims to have fixed this issue otherwise.
The magic compare mask of 0xfffe000 is dubious as it masks
parts of the Reserved part, and parts of the VLAN tag. But this
does not make much sense as the VLAN tag parts are perfectly
valid there. In matter of fact this seems to be triggered with
any VLAN tagged packet as RxVlanTag bit is matched. I would
suspect 0xfffe0000 was intended to test reserved part only.
Finally, this hunk is evil as it can cause more packets to be
handled than what was NAPI quota causing net/core/dev.c:
net_rx_action(): WARN_ON_ONCE(work > weight) to trigger, and
mess up the NAPI state causing device to hang.
As result, any system using VLANs and having high receive
traffic (so that NAPI poll budget limits rtl_rx) would result
in device hang.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 6f0333b ("r8169: use 50% less ram for RX ring") the rx
ring buffers are always copied making dirty_rx useless.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit: cb64edb6b89491edfdbae52ba7db9a8b8391d339 upstream
Above commit may introduce a race between cp_interrupt and dev_close
/ change MTU / dev_open up state. Changes cp_interrupt to tolerate
this. Change spin_locking in cp_interrupt to avoid possible
but unobserved race.
Reported-by: "Francois Romieu" <romieu@fr.zoreil.com>
Tested on virtual hardware, Tx MTU size up to 4096, max tx payload
was ping -s 4068 for MTU of 4096. No real hardware, need test
assist.
Signed-off-by: "John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: "David Woodhouse" <David.Woodhouse@intel.com>
Tested-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
|
|
GigaMAC registers have been reported left unitialized in several
situations:
- after cold boot from power-off state
- after S3 resume
Tweaking rtl_hw_phy_config takes care of both.
This patch removes an excess entry (",") at the end of the exgmac_reg
array as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/net-next
Networking: Remove __dev* markings from the networking drivers
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8139cp driver has a change_mtu function that has not been
enabled since the dawn of the git repository. However, the
generic eth_change_mtu is not used in its place, so that
invalid MTU values can be set on the interface.
Original patch salvages the broken code for the single case of
setting the MTU while the interface is down, which is safe
and also includes the range check. Now enhanced to support up
or down interface.
v2: fix case where rxbufsz isn't changed in the up state case
Original patch from
http://lkml.indiana.edu/hypermail/linux/kernel/1202.2/00770.html
Testing: has been test on virtual 8139cp setup without issue,
have no access real hardware 8139cp, need testing help.
Signed-off-by: "John Greene" <jogreene@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cp_open
[...]
rc = cp_alloc_rings(cp);
if (rc)
return rc;
cp_alloc_rings
[...]
mem = dma_alloc_coherent(&cp->pdev->dev, CP_RING_BYTES,
&cp->ring_dma, GFP_KERNEL);
- cp_alloc_rings never frees the coherent mapping it allocates
- neither do cp_open when cp_alloc_rings fails
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recovery doesn't work too well if we leave interrupts disabled...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for byte queue limits on RTL8139C+
Tested on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-By: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes (for me) a regression introduced by commit b01af457 ("8139cp:
set ring address before enabling receiver"). That commit configured the
descriptor ring addresses earlier in the initialisation sequence, in
order to avoid the possibility of triggering stray DMA before the
correct address had been set up.
Unfortunately, it seems that the hardware will scribble garbage into the
TxRingAddr registers when we enable "plus mode" Tx in the CpCmd
register. Observed on a Traverse Geos router board.
To deal with this, while not reintroducing the problem which led to the
original commit, we augment cp_start_hw() to write to the CpCmd register
*first*, then set the descriptor ring addresses, and then finally to
enable Rx and Tx in the original 8139 Cmd register. The datasheet
actually indicates that we should enable Tx/Rx in the Cmd register
*before* configuring the descriptor addresses, but that would appear to
re-introduce the problem that the offending commit b01af457 was trying
to solve. And this variant appears to work fine on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit b26623dab7eeb1e9f5898c7a49458789dd492f20.
This reverts the revert, in net-next we'll try another scheme
to fix this bug using patches from David Woodhouse.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/wireless/iwlwifi/pcie/tx.c
Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reverts b01af4579ec41f48e9b9c774e70bd6474ad210db.
The original patch was tested with emulated hardware. Real
hardware chokes.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=47041
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since eab6d18d (vlan: Don't check for vlan group before
vlan_tx_tag_present.) we don't check tp->vlgrp and thus
tp is not needed in this function.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
|
|
Signed-off-by: Dayanidhi Sreenivasan <dayanidhi.sreenivasan@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
Minor conflict between the BCM_CNIC define removal in net-next
and a bug fix added to net. Based upon a conflict resolution
patch posted by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
