| Age | Commit message (Collapse) | Author |
|---|
|
Fixes this build warning:
drivers/net/wireless/iwlwifi/iwl-3945.c:411:13: warning: 'iwl3945_good_plcp_health' defined but not used
As per Johannes Berg.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599
Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.
For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.
Bug reporter confirmed that removing plcp check fixed problem for him.
Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
With commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 only one RF_KILL
interrupt will be seen by the driver when the interface is down.
Re-enable the interrupt when it occurs to see all transitions.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch reverts the following commit
ath9k: remove bfs_paprd_timestamp from struct ath_buf_state
Under high interference/noisy environment conditions where PAPRD frames
fails heavily introduces a possibility of double freeing skb's and causes
kernel panic after some time.This patch reverts back to the original approach
of using paprd_timestamp before freeing the PAPRD frame skb's
[ 194.193705] Pid: 0, comm: swapper Tainted: G D WC
2.6.35-22-generic #33-Ubuntu
[ 194.193712] Call Trace:
[ 194.193722] [<c05c6468>] ? printk+0x2d/0x35
[ 194.193732] [<c05c63c3>] panic+0x5a/0xd2
[ 194.193741] [<c05ca3ed>] oops_end+0xcd/0xd0
[ 194.193750] [<c0105f74>] die+0x54/0x80
[ 194.193758] [<c05c9a16>] do_trap+0x96/0xc0
[ 194.193837] [<c0103fb0>] ? do_invalid_op+0x0/0xa0
[ 194.193846] [<c010403b>] do_invalid_op+0x8b/0xa0
[ 194.193856] [<c020bd4c>] ? kfree+0xec/0xf0
[ 194.193866] [<c012ce18>] ? default_spin_lock_flags+0x8/0x10
[ 194.193877] [<c01de47a>] ? free_one_page+0x12a/0x2d0
[ 194.193888] [<c01e04dc>] ? __free_pages+0x1c/0x40
[ 194.193897] [<c05c97a7>] error_code+0x73/0x78
[ 194.193906] [<c020bd4c>] ? kfree+0xec/0xf0
[ 194.193915] [<c04ecdd0>] ? skb_release_data+0x70/0xa0
[ 194.193924] [<c04ecdd0>] skb_release_data+0x70/0xa0
[ 194.193933] [<c04ec997>] __kfree_skb+0x17/0x90
[ 194.193941] [<c04eca31>] consume_skb+0x21/0x40
[ 194.193964] [<f85e0b70>] ieee80211_tx_status+0x760/0x860 [mac80211]
[ 194.193979] [<f85caddf>] ath_tx_complete_buf+0x1bf/0x2c0 [ath9k]
[ 194.193988] [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[ 194.193997] [<c04ec40e>] ? skb_queue_tail+0x3e/0x50
[ 194.194010] [<f85cc803>] ath_tx_complete_aggr+0x823/0x940 [ath9k]
[ 194.194021] [<c0108a28>] ? sched_clock+0x8/0x10
[ 194.194030] [<c016bf14>] ? sched_clock_local+0xa4/0x180
[ 194.194040] [<c0139f57>] ? enqueue_sleeper+0x1e7/0x2b0
[ 194.194051] [<c013a194>] ? enqueue_entity+0x174/0x200
[ 194.194064] [<f85ce83d>] ath_tx_edma_tasklet+0x2bd/0x3b0 [ath9k]
[ 194.194074] [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[ 194.194088] [<f85c7b9f>] ath9k_tasklet+0x9f/0x190 [ath9k]
[ 194.194097] [<c01505d7>] tasklet_action+0xa7/0xb0
[ 194.194107] [<c015127c>] __do_softirq+0x9c/0x1b0
[ 194.194117] [<c01a7f64>] ? irq_to_desc+0x14/0x20
[ 194.194126] [<c0124fc4>] ? ack_apic_level+0x64/0x1f0
[ 194.194136] [<c01513d5>] do_softirq+0x45/0x50
[ 194.194145] [<c0151545>] irq_exit+0x65/0x70
[ 194.194153] [<c05cf665>] do_IRQ+0x55/0xc0
[ 194.194162] [<c016a6c7>] ? hrtimer_start+0x27/0x30
[ 194.194171] [<c0103630>] common_interrupt+0x30/0x38
[ 194.194181] [<c012c21a>] ? native_safe_halt+0xa/0x10
[ 194.194268] [<c010a2f9>] default_idle+0x49/0xb0
[ 194.194277] [<c0101fcc>] cpu_idle+0x8c/0xd0
[ 194.194286] [<c05b2431>] rest_init+0x71/0x80
[ 194.194295] [<c081981a>] start_kernel+0x36e/0x374
[ 194.194305] [<c08199dd>] ? pass_all_bootoptions+0x0/0xa
[ 194.194314] [<c08190d7>] i386_start_kernel+0xd7/0xdf
[ 194.194364] panic occurred, switching back to text console
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a off-by-one bug which bugged
the driver's PS-POLL capability.
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
wl1251_op_bss_info_changed()
In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.
This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates. Make it always return cpu-endian values.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue. As a result, we may not actually stop some queues during
reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
This patch adds the device id for the windy31 USB device to the rt73usb
driver.
Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.
Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In drivers/net/wireless/rtlwifi/pci.c::_rtl_pci_rx_interrupt() we call
dev_alloc_skb(), which may fail and return NULL, but we do not check the
returned value against NULL before dereferencing the returned pointer.
This may lead to a NULL pointer dereference which means we'll crash - not
good.
In a separate call to dev_alloc_skb(), the debug level is changed so that
the failure message will always be logged.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There are several places where ath_reset() was called without proper
calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls
directly to ath_reset and drop them from callers where it makes sense.
Also add them to the config callback around ath_update_txpow to fix a
crash that happens when the tx power changed before any vif is brought up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.
Cc: stable@kernel.org
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
For all the new devices, the sku information should read from EEPROM
but for legacy devices such as 4965, appearly the EEPROM does not
contain the necessary information. so skip the read from EEPROM
and go back to use software configuration.
Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
|
|
When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
ath5k_reset must be called with sc->lock. Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.
Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
GRETH: resolve SMP issues and other problems
GRETH: handle frame error interrupts
GRETH: avoid writing bad speed/duplex when setting transfer mode
GRETH: fixed skb buffer memory leak on frame errors
GRETH: GBit transmit descriptor handling optimization
GRETH: fix opening/closing
GRETH: added raw AMBA vendor/device number to match against.
cassini: Fix build bustage on x86.
e1000e: consistent use of Rx/Tx vs. RX/TX/rx/tx in comments/logs
e1000e: update Copyright for 2011
e1000: Avoid unhandled IRQ
r8169: keep firmware in memory.
netdev: tilepro: Use is_unicast_ether_addr helper
etherdevice.h: Add is_unicast_ether_addr function
ks8695net: Use default implementation of ethtool_ops::get_link
ks8695net: Disable non-working ethtool operations
USB CDC NCM: Don't deref NULL in cdc_ncm_rx_fixup() and don't use uninitialized variable.
vxge: Remember to release firmware after upgrading firmware
netdev: bfin_mac: Remove is_multicast_ether_addr use in netdev_for_each_mc_addr
ipsec: update MAX_AH_AUTH_LEN to support sha512
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI/PM: Report wakeup events before resuming devices
PCI/PM: Use pm_wakeup_event() directly for reporting wakeup events
PCI: sysfs: Update ROM to include default owner write access
x86/PCI: make Broadcom CNB20LE driver EMBEDDED and EXPERIMENTAL
x86/PCI: don't use native Broadcom CNB20LE driver when ACPI is available
PCI/ACPI: Request _OSC control once for each root bridge (v3)
PCI: enable pci=bfsort by default on future Dell systems
PCI/PCIe: Clear Root PME Status bits early during system resume
PCI: pci-stub: ignore zero-length id parameters
x86/PCI: irq and pci_ids patch for Intel Patsburg
PCI: Skip id checking if no id is passed
PCI: fix __pci_device_probe kernel-doc warning
PCI: make pci_restore_state return void
PCI: Disable ASPM if BIOS asks us to
PCI: Add mask bit definition for MSI-X table
PCI: MSI: Move MSI-X entry definition to pci_regs.h
Fix up trivial conflicts in drivers/net/{skge.c,sky2.c} that had in the
meantime been converted to not use legacy PCI power management, and thus
no longer use pci_restore_state() at all (and that caused trivial
conflicts with the "make pci_restore_state return void" patch)
|
|
We need to release_firmware() in order not to leak memory.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In the case of alloc_netdev_mq failure and kmalloc failure,
current implementation returns ERR_PTR(0).
As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR
macro. Fix it by setting proper error code for ret variable in the failure
cases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
Documentation/trace/events.txt: Remove obsolete sched_signal_send.
writeback: fix global_dirty_limits comment runtime -> real-time
ppc: fix comment typo singal -> signal
drivers: fix comment typo diable -> disable.
m68k: fix comment typo diable -> disable.
wireless: comment typo fix diable -> disable.
media: comment typo fix diable -> disable.
remove doc for obsolete dynamic-printk kernel-parameter
remove extraneous 'is' from Documentation/iostats.txt
Fix spelling milisec -> ms in snd_ps3 module parameter description
Fix spelling mistakes in comments
Revert conflicting V4L changes
i7core_edac: fix typos in comments
mm/rmap.c: fix comment
sound, ca0106: Fix assignment to 'channel'.
hrtimer: fix a typo in comment
init/Kconfig: fix typo
anon_inodes: fix wrong function name in comment
fix comment typos concerning "consistent"
poll: fix a typo in comment
...
Fix up trivial conflicts in:
- drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
- fs/ext4/ext4.h
Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
|
|
pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.
It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.
Patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=643758
Reported-and-tested-by: rbugz@biobind.com
Cc: stable@kernel.org # 2.6.34+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is an attempt to fix a long standing open bug:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334
The interrupt handler checks for INTA being -1, apparently that means that the
hardware is gone. But the interrupt handler defers actual interrupt processing
to a tasklet. By the time the tasklet is run and checks INTA again, the
hardware might be gone and INTA be -1, which confuses the driver because all
event bits are set.
The patch applies to 2.6.37.
Signed-off-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.
Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
USB devices do not require the chip test routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
net/bluetooth/Makefile
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
