| Age | Commit message (Collapse) | Author |
|---|
|
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This updates the network drivers so that they don't access the
ethtool_cmd::speed field directly, but use ethtool_cmd_speed()
instead.
For most of the drivers, these changes are purely cosmetic and don't
fix any problem, such as for those 1GbE/10GbE drivers that indirectly
call their own ethtool get_settings()/mii_ethtool_gset(). The changes
are meant to enforce code consistency and provide robustness with
future larger throughputs, at the expense of a few CPU cycles for each
ethtool operation.
All drivers compiled with make allyesconfig ion x86_64 have been
updated.
Tested: make allyesconfig on x86_64 + e1000e/bnx2x work
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylib would silently ignore the phy_id argument to these ioctls and
perform the read/write with the active phydev address, whereas most
non-phylib drivers seem to allow access to all mdio addresses
(E.G. pcnet_cs).
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: netdev@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following functions are not used directly by any drivers:
phy_attach_direct
phy_device_create
phy_prepare_link
genphy_config_advert
genphy_setup_forced
phy_config_interrupt
phy_clear_interrypt
phy_sanitize_settings
phy_enable_interrupts
phy_disable_interrupts
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix phy.c kernel-doc notation:
Warning(drivers/net/phy/phy.c:313): No description found for parameter 'ifr'
Warning(drivers/net/phy/phy.c:313): Excess function parameter 'mii_data' description in 'phy_mii_ioctl'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.
The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
implicit slab.h inclusion from percpu.h
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
|
|
commit 541cd3ee00a4fe975b22fac6a3bc846bacef37f7 ("phylib: Fix deadlock
on resume") caused TI DaVinci EMAC ethernet driver to oops upon resume:
PM: resume of devices complete after 237.098 msecs
Restarting tasks ... done.
kernel BUG at kernel/workqueue.c:354!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
[...]
Backtrace:
[<c002c598>] (__bug+0x0/0x2c) from [<c0052a54>] (queue_delayed_work_on+0x74/0xf8)
[<c00529e0>] (queue_delayed_work_on+0x0/0xf8) from [<c0052b30>] (queue_delayed_work+0x2c/0x30)
The oops pops up because TI DaVinci EMAC driver detaches PHY on
suspend and attaches it back on resume. Attaching makes phylib call
phy_start_machine() that initializes a workqueue. On the other hand,
PHY's resume routine will call phy_start_machine() again, and that
will cause the oops since we just destroyed the already scheduled
workqueue.
This patch fixes the issue by moving workqueue initialization to
phy_device_create().
p.s. We don't see this oops with ucc_geth and gianfar drivers because
they perform a fine-grained suspend, i.e. they just stop the PHYs
without detaching.
Reported-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_ioctl() already checks capable(CAP_NET_ADMIN) before calling the
driver's implementation of MDIO ioctls.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY_HALTED state disables phydev->link, but the link will not be
updated upon entering PHY_RESUMING. Add a call to phy_read_status() to
update the link before entering PHY_RUNNING. If the link is not up at
this point, enter the PHY_NOLINK state instead.
Also, when transitioning from PHY_RESUMING to PHY_RUNNING, calls to
netif_carrier_on() and phydev->adjust_link() are missing. Add the calls
similar to the other transitions to PHY_RUNNING.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit a390d1f3 ("phylib: convert state_queue work to
delayed_work") missed converting 'expires' value to 'delay' value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marvell 88E1121R Dual PHY device can be hardware-configured
to use shared interrupt pin for both PHY ports. For such
PHY configurations using shared PHY interrupt phy_interrupt()
handler will also schedule a work for PHY port which didn't
cause an interrupt.
This patch adds a possibility for PHY drivers to provide
did_interrupt() function which reports if the PHY (or a PHY
port in a multi-PHY device) generated an interrupt. This
function is called in phy_change() as phy_change() shouldn't
proceed if it is invoked for a PHY which didn't cause an
interrupt. So check for interrupt originator in phy_change()
to allow early-out.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is a fairly common operation to have a pointer to a work and to need a
pointer to the delayed work it is contained in. In particular, all
delayed works which want to rearm themselves will have to do that. So it
would seem fair to offer a helper function for this operation.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg KH <greg@kroah.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.
Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add mdiobus_{read,write} routines to allow direct reading/writing
of registers on an mii bus without having to go through the PHY
abstraction, and make phy_{read,write} use these primitives.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This way the phy layer will respond to a change in phy state immediately,
instead of up to one second later when the state machine timer runs.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the SIOCGMIIPHY case fall through properly (it is supposed
to not only return the ID of the default PHY but also to read from
that PHY), and make phy_mii_ioctl() return the same error code as
generic_mii_ioctl() in case of an unsupported operation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Declared some things static, declared some things in the header.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
Sometimes the specific interaction between the platform and the PHY
requires special handling. For instance, to change where the PHY's
clock input is, or to add a delay to account for latency issues in the
data path. We add a mechanism for registering a callback with the PHY
Lib to be called on matching PHYs when they are brought up, or reset.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
PHY read/write functions can potentially sleep (e.g., a PHY accessed
via I2C). The following changes were made to account for this:
* Change spin locks to mutex locks
* Add a BUG_ON() to phy_read() phy_write() to warn against
calling them from an interrupt context.
* Use work queue for PHY state machine handling since
it can potentially sleep
* Change phydev lock from spinlock to mutex
Signed-off-by: Nate Case <ncase@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This kind of sucks, and prevents the Fedora installer from using the
device for network installs...
[root@efika phy]# iwconfig eth0
Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...
eth0 ESSID:off/any Nickname:""
NWID:0 Channel:0 Access Point: 00:00:BF:81:14:E0
Bit Rate:-1.08206e+06 kb/s Sensitivity=0/0
RTS thr:off Fragment thr:off
Encryption key:<too big>
Power Management:off
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Ensure the PHY_HALTED state is not entered with the IRQ asserted as it
could lead to an interrupt loop.
There is a small window in phy_stop(), where the state of the PHY machine
indicates it has been halted, but its interrupt output might still be
unmasked. If an interrupt goes active right at this moment it will loop as
the phy_interrupt() handler exits immediately with IRQ_NONE if the halted
state is seen. It is unsafe to extend the phydev spinlock to cover
phy_interrupt(). It is safe to swap the order of the actions though as all
the competing places to unmask the interrupt output of the PHY, which are
phy_change() and phy_timer() are already covered with the lock as is the
sequence in question.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Keep track of disable_irq_nosync() invocations and call enable_irq() the
right number of times if work has been cancelled that would include them.
Now that the call to flush_work_keventd() (problematic because of
rtnl_mutex being held) has been replaced by cancel_work_sync() another
issue has arisen and been left unresolved. As the MDIO bus cannot be
accessed from the interrupt context the PHY interrupt handler uses
disable_irq_nosync() to prevent from looping and schedules some work to be
done as a softirq, which, apart from handling the state change of the
originating PHY, is responsible for reenabling the interrupt. Now if the
interrupt line is shared by another device and a call to the softirq
handler has been cancelled, that call to enable_irq() never happens and the
other device cannot use its interrupt anymore as its stuck disabled.
I decided to use a counter rather than a flag because there may be more
than one call to phy_change() cancelled in the queue -- a real one and a
fake one triggered by free_irq() if DEBUG_SHIRQ is used, if nothing else.
Therefore because of its nesting property enable_irq() has to be called the
right number of times to match the number disable_irq_nosync() was called
and restore the original state. This DEBUG_SHIRQ feature is also the
reason why free_irq() has to be called before cancel_work_sync().
While at it I updated the comment about phy_stop_interrupts() being called
from `keventd' -- this is no longer relevant as the use of
cancel_work_sync() makes such an approach unnecessary. OTOH a similar
comment referring to flush_scheduled_work() in phy_stop() still applies as
using cancel_work_sync() there would be dangerous.
Checked with checkpatch.pl and at the run time (with and without
DEBUG_SHIRQ).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Use spin_lock_bh()/spin_unlock_bh() for the phydev lock throughout as it
is used in phy_timer() that is called as a softirq and all the other
operations may happen in the user context.
There has been a change recently that did such a conversion for some of the
operations on the lock, but some have been left intact. Many of them,
perhaps all, may be called in the user context and I was able to trigger
recursive spinlock acquisition indeed, so I think for the sake of long-term
maintenance it is best to convert them all, even if unnecessarily for one
or two -- better safe than sorry.
Perhaps one in phy_timer() could actually be skipped as only called as a
softirq -- I can send an update if that sounds like a good idea.
Checked with checkpatch.pl and at the runtime.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Export phy_mii_ioctl, so network drivers can use it when built
as modules too.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Lock debugging finds a problem in phy.c and phy_device.c,
this patch fixes it. Tested on an AT91SAM9263-EK board,
kernel 2.6.23-rc4.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix a thinko (?) in setting phydev->autoneg.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
flush_work(wq, work) doesn't need the first parameter, we can use cwq->wq
(this was possible from the very beginnig, I missed this). So we can unify
flush_work_keventd and flush_work.
Also, rename flush_work() to cancel_work_sync() and fix all callers.
Perhaps this is not the best name, but "flush_work" is really bad.
(akpm: this is why the earlier patches bypassed maintainers)
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
(akpm: bypassed maintainers, sorry. There are other patches which depend on
this)
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Function `phy_mii_ioctl' returns physical device's information based on
user requests. When requested to return the basic mode control register
information (BMCR), the original implementation only returns the physical
device's duplex information and forgets to return speed information, which
should not be because BMCR register is used to hold both duplex and speed
information.
The patch checks the BMCR value against speed-related flags and fills the
return structure's speed field accordingly.
Signed-off-by: Shan <shanlu@cs.uiuc.edu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Convert function documentation in drivers/net/phy/ to kernel-doc
and add it to DocBook.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We need to export phy_ethtool_gset and phy_ethtool_sset to allow drivers that
use these functions to be built as modules.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This allows workqueue users to run just their own pending work, rather
than wait for the whole workqueue to finish running. This solves the
deadlock with networking libphy that was due to other workqueue entries
possibly needing a lock that was held by the routine that wanted to
flush its own work.
It's not wonderful: if you absolutely need to synchronize with the work
function having been executed, any user strictly speaking should have
its own completion tracking logic, since when we run things explicitly
by hand, the generic workqueue layer can no longer help us synchronize.
Also, this is strictly only usable for work that has been scheduled
without any delayed timers. You can not mix the new interface with
schedule_delayed_work().
But it's better than what we had currently.
Acked-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
* genphy_update_link is now exported
* Added a fix from ncase@xes-inc.com which changes forcing so it
only updates the link. Otherwise, it never tries the lower
values, since it is always overwriting the speed/duplex values
with the current ones, rather than the intended ones.
* Fixed a bug where bringing up a PHY with no link caused it to
timeout, and enter forcing mode. Once in forcing mode,
plugging in the link didn't autonegotiate. Now the AN state
detects the lack of link, and enters the NO_LINK state. AN
only times out if the link is up and AN fails
* Cleaned up the PHY_AN case, reducing one level of indentation
for the timeout code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
This patch fixes a couple of problems discovered with interrupt handling
in the phylib core, namely:
1. The driver uses timer and workqueue calls, but does not include
<linux/timer.h> nor <linux/workqueue.h>.
2. The driver uses schedule_work() for handling interrupts, but does not
make sure any pending work scheduled thus has been completed before
driver's structures get freed from memory. This is especially
important as interrupts may keep arriving if the line is shared with
another PHY.
The solution is to ignore phy_interrupt() calls if the reported device
has already been halted and calling flush_scheduled_work() from
phy_stop_interrupts() (but guarded with current_is_keventd() in case
the function has been called through keventd from the MAC device's
close call to avoid a deadlock on the netlink lock).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
patch-mips-2.6.18-20060920-phy-irq-16
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Fix up for make allyesconfig.
Signed-Off-By: David Howells <dhowells@redhat.com>
|
|
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
|
|
Prevent phylib from freeing PHY IRQ twice on closing an eth device:
phy_disconnect() first calls phy_stop_interrupts(), then it calls
phy_stop_machine() which in turn calls phy_stop_interrupts() making the
kernel complain on each bootup...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
|
|
phy device
Add the PHY_ID_FMT macro to ensure that the format of the id string used by a
driver to match to its specific phy is consistent between the mdio_bus and the
driver.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
