| Age | Commit message (Collapse) | Author |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
wimax/i2400m: fix missing endian correction read in fw loader
net8139: fix a race at the end of NAPI
pktgen: Fix accuracy of inter-packet delay.
pkt_sched: gen_estimator: add a new lock
net: deliver skbs on inactive slaves to exact matches
ipv6: fix ICMP6_MIB_OUTERRORS
r8169: fix mdio_read and update mdio_write according to hw specs
gianfar: Revive the driver for eTSEC devices (disable timestamping)
caif: fix a couple range checks
phylib: Add support for the LXT973 phy.
net: Print num_rx_queues imbalance warning only when there are allocated queues
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/inaky/wimax
|
|
i2400m_fw_hdr_check() was accessing hardware field
bcf_hdr->module_type (little endian 32) without converting to host
byte sex.
Reported-by: Данилин Михаил <mdanilin@nsg.net.ru>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid validate_cis failure on CIS override
pcmcia: dev_node removal bugfix
pcmcia: yenta_socket.c Remove extra #ifdef CONFIG_YENTA_TI
pcmcia: only keep saved I365_CSCINT flag if there is no PCI irq
|
|
fix a race at the end of NAPI complete processing, it had
better do __napi_complete() first before re-enable interrupt.
Signed-off-by:Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit cc772ab7cdcaa24d1fae332d92a1602788644f7a ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).
That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:
Timestamp incoming packets as padding bytes. PAL field is set
to 8 if the PAL field is programmed to less than 8. Must be set
to zero if TMR_CTRL[TE]=0.
I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.
Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.
For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements a work around for Erratum 5, "3.3 V Fiber Speed
Selection." If the hardware wiring does not respect this erratum, then
fiber optic mode will not work properly.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
mac80211: fix deauth before assoc
iwlwifi: add missing rcu_read_lock
mac80211: fix function pointer check
wireless: remove my name from the maintainer list
ath5k: fix NULL pointer in antenna configuration
p54usb: Add device ID for Dell WLA3310 USB
wl1251: fix a memory leak in probe
ipmr: dont corrupt lists
8139too: fix buffer overrun in rtl8139_init_board
asix: check packet size against mtu+ETH_HLEN instead of ETH_FRAME_LEN
r8169: fix random mdio_write failures
ip6mr: fix a typo in ip6mr_for_each_table()
iwlwifi: move sysfs_create_group to post request firmware
iwlwifi: add name to Maintainers list
iwl3945: fix internal scan
iwl3945: enable stuck queue detection on 3945
ipv6: avoid high order allocations
ath5k: retain promiscuous setting
ath5k: depend on CONFIG_PM_SLEEP for suspend/resume functions
mac80211: process station blockack action frames from work
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Using ieee80211_find_sta() needs to be under
RCU read lock, which iwlwifi currently misses,
so fix it.
Cc: stable@kernel.org
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the channel is not set yet and we configure the antennas just store the
setting. It will be activated during the next reset, when the channel is set.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add Dell WLA3310 USB wireless card, which has a Z-Com XG-705A chipset, to the
USB Ids in p54usb.
Signed-off-by: Jason Dravet <dravet@hotmail.com>
Tested-by: Richard Gregory Tillmore <rtillmore@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Cc: <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
wl1251_sdio_probe() error path is missing wl1251_free_hw, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Patch c7c2fa07 removed one line too much from smc91c92_cs.c.
Reported-by: Komuro <komurojun-mbn@nifty.com>
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Fix rtl_chip_info buffer overrun when we can't identify the chip.
(i = ARRAY_SIZE (rtl_chip_info) in this case)
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver checks received packet is too large in asix_rx_fixup() and fails if it is. Problem is
that MTU might be set larger than 1500 and asix fails to work correctly with VLAN tagged
packets. The check should be 'dev->net->mtu + ETH_HLEN' instead.
Tested with AX88772.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some configurations need delay between the "write completed" indication
and new write to work reliably.
Realtek driver seems to use longer delay when polling the "write complete"
bit, so it waits long enough between writes with high probability (but
could probably break too). This patch adds a new udelay to make sure we
wait unconditionally some time after the write complete indication.
This caused a regression with XID 18000000 boards when the board specific
phy configuration writing many mdio registers was added in commit
2e955856ff (r8169: phy init for the 8169scd). Some of the configration
mdio writes would almost always fail, and depending on failure might leave
the PHY in non-working state.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the sysfs_create_group to iwl_ucode_callback after we
have safely got the firmware.
The motivation to do this comes from a warning from lockdep which detected
that we request priv->mutex while holding s_active during a sysfs request
(show_statistics in the example copy pasted). The reverse order exists upon
request_firmware: request_firmware which is a sysfs operation
that requires s_active is run under priv->mutex.
This ensures that we don't get sysfs request before we finish to request
the firmware, avoiding this deadlock.
=======================================================
[ INFO: possible circular locking dependency detected ]
-------------------------------------------------------
cat/2595 is trying to acquire lock:
(&priv->mutex){+.+.+.}, at: [<facfa598>] show_statistics+0x48/0x100 [iwlagn]
but task is already holding lock:
(s_active){++++.+}, at: [<c0580ebd>] sysfs_get_active_two+0x1d/0x50
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (s_active){++++.+}:
[<c0489b74>] __lock_acquire+0xc44/0x1230
[<c048a1ed>] lock_acquire+0x8d/0x110
[<c0581499>] sysfs_addrm_finish+0xe9/0x180
[<c057f64a>] sysfs_hash_and_remove+0x4a/0x80
[<c05829d4>] sysfs_remove_group+0x44/0xd0
[<c0714b75>] dpm_sysfs_remove+0x15/0x20
[<c070dac8>] device_del+0x38/0x170
[<c070dc1e>] device_unregister+0x1e/0x60
[<c071838d>] _request_firmware+0x29d/0x550
[<c07186c7>] request_firmware+0x17/0x20
[<fad01bf1>] iwl_mac_start+0xb1/0x1230 [iwlagn]
[<fa46ba06>] ieee80211_open+0x436/0x6f0 [mac80211]
[<c0808cd2>] dev_open+0x92/0xf0
[<c0808b2b>] dev_change_flags+0x7b/0x190
[<c08148e8>] do_setlink+0x178/0x3b0
[<c0815169>] rtnl_setlink+0xf9/0x130
[<c081453b>] rtnetlink_rcv_msg+0x1bb/0x1f0
[<c0827ce6>] netlink_rcv_skb+0x86/0xa0
[<c081436c>] rtnetlink_rcv+0x1c/0x30
[<c08279c3>] netlink_unicast+0x263/0x290
[<c0828768>] netlink_sendmsg+0x1c8/0x2a0
[<c07f85fd>] sock_sendmsg+0xcd/0x100
[<c07f964d>] sys_sendmsg+0x15d/0x290
[<c07f9e6b>] sys_socketcall+0xeb/0x2a0
[<c040ad9f>] sysenter_do_call+0x12/0x38
-> #0 (&priv->mutex){+.+.+.}:
[<c0489f84>] __lock_acquire+0x1054/0x1230
[<c048a1ed>] lock_acquire+0x8d/0x110
[<c08bb358>] __mutex_lock_common+0x58/0x470
[<c08bb84a>] mutex_lock_nested+0x3a/0x50
[<facfa598>] show_statistics+0x48/0x100 [iwlagn]
[<c070d219>] dev_attr_show+0x29/0x50
[<c057fecd>] sysfs_read_file+0xdd/0x190
[<c052880f>] vfs_read+0x9f/0x190
[<c0528d22>] sys_read+0x42/0x70
[<c040ad9f>] sysenter_do_call+0x12/0x38
other info that might help us debug this:
3 locks held by cat/2595:
#0: (&buffer->mutex){+.+.+.}, at: [<c057fe25>] sysfs_read_file+0x35/0x190
#1: (s_active){++++.+}, at: [<c0580ecd>] sysfs_get_active_two+0x2d/0x50
#2: (s_active){++++.+}, at: [<c0580ebd>] sysfs_get_active_two+0x1d/0x50
stack backtrace:
Pid: 2595, comm: cat Not tainted 2.6.33-tp-rc4 #2
Call Trace:
[<c08b99ab>] ? printk+0x1d/0x22
[<c0487752>] print_circular_bug+0xc2/0xd0
[<c0489f84>] __lock_acquire+0x1054/0x1230
[<c0478d81>] ? sched_clock_cpu+0x121/0x180
[<c048a1ed>] lock_acquire+0x8d/0x110
[<facfa598>] ? show_statistics+0x48/0x100 [iwlagn]
[<c08bb358>] __mutex_lock_common+0x58/0x470
[<facfa598>] ? show_statistics+0x48/0x100 [iwlagn]
[<c08bb84a>] mutex_lock_nested+0x3a/0x50
[<facfa598>] ? show_statistics+0x48/0x100 [iwlagn]
[<facfa598>] show_statistics+0x48/0x100 [iwlagn]
[<c0580cf9>] ? sysfs_get_active+0x69/0xb0
[<facfa550>] ? show_statistics+0x0/0x100 [iwlagn]
[<c070d219>] dev_attr_show+0x29/0x50
[<c057fecd>] sysfs_read_file+0xdd/0x190
[<c05ff314>] ? security_file_permission+0x14/0x20
[<c0528242>] ? rw_verify_area+0x62/0xd0
[<c052880f>] vfs_read+0x9f/0x190
[<c047745b>] ? up_read+0x1b/0x30
[<c057fdf0>] ? sysfs_read_file+0x0/0x190
[<c04af3b4>] ? audit_syscall_entry+0x1f4/0x220
[<c0528d22>] sys_read+0x42/0x70
[<c040ad9f>] sysenter_do_call+0x12/0x38
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
|
Port of internal scan to iwl3945 missed introduction
of iwl3945_get_single_channel_for_scan.
Fix the following bug by introducing the iwl3945_get_single_channel_for_scan
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2208
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
|
We learn from
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1834 and
https://bugzilla.redhat.com/show_bug.cgi?id=589777
that 3945 can also suffer from a stuck command queue. Enable stuck queue
detection for iwl3945 to enable recovery in this case.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
X25: remove duplicated #include
tcp: use correct net ns in cookie_v4_check()
rps: tcp: fix rps_sock_flow_table table updates
ppp_generic: fix multilink fragment sizes
syncookies: remove Kconfig text line about disabled-by-default
ixgbe: only check pfc bits in hang logic if pfc is enabled
net: check for refcount if pop a stacked dst_entry
ixgbe: return IXGBE_ERR_RAR_INDEX when out of range
act_pedit: access skb->data safely
sfc: Store port number in net_device::dev_id
epic100: Test __BIG_ENDIAN instead of (non-existent) CONFIG_BIG_ENDIAN
tehuti: return -EFAULT on copy_to_user errors
isdn/kcapi: return -EFAULT on copy_from_user errors
e1000e: change logical negate to bitwise
sfc: Get port number from CS_PORT_NUM, not PCI function number
cls_u32: use skb_header_pointer() to dereference data safely
TCP: tcp_hybla: Fix integer overflow in slow start increment
act_nat: fix the wrong checksum when addr isn't in old_addr/mask
net/fec: fix pm to survive to suspend/resume
korina: count RX DMA OVR as rx_fifo_error
...
|
|
Remove duplicated #include('s) in drivers/net/wan/x25_asy.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix bug in multilink fragment size calculation introduced by
commit 9c705260feea6ae329bc6b6d5f6d2ef0227eda0a
"ppp: ppp_mp_explode() redesign"
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only check pfc bits in hang logic if PFC is enabled. Previously,
if DCB was enabled but PFC was disabled the incorrect pause
bits would be checked.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 56d1de0a21db28e41741cfa0a66e18bc8d920554, "ath5k: clean up
filter flags setting" introduced a regression in monitor mode such
that the promisc filter flag would get lost.
Although we set the promisc flag when it changed, we did not
preserve it across subsequent calls to configure_filter. This patch
restores the original functionality.
Cc: stable@kernel.org
Bisected-by: weedy2887@gmail.com
Tested-by: weedy2887@gmail.com
Tested-by: Rick Farina <sidhayn@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When building a kernel with CONFIG_PM=y but neither suspend nor
hibernate support, the compiler complains about the static functions
ath5k_pci_suspend() and ath5k_pci_resume() not being used:
drivers/net/wireless/ath/ath5k/base.c:713:12: warning: ‘ath5k_pci_suspend’ defined but not used
drivers/net/wireless/ath/ath5k/base.c:722:12: warning: ‘ath5k_pci_resume’ defined but not used
Depending on CONFIG_PM_SLEEP rather than CONFIG_PM fixes the issue.
Signed-off-by: Tobias Doerffel <tobias.doerffel@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This reverts commit 15920d8afc87861672e16fa95ae2764b065d6dd3.
This patch was discovered to cause some hostap devices to fail to
initialized.
https://bugzilla.kernel.org/show_bug.cgi?id=16111
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/macio: Fix probing of macio devices by using the right of match table
agp/uninorth: Fix oops caused by flushing too much
powerpc/pasemi: Update MAINTAINERS file
powerpc/cell: Fix integer constant warning
powerpc/kprobes: Remove resume_execution() in kprobes
powerpc/macio: Don't dereference pointer before null check
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
|
|
Based on original patch from Shirley Ma <xma@us.ibm.com>
Return IXGBE_ERR_RAR_INDEX when RAR index is out of range, instead of
returning IXGBE_SUCCESS.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This exposes the port number to userland through sysfs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Probably no one has used this driver on big-endian systems, since it was
setting up descriptor swapping if CONFIG_BIG_ENDIAN is set, which it
never is, since that symbol is not mentioned anywhere else in the kernel
source. Switch this test to a check for __BIG_ENDIAN so it has a chance
at working.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
copy_to_user() returns the number of bytes remaining but we want to
return a negative error code here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bitwise negate is intended here. With the logical negate the
condition is always false.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A single shared memory region used to communicate with firmware is
mapped into both PCI PFs of the SFC9020 and SFL9021. Drivers must be
able to identify which port they are addressing in order to use the
correct sub-region. Currently we use the PCI function number, but the
PCI address may be virtualised. Use the CS_PORT_NUM register field
defined for just this purpose.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* in the actual driver, calling fec_stop and fec_enet_init doesn't
allow to have a working network interface at resume (where a
ifconfig down and up is required to recover the interface)
* by using fec_enet_close and fec_enet_open, this patch solves this
problem and handle the case where the link changed between suspend
and resume
* this patch also disable clock at suspend and reenable it at resume
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This way, RX DMA overruns (actually being caused by overrun of the
512byte input FIFO) show up in ifconfig output. The rx_fifo_errors
counter is unused otherwise.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch completes commit 89d71a66c40d629e3b1285def543ab1425558cd5
which missed this spot, as it seems.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By calling korina_restart(), the IRQ handler tries to disable the
interrupt it's currently serving. This leads to a deadlock since
disable_irq() waits for any running IRQ handlers to finish before
returning. This patch addresses the issue by turning korina_restart()
into a workqueue task, which is then scheduled when needed.
Reproducing the deadlock is easily done using e.g. GNU netcat to send
large amounts of UDP data to the host running this driver.
Note that the same problem (and fix) applies to TX FIFO underruns, but
apparently these are less easy to trigger.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To make get/set netlink VF_PORT truly symmetrical, we need to keep track
of what items are set and only return those items on get. Previously, the
driver wasn't differentiating between a set of attr with a NULL string,
for example, and not setting the attr at all. We only want to return
the NULL string if the attr was actually set with a NULL string. Otherwise,
don't return the attr.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The regression is caused by:
commit 4327ba435a56ada13eedf3eb332e583c7a0586a9
bnx2: Fix netpoll crash.
If ->open() and ->close() are called multiple times, the same napi structs
will be added to dev->napi_list multiple times, corrupting the dev->napi_list.
This causes free_netdev() to hang during rmmod.
We fix this by calling netif_napi_del() during ->close().
Also, bnx2_init_napi() must not be in the __devinit section since it is
called by ->open().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Grant patches added an of mach table to struct device_driver. However,
while he changed the macio device code to use that, he left the match
table pointer in struct macio_driver and didn't update drivers to use
the "new" one, thus breaking the probing.
This completes the change by moving all drivers to setup the "new"
one, removing all traces of the old one, and while at it (since it
changes the exact same locations), I also remove two other duplicates
from struct driver which are the name and owner fields.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
We can wake all queues after a chip reset since everything should be set up and
we are ready to transmit. If we don't do that we might end up starting up with
stopped queues, not beeing able to transmit. (This started to happen after
"ath5k: clean up queue manipulation" but since periodic calibration also
stopped and started the queues this effect was hidden most of the time).
This way we can also get rid of the superfluous ath5k_reset_wake() function.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Add missing validate_addr hook
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert TX hook to netdev_tx_t type
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
virtio-net bounces buffer allocations off to
a thread if it can't allocate buffers from the atomic
pool. However, if posting buffers still requires atomic
buffers, this is unlikely to succeed.
Fix by passing in the proper gfp_t parameter.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code fails on ppc as hdr.timeout is not being converted
to le32.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes build error caused by the OF device_node pointer
being moved into struct device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
