| Age | Commit message (Collapse) | Author |
|---|
|
commit 9795229752c31da0c5f8a7dc4c827665327b52f9 upstream.
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f699273d6a624266ebc9198774f06ee64a3847a1 upstream.
The static analyser "cppcheck" shows the following typo:
drivers/net/wireless/rtlwifi/rtl8188ee/dm.c:1081]: (style) Same expression on both sides of '!='.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: David Binderman <dcb314@hotmail.com>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d82403a9f407217b6aed5260aa92a120e8e98310 upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit e9b0784bb9de3152e787ee779868c626b137fb3b upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9806eacf5de27ab01d680c5d75c92a3a89734e4f upstream.
This patch uses the newly introduced power index register routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 97204e93f01868eeba6ae5c4f3270f32905bb418 upstream.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dc6405712268fe514d3dd89aa936c4397b0871b9 upstream.
The current number of RX buffers queued is 32, which is too small under
heavy load. That number is doubled.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit c908c74e005de780fddbe8cb6fcd44803f5d4b74 upstream.
Changes in the gain-control mechanism will require some changes in the header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 619ce76f8bb850b57032501a39f26aa6c6731c70 upstream.
The present code fails to set the linked state when an interface is
added.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b9a758a8c905fc59e783ae91ad645452d877ea88 upstream.
The initial USB driver did not use some register save locations in the
private data storage. To save some memory, a union was used to overlay these
variables with USB I/O components. In an update of the gain-control code,
these register save locations are now needed for USB drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 62009b7f12793c932aaba0df946b04cb4a77d022 upstream.
Vendor driver rtl8188C_8192C_8192D_usb_linux_v3.4.2_3727.20120404 introduced
new firmware for these chips. The code try for the new file, and fall back to
the original firmware if the new file is not available.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8fd77aec1a9d6f4328fc0244f21932114e066df3 upstream.
This driver has a watchdog timer that attempts to reconnect when beacon frames
are not seen for 6 seconds. This patch disables that reconnect whenever the
device has never been connected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 65b9cc97c6852fae19dc5c7745e9abc8dd380aad upstream.
The USB drivers were not updating the beacon statistics, which led to
false beacon loss indications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f87f960b2fb802f26ee3b00c19320e57a9c583ff upstream.
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 9278db6279e28d4d433bc8a848e10b4ece8793ed upstream.
On Fedora systems, unloading rtl8192ce causes an oops. This patch fixes the
problem reported at https://bugzilla.redhat.com/show_bug.cgi?id=852761.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 657eb17d87852c42b55c4b06d5425baa08b2ddb3 upstream.
Pick the MAC address of the first virtual interface as the new hardware MAC
address. Set BSSID mask according to this MAC address. This fixes CVE-2013-4579.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 73f0b56a1ff64e7fb6c3a62088804bab93bcedc2 upstream.
This patch adds a driver workaround for a HW issue.
A race condition in the HW results in missing interrupts,
which can be avoided by a read/write with the ISR register.
All chips in the AR9002 series are affected by this bug - AR9003
and above do not have this problem.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 517543fd72d577dde2ebd9505dc4abf26d589f9a upstream.
For IBSS join if the requested SSID matches current SSID,
it returns without freeing the allocated beacon IE buffer.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 60765a47a433d54e4744c285ad127f182dcd80aa upstream.
The station ID must be valid, if it's out of range then
the array access may crash. Validate the station ID to
the array length, and also validate the drain value even
if that doesn't matter all that much.
Fixes: 8ca151b568b6 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit bbf807bc0697e577c137a5fffb30fca7c6a45da1 upstream.
When not aggregating packets, fi->framelen should be passed in as length
to calculate the duration. Before the tx path rework, ath_tx_fill_desc
was called for either one aggregate, or one single frame, with the
length of the packet or the aggregate as a parameter.
After the rework, ath_tx_sched_aggr can pass a burst of single frames to
ath_tx_fill_desc and sets len=0.
Fix broken duration calculation by overriding the length in ath_tx_fill_desc
before passing it to ath_buf_set_rate.
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a1783a7b0846fc6414483e6caf646db72023fffd upstream.
The EEPROM parameter to determine whether the bias
strength values for XLNA have to be applied is part
of the miscConfiguration field and not featureEnable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 93c1cfbe598f72cfa7be49e4a7d2a1d482e15119 upstream.
Bit 5 in the miscConfiguration field of the base EEPROM
header denotes whether QuickDrop is enabled or not. Fix
the incorrect usage of BIT(1) and also make sure that
this is done only for the required chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 6960a059b2c618f32fe549f13287b3d2278c09e9 upstream.
We changed the timeout for the interrupt coealescing for
calibration, but that wasn't effective since we changed
that value back before loading the firmware. Since
calibrations are notification from firmware and not Rx
packets, this doesn't change anyway - the firmware will
fire an interrupt straight away regardless of the interrupt
coalescing value.
Also, a HW issue has been discovered in 7000 devices series.
The work around is to disable the new interrupt coalescing
timeout feature - do this by setting bit 31 in
CSR_INT_COALESCING.
This has been fixed in 7265 which means that we can't rely
on the device family and must have a hint in the iwl_cfg
structure.
Fixes: 99cd47142399 ("iwlwifi: add 7000 series device configuration")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit f6b129527ca15bae29ffb9417ddaa1c9d99ffc5d upstream.
Since we set IEEE80211_HW_QUEUE_CONTROL, we can let
mac80211 do the queue assignement and don't need to
override its decisions.
While reassiging the same values is harmless of course,
it triggered a WARNING when iwlwifi and mac80211 came
to different conclusions. This happened when mac80211 set
IEEE80211_TX_CTL_SEND_AFTER_DTIM, but didn't route the
packet to the cab_queue because no stations were asleep.
iwlwifi should not override mac80211's decicions for
offchannel packets and packets to be sent after DTIM,
but it should override mac80211's decision for AMPDUs
since we have a special queue for them. So for AMPDU,
we still override info->hw_queue by the AMPDU queue.
This avoids:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 2531 at drivers/net/wireless/iwlwifi/dvm/tx.c:456 iwlagn_tx_skb+0x6c5/0x883()
Modules linked in:
CPU: 0 PID: 2531 Comm: hostapd Not tainted 3.12.0-rc5+ #1
Hardware name: /D53427RKE, BIOS RKPPT10H.86A.0017.2013.0425.1251 04/25/2013
0000000000000000 0000000000000009 ffffffff8189aa62 0000000000000000
ffffffff8105a4f2 ffff880058339a48 ffffffff815f8a04 0000000000000000
ffff8800560097b0 0000000000000208 0000000000000000 ffff8800561a9e5e
Call Trace:
[<ffffffff8189aa62>] ? dump_stack+0x41/0x51
[<ffffffff8105a4f2>] ? warn_slowpath_common+0x78/0x90
[<ffffffff815f8a04>] ? iwlagn_tx_skb+0x6c5/0x883
[<ffffffff815f8a04>] ? iwlagn_tx_skb+0x6c5/0x883
[<ffffffff818a0040>] ? put_cred+0x15/0x15
[<ffffffff815f6db4>] ? iwlagn_mac_tx+0x19/0x2f
[<ffffffff8186cc45>] ? __ieee80211_tx+0x226/0x29b
[<ffffffff8186e6bd>] ? ieee80211_tx+0xa6/0xb5
[<ffffffff8186e98b>] ? ieee80211_monitor_start_xmit+0x1e9/0x204
[<ffffffff8171ce5f>] ? dev_hard_start_xmit+0x271/0x3ec
[<ffffffff817351ac>] ? sch_direct_xmit+0x66/0x164
[<ffffffff8171d1bf>] ? dev_queue_xmit+0x1e5/0x3c8
[<ffffffff817fac5a>] ? packet_sendmsg+0xac5/0xb3d
[<ffffffff81709a09>] ? sock_sendmsg+0x37/0x52
[<ffffffff810f9e0c>] ? __do_fault+0x338/0x36b
[<ffffffff81713820>] ? verify_iovec+0x44/0x94
[<ffffffff81709e63>] ? ___sys_sendmsg+0x1f1/0x283
[<ffffffff81140a73>] ? __inode_wait_for_writeback+0x67/0xae
[<ffffffff8111735e>] ? __cache_free.isra.46+0x178/0x187
[<ffffffff811173b1>] ? kmem_cache_free+0x44/0x84
[<ffffffff81132c22>] ? dentry_kill+0x13d/0x149
[<ffffffff81132f6f>] ? dput+0xe5/0xef
[<ffffffff81136e04>] ? fget_light+0x2e/0x7c
[<ffffffff8170ae62>] ? __sys_sendmsg+0x39/0x57
[<ffffffff818a7e39>] ? system_call_fastpath+0x16/0x1b
---[ end trace 1b3eb79359c1d1e6 ]---
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3b9b74baa1af2952d719735b4a4a34706a593948 upstream.
Add support for new RF chip ID: 3070. It seems to be the same as 5370,
maybe vendor just put wrong value on the eeprom, but add this id anyway
since devices with it showed on the marked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8e3ffa471091c560deb6738ed9ab7445b7a5fd04 upstream.
Userspace uses the netdev devtype for stuff like device naming and type
detection. Be nice and set it. Remove the pointless #if/#endif around
SET_NETDEV_DEV too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 8d93f1f309d38b65fce0b9f0de91ba6c96990c07 upstream.
The eth_hdr is never defined in this driver but it gets compiled
without any warning/error because kernel has defined eth_hdr.
Fix it by defining our own p_ethhdr and use it instead of eth_hdr.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit d03b4aa77e1187b77dfe37d14a923547f00baa66 upstream.
While receiving a packet on SDIO interface, we allocate skb with
size multiple of SDIO block size. We need to resize this skb
after RX using packet length from RX header.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 2bf127a5cc372b9319afcbae10b090663b621c8b upstream.
RSSI value is provided on word3 not on word2.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 7ede612fd615abcda0cc30e5bef2a70f4cf4f75c upstream.
The regression was introduced in the following commit:
0967e01e8e713ed2982fb4eba8ba13794e9a6e89
"ath5k: make use of the new rate control API"
ath5k_tx_frame_completed saves the intended per-rate retry counts before
they are cleared by ieee80211_tx_info_clear_status, however at this
point the information in info->status.rates is incomplete.
This causes significant throughput degradation and excessive packet loss
on links where high bit rates don't work properly.
Move the copy from bf->rates a few lines up to ensure that the saved
retry counts are updated, and that they are really cleared in
info->status.rates after the call to ieee80211_tx_info_clear_status.
Cc: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Cc: Benjamin Vahl <bvahl@net.t-labs.tu-berlin.de>
Reported-by: Ben West <ben@gowasabi.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 78dbfecb95be4635b995af3bd29fa10013409fcd upstream.
The routine that processes received frames was returning the RSSI value for the
signal strength; however, that value is available only for associated APs. As
a result, the strength was the absurd value of 10 dBm. As a result, scans
return incorrect values for the strength, which causes unwanted attempts to roam.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4ade797668e33b4e8353c2701ce01d7084dfafa upstream.
The routine that processes received frames was returning the RSSI value for the
signal strength; however, that value is available only for associated APs. As
a result, the strength was the absurd value of 10 dBm. As a result, scans
return incorrect values for the strength, which causes unwanted attempts to roam.
This patch fixes https://bugzilla.kernel.org/show_bug.cgi?id=63881.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Matthieu Baerts <matttbe@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3545f3d5f4af715c914394123ce7725a9cf0a1c4 upstream.
The routine that processes received frames was returning the RSSI value for the
signal strength; however, that value is available only for associated APs. As
a result, the strength was the absurd value of 10 dBm. As a result, scans
return incorrect values for the strength, which causes unwanted attempts to roam.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit eafbdde9c5629bea58df07275c5917eb42afbbe7 upstream.
This driver uses a number of macros to get and set various fields in the
RX and TX descriptors. To work correctly, a u8 pointer to the descriptor
must be used; however, in some cases a descriptor structure pointer is used
instead. In addition, a duplicated statement is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3aef7dde8dcf09e0124f0a2665845a507331972b upstream.
There is a typo in the struct member name on assignment when checking
rtlphy->current_chan_bw == HT_CHANNEL_WIDTH_20_40, the check uses pwrgroup_ht40
for bound limit and uses pwrgroup_ht20 when assigning instead.
Signed-off-by: Felipe Pena <felipensp@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0c5d63f0ab6728f05ddefa25aff55e31297f95e6 upstream.
All of the rtlwifi drivers have an error in the routine that tests if
the data is "special". If it is, the subsequant transmission will be
at the lowest rate to enhance reliability. The 16-bit quantity is
big-endian, but was being extracted in native CPU mode. One of the
effects of this bug is to inhibit association under some conditions
as the TX rate is too high.
Based on suggestions by Joe Perches, the entire routine is rewritten.
One of the local headers contained duplicates of some of the ETH_P_XXX
definitions. These are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit dab3df5e88b979f8d09860f873ccfaa7a55758d2 upstream.
Smatch lists the following:
CHECK drivers/net/wireless/rtlwifi/rtl8188ee/hw.c
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c:149 _rtl88ee_set_fw_clock_on() info: ignoring unreachable code.
This info message is the result of a real error due to a missing break statement
in a "while (1)" loop.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 36165fd5b00bf8163f89c21bb16a3e9834555b10 upstream.
Polling TX statuses too frequently has two negative effects. First is
randomly peek CPU usage, causing overall system functioning delays.
Second bad effect is that device is not able to fill TX statuses in
H/W register on some workloads and we get lot of timeouts like below:
ieee80211 phy4: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 7 in queue 2
ieee80211 phy4: rt2800usb_entry_txstatus_timeout: Warning - TX status timeout for entry 7 in queue 2
ieee80211 phy4: rt2800usb_txdone: Warning - Got TX status for an empty queue 2, dropping
This not only cause flood of messages in dmesg, but also bad throughput,
since rate scaling algorithm can not work optimally.
In the future, we should probably make polling interval be adjusted
automatically, but for now just increase values, this make mentioned
problems gone.
Resolve:
https://bugzilla.kernel.org/show_bug.cgi?id=62781
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 3d8bfe141be8e5c21261fc63da8e7964d44f2645 upstream.
Since:
commit 36323f817af0376c78612cfdab714b0feb05fea5
Author: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Date: Mon Jul 23 21:33:42 2012 +0200
mac80211: move TX station pointer and restructure TX
we do not pass sta pointer to rt2x00queue_create_tx_descriptor_ht(),
hence we do not correctly set station WCID and AMPDU density parameters.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 0beb1bbf19c72f17809e42b8f33522a55c2cc18c upstream.
In commit 3d81535ea5940446510a8a5cee1c6ad23c90c753
(rt2800: 5592: add chip specific vgc calculations)
the rt2800_link_tuner function has been modified to
adjust VGC level for the RT5592 chipset.
On the RT5592 chipset, the VGC level must be adjusted
only if rssi is greater than -65. However the current
code adjusts the VGC value by 0x10 regardless of the
actual chipset if the rssi value is between -80 and
-65.
Fix the broken behaviour by reordering the if-else
statements.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit 5671ab05cf2a579218985ef56595387932d78ee4 upstream.
Fix random kernel panic with below messages when remove dongle.
[ 2212.355447] BUG: unable to handle kernel NULL pointer dereference at 0000000000000250
[ 2212.355527] IP: [<ffffffffa02667f2>] rt2x00usb_kick_tx_entry+0x12/0x160 [rt2x00usb]
[ 2212.355599] PGD 0
[ 2212.355626] Oops: 0000 [#1] SMP
[ 2212.355664] Modules linked in: rt2800usb rt2x00usb rt2800lib crc_ccitt rt2x00lib mac80211 cfg80211 tun arc4 fuse rfcomm bnep snd_hda_codec_realtek snd_hda_intel snd_hda_codec btusb uvcvideo bluetooth snd_hwdep x86_pkg_temp_thermal snd_seq coretemp aesni_intel aes_x86_64 snd_seq_device glue_helper snd_pcm ablk_helper videobuf2_vmalloc sdhci_pci videobuf2_memops videobuf2_core sdhci videodev mmc_core serio_raw snd_page_alloc microcode i2c_i801 snd_timer hid_multitouch thinkpad_acpi lpc_ich mfd_core snd tpm_tis wmi tpm tpm_bios soundcore acpi_cpufreq i915 i2c_algo_bit drm_kms_helper drm i2c_core video [last unloaded: cfg80211]
[ 2212.356224] CPU: 0 PID: 34 Comm: khubd Not tainted 3.12.0-rc3-wl+ #3
[ 2212.356268] Hardware name: LENOVO 3444CUU/3444CUU, BIOS G6ET93WW (2.53 ) 02/04/2013
[ 2212.356319] task: ffff880212f687c0 ti: ffff880212f66000 task.ti: ffff880212f66000
[ 2212.356392] RIP: 0010:[<ffffffffa02667f2>] [<ffffffffa02667f2>] rt2x00usb_kick_tx_entry+0x12/0x160 [rt2x00usb]
[ 2212.356481] RSP: 0018:ffff880212f67750 EFLAGS: 00010202
[ 2212.356519] RAX: 000000000000000c RBX: 000000000000000c RCX: 0000000000000293
[ 2212.356568] RDX: ffff8801f4dc219a RSI: 0000000000000000 RDI: 0000000000000240
[ 2212.356617] RBP: ffff880212f67778 R08: ffffffffa02667e0 R09: 0000000000000002
[ 2212.356665] R10: 0001f95254ab4b40 R11: ffff880212f675be R12: ffff8801f4dc2150
[ 2212.356712] R13: 0000000000000000 R14: ffffffffa02667e0 R15: 000000000000000d
[ 2212.356761] FS: 0000000000000000(0000) GS:ffff88021e200000(0000) knlGS:0000000000000000
[ 2212.356813] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 2212.356852] CR2: 0000000000000250 CR3: 0000000001a0c000 CR4: 00000000001407f0
[ 2212.356899] Stack:
[ 2212.356917] 000000000000000c ffff8801f4dc2150 0000000000000000 ffffffffa02667e0
[ 2212.356980] 000000000000000d ffff880212f677b8 ffffffffa03a31ad ffff8801f4dc219a
[ 2212.357038] ffff8801f4dc2150 0000000000000000 ffff8800b93217a0 ffff8801f49bc800
[ 2212.357099] Call Trace:
[ 2212.357122] [<ffffffffa02667e0>] ? rt2x00usb_interrupt_txdone+0x90/0x90 [rt2x00usb]
[ 2212.357174] [<ffffffffa03a31ad>] rt2x00queue_for_each_entry+0xed/0x170 [rt2x00lib]
[ 2212.357244] [<ffffffffa026701c>] rt2x00usb_kick_queue+0x5c/0x60 [rt2x00usb]
[ 2212.357314] [<ffffffffa03a3682>] rt2x00queue_flush_queue+0x62/0xa0 [rt2x00lib]
[ 2212.357386] [<ffffffffa03a2930>] rt2x00mac_flush+0x30/0x70 [rt2x00lib]
[ 2212.357470] [<ffffffffa04edded>] ieee80211_flush_queues+0xbd/0x140 [mac80211]
[ 2212.357555] [<ffffffffa0502e52>] ieee80211_set_disassoc+0x2d2/0x3d0 [mac80211]
[ 2212.357645] [<ffffffffa0506da3>] ieee80211_mgd_deauth+0x1d3/0x240 [mac80211]
[ 2212.357718] [<ffffffff8108b17c>] ? try_to_wake_up+0xec/0x290
[ 2212.357788] [<ffffffffa04dbd18>] ieee80211_deauth+0x18/0x20 [mac80211]
[ 2212.357872] [<ffffffffa0418ddc>] cfg80211_mlme_deauth+0x9c/0x140 [cfg80211]
[ 2212.357913] [<ffffffffa041907c>] cfg80211_mlme_down+0x5c/0x60 [cfg80211]
[ 2212.357962] [<ffffffffa041cd18>] cfg80211_disconnect+0x188/0x1a0 [cfg80211]
[ 2212.358014] [<ffffffffa04013bc>] ? __cfg80211_stop_sched_scan+0x1c/0x130 [cfg80211]
[ 2212.358067] [<ffffffffa03f8954>] cfg80211_leave+0xc4/0xe0 [cfg80211]
[ 2212.358124] [<ffffffffa03f8d1b>] cfg80211_netdev_notifier_call+0x3ab/0x5e0 [cfg80211]
[ 2212.358177] [<ffffffff815140f8>] ? inetdev_event+0x38/0x510
[ 2212.358217] [<ffffffff81085a94>] ? __wake_up+0x44/0x50
[ 2212.358254] [<ffffffff8155995c>] notifier_call_chain+0x4c/0x70
[ 2212.358293] [<ffffffff81081156>] raw_notifier_call_chain+0x16/0x20
[ 2212.358361] [<ffffffff814b6dd5>] call_netdevice_notifiers_info+0x35/0x60
[ 2212.358429] [<ffffffff814b6ec9>] __dev_close_many+0x49/0xd0
[ 2212.358487] [<ffffffff814b7028>] dev_close_many+0x88/0x100
[ 2212.358546] [<ffffffff814b8150>] rollback_registered_many+0xb0/0x220
[ 2212.358612] [<ffffffff814b8319>] unregister_netdevice_many+0x19/0x60
[ 2212.358694] [<ffffffffa04d8eb2>] ieee80211_remove_interfaces+0x112/0x190 [mac80211]
[ 2212.358791] [<ffffffffa04c585f>] ieee80211_unregister_hw+0x4f/0x100 [mac80211]
[ 2212.361994] [<ffffffffa03a1221>] rt2x00lib_remove_dev+0x161/0x1a0 [rt2x00lib]
[ 2212.365240] [<ffffffffa0266e2e>] rt2x00usb_disconnect+0x2e/0x70 [rt2x00usb]
[ 2212.368470] [<ffffffff81419ce4>] usb_unbind_interface+0x64/0x1c0
[ 2212.371734] [<ffffffff813b446f>] __device_release_driver+0x7f/0xf0
[ 2212.374999] [<ffffffff813b4503>] device_release_driver+0x23/0x30
[ 2212.378131] [<ffffffff813b3c98>] bus_remove_device+0x108/0x180
[ 2212.381358] [<ffffffff813b0565>] device_del+0x135/0x1d0
[ 2212.384454] [<ffffffff81417760>] usb_disable_device+0xb0/0x270
[ 2212.387451] [<ffffffff8140d9cd>] usb_disconnect+0xad/0x1d0
[ 2212.390294] [<ffffffff8140f6cd>] hub_thread+0x63d/0x1660
[ 2212.393034] [<ffffffff8107c860>] ? wake_up_atomic_t+0x30/0x30
[ 2212.395728] [<ffffffff8140f090>] ? hub_port_debounce+0x130/0x130
[ 2212.398412] [<ffffffff8107baa0>] kthread+0xc0/0xd0
[ 2212.401058] [<ffffffff8107b9e0>] ? insert_kthread_work+0x40/0x40
[ 2212.403639] [<ffffffff8155de3c>] ret_from_fork+0x7c/0xb0
[ 2212.406193] [<ffffffff8107b9e0>] ? insert_kthread_work+0x40/0x40
[ 2212.408732] Code: 24 58 08 00 00 bf 80 00 00 00 e8 3a c3 e0 e0 5b 41 5c 5d c3 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41 55 41 54 53 <48> 8b 47 10 48 89 fb 4c 8b 6f 28 4c 8b 20 49 8b 04 24 4c 8b 30
[ 2212.414671] RIP [<ffffffffa02667f2>] rt2x00usb_kick_tx_entry+0x12/0x160 [rt2x00usb]
[ 2212.417646] RSP <ffff880212f67750>
[ 2212.420547] CR2: 0000000000000250
[ 2212.441024] ---[ end trace 5442918f33832bce ]---
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit b4089d6d8e71a7293e2192025dfa507a04f661c4 upstream.
Commit "rt2x00: fix HT TX descriptor settings regression"
assumes that the control parameter to rt2x00mac_tx is always non-NULL.
There is an internal call in rt2x00lib_bc_buffer_iter where NULL is
passed. Fix the resulting crash by adding an initialized dummy on-stack
ieee80211_tx_control struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a497e47d4aec37aaf8f13509f3ef3d1f6a717d88 upstream.
If we do a zero size allocation then it will oops. Also we can't be
sure the user passes us a NUL terminated string so I've added a
terminator.
This code can only be triggered by root.
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
|
|
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Free temporary 'chanspecs' avoiding leakage.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
|
|
This driver uses a number of macros to get and set various fields in the
RX and TX descriptors. To work correctly, a u8 pointer to the descriptor
must be used; however, in some cases a descriptor structure pointer is used
instead. In addition, a duplicated statement is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
1) After driver load failure, clear 'card->adapter' instead of
card pointer so that card specific cleanup is performed later
when user unloads the driver.
2) Clear usb_card pointer in disconnect handler to avoid invalid
memory access when user unloads the driver after removing the
card.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
