Age | Commit message (Collapse) | Author |
|
commit 33b7107f59a61236d94ecd6b45e20283cd5abcc8 upstream.
In commit 6892b41d9701283085b655c6086fb57a5d63fa47
Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date: Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api
the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.
This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.
Reported-by: Jon Ringle <jon@ringle.org>
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
When IFF_ALLMULTI flag is set on interface and IFF_PROMISC isn't,
emac_dev_mcast_set should only enable RX of multicasts and reset
MACHASH registers.
It does this, but afterwards it either sets up multicast MACs
filtering or disables RX of multicasts and resets MACHASH registers
again, rendering IFF_ALLMULTI flag useless.
This patch fixes emac_dev_mcast_set, so that multicast MACs filtering and
disabling of RX of multicasts are skipped when IFF_ALLMULTI flag is set.
Tested with kernel 2.6.37.
Signed-off-by: Mariusz Ceier <mceier+kernel@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When interrupt pacing is enabled, receive/transmit statistics are not
updated properly by hardware which leads to ISR return with IRQ_NONE
and inturn kernel disables the interrupt. This patch removed the checking
of receive/transmit statistics from ISR.
This patch is verified with AM335x Beagle Bone Black and below is the
kernel warn when interrupt pacing is enabled.
[ 104.298254] irq 58: nobody cared (try booting with the "irqpoll" option)
[ 104.305356] CPU: 0 PID: 1073 Comm: iperf Not tainted 3.12.0-rc3-00342-g77d4015 #3
[ 104.313284] [<c001bb84>] (unwind_backtrace+0x0/0xf0) from [<c0017db0>] (show_stack+0x10/0x14)
[ 104.322282] [<c0017db0>] (show_stack+0x10/0x14) from [<c0507920>] (dump_stack+0x78/0x94)
[ 104.330816] [<c0507920>] (dump_stack+0x78/0x94) from [<c0088c1c>] (__report_bad_irq+0x20/0xc0)
[ 104.339889] [<c0088c1c>] (__report_bad_irq+0x20/0xc0) from [<c008912c>] (note_interrupt+0x1dc/0x23c)
[ 104.349505] [<c008912c>] (note_interrupt+0x1dc/0x23c) from [<c0086d74>] (handle_irq_event_percpu+0xc4/0x238)
[ 104.359851] [<c0086d74>] (handle_irq_event_percpu+0xc4/0x238) from [<c0086f24>] (handle_irq_event+0x3c/0x5c)
[ 104.370198] [<c0086f24>] (handle_irq_event+0x3c/0x5c) from [<c008991c>] (handle_level_irq+0xac/0x10c)
[ 104.379907] [<c008991c>] (handle_level_irq+0xac/0x10c) from [<c00866d8>] (generic_handle_irq+0x20/0x30)
[ 104.389812] [<c00866d8>] (generic_handle_irq+0x20/0x30) from [<c0014ce8>] (handle_IRQ+0x4c/0xb0)
[ 104.399066] [<c0014ce8>] (handle_IRQ+0x4c/0xb0) from [<c000856c>] (omap3_intc_handle_irq+0x60/0x74)
[ 104.408598] [<c000856c>] (omap3_intc_handle_irq+0x60/0x74) from [<c050d8e4>] (__irq_svc+0x44/0x5c)
[ 104.418021] Exception stack(0xde4f7c00 to 0xde4f7c48)
[ 104.423345] 7c00: 00000001 00000000 00000000 dd002140 60000013 de006e54 00000002 00000000
[ 104.431952] 7c20: de345748 00000040 c11c8588 00018ee0 00000000 de4f7c48 c009dfc8 c050d300
[ 104.440553] 7c40: 60000013 ffffffff
[ 104.444237] [<c050d8e4>] (__irq_svc+0x44/0x5c) from [<c050d300>] (_raw_spin_unlock_irqrestore+0x34/0x44)
[ 104.454220] [<c050d300>] (_raw_spin_unlock_irqrestore+0x34/0x44) from [<c00868c0>] (__irq_put_desc_unlock+0x14/0x38)
[ 104.465295] [<c00868c0>] (__irq_put_desc_unlock+0x14/0x38) from [<c0088068>] (enable_irq+0x4c/0x74)
[ 104.474829] [<c0088068>] (enable_irq+0x4c/0x74) from [<c03abd24>] (cpsw_poll+0xb8/0xdc)
[ 104.483276] [<c03abd24>] (cpsw_poll+0xb8/0xdc) from [<c044ef68>] (net_rx_action+0xc0/0x1e8)
[ 104.492085] [<c044ef68>] (net_rx_action+0xc0/0x1e8) from [<c0048a90>] (__do_softirq+0x100/0x27c)
[ 104.501338] [<c0048a90>] (__do_softirq+0x100/0x27c) from [<c0048cd0>] (do_softirq+0x68/0x70)
[ 104.510224] [<c0048cd0>] (do_softirq+0x68/0x70) from [<c0048e8c>] (local_bh_enable+0xd0/0xe4)
[ 104.519211] [<c0048e8c>] (local_bh_enable+0xd0/0xe4) from [<c048c774>] (tcp_rcv_established+0x450/0x648)
[ 104.529201] [<c048c774>] (tcp_rcv_established+0x450/0x648) from [<c0494904>] (tcp_v4_do_rcv+0x154/0x474)
[ 104.539195] [<c0494904>] (tcp_v4_do_rcv+0x154/0x474) from [<c043d750>] (release_sock+0xac/0x1ac)
[ 104.548448] [<c043d750>] (release_sock+0xac/0x1ac) from [<c04844e8>] (tcp_recvmsg+0x4d0/0xa8c)
[ 104.557528] [<c04844e8>] (tcp_recvmsg+0x4d0/0xa8c) from [<c04a8720>] (inet_recvmsg+0xcc/0xf0)
[ 104.566507] [<c04a8720>] (inet_recvmsg+0xcc/0xf0) from [<c0439744>] (sock_recvmsg+0x90/0xb0)
[ 104.575394] [<c0439744>] (sock_recvmsg+0x90/0xb0) from [<c043b778>] (SyS_recvfrom+0x88/0xd8)
[ 104.584280] [<c043b778>] (SyS_recvfrom+0x88/0xd8) from [<c043b7e0>] (sys_recv+0x18/0x20)
[ 104.592805] [<c043b7e0>] (sys_recv+0x18/0x20) from [<c0013da0>] (ret_fast_syscall+0x0/0x48)
[ 104.601587] handlers:
[ 104.603992] [<c03acd94>] cpsw_interrupt
[ 104.608040] Disabling IRQ #58
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If interrupts happen before napi_enable was called, the driver will not
work as expected. Network transmissions are impossible in this state.
This bug can be reproduced easily by restarting the network interface in
a loop. After some time any network transmissions on the network
interface will fail.
This patch fixes the bug by enabling napi before enabling the network
interface interrupts.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current implementation searches the whole DT for nodes named
"slave".
This patch changes it to search only child nodes for slaves.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed when the cpsw driver is built as module.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some phy's can be configured to enable wake on lan (e.g. at803x or marvell 88E1318S).
There is no way how to enable wol on CPSW with such connected phys. This patch
adds this support. It is provided by calling the phy's related code.
Tested on board with at8030x connected phy. Wol interrupt line is
connected to GPIO0 on am335x.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new IP version which is present in AM43xx SoC has a minor changes and the
offsets are same as the previous version, so adding new IP version support in
the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new IP version has a minor changes and the offsets are same as the
previous version, so adding new IP version support in the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net into net-next to setup some infrastructure Eric
Dumazet needs for usbnet changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQF_DISABLED is a no-op by now and should be
removed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding support for setting MAC address to cpsw device via ndo_set_mac_address
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to show CPSW hardware statistics to user via ethtool
so user can find if there were any error reported by hardware or
the system is over loaded duing high data rate transfer.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a999 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
|
|
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
|
|
davinci_emac_probe()
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cosmetic patch to add a newline after logging the device's MACID.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
guard the davinci_mdio_of_mtable table and davinci_mdio_probe_dt()
with CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch cleans up the OF parser code, removes unnecessary checks
on of_property_read_*() and guards davinci_emac_of_match table with
CONFIG_OF.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_ioremap_resource instead of devm_request_mem_region()/devm_ioremap()
and devm_request_irq() instead of request_irq().
This ensures more consistent error values and simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_suspend':
drivers/net/ethernet/ti/cpsw.c:1979:26: error: 'priv' undeclared (first use in this function)
drivers/net/ethernet/ti/cpsw.c:1979:26: note: each undeclared identifier is reported only once for each function it appears in
make[4]: *** [drivers/net/ethernet/ti/cpsw.o] Error 1
The compilation error was introduced by the following commit
6d3d76f (drivers: net: cpsw: fix cpsw clock gating issue across suspend/resume)
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the DMA mapping may fail the caller should check the return value.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to some hardware integration issue, CPSW sliver modules requires a
reset across suspend/resume cycle for a successful clock gating to
CPGMAC (CPSW and Davinci MDIO) in AM335x PG1.0.
This issue is fixed in PG2.x, though to support suspend/resume on PG1.0
this reset is required.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
after priv->cpts got allocated then this pointer should check to determine
if the allocation succeeded or not.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This utilize the new pinctrl core PM helpers to transition
the driver to "default" and "sleep" states.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This utilize the new pinctrl core PM helpers to transition
the driver to "default" and "sleep" states.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
During suspend resume cycle all the register data is lost, so MDIO
clock divier value gets reset. This patch restores the clock divider
value.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MDIO driver should resume before CPSW ethernet driver so that CPSW connect
to the phy and start tx/rx ethernet packets, changing the suspend/resume
apis with suspend_late/resume_early.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
was playing with suspend and run into this:
|BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891
|in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash
|6 locks held by bash/1963:
|CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50
|[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14)
|[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac)
|[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c)
|[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54)
|[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64)
|[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c)
|[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230)
|[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350)
|[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c)
|[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc)
|[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20)
|[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c)
|[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190)
|[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70)
|[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48)
I don't see a reason why the pm_runtime call must be under the lock.
Further I don't understand why this is a spinlock and not mutex.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding phy-mode support to cpsw driver and updating the cpsw binding
documentation.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Additional 4 bytes found in the skb is the CRC calculated by the
CPDMA hardware, check the CRC bit in CPDMA status field of
Descriptor and remove the CRC length from the skb. This extra
4 byte can be seen when capturing packets using tcpdump.
This has been tested in TI816x platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d0631001288a5974afc0b2a5f568bcdecb4d
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These 2 places are the only matches for is_eisa in the whole tree.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In CPSW NAPI, after processing all interrupts IRQ is enabled and then book
keeping irq_enabled is updated. In random cases when a packet is transmitted
or received between processing packets and IRQ enabled, then just after
enabled IRQ and before irq_enabled is updated, ISR is called so IRQs are
not disabled as irq_enabled is still false and CPU gets locked in CPSW ISR.
By changing the sequence as update the irq_enabled and then enable IRQ
fixes the issue. This issue is not captured always as it is a timing issue
whether Tx or Rx IRQ is invoked between packet processing and enable IRQ.
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"Highlights (1721 non-merge commits, this has to be a record of some
sort):
1) Add 'random' mode to team driver, from Jiri Pirko and Eric
Dumazet.
2) Make it so that any driver that supports configuration of multiple
MAC addresses can provide the forwarding database add and del
calls by providing a default implementation and hooking that up if
the driver doesn't have an explicit set of handlers. From Vlad
Yasevich.
3) Support GSO segmentation over tunnels and other encapsulating
devices such as VXLAN, from Pravin B Shelar.
4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.
5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
Dukkipati.
6) In the PHY layer, allow supporting wake-on-lan in situations where
the PHY registers have to be written for it to be configured.
Use it to support wake-on-lan in mv643xx_eth.
From Michael Stapelberg.
7) Significantly improve firewire IPV6 support, from YOSHIFUJI
Hideaki.
8) Allow multiple packets to be sent in a single transmission using
network coding in batman-adv, from Martin Hundebøll.
9) Add support for T5 cxgb4 chips, from Santosh Rastapur.
10) Generalize the VXLAN forwarding tables so that there is more
flexibility in configurating various aspects of the endpoints.
From David Stevens.
11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
from Dmitry Kravkov.
12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
Neira Ayuso.
13) Start adding networking selftests.
14) In situations of overload on the same AF_PACKET fanout socket, or
per-cpu packet receive queue, minimize drop by distributing the
load to other cpus/fanouts. From Willem de Bruijn and Eric
Dumazet.
15) Add support for new payload offset BPF instruction, from Daniel
Borkmann.
16) Convert several drivers over to mdoule_platform_driver(), from
Sachin Kamat.
17) Provide a minimal BPF JIT image disassembler userspace tool, from
Daniel Borkmann.
18) Rewrite F-RTO implementation in TCP to match the final
specification of it in RFC4138 and RFC5682. From Yuchung Cheng.
19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
you like netlink, so I implemented netlink dumping of netlink
sockets.") From Andrey Vagin.
20) Remove ugly passing of rtnetlink attributes into rtnl_doit
functions, from Thomas Graf.
21) Allow userspace to be able to see if a configuration change occurs
in the middle of an address or device list dump, from Nicolas
Dichtel.
22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
Frederic Sowa.
23) Increase accuracy of packet length used by packet scheduler, from
Jason Wang.
24) Beginning set of changes to make ipv4/ipv6 fragment handling more
scalable and less susceptible to overload and locking contention,
from Jesper Dangaard Brouer.
25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
instead. From Hong Zhiguo.
26) Optimize route usage in IPVS by avoiding reference counting where
possible, from Julian Anastasov.
27) Convert IPVS schedulers to RCU, also from Julian Anastasov.
28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
Eitzenberger.
29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
nfnetlink_log, and nfnetlink_queue. From Gao feng.
30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.
31) Support several new r8169 chips, from Hayes Wang.
32) Support tokenized interface identifiers in ipv6, from Daniel
Borkmann.
33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.
34) Add 802.1ad vlan offload support, from Patrick McHardy.
35) Support mmap() based netlink communication, also from Patrick
McHardy.
36) Support HW timestamping in mlx4 driver, from Amir Vadai.
37) Rationalize AF_PACKET packet timestamping when transmitting, from
Willem de Bruijn and Daniel Borkmann.
38) Bring parity to what's provided by /proc/net/packet socket dumping
and the info provided by netlink socket dumping of AF_PACKET
sockets. From Nicolas Dichtel.
39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
Poirier"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
filter: fix va_list build error
af_unix: fix a fatal race with bit fields
bnx2x: Prevent memory leak when cnic is absent
bnx2x: correct reading of speed capabilities
net: sctp: attribute printl with __printf for gcc fmt checks
netlink: kconfig: move mmap i/o into netlink kconfig
netpoll: convert mutex into a semaphore
netlink: Fix skb ref counting.
net_sched: act_ipt forward compat with xtables
mlx4_en: fix a build error on 32bit arches
Revert "bnx2x: allow nvram test to run when device is down"
bridge: avoid OOPS if root port not found
drivers: net: cpsw: fix kernel warn on cpsw irq enable
sh_eth: use random MAC address if no valid one supplied
3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
tg3: fix to append hardware time stamping flags
unix/stream: fix peeking with an offset larger than data in queue
unix/dgram: fix peeking with an offset larger than data in queue
unix/dgram: peek beyond 0-sized skbs
openvswitch: Remove unneeded ovs_netdev_get_ifindex()
...
|
|
With the commit a11fbba (net/cpsw: fix irq_disable() with threaded interrupts)
from Sebastian Siewior, a kernel warning is generated as below. This warning
is generated as the irq_enabled is not initialized for the primary interface
and in probe it is initialized for the second interface. This patch moves
irq_enabled initialization from second interface to primary interface.
[ 3.049173] net eth0: phy found : id is : 0x4dd074
[ 3.054552] net eth0: phy found : id is : 0x4dd074
[ 3.070421] ------------[ cut here ]------------
[ 3.075308] WARNING: at kernel/irq/manage.c:437 enable_irq+0x3c/0x74()
[ 3.082173] Unbalanced enable for IRQ 56
[ 3.086299] Modules linked in:
[ 3.089557] [<c001abcc>] (unwind_backtrace+0x0/0xf0) from [<c004294c>] (warn_slowpath_common+0x4c/0x68)
[ 3.099450] [<c004294c>] (warn_slowpath_common+0x4c/0x68) from [<c00429fc>] (warn_slowpath_fmt+0x30/0x40)
[ 3.109521] [<c00429fc>] (warn_slowpath_fmt+0x30/0x40) from [<c00a29fc>] (enable_irq+0x3c/0x74)
[ 3.118681] [<c00a29fc>] (enable_irq+0x3c/0x74) from [<c03a7818>] (cpsw_ndo_open+0x61c/0x684)
[ 3.127669] [<c03a7818>] (cpsw_ndo_open+0x61c/0x684) from [<c0445c08>] (__dev_open+0x9c/0xf8)
[ 3.136646] [<c0445c08>] (__dev_open+0x9c/0xf8) from [<c0445e34>] (__dev_change_flags+0x78/0x13c)
[ 3.145988] [<c0445e34>] (__dev_change_flags+0x78/0x13c) from [<c0445f64>] (dev_change_flags+0x10/0x48)
[ 3.155884] [<c0445f64>] (dev_change_flags+0x10/0x48) from [<c0736d88>] (ip_auto_config+0x198/0x111c)
[ 3.165592] [<c0736d88>] (ip_auto_config+0x198/0x111c) from [<c00086a4>] (do_one_initcall+0x34/0x180)
[ 3.175309] [<c00086a4>] (do_one_initcall+0x34/0x180) from [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8)
[ 3.185393] [<c07078f8>] (kernel_init_freeable+0xfc/0x1c8) from [<c04f36ec>] (kernel_init+0x8/0xe4)
[ 3.194929] [<c04f36ec>] (kernel_init+0x8/0xe4) from [<c00133d0>] (ret_from_fork+0x14/0x24)
[ 3.203712] ---[ end trace d6f979da080bc391 ]---
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual stuff, mostly comment fixes, typo fixes, printk fixes and small
code cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (45 commits)
mm: Convert print_symbol to %pSR
gfs2: Convert print_symbol to %pSR
m32r: Convert print_symbol to %pSR
iostats.txt: add easy-to-find description for field 6
x86 cmpxchg.h: fix wrong comment
treewide: Fix typo in printk and comments
doc: devicetree: Fix various typos
docbook: fix 8250 naming in device-drivers
pata_pdc2027x: Fix compiler warning
treewide: Fix typo in printks
mei: Fix comments in drivers/misc/mei
treewide: Fix typos in kernel messages
pm44xx: Fix comment for "CONFIG_CPU_IDLE"
doc: Fix typo "CONFIG_CGROUP_CGROUP_MEMCG_SWAP"
mmzone: correct "pags" to "pages" in comment.
kernel-parameters: remove outdated 'noresidual' parameter
Remove spurious _H suffixes from ifdef comments
sound: Remove stray pluses from Kconfig file
radio-shark: Fix printk "CONFIG_LED_CLASS"
doc: put proper reference to CONFIG_MODULE_SIG_ENFORCE
...
|
|
During high throughput it is likely that we receive both: an RX and TX
interrupt. The normal behaviour is that once we enter the ISR the
interrupts are disabled in the IRQ chip and so the ISR is invoked only
once and the interrupt line is disabled once. It will be re-enabled
after napi completes.
With threaded interrupts on the other hand the interrupt the interrupt
is disabled immediately and the ISR is marked for "later". By having TX
and RX interrupt marked pending we invoke them both and disable the
interrupt line twice. The napi callback is still executed once and so
after it completes we remain with interrupts disabled.
The initial patch simply removed the cpsw_{enable|disable}_irq() calls
and it worked well on my AM335X ES1.0 (beagle bone). On ES2.0 (beagle
bone black) it caused an never ending interrupt (even after the mask via
cpsw_intr_disable()) according to Mugunthan V N. Since I don't have the
ES2.0 and no idea what is going on this patch tracks the state of the
irq_disable() call and execute it only when not yet done.
The book keeping is done on the first struct since with dual_emac we can
have two of those and only one interrupt line.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
text data bss dec hex filename
15530 92 4 15626 3d0a cpsw.o.before
15478 92 4 15574 3cd6 cpsw.o.after
52 bytes smaller, 13 for each invocation.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|