| Age | Commit message (Collapse) | Author |
|---|
|
The function virtnet_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Saves us one cycle of alloc-add-free if the queue was full.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (modified)
|
|
Now we can tell the theoretical capacity remaining in the output
queue, virtio_net can waste entries by stopping the queue early.
It doesn't work in the case of indirect buffers and kmalloc failure,
but that's rare (we could drop the packet in that case, but other
drivers return TX_BUSY for similar reasons).
For the record, I think this patch reflects poorly on the linux
network API.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
|
|
We put the virtio_net_hdr into the skb's cb region; turn this into a
union to clean up the code slightly and allow future expansion.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mark McLoughlin <markmc@redhat.com>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
|
|
The virtio_net driver is complicated by the two methods of freeing old
xmit buffers (in addition to freeing old ones at the start of the xmit
path).
The original code used a 1/10 second timer attached to xmit_free(),
reset on every xmit. Before we orphaned skbs on xmit, the
transmitting userspace could block with a full socket until the timer
fired, the skb destructor was called, and they were re-woken.
So we added the VIRTIO_F_NOTIFY_ON_EMPTY feature: supporting devices
send an interrupt (even if normally suppressed) on an empty xmit ring
which makes us schedule xmit_tasklet(). This was a benchmark win.
Unfortunately, VIRTIO_F_NOTIFY_ON_EMPTY makes quite a lot of work: a
host which is faster than the guest will fire the interrupt every xmit
packet (slowing the guest down further). Attempting mitigation in the
host adds overhead of userspace timers (possibly with the additional
pain of signals), and risks increasing latency anyway if you get it
wrong.
In practice, this effect was masked by benchmarks which take advantage
of GSO (with its inherent transmit batching), but it's still there.
Now we orphan xmitted skbs, the pressure is off: remove both paths and
no longer request VIRTIO_F_NOTIFY_ON_EMPTY. Note that the current
QEMU will notify us even if we don't negotiate this feature (legal,
but suboptimal); a patch is outstanding to improve that.
Move the skb_orphan/nf_reset to after we've done the send and notified
the other end, for a slight optimization.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mark McLoughlin <markmc@redhat.com>
|
|
This effectively reverts 99ffc696d10b28580fe93441d627cf290ac4484c
"virtio: wean net driver off NETDEV_TX_BUSY".
The complexity of queuing an skb (setting a tasklet to re-xmit) is
questionable, especially once we get rid of the other reason for the
tasklet in the next patch.
If the skb won't fit in the tx queue, just return NETDEV_TX_BUSY.
This is frowned upon, so a followup patch uses a more complex solution.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The complex transmit free logic was introduced to avoid hangs on
removing the ip_conntrack module and also because drivers aren't
generally supposed to keep stale skbs for unbounded times.
After some debate, it was decided that while doing skb_orphan()
generally is a rat's nest, we can do it in this driver. Following
patches take advantage of this.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Virtio IDs are spread all over the tree which makes assigning new IDs
bothersome. Putting them together should make the process less error-prone.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This API change means that virtio_net can tell how much capacity
remains for buffers. It's necessarily fuzzy, since
VIRTIO_RING_F_INDIRECT_DESC means we can fit any number of descriptors
in one, *if* we can kmalloc.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
|
|
No need to put ethtool_ops in data, they should be const.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/yellowfin.c
|
|
These are all drivers that don't touch real hardware.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we run out of memory, use keventd to fill the buffer. There's a
report of this happening: "Page allocation failures in guest",
Message-ID: <20090713115158.0a4892b0@mjolnir.ossman.eu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Allow setting UFO on virtio-net and advertise to host.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is inspired by patch recently posted by Johannes Berg. Basically what
my patch does is to group list and a count of addresses into newly introduced
structure netdev_hw_addr_list. This brings us two benefits:
1) struct net_device becames a bit nicer.
2) in the future there will be a possibility to operate with lists independently
on netdevices (with exporting right functions).
I wanted to introduce this patch before I'll post a multicast lists conversion.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 4 +-
drivers/net/e1000/e1000_main.c | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/mv643xx_eth.c | 2 +-
drivers/net/niu.c | 4 +-
drivers/net/virtio_net.c | 10 ++--
drivers/s390/net/qeth_l2_main.c | 2 +-
include/linux/netdevice.h | 17 +++--
net/core/dev.c | 130 ++++++++++++++++++--------------------
9 files changed, 89 insertions(+), 90 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6
Conflicts:
Documentation/feature-removal-schedule.txt
drivers/scsi/fcoe/fcoe.c
net/core/drop_monitor.c
net/core/net-traces.c
|
|
This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)
|
|
Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.
Also, add a "name" field for clearer debug messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
We need to enforce the IP alignment on the non-mergeable RX path just
like the other RX path. Not doing so results in misaligned IP
headers.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Through a bug in the tun driver, I noticed that virtio_net is
producing bogus hdr_len values. In particular, it only includes
the IP header in the linear area, and excludes the entire TCP
header. This causes the TCP header to be copied twice for each
packet. (The bug omitted the second copy :)
This patch corrects this.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch converts unicast address list to standard list_head using
previously introduced struct netdev_hw_addr. It also relaxes the
locking. Original spinlock (still used for multicast addresses) is not
needed and is no longer used for a protection of this list. All
reading and writing takes place under rtnl (with no changes).
I also removed a possibility to specify the length of the address
while adding or deleting unicast address. It's always dev->addr_len.
The convertion touched especially e1000 and ixgbe codes when the
change is not so trivial.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
drivers/net/bnx2.c | 13 +--
drivers/net/e1000/e1000_main.c | 24 +++--
drivers/net/ixgbe/ixgbe_common.c | 14 ++--
drivers/net/ixgbe/ixgbe_common.h | 4 +-
drivers/net/ixgbe/ixgbe_main.c | 6 +-
drivers/net/ixgbe/ixgbe_type.h | 4 +-
drivers/net/macvlan.c | 11 +-
drivers/net/mv643xx_eth.c | 11 +-
drivers/net/niu.c | 7 +-
drivers/net/virtio_net.c | 7 +-
drivers/s390/net/qeth_l2_main.c | 6 +-
drivers/scsi/fcoe/fcoe.c | 16 ++--
include/linux/netdevice.h | 18 ++--
net/8021q/vlan.c | 4 +-
net/8021q/vlan_dev.c | 10 +-
net/core/dev.c | 195 +++++++++++++++++++++++++++-----------
net/dsa/slave.c | 10 +-
net/packet/af_packet.c | 4 +-
18 files changed, 227 insertions(+), 137 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were avoiding calling sg_init* on scatterlists passed
into virtnet_send_command to prevent extraneous end markers.
This caused build warnings for uninitialized variables.
Cleanup the code to create proper scatterlists.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VIRTIO_NET_F_MAC indicates the presence of the mac field in config
space, not the validity of the value it contains. Allow the mac to be
changed at runtime, but only push the change into config space with the
VIRTIO_NET_F_MAC feature present.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/virtio_net.c
|
|
Impact: Make NetworkManager work with virtio_net
For now the semantics are simple: There is always carrier.
This allows a seamless experience with e.g., qemu/kvm
where NetworkManager just configures and sets up
everything automagically.
If/when a generally agreed-upon way to control
carrier on/off in the emulator/hypervisor level
emerges, it will be trivial to extend the driver
to support that too, but for now even this 2-liner
makes user experience that much better.
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many physical NICs let the OS re-program the "hardware" MAC
address. Virtual NICs should allow this too.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VLAN filtering allows the hypervisor to drop packets from VLANs
that we're not a part of, further reducing the number of extraneous
packets recieved. This makes use of the VLAN virtqueue command class.
The CTRL_VLAN feature bit tells us whether the backend supports VLAN
filtering.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the MAC control virtqueue class to support a MAC
filter table. The filter table is managed by the hypervisor.
We consider the table to be available if the CTRL_RX feature
bit is set. We leave it to the hypervisor to manage the table
and enable promiscuous or all-multi mode as necessary depending
on the resources available to it.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make use of the RX_MODE control virtqueue class to enable the
set_rx_mode netdev interface. This allows us to selectively
enable/disable promiscuous and allmulti mode so we don't see
packets we don't want. For now, we automatically enable these
as needed if additional unicast or multicast addresses are
requested.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will be used for RX mode, MAC filter table, VLAN filtering, etc...
The control transaction consists of one or more "out" sg entries and
one or more "in" sg entries. The first out entry contains a header
defining the class and command. Additional out entries may provide
data for the command. The last in entry provides a status response
back from the command.
Virtqueues typically run asynchronous, running a callback function
when there's data in the channel. We can't readily make use of this
in the command paths where we need to use this. Instead, we kick
the virtqueue and spin. The kick causes an I/O write, triggering an
immediate trap into the hypervisor.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/e1000/e1000_main.c
|
|
Without this fix, virtio_net makes incorrect usage of scatterlists. It sets
the end of the scatterlist chain after the first element, despite the fact
that more entries come after it.
If you try to run dma_map_sg() on one of the scatterlists given to you by
add_buf(), you will get a null pointer oops.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
|
|
802.1Q expanded the maximum ethernet frame size by 4 bytes for the
VLAN tag. We're not taking this into account in virtio_net, which
means the buffers we provide to the backend in the virtqueue RX ring
aren't big enough to hold a full MTU VLAN packet. For QEMU/KVM,
this results in the backend exiting with a packet truncation error.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the host to inform us that the link is down by adding
a VIRTIO_NET_F_STATUS which indicates that device status is
available in virtio_net config.
This is currently useful for simulating link down conditions
(e.g. using proposed qemu 'set_link' monitor command) but
would also be needed if we were to support device assignment
via virtio.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (added future masking)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't really have a max tx packet size limit, so allow configuring
the device with up to 64k tx MTU.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
If segmentation offload is enabled by the host, we currently allocate
maximum sized packet buffers and pass them to the host. This uses up
20 ring entries, allowing us to supply only 20 packet buffers to the
host with a 256 entry ring. This is a huge overhead when receiving
small packets, and is most keenly felt when receiving MTU sized
packets from off-host.
The VIRTIO_NET_F_MRG_RXBUF feature flag is set by hosts which support
using receive buffers which are smaller than the maximum packet size.
In order to transfer large packets to the guest, the host merges
together multiple receive buffers to form a larger logical buffer.
The number of merged buffers is returned to the guest via a field in
the virtio_net_hdr.
Make use of this support by supplying single page receive buffers to
the host. On receive, we extract the virtio_net_hdr, copy 128 bytes of
the payload to the skb's linear data buffer and adjust the fragment
offset to point to the remaining data. This ensures proper alignment
and allows us to not use any paged data for small packets. If the
payload occupies multiple pages, we simply append those pages as
fragments and free the associated skbs.
This scheme allows us to be efficient in our use of ring entries
while still supporting large packets. Benchmarking using netperf from
an external machine to a guest over a 10Gb/s network shows a 100%
improvement from ~1Gb/s to ~2Gb/s. With a local host->guest benchmark
with GSO disabled on the host side, throughput was seen to increase
from 700Mb/s to 1.7Gb/s.
Based on a patch from Herbert Xu.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use netdev_priv)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Seems like an oversight that we have set-tx-csum and set-sg hooked
up, but not set-tso.
Also leads to the strange situation that if you e.g. disable tx-csum,
then tso doesn't get disabled.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each time we re-fill the recv queue with buffers, we allocate
one too many skbs and free it again when adding fails. We should
recycle the pages allocated in this case.
A previous version of this patch made trim_pages() trim trailing
unused pages from skbs with some paged data, but this actually
caused a barely measurable slowdown.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (use netdev_priv)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.
This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we hack the virtio_net driver to always allocate full-sized (64k+)
skbuffs, the driver slows down (lguest numbers):
Time to receive 1GB (small buffers): 10.85 seconds
Time to receive 1GB (64k+ buffers): 24.75 seconds
Of course, large buffers use up more space in the ring, so we increase
that from 128 to 2048:
Time to receive 1GB (64k+ buffers, 2k ring): 16.61 seconds
If we recycle pages rather than using alloc_page/free_page:
Time to receive 1GB (64k+ buffers, 2k ring, recycle pages): 10.81 seconds
This demonstrates that with efficient allocation, we don't need to
have a separate "small buffer" queue.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Finally this patch lets virtio_net receive GSO packets in addition
to sending them. This can definitely be optimised for the non-GSO
case. For comparison the Xen approach stores one page in each skb
and uses subsequent skb's pages to construct an SG skb instead of
preallocating the maximum amount of pages per skb.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (added feature bits)
|
|
This patch adds some basic ethtool operations to virtio_net so
I could test SG without GSO (which was really useful because TSO
turned out to be buggy :)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (remove MTU setting)
|
