| Age | Commit message (Collapse) | Author |
|---|
|
ACX_PEER_CAP command is just ACX_PEER_HT_CAP, but allows
configuring the peer's support rates as well.
this is needed because we start the station role when
the remote rates are not known yet.
the two commands should be unified in future fw versions,
but for now add a new set_peer_cap per-hw op, that will
use ACX_PEER_CAP for 18xx, and ACX_PEER_HT_CAP for 12xx.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
This allows us to pass only the link as a parameter to various functions
and deduce the wlvif. Note that this member will be NULL for global
links.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
When a link is allocated, sometimes the "freed packets" counter in FW
is non zero, but we always assumed it is. This caused us to incorrectly
account FW allocated blocks in some cases.
When operating in AP mode, this bug caused some stations to never
come back from PSM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Make sure free_link is always called when removing an interface. This
ensures all skbs belonging to this interface are returned to mac80211.
Otherwise these dangling skbs might crash the system on the next
call to wl1271_tx_reset_link_queues(). This happens on recovery/stop or
an unsuccessful Tx flush.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Currently, each fw command/acx that return a status code
different than CMD_STATUS_SUCCESS will trigger a recovery
in the driver.
However, it is a valid for some fw commands to fail (e.g.
due to temporary lack of resources), so add new functions
that allow passing bitmap of valid error return values.
(make the current wl1271_cmd_send/wl1271_cmd_configure
wrappers around the new functions, in order to avoid
changing the whole driver)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
mask out CCK rates from the AP's local rates
when the interace is p2p interface (GO).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
We support changing the channel BW when we started the STA role on
a 40Mhz bandwidth. Otherwise a reconnection is required.
Save the started channel width and use it when channel width updates
arrive.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In 18xx the calibration process of the PHY Cortex domain
requires to perform an active calibration of the channel
before it can be used for transmission. To fulfill world
wide regulatory restrictions, fw should be always
synchronized/updated with current CRDA configuration.
Add a new "CMD_DFS_CHANNEL_CONFIG" command to update the
fw with current reg-domain, this command passes a bit map
of channels that are allowed to be used for transmission.
The driver shall update the fw during initialization and
after each change in the current reg-domain
configuration. The driver will save the channel number of
incoming beacons during the scan process, as they might
be a result of the passive scan on
"IEEE80211_CHAN_PASSIVE_SCAN" channel and will update the
fw accordingly once the scan is finished, the purpose of
this is to be ready in case of the authentication request
on one of these disabled (uncalibrated) channels.
The new command requires to wait for the fw completion
event "DFS_CHANNELS_CONFIG_COMPLETE_EVENT".
No scan commands (including the sched scan) can be
executed concurrently with the "CMD_DFS_CHANNEL_CONFIG",
wl->mutex ensures that.
[Arik - move reset of reg_ch_conf_last to safe place inside
op_stop_locked]
[Eliad - adjust to new event waiting api]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
A new session_id is generated on link allocation.
it is saved in a global array and used later, on tx.
The new fw api adds new bcast/global_session_id
fields to start_role(ap) command, and a new session_id
field to add_peer command. align the driver with it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
New fields were added to start_role(ap) and
set_peer_state commands, so the fw will be
able to know whether the sta/ap supports
wmm (the fw uses it in order to choose the
AC for some of its internally-generated frames)
For sta, take this value right from bss_conf->qos.
For ap, check for wmm support by looking for the
WMM IE in the configured beacon.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The event mailbox in wl18xx has a different
(non-compatible) structure.
Create common functions in wlcore to handle the
events, and call them from the chip-specific
event mailbox parsers.
This way, each driver (wl12xx/wl18xx) extracts
the event mailbox by itself according to its
own structure, and then calls the common
wlcore functions to handle it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Some fields were added to the channel_switch and
stop_channel_switch commands. Unfortunately,
the new 18xx channel_switch struct is not backward
compatible with the 12xx channel switch struct.
Add a new channel_switch op to wlcore, and update
the driver accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The scan APIs of 12xx and 18xx are totally different.
Use some common functions as much as possible (e.g.
for setting scan channels), but split scan.c into
chip-specific scan.c files, each implementing its
own scan mechanism.
(in other words - move most of the current wlcore's
scan.c into wl12xx, and implement a similar mechanism
in 18xx, according to the new api)
New wlcore ops are introduced in order to call the
chip-specific scan functions.
The template indices used for each scan (regular/scheduled)
are also different between the chips, so set the correct
indices used for each scan type after identifying the chip.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
With the new connection flow, start_sta is called before
the remote rates where updated. Use our own supported rates
instead to make sure we don't disable any potential rate
(the rate policies will be updated later, but there is
currently no way to update the remote rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.
(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
implement the reamin_on_channel() callback by starting
a dev role (already associated with the current vif)
on the requested channel/band.
This channel is usually different from the channel
of the sta role, so pass it to wl12xx_roc() as well,
and notify mac80211 (async) when the fw is ready
on the new channel.
Now, in case of offchannel tx, we should use the dev
role hlid, instead of the sta hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Currently, all the (station) roles use the same
keep-alive template id (0). However, the klv
template ids shouldn't be shared by different
roles.
Implement a simple klv_templates bitmap, and let
each role allocate its own klv template id on
role initialization.
[Arik - remove invalidation of KLV template when getting into "idle".
This is already handled in unjoin]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Enable device roles just before starting it.
This way, a single device role should be enough
for all vifs, as we can't use concurrent device
roles (which require ROC) anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
When a function requests to recover, it would normally abort and will
not send any additional commands to the HW. However, other threads may
not be aware of the failure and could try to communicate with the HW
after a recovery was queued, but before the recovery work began.
Fix this by introducing an intermediate state which is set when recovery
is queued, and modify all state checks accordingly.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
We need to wait for the command completion event when we send the
CMD_ROLE_STOP event otherwise we may try to send CMD_ROLE_START too
soon and get out-of-sync with the firmware.
In some cases, the firmware may not send the event, so we wait for the
event or for the timeout, whichever comes first.
This patch is based on an earlier version by Eliad.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
wlcore needs to wait for certain events for example
for roc complete event. Usually the events are received
from the FW very fast, therefore wlcore can poll with
a short delay and if after a second the event was
not received yet poll with a long (1-5 msec) delay.
This implementation is similar to the sending of
commands to the FW.
Empirically the change reduced the wait for roc event
from ~10-40msec to 100s of usecs.
[replace udelay/msleep with usleep_range - Arik]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
|
|
The driver configures the firmware template for probe requests during
the scan process. If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.
This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.
[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
As recovery queuing can now occur from multiple code paths
it's convenient to know what triggered it in all cases
other than an intended recovery which is part of the
switch between single role to multi role.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Following the addition of propagating errors from the bus ops
there's a need to distinguish between bus errors (including timeout)
and a legitimate timeout occuring in cmd_wait_for_event_or_timeout.
In case of real bus errors we need to queue recovery even in cases
where a timeout on a response from the FW to a command is acceptable.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Propagate errors from wl1271_raw_write32 and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Propagate errors from wl1271_raw_read32. Since the read functions had no
way of returning errors in-band, change their prototypes.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Propagate errors from wl1271_write and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Propagate errors from wl1271_read and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
18xx chips do not require extra space in the TKIP header. Introduce a
new HW quirk to allow us to make this feature arch-specific. 12xx chip
will now have this quirk.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In some multi role scenarios the driver might send multi
roc requests without sending a croc first, the fw queues
those requests and starts service the next roc request as
soon as the driver sends a croc for the previous one. So,
if the fw rocs on channel X and driver asks to roc also
on channel Y, the fw will not start service Y (and will
not send roc complete event for this request) until the
driver releases the fw with croc X.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In ieee80211.h the uapsd bit mask is defined such that
VO=BIT(0), VI=BIT(1), BK=BIT(2), BE=BIT(3).
The firmware uses the indexing as defined in the ieee80211
spec, meaning that VO=3, VI=2, BK=1, BE=0.
In AP mode when adding peer wlcore needs to convert
the indexing accordingly.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
We were setting all the rates bits when starting the AP role. Instead
of doing this, we should set only the rates we really support
(eg. MIMO rates or wide-channel rates). This commit changes that so
that we always use the default rates (basic rates + MCS0-7) and add
the values returned by the ap_get_mimo_wide_rate_mask operation.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
|
|
PLT mode needs to be initialized differently for each chip. This
patch adds an operation to init PLT and moves the existing PLT
initialization into the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
|
|
Parse the peer ht_cap element containing MCS8-MCS15 rates and pass it
to the FW. Rates unsupported by the HW will be sanitized by mac80211
before reaching us.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Translate the NL80211 channel type to a FW-specific channel type and send
it to the FW as part of the role-start command. For wl12xx this has no
effect - this element is treated as padding.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
We currently do this:
int wl1271_cmd_build_arp_rsp(struct wl1271 *wl, struct wl12xx_vif *wlvif)
...
struct wl12xx_arp_rsp_template *tmpl;
struct ieee80211_hdr_3addr *hdr;
...
tmpl = (struct wl12xx_arp_rsp_template *)skb_put(skb, sizeof(*tmpl));
memset(tmpl, 0, sizeof(tmpl));
...
hdr = (struct ieee80211_hdr_3addr *)skb_push(skb, sizeof(*hdr));
memset(hdr, 0, sizeof(hdr));
...
I believe we want to set the entire structures to 0 with those
memset() calls, not just zero the initial part of them (size of the
pointer bytes).
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
GFP_DMA isn't supposed to be used by itself. This allocation is allowed
to sleep so it should be ORing it with GFP_KERNEL.
Also we should check for allocations errors.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Change the cmd_trigger op to include the write of the command buffer.
Also, instead of letting the lower driver access the cmd_box_addr element
directly, we now pass the address in the trigger_cmd operation, so it
doesn't have to be exported.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Move all the wl12xx-specific hw initialization procedures into a new
hw_init op. Move some commands and ACX functions to wl12xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Different chips may use different bits in the interrupt trigger
register. Add operations to handle these differences.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Add register tables support in wlcore, add some new IO functions to
read and write to chip-specific register and data addresses. Move
some common register values from wl12xx to wlcore and add the
registers table to wl12xx.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
In order to add chip-specific operations and prepare for future
elements that need to be set by the lower driver, move the wl1271
structure to the wlcore.h file and add an empty placeholder for the
operations structure.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Rename the wl12xx driver directory to wlcore as an initial step
towards the split of the driver into wlcore and wl12xx. We just
rename the directory first to keep git blame happy.
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
