| Age | Commit message (Collapse) | Author |
|---|
|
This patch updates igb driver version to 5.0.5
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes the way we report supported/advertised link for i354
devices, especially for 2.5 GB. Instead of reporting 2.5 GB for all i354
devices erroneously, check first, if it is 2.5 GB capable.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes how we get speed/duplex for non_copper devices; it
now uses pcs register to get current speed and duplex instead of using
generic status register that we use to detect speed/duplex for copper
devices.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Since i354 2.5Gb devices are not Copper media type but SerDes, so this
patch changes the way we detect speed/duplex link info for this device.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PHY Power Management does not exist for i354 device. So, there is no
need to read and write this register or clear go link Disconnect bit,
which could cause a lot of issues.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch implements downshift mechanism for M88E1543 PHY, so that
downshift is disabled first during link setup process, and later enabled
if we are master and downshift link is negotiated. Also cleaned up
return code implementation.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes PHY_ID for i354 device, now using M88E1543
instead of M88E1545.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds 1 sec delay mechanism to i210 device family, in order
to avoid erroneous link issue with the link partner.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a part is flashless, do not look for a PBA in the iNVM.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Just remove a small semicolon.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes warning "warning: symbol 'qlcnic_set_dcb_ops' was
not declared. Should it be static?"
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hypervisor is big endian, so little endian kernel builds need
to byteswap.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Casting from 'void *' is unnecessary, because casting from 'void *'
to any pointer type is automatic.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use bp->pfid from bnx2x instead to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use BP_PORT and chip_port_mode directly from bnx2x.h to avoid duplication.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
to avoid duplication of the same logic.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This eliminates duplication and ensures that all bnx2x chips will be
supported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper functions for getting and setting the driver data
using pci_dev instead of using dev_{get,set}_drvdata() with
&pdev->dev, so we can directly pass a struct pci_dev. This is
a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the wrapper functions for getting and setting the driver data
using platform_device instead of using dev_{get,set}_drvdata()
with &pdev->dev, so we can directly pass a struct platform_device.
This is a purely cosmetic change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
H8300H_H8MAX dependancy for NE_H8300
Currently only H8300H_AKI3068NET and H8300H_H8MAX define default
I/O base and IRQ values for the NE_H8300 driver. Hence builds
for other H8300H platforms will fail as per below. Since H8300H
does not support multi platform builds, we simply limit building
the driver to those two platforms specifically.
The release error:
drivers/net/ethernet/8390/ne-h8300.c: In function 'init_dev':
drivers/net/ethernet/8390/ne-h8300.c:117:23: error: 'h8300_ne_base' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:117:23: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/8390/ne-h8300.c:117:23: error: bit-field '<anonymous>' width not an integer constant
drivers/net/ethernet/8390/ne-h8300.c:119:20: error: 'h8300_ne_irq' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c: In function 'init_module':
drivers/net/ethernet/8390/ne-h8300.c:647:21: error: 'h8300_ne_base' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:648:15: error: 'h8300_ne_irq' undeclared (first use in this function)
drivers/net/ethernet/8390/ne-h8300.c:661:4: warning: format '%x' expects argument of type 'unsigned int', but argument 2 has type 'long unsigned int' [-Wformat]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script: (and a little typing)
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Turning off led on port 0 of the 5719 serdes causes all other ports to
lose power and stop functioning. Add tg3_phy_led_bug() function to check
for this condition. We use a switch() in tg3_phy_led_bug() for
consistency with the tg3_phy_power_bug() function.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a DMA mapping error in xgmac_xmit, we should simply free the skb and
return NETDEV_TX_OK rather than -EIO. In the case of errors in mapping
frags, we need to undo everything that has been setup.
Reported-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the mismatch in the DMA mapping and unmapping sizes for receive. The
unmap size must be equal to the map size and should not be the actual
received frame length. The map size should also be adjusted by the
NET_IP_ALIGN size since the h/w buffer size (dma_buf_sz) includes this
offset.
Also, add a missing dma_mapping_error check in xgmac_rx_refill.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rx_sa_filter_fail and tx_undeflow events are unused and impossible
to occur based on how the h/w is used. We never filter on source MAC
address and TX store and forward mode prevents underflow events.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix xgmac_set_rx_mode to handle several conditions that were not handled
correctly as Lennert Buytenhek describes:
If we have, say, 100 unicast addresses, and 5 multicast addresses, the
unicast address count check will evaluate to true, and set use_hash to
true. The multicast address check will however evaluate to false, and
use_hash won't be set to true again, and XGMAC_FRAME_FILTER_HMC won't
be OR'd into XGMAC_FRAME_FILTER, but since use_hash was still true
from the unicast check, netdev_for_each_mc_addr() will program the
multicast addresses into the hash table instead of using the MAC
address registers, but since the HMC bit wasn't set, the hash table
won't be checked for multicast addresses on receive, and we'll stop
receiving multicast packets entirely.
Also, there is no code that zeroes out MAC address registers reg..31
at the end of this function, meaning that under the right conditions,
unicast/multicast addresses that were previously in the filter but
were then deleted won't be cleared out.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a race condition where the interrupt handler may have called
napi_schedule before napi_enable is called. This would disable interrupts
and never actually schedule napi to run.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the xgmac transmit start and completion work locklessly, it is
possible for xgmac_xmit to stop the tx queue after the xgmac_tx_complete
has run resulting in the tx queue never being woken up. Fix this by
ensuring that ring buffer index updates are visible and recheck the ring
space after stopping the queue. Also fix an off-by-one bug where we need
to stop the queue when the ring buffer space is equal to MAX_SKB_FRAGS.
The implementation used here was copied from
drivers/net/ethernet/broadcom/tg3.c.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that the descriptor writes are visible before the ring buffer head
is updated. Since writel is a barrier, we can simply update the head after
the writel.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX completion code may have freed an skb before the entire sg list
was transmitted. The DMA unmap calls for the fragments could also get
skipped. Now set the skb pointer on every entry in the ring, not just
the head of the sg list. We then use the FS (first segment) bit in the
descriptors to determine skb head vs. fragment.
This also fixes similar bug in xgmac_free_tx_skbufs where clean-up of
a sg list that wraps at the end of the ring buffer would not get
unmapped.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible for the xgmac_tx_complete to run concurrently with
xgmac_tx_err since there are no locks. Fix this by moving the tx
error handling to a workqueue so we can disable napi while we reset
the transmitter.
Reported-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xgmac_desc_get_buf_len appears to have a copy/paste error. flags is the
wrong field to read. We should be reading buf_size field. cpu_to_le32
should also be le32_to_cpu. This never really mattered as this function
is only used for DMA mapping calls which happen to be nops with coherent
DMA.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The xgmac does not actually handle frag lists, so this option should not
be set. It does not appear to have had any impact though.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SkyHawk-R can support VEB or VEPA mode.
This patch will allow the user to set/query this switch setting.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the amount of sent bytes reported to BQL by reporting the
number of bytes on wire in the xmit routine, and recording that
value for each skb in order to be correctly confirmed on Tx
confirmation cleanup.
Reporting skb->len to BQL just before exiting xmit is not correct
due to possible insertions of TOE block and alignment bytes in the
skb->data, which are being stripped off by the controller before
transmission on wire. This led to mismatch of (incorrectly)
reported bytes to BQL b/w xmit and Tx confirmation, resulting in
Tx timeout firing, for the h/w tx timestamping acceleration case.
There's no easy way to obtain the number of bytes on wire in the Tx
confirmation routine, so skb->cb is used to convey that information
from xmit to Tx confirmation, for now (as proposed by Eric). Revived
the currently unused GFAR_CB() construct for that purpose.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This corrects an oversight when r8a7790 support was added to sh_eth.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
PCI device hotplug:
- Use PCIe native hotplug, not ACPI hotplug, when possible (Neil Horman)
- Assign resources on per-host bridge basis (Yinghai Lu)
MPS (Max Payload Size):
- Allow larger MPS settings below hotplug-capable Root Port (Yijing Wang)
- Add warnings about unsafe MPS settings (Yijing Wang)
- Simplify interface and messages (Bjorn Helgaas)
SR-IOV:
- Return -ENOSYS on non-SR-IOV devices (Stefan Assmann)
- Update NumVFs register when disabling SR-IOV (Yijing Wang)
Virtualization:
- Add bus and slot reset support (Alex Williamson)
- Fix ACS (Access Control Services) issues (Alex Williamson)
Miscellaneous:
- Simplify PCIe Capability accessors (Bjorn Helgaas)
- Add pcibios_pm_ops for arch-specific hibernate stuff (Sebastian Ott)
- Disable decoding during BAR sizing only when necessary (Zoltan Kiss)
- Delay enabling bridges until they're needed (Yinghai Lu)
- Split Designware support into Synopsys and Exynos parts (Jingoo Han)
- Convert class code to use dev_groups (Greg Kroah-Hartman)
- Cleanup Designware and Exynos I/O access wrappers (Seungwon Jeon)
- Fix bridge I/O window alignment (Bjorn Helgaas)
- Add pci_wait_for_pending_transaction() (Casey Leedom)
- Use devm_ioremap_resource() in Marvell driver (Tushar Behera)
* tag 'pci-v3.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (63 commits)
PCI/ACPI: Fix _OSC ordering to allow PCIe hotplug use when available
PCI: exynos: Add I/O access wrappers
PCI: designware: Drop "addr" arg from dw_pcie_readl_rc()/dw_pcie_writel_rc()
PCI: Remove pcie_cap_has_devctl()
PCI: Support PCIe Capability Slot registers only for ports with slots
PCI: Remove PCIe Capability version checks
PCI: Allow PCIe Capability link-related register access for switches
PCI: Add offsets of PCIe capability registers
PCI: Tidy bitmasks and spacing of PCIe capability definitions
PCI: Remove obsolete comment reference to pci_pcie_cap2()
PCI: Clarify PCI_EXP_TYPE_PCI_BRIDGE comment
PCI: Rename PCIe capability definitions to follow convention
PCI: Warn if unsafe MPS settings detected
PCI: Fix MPS peer-to-peer DMA comment syntax
PCI: Disable decoding for BAR sizing only when it was actually enabled
PCI: Add comment about needing pci_msi_off() even when CONFIG_PCI_MSI=n
PCI: Add pcibios_pm_ops for optional arch-specific hibernate functionality
PCI: Don't restrict MPS for slots below Root Ports
PCI: Simplify MPS test for Downstream Port
PCI: Remove unnecessary check for pcie_get_mps() failure
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
|
|
'qib' into for-next
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is an embedded switch per physical port on the adapter.
Add support for enabling and disabling the embedded switch
on per port basis.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Removed unused and unnecessary members from qlc_83xx_fw_info
structure.
o Made fw_info member of qlcnic_hardware_context as a pointer to
qlc_83xx_fw_info structure.
o Added a member fw_file_name to qlc_83xx_fw_info structure which
will hold the name of firmware image file name.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Generic AER callback handlers will make use of qlcnic_hardware_ops structure
to call adapter specific handlers.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
-Use CAMRAM register to store firmware dump state in adapter
instead of maintaining it in each function driver separately.
-Return appropriate error code on failure
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
