| Age | Commit message (Collapse) | Author |
|---|
|
Currently only used when packet split mode is enabled with jumbo frames,
IP payload checksum (for fragmented UDP packets) is mutually exclusive with
receive hashing offload since the hardware uses the same space in the
receive descriptor for the hardware-provided packet checksum and the RSS
hash, respectively. Users currently must disable jumbos when receive
hashing offload is enabled, or vice versa, because of this incompatibility.
Since testing has shown that IP payload checksum does not provide any real
benefit, just remove it so that there is no longer a choice between jumbos
or receive hashing offload but not both as done in other Intel GbE drivers
(e.g. e1000, igb).
Also, add a missing check for IP checksum error reported by the hardware;
let the stack verify the checksum when this happens.
CC: stable <stable@vger.kernel.org> [3.4]
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using ethtool -C ethX rx-usecs 0 crashes with a divide by zero.
Refactor this function to fix this issue and make it more clear
what the intent of each conditional is. Add comment regarding
using a setting of zero.
CC: stable <stable@vger.kernel.org> [3.3+]
CC: David Ahern <daahern@cisco.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes a number of warnings such as:
CC drivers/net/ethernet/ti/davinci_cpdma.o
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: data definition
has no type or storage class
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: type defaults to
‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
drivers/net/ethernet/ti/davinci_cpdma.c:279:1: warning: parameter names
(without types) in function declaration
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Christian Riesch <christian.riesch@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John Linville says:
====================
Amitkumar Karwar gives us two mwifiex fixes: one fixes some skb
manipulations when handling some event messages; and another that
does some similar fixing on an error path.
Avinash Patil gives us a fix for for a memory leak in mwifiex.
Dan Rosenberg offers an NFC NCI fix to enforce some message length
limits to prevent buffer overflows.
Eliad Peller provides a mac80211 fix to prevent some frames from
being built with an invalid BSSID.
Eric Dumazet sends an NFC fix to prevent a BUG caused by a NULL
pointer dereference.
Felix Fietkau has an ath9k fix for a regression causing
LEAP-authenticated connection failures.
Johannes Berg provides an iwlwifi fix that eliminates some log SPAM
after an authentication/association timeout. He also provides a
mac80211 fix to prevent incorrectly addressing certain action frames
(and in so doing, to comply with the 802.11 specs).
Larry Finger provides a few USB IDs for the rtl8192cu driver --
should be harmless.
Panayiotis Karabassis provices a one-liner to fix kernel bug 42903
(a system freeze).
Randy Dunlap provides a one-line Kconfig change to prevent build
failures with some configurations.
Stone Piao provides an mwifiex sequence numbering fix and a fix
to prevent mwifiex from attempting to include eapol frames in an
aggregation frame.
Finally, Tom Hughes provides an ath9k fix for a NULL pointer
dereference.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The correct behavior is to program the interrupt coalescing regs
(RXICr/TXICr) in accordance with the Rx/Tx Q's "rx/txcoalescing"
flag. That is, if the coalescing flag is 0 for a given Rx/Tx queue
then the corresponding coalescing register should be cleared.
This behavior is correctly implemented for the single-queue mode
(SQ_SG_MODE), but not for the multi-queue mode (MQ_MG_MODE).
This fixes the later case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
usbnet_disconnect() will set intfdata to NULL before calling
the minidriver unbind function. The cdc_wdm subdriver cannot
know that it is disconnecting until the qmi_wwan unbind
function has called its disconnect function. This means that
we must be able to support the cdc_wdm subdriver operating
normally while usbnet_disconnect() is running, and in
particular that intfdata may be NULL.
The only place this matters is in qmi_wwan_cdc_wdm_manage_power
which is called from cdc_wdm. Simply testing for NULL
intfdata there is sufficient to allow it to continue working
at all times.
Fixes this Oops where a cdc-wdm device was closed while the
USB device was disconnecting, causing wdm_release to call
qmi_wwan_cdc_wdm_manage_power after intfdata was set to
NULL by usbnet_disconnect:
[41819.087460] BUG: unable to handle kernel NULL pointer dereference at 00000080
[41819.087815] IP: [<f8640458>] qmi_wwan_manage_power+0x68/0x90 [qmi_wwan]
[41819.088028] *pdpt = 000000000314f001 *pde = 0000000000000000
[41819.088028] Oops: 0002 [#1] SMP
[41819.088028] Modules linked in: qmi_wwan option usb_wwan usbserial usbnet
cdc_wdm nls_iso8859_1 nls_cp437 vfat fat usb_storage bnep rfcomm bluetooth
parport_pc ppdev binfmt_misc iptable_nat nf_nat nf_conntrack_ipv4
nf_conntrack nf_defrag_ipv4 iptable_mangle iptable_filter ip_tables
x_tables dm_crypt uvcvideo snd_hda_codec_realtek snd_hda_intel
videobuf2_core snd_hda_codec joydev videodev videobuf2_vmalloc
hid_multitouch snd_hwdep arc4 videobuf2_memops snd_pcm snd_seq_midi
snd_rawmidi snd_seq_midi_event ath9k mac80211 snd_seq ath9k_common ath9k_hw
ath snd_timer snd_seq_device sparse_keymap dm_multipath scsi_dh coretemp
mac_hid snd soundcore cfg80211 snd_page_alloc psmouse serio_raw microcode
lp parport dm_mirror dm_region_hash dm_log usbhid hid i915 drm_kms_helper
drm r8169 i2c_algo_bit wmi video [last unloaded: qmi_wwan]
[41819.088028]
[41819.088028] Pid: 23292, comm: qmicli Not tainted 3.4.0-5-generic #11-Ubuntu GIGABYTE T1005/T1005
[41819.088028] EIP: 0060:[<f8640458>] EFLAGS: 00010246 CPU: 1
[41819.088028] EIP is at qmi_wwan_manage_power+0x68/0x90 [qmi_wwan]
[41819.088028] EAX: 00000000 EBX: 00000000 ECX: 000000c3 EDX: 00000000
[41819.088028] ESI: c3b27658 EDI: 00000000 EBP: c298bea4 ESP: c298be98
[41819.088028] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
[41819.088028] CR0: 8005003b CR2: 00000080 CR3: 3605e000 CR4: 000007f0
[41819.088028] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[41819.088028] DR6: ffff0ff0 DR7: 00000400
[41819.088028] Process qmicli (pid: 23292, ti=c298a000 task=f343b280 task.ti=c298a000)
[41819.088028] Stack:
[41819.088028] 00000000 c3b27658 e2a80d00 c298beb0 f864051a c3b27600 c298bec0 f9027099
[41819.088028] c2fd6000 00000008 c298bef0 c1147f96 00000001 00000000 00000000 f4e54790
[41819.088028] ecf43a00 ecf43a00 c2fd6008 c2fd6000 ebbd7600 ffffffb9 c298bf08 c1144474
[41819.088028] Call Trace:
[41819.088028] [<f864051a>] qmi_wwan_cdc_wdm_manage_power+0x1a/0x20 [qmi_wwan]
[41819.088028] [<f9027099>] wdm_release+0x69/0x70 [cdc_wdm]
[41819.088028] [<c1147f96>] fput+0xe6/0x210
[41819.088028] [<c1144474>] filp_close+0x54/0x80
[41819.088028] [<c1046a65>] put_files_struct+0x75/0xc0
[41819.088028] [<c1046b56>] exit_files+0x46/0x60
[41819.088028] [<c1046f81>] do_exit+0x141/0x780
[41819.088028] [<c107248f>] ? wake_up_state+0xf/0x20
[41819.088028] [<c1053f48>] ? signal_wake_up+0x28/0x40
[41819.088028] [<c1054f3b>] ? zap_other_threads+0x6b/0x80
[41819.088028] [<c1047864>] do_group_exit+0x34/0xa0
[41819.088028] [<c10478e8>] sys_exit_group+0x18/0x20
[41819.088028] [<c15bb7df>] sysenter_do_call+0x12/0x28
[41819.088028] Code: 04 83 e7 01 c1 e7 03 0f b6 42 18 83 e0 f7 09 f8 88 42
18 8b 43 04 e8 48 9a dd c8 89 f0 8b 5d f4 8b 75 f8 8b 7d fc 89 ec 5d c3 90
<f0> ff 88 80 00 00 00 0f 94 c0 84 c0 75 b7 31 f6 8b 5d f4 89 f0
[41819.088028] EIP: [<f8640458>] qmi_wwan_manage_power+0x68/0x90 [qmi_wwan] SS:ESP 0068:c298be98
[41819.088028] CR2: 0000000000000080
[41819.149492] ---[ end trace 0944479ff8257f55 ]---
Reported-by: Marius Bjørnstad Kotsbak <marius.kotsbak@gmail.com>
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking update from David Miller:
1) Pairing and deadlock fixes in bluetooth from Johan Hedberg.
2) Add device IDs for AR3011 and AR3012 bluetooth chips. From
Giancarlo Formicuccia and Marek Vasut.
3) Fix wireless regulatory deadlock, from Eliad Peller.
4) Fix full TX ring panic in bnx2x driver, from Eric Dumazet.
5) Revert the two commits that added skb_orphan_try(), it causes
erratic bonding behavior with UDP clients and the gains it used to
give are mostly no longer happening due to how BQL works. From Eric
Dumazet.
6) It took two tries, but Thomas Graf fixed a problem wherein we
registered ipv6 routing procfs files before their backend data were
initialized properly.
7) Fix max GSO size setting in be2net, from Sarveshwar Bandi.
8) PHY device id mask is wrong for KSZ9021 and KS8001 chips, fix from
Jason Wang.
9) Fix use of stale SKB data pointer after skb_linearize() call in
batman-adv, from Antonio Quartulli.
10) Fix memory leak in IXGBE due to missing __GFP_COMP, from Alexander
Duyck.
11) Fix probing of Gobi devices in qmi_wwan usbnet driver, from Bjørn
Mork.
12) Fix suspend/resume and open failure handling in usbnet from Ming
Lei.
13) Attempt to fix device r8169 hangs for certain chips, from Francois
Romieu.
14) Fix advancement of RX dirty pointer in some situations in sh_eth
driver, from Yoshihiro Shimoda.
15) Attempt to fix restart of IPV6 routing table dumps when there is an
intervening table update. From Eric Dumazet.
16) Respect security_inet_conn_request() return value in ipv6 TCP. From
Neal Cardwell.
17) Add another iPAD device ID to ipheth driver, from Davide Gerhard.
18) Fix access to freed SKB in l2tp_eth_dev_xmit(), and fix l2tp lockdep
splats, from Eric Dumazet.
19) Make sure all bridge devices, regardless of whether they were
created via netlink or ioctls, have their rtnetlink ops hooked up.
From Thomas Graf and Stephen Hemminger.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
9p: fix min_t() casting in p9pdu_vwritef()
can: flexcan: use be32_to_cpup to handle the value of dt entry
xen/netfront: teardown the device before unregistering it.
bridge: Assign rtnl_link_ops to bridge devices created via ioctl (v2)
vhost: use USER_DS in vhost_worker thread
ixgbe: Do not pad FCoE frames as this can cause issues with FCoE DDP
net: l2tp_eth: use LLTX to avoid LOCKDEP splats
mac802154: add missed braces
net: l2tp_eth: fix l2tp_eth_dev_xmit race
net/mlx4_en: Release QP range in free_resources
net/mlx4: Use single completion vector after NOP failure
net/mlx4_en: Set correct port parameters during device initialization
ipheth: add support for iPad
caif-hsi: Add missing return in error path
caif-hsi: Bugfix - Piggyback'ed embedded CAIF frame lost
caif: Clear shutdown mask to zero at reconnect.
tcp: heed result of security_inet_conn_request() in tcp_v6_conn_request()
ipv6: fib: fix fib dump restart
batman-adv: fix race condition in TT full-table replacement
batman-adv: only drop packets of known wifi clients
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Free ap_custom_ie before return from function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Commit 3a2923e83c introduced a bug when a corrupt descriptor
is encountered - although the following descriptor is discarded
and returned to the queue for reuse the associated frame is
also returned for processing. This leads to a panic:
BUG: unable to handle kernel NULL pointer dereference at 000000000000003a
IP: [<ffffffffa02599a5>] ath_rx_tasklet+0x165/0x1b00 [ath9k]
Call Trace:
<IRQ>
[<ffffffff812d7fa0>] ? map_single+0x60/0x60
[<ffffffffa028f044>] ? ath9k_ioread32+0x34/0x90 [ath9k]
[<ffffffffa0292eec>] athk9k_tasklet+0xdc/0x160 [ath9k]
[<ffffffff8105e133>] tasklet_action+0x63/0xd0
[<ffffffff8105dbc0>] __do_softirq+0xc0/0x1e0
[<ffffffff8101a873>] ? native_sched_clock+0x13/0x80
[<ffffffff815f9d5c>] call_softirq+0x1c/0x30
[<ffffffff810151f5>] do_softirq+0x75/0xb0
[<ffffffff8105df95>] irq_exit+0xb5/0xc0
[<ffffffff815fa5b3>] do_IRQ+0x63/0xe0
[<ffffffff815f0cea>] common_interrupt+0x6a/0x6a
<EOI>
[<ffffffff8131840a>] ? intel_idle+0xea/0x150
[<ffffffff813183eb>] ? intel_idle+0xcb/0x150
[<ffffffff814a1db9>] cpuidle_enter+0x19/0x20
[<ffffffff814a23d9>] cpuidle_idle_call+0xa9/0x240
[<ffffffff8101c4bf>] cpu_idle+0xaf/0x120
[<ffffffff815cda8e>] rest_init+0x72/0x74
[<ffffffff81cf4c1a>] start_kernel+0x3b7/0x3c4
[<ffffffff81cf4662>] ? repair_env_string+0x5e/0x5e
[<ffffffff81cf4346>] x86_64_start_reservations+0x131/0x135
[<ffffffff81cf444a>] x86_64_start_kernel+0x100/0x10f
Making sure bf is cleared to NULL in this case restores the
old behaviour.
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
https://bugzilla.kernel.org/show_bug.cgi?id=42903
Based on the work of <fynivx@gmail.com>
Signed-off-by: Panayiotis Karabassis <panayk@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The latest Realtek driver for the RTL8188CU and RTL8192CU chips adds three
new USB IDs.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.
Cc: stable <stable@vger.kernel.org> # v3.2+
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fixes:
[ 15.470311] WARNING: at /local/scratch/ianc/devel/kernels/linux/fs/sysfs/file.c:498 sysfs_attr_ns+0x95/0xa0()
[ 15.470326] sysfs: kobject eth0 without dirent
[ 15.470333] Modules linked in:
[ 15.470342] Pid: 12, comm: xenwatch Not tainted 3.4.0-x86_32p-xenU #93
and
[ 9.150554] BUG: unable to handle kernel paging request at 2b359000
[ 9.150577] IP: [<c1279561>] linkwatch_do_dev+0x81/0xc0
[ 9.150592] *pdpt = 000000002c3c9027 *pde = 0000000000000000
[ 9.150604] Oops: 0002 [#1] SMP
[ 9.150613] Modules linked in:
This is http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=675190
Reported-by: George Shuklin <george.shuklin@gmail.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: William Dauchy <wdauchy@gmail.com>
Cc: stable@kernel.org
Cc: 675190@bugs.debian.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.
To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.
CC: <stable@vger.kernel.org>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a missing resource release in ring cleanup.
Not doing this leaves a range of QPs that are being reserved,
and no one can use them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a crash at the error flow of NOP command which caused the driver to try and use
a completion vector which wasn't allocated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set valid port parameters: MTU and flow control configuration when
configuring the port during HW device initialization,
prior to the net device open() being called.
Using invalid parameters (such as all zeros)
could lead to bad firmware behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the iPad to the ipheth driver.
(product id = 0x129a)
Signed-off-by: Davide Gerhard <rainbow@irh.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a missing return, causing access to freed memory.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a piggyback'ed descriptor containing an
embedded frame, but no payload, the embedded frame was
lost.
Signed-off-by: Per Ellefsen <per.ellefsen@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When authentication/association timed out, the driver would
complain bitterly, printing the message
ACTIVATE a non DRIVER active station id ... addr ...
The cause turns out to be that when the AP station is added
but we don't associate, the IWL_STA_UCODE_INPROGRESS is set
but never cleared. This then causes iwl_restore_stations()
to attempt to resend it because it uses the flag internally
and uploads even if it didn't set it itself.
To fix this issue and not upload the station again when it
has already been removed by mac80211, clear the flag after
adding it in case we add it only for association.
Cc: stable@vger.kernel.org
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mainline build reports:
warning: (WL12XX) selects WLCORE which has unmet direct dependencies (NETDEVICES && WLAN && WL_TI && GENERIC_HARDIRQS && MAC80211 && INET)
The INET dependency was added in commit
3c6af5b54fe74b6e56efadc22927e4055d00e9fc:
wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_
notifier'
wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_no
tifier'
Driver is doing some filtering based on IP addresses...
but this driver no longer has that code and it builds fine even when
CONFIG_INET is not enabled, so drop that dependency and eliminate the
kconfig warning message.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
commit 7a532fe7131216a02c81a6c1b1f8632da1195a58
ath9k_hw: fix interpretation of the rx KeyMiss flag
This commit used the rx key miss indication to detect packets that were
passed from the hardware without being decrypted, however it seems that
this bit is not only undefined in the static WEP case, but also for
dynamically allocated WEP keys. This caused a regression when using
WEP-LEAP.
This patch fixes the regression by keeping track of which key indexes
refer to CCMP keys and only using the key miss indication for those.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Coult -> Could
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following commit couldn't work if the RMCR is not set to 1.
"net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens"
commit id 79fba9f51755c704c0a7d7b7f0df10874dc0a744
If RMCR is not set, the controller will clear the EDRRR after it received
a frame. In this case, the driver doesn't need to fix the value of
cur_rx/dirty_rx. The driver only needs it when the controll detects
receive descriptors are empty.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 8168evl (RTL_GIGA_MAC_VER_34) based Gigabyte GA-990FXA motherboards
are very prone to NETDEV watchdog problems without this change. See
https://bugzilla.kernel.org/show_bug.cgi?id=42899 for instance.
I don't know why it *works*. It's depressingly effective though.
For the record:
- the problem may go along IOMMU (AMD-Vi) errors but it really looks
like a red herring.
- the patch sets the RX_MULTI_EN bit. If the 8168c doc is any guide,
the chipset now fetches several Rx descriptors at a time.
- long ago the driver ignored the RX_MULTI_EN bit.
e542a2269f232d61270ceddd42b73a4348dee2bb changed the RxConfig
settings. Whatever the problem it's now labeled a regression.
- Realtek's own driver can identify two different 8168evl devices
(CFG_METHOD_16 and CFG_METHOD_17) where the r8169 driver only
sees one. It sucks.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If usbnet is resumed by remote wakeup, generally there are
some packets comming to be handled, so allocate and submit
rx URBs in usbnet_resume to avoid delays introduced by tasklet.
Otherwise, usbnet may have been runtime suspended before the
usbnet_bh is executed to schedule Rx URBs.
Without the patch, usbnet can't recieve any packets from peer
in runtime suspend state if runtime PM is enabled and
autosuspend_delay is set as zero.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch decreases dev->suspend_count in the -EBUSY failure path
of usbnet_suspend. Without the change, the later runtime suspend
will do nothing except for increasing dev->suspend_count.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without clearing OPEN flag in failure path, runtime or system resume
may submit interrupt/rx URB and start tx queue mistakenly on a
interface in DOWN state.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ignoring interfaces with additional descriptors is not a reliable
method for locating the correct interface on Gobi devices. There
is at least one device where this method fails:
https://bbs.archlinux.org/viewtopic.php?id=143506
The result is that the AT command port (interface #2) is hidden
from qcserial, preventing traditional serial modem usage:
[ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device
[ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22
[ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device
[ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22
[ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected
[ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0
[ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected
[ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1
Use static interface numbers taken from the interface map in
qcserial for all Gobi devices instead:
Gobi 1K USB layout:
0: serial port (doesn't respond)
1: serial port (doesn't respond)
2: AT-capable modem port
3: QMI/net
Gobi 2K+ USB layout:
0: QMI/net
1: DM/DIAG (use libqcdm from ModemManager for communication)
2: AT-capable modem port
3: NMEA
This should be more reliable over all, and will also prevent the
noisy "probe failed" messages. The whitelisting logic is expected
to be replaced by direct interface number matching in 3.6.
Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de>
Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic
Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
skb allocated during initialisation is reused for receiving
commands/events by USB interface. We miss to reset skb->data in
failure cases. This patch takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch ensures uniformity in event skb sent by interface code
(USB/PCIe/SDIO) which automatically fixes following bugs.
1) For USB interface, same buffer is reused for receiving cmd and
events from firmware. While handling events, we perform
skb_pull(skb, 4) to remove event header. Corresponding skb_push()
call is missing while submitting the buffer.
2) For PCIe interface, event skb is passed with event header.
Recently added uAP events EVENT_UAP_STA_ASSOC, EVENT_UAP_STA_DEAUTH
will not work for PCIe, as they assume event skb points to event body.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After association, STA will go through eapol handshake with WPS
enabled AP. It's observed that WPS handshake fails with some 11n
AP. The reason for the failure is that the eapol packet is sent
via 11n frame aggregation.
The eapol packet should be sent directly without 11n aggregation.
This patch fixes the problem by adding WPS session control while
dequeuing Tx packets for transmission.
Cc: "3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.
Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.
Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Cc: "3.0.y, 3.1.y, 3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.
Cc: stable@vger.kernel.org [3.4+]
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When debugging is disabled, the event log functions aren't
functional in the way that the debugfs file expects. This
leads to the debugfs access crashing. Since the event log
functions aren't functional then, remove the debugfs file
when CONFIG_IWLWIFI_DEBUG is not set.
Cc: stable@kernel.org
Reported-by: Lekensteyn <lekensteyn@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c790e051ff677e023435d770d2ffa174 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes two memory leaks in the SPI initialization code.
Patch based on old maemo patch by:
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Always report beacon loss to the stack, not only when in powersave
state. This is because there's possibility that the driver disables
PSM before it handles old BSS_LOSE_EVENT, so beacon loss has to be
reported.
Patch based on old maemo patch by:
Janne Ylalehto <janne.ylalehto@nokia.com>
Juuso Oikarinen <juuso.oikarinen@nokia.com>
Luciano Coelho <luciano.coelho@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cast MSB part of current TSF to u64 to prevent loss of most
significant bits. MSB should also be shifted by 32.
Patch based on old maemo patch by:
Yuri Kululin <ext-yuri.kululin@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a memory leak that was introduced in the 3.4 kernel. The
leak occurred when FCoE was enabled and traffic was passed over the FCoE
rings reserved for FCoE. The memory leak was due to us not populating the
compound page information on the order 1 pages needed for FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix Kconfig file to make sure that PTP and IGB/IXGBE are both either
in-kernel or modules, not mixed. Having the build status mixed causes
compile errors.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
i210/i211 device has only 16 RAR address filters like 82575, instead of
32 like i350. This patch removes the entries for i210/i211 in the
get_invariants function which was setting them for 32. This ensures that
they will get the default value which is the correct one.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
add_virtual_intf() needs to return an ERR_PTR(), instead of NULL,
on errors, otherwise cfg80211 will crash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
"qual" used to be declared on the stack, but then in 998a5a7d6a ("airo:
reduce stack memory footprint") we made it dynamically allocated.
Unfortunately the memcpy() here was missed and it's still copying stack
memory instead of the data that we want. In other words, "&qual" should
be "qual".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When running heavy traffic we stop the tx queue if the pending
packet count reaches certain threshold. Later, the tx queue should
be woken up as soon as the packet count falls below the threshold.
Current code wakes TX queue up on STA interface only. Removing the
check for STA interface will allow both STA and AP interfaces to
resume transmit when tx_pending count becomes low.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
spin_unlock_bh(&txq->lock) already disables softirqs so we don't want
to do it here. Fixes smatch warnings:
drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:'
drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:'
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.
This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
