Age | Commit message (Collapse) | Author |
|
|
|
The patch "net: gianfar: do not try to cleanup TX packets if they are
not done" for 3.12-rt left out the return value for gfar_clean_tx_ring().
This would cause an error when building this module. Note, this module
does not build on x86 and was not tested because of that.
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
On RT the trans_pcie->irq_lock lock is converted into a sleeping lock
and can't be used in primary irq handler. The lock is used in mutliple
places which means turning it into a raw lock could increase the
latency of the system.
For now both handlers are moved into the thread.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Clark Williams <clark.williams@gmail.com>
|
|
What I observe is that the TX queue is not empty and does not make any
progress. gfar_clean_tx_ring() does not clean up the packet because it
is not completed yet.
The root cause is that the DMA engine did not start yet (it was
preempted before doing so) and that dumb loop, loops until that packet
is gone.
This is broken since c233cf4 ("gianfar: Fix tx napi polling").
What remains are spurious interrupts if CPU0 cleans up TX packages and
CPU1 returns with IRQ_NONE.
Cc: stable-rt@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
each per-queue lock is taken with spin_lock_irqsave() except in the case
where all of them are taken for some kind of serialisation. As an
optimisation local_irq_save() is used so that lock_tx_qs() and
lock_rx_qs() can use just the spin_lock() variant instead.
On RT local_irq_save() behaves differently so we use the nort()
variant.
Lockdep screems easily by "ethtool -K eth0 rx off tx off"
What remains is missing lockdep annotation that makes lockdep think
lock_tx_qs() may cause a dead lock.
Cc: stable-rt@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
The adjust_link() disables interrupts before taking the queue
locks. On RT those locks are converted to "sleeping" locks and
therefor the local_irq_save/restore must be converted to
local_irq_save/restore_nort.
Reported-by: Xianghua Xiao <xiaoxianghua@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Xianghua Xiao <xiaoxianghua@gmail.com>
|
|
Argh, cut and paste wasn't enough...
Use this patch instead. It needs an irq disable. But, believe it or not,
on SMP this is actually better. If the irq is shared (as it is in Mark's
case), we don't stop the irq of other devices from being handled on
another CPU (unfortunately for Mark, he pinned all interrupts to one CPU).
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
drivers/net/ethernet/3com/3c59x.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Preempt-RT runs into a live lock issue with the NETDEV_TX_LOCKED micro
optimization. The reason is that the softirq thread is rescheduling
itself on that return value. Depending on priorities it starts to
monoplize the CPU and livelock on UP systems.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Disable stuff which is known to have issues on RT
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use disable_irq_nosync() instead of disable_irq() as this might be
called in atomic context with netpoll.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Otherwise the device is not completely shut down.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
|
|
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
On RT the trans_pcie->irq_lock lock is converted into a sleeping lock
and can't be used in primary irq handler. The lock is used in mutliple
places which means turning it into a raw lock could increase the
latency of the system.
For now both handlers are moved into the thread.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Clark Williams <clark.williams@gmail.com>
|
|
What I observe is that the TX queue is not empty and does not make any
progress. gfar_clean_tx_ring() does not clean up the packet because it
is not completed yet.
The root cause is that the DMA engine did not start yet (it was
preempted before doing so) and that dumb loop, loops until that packet
is gone.
This is broken since c233cf4 ("gianfar: Fix tx napi polling").
What remains are spurious interrupts if CPU0 cleans up TX packages and
CPU1 returns with IRQ_NONE.
Cc: stable-rt@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
each per-queue lock is taken with spin_lock_irqsave() except in the case
where all of them are taken for some kind of serialisation. As an
optimisation local_irq_save() is used so that lock_tx_qs() and
lock_rx_qs() can use just the spin_lock() variant instead.
On RT local_irq_save() behaves differently so we use the nort()
variant.
Lockdep screems easily by "ethtool -K eth0 rx off tx off"
What remains is missing lockdep annotation that makes lockdep think
lock_tx_qs() may cause a dead lock.
Cc: stable-rt@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
|
|
The adjust_link() disables interrupts before taking the queue
locks. On RT those locks are converted to "sleeping" locks and
therefor the local_irq_save/restore must be converted to
local_irq_save/restore_nort.
Reported-by: Xianghua Xiao <xiaoxianghua@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Xianghua Xiao <xiaoxianghua@gmail.com>
|
|
Argh, cut and paste wasn't enough...
Use this patch instead. It needs an irq disable. But, believe it or not,
on SMP this is actually better. If the irq is shared (as it is in Mark's
case), we don't stop the irq of other devices from being handled on
another CPU (unfortunately for Mark, he pinned all interrupts to one CPU).
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
drivers/net/ethernet/3com/3c59x.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Preempt-RT runs into a live lock issue with the NETDEV_TX_LOCKED micro
optimization. The reason is that the softirq thread is rescheduling
itself on that return value. Depending on priorities it starts to
monoplize the CPU and livelock on UP systems.
Remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Disable stuff which is known to have issues on RT
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Use disable_irq_nosync() instead of disable_irq() as this might be
called in atomic context with netpoll.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Otherwise the device is not completely shut down.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
commit d96e43e8fce28cf97df576a07af9d65657a41a6f upstream.
This patch adds the missing netif_napi_del() to the flexcan_remove() function.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit f003698e23f6f56a791774f14d0ac35d04872490 upstream.
This patch moves the transceiver enable and disable into seperate functions,
where the NULL pointer check is hidden.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 9b00b300e7bce032c467c36ca47fe2a776887fc2 upstream.
In flexcan_chip_enable() and flexcan_chip_disable() fixed delays are used.
Experiments have shown that the transition from and to low power mode may take
several microseconds.
This patch adds a while loop which polls the Low Power Mode ACK bit (LPM_ACK)
that indicates a successfull mode change. If the function runs into a timeout a
error value is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 7e9e148af01ef388efb6e2490805970be4622792 upstream.
If flexcan_chip_start() in flexcan_open() fails, the interrupt is not freed,
this patch adds the missing cleanup.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 5be93bdda64e85450598c6e97f79fb8f6acf30e0 upstream.
When shutting down the CAN interface (ifconfig canX down) during high CAN bus
loads, the CAN core might hang and freeze the whole CPU.
This patch fixes the shutdown sequence by first disabling the CAN core then
disabling all interrupts.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 0a8d8c446b5429d15ff2d48f46e00d8a08552303 upstream.
Since commit d25f06ea466e "vmxnet3: fix netpoll race condition",
the vmxnet3 driver fails to build when CONFIG_PCI_MSI is disabled,
because it unconditionally references the vmxnet3_msix_rx()
function.
To fix this, use the same #ifdef in the caller that exists around
the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit d25f06ea466ea521b563b76661180b4e44714ae6 upstream.
vmxnet3's netpoll driver is incorrectly coded. It directly calls
vmxnet3_do_poll, which is the driver internal napi poll routine. As the netpoll
controller method doesn't block real napi polls in any way, there is a potential
for race conditions in which the netpoll controller method and the napi poll
method run concurrently. The result is data corruption causing panics such as this
one recently observed:
PID: 1371 TASK: ffff88023762caa0 CPU: 1 COMMAND: "rs:main Q:Reg"
#0 [ffff88023abd5780] machine_kexec at ffffffff81038f3b
#1 [ffff88023abd57e0] crash_kexec at ffffffff810c5d92
#2 [ffff88023abd58b0] oops_end at ffffffff8152b570
#3 [ffff88023abd58e0] die at ffffffff81010e0b
#4 [ffff88023abd5910] do_trap at ffffffff8152add4
#5 [ffff88023abd5970] do_invalid_op at ffffffff8100cf95
#6 [ffff88023abd5a10] invalid_op at ffffffff8100bf9b
[exception RIP: vmxnet3_rq_rx_complete+1968]
RIP: ffffffffa00f1e80 RSP: ffff88023abd5ac8 RFLAGS: 00010086
RAX: 0000000000000000 RBX: ffff88023b5dcee0 RCX: 00000000000000c0
RDX: 0000000000000000 RSI: 00000000000005f2 RDI: ffff88023b5dcee0
RBP: ffff88023abd5b48 R8: 0000000000000000 R9: ffff88023a3b6048
R10: 0000000000000000 R11: 0000000000000002 R12: ffff8802398d4cd8
R13: ffff88023af35140 R14: ffff88023b60c890 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff88023abd5b50] vmxnet3_do_poll at ffffffffa00f204a [vmxnet3]
#8 [ffff88023abd5b80] vmxnet3_netpoll at ffffffffa00f209c [vmxnet3]
#9 [ffff88023abd5ba0] netpoll_poll_dev at ffffffff81472bb7
The fix is to do as other drivers do, and have the poll controller call the top
half interrupt handler, which schedules a napi poll properly to recieve frames
Tested by myself, successfully.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: "David S. Miller" <davem@davemloft.net>
Reviewed-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 469d417b68958a064c09e7875646c97c6e783dfc upstream.
This reverts commit 3804fad45411b48233b48003e33a78f290d227c8.
This commit, together with commit 247bf557273dd775505fb9240d2d152f4f20d304
"xhci 1.0: Limit arbitrarily-aligned scatter gather." were
origially added to get xHCI 1.0 hosts and usb ethernet ax88179_178a devices
working together with scatter gather. xHCI 1.0 hosts pose some requirement on how transfer
buffers are aligned, setting this requirement for 1.0 hosts caused USB 3.0 mass
storage devices to fail more frequently.
USB 3.0 mass storage devices used to work before 3.14-rc1. Theoretically,
the TD fragment rules could have caused an occasional disk glitch.
Now the devices *will* fail, instead of theoretically failing.
>From a user perspective, this looks like a regression; the USB device obviously
fails on 3.14-rc1, and may sometimes silently fail on prior kernels.
The proper soluition is to implement the TD fragment rules for xHCI 1.0 hosts,
but for now, revert this patch until scatter gather can be properly supported.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit d51246481c7f28bbfa1f814ded2da65e531cd4b2 upstream.
While preparing association request, intersection of device's
VHT capability information and corresponding field advertised
by AP is used.
This patch fixes a couple errors while saving and copying vht_cap
and vht_oper fields from AP's beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit c99b1861c232e1f641f13b8645e0febb3712cc71 upstream.
While preparing association request, intersection of device's HT
capability information and corresponding fields advertised by AP
is used.
This patch fixes an error while copying this field from AP's
beacon.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit adb07df1e039e9fe43e66aeea8b4771f83659dbb upstream.
As many Surface Pro I & II users have found out, the mwifiex_usb
doesn't support usb autosuspend, and it has caused some system
stability issues.
Bug 69661 - mwifiex_usb on MS Surface Pro 1 is unstable
Bug 60815 - Interface hangs in mwifiex_usb
Bug 64111 - mwifiex_usb USB8797 crash failed to get signal
information
USB autosuspend get triggered when Surface Pro's AC power is
removed or powertop enables power saving on USB8797 device.
Driver's suspend handler is called here, but resume handler
won't be called until the AC power is put back on or powertop
disables power saving for USB8797.
We need to refactor the suspend/resume handlers to support
usb autosuspend properly. For now let's just remove it.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 1c97560f6d751a620978504a4a888c631192b71a upstream.
We are sending sleep confirm done interrupt in the middle of
sleep handshake. There is a corner case when Tx done interrupt
is received from firmware during sleep handshake due to which
host and firmware power states go out of sync causing cmd and
Tx data timeout problem.
Hence sleep confirm done interrupt is sent at the end of sleep
handshake to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit bb8e6a1ee881d131e404f0f1f5e8dc9281002771 upstream.
We may get a NULL pointer here if skb allocation for Rx packet
was failed earlier.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 4f7ba432202c8330cc03ab959c6228d0de5dc4a3 upstream.
Write io memory to clean PCIe buffer only when PCIe device is
present else this results into crash because of invalid memory
access.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 205e2210daa975d92ace485a65a31ccc4077fe1a upstream.
NICs supported by iwldvm don't handle well TX AMPDU.
Disable it by default, still leave the possibility to
the user to force enable it with a debug parameter.
NICs supported by iwlmvm don't suffer from the same issue,
leave TX AMPDU enabled by default for these.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 143582c6847cb285b361804c613127c25de60ca4 upstream.
Only the first packet is currently handled correctly, but then
all others are assumed to have failed which is problematic. Fix
this, marking them all successful instead (since if they're not
then the firmware will have transmitted them as single frames.)
This fixes the lost packet reporting.
Also do a tiny variable scoping cleanup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[Add the dvm part]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit ec6f678c74dbdb06a6a775bbb00f1d26c17c404b upstream.
We set IWL_STA_UCODE_INPROGRESS flag when we add a station
and clear it when we send the LQ command for it. But the LQ
command is sent only when the association succeeds.
If the association doesn't succeed, we would leave this flag
set and that wouldn't indicate the station entry as vacant.
This probably fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=1065663
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit e7eb65cac0720df8b3946af7f7a9dc363cf0a814 upstream.
Some APs reject STA association request if a listen interval value exceeds
a threshold of 10. Thus, for example, Cisco APs may deny STA associations
returning status code 12 (Association denied due to reason outside the scope
of 802.11 standard) in the association response frame.
Fixing the issue by setting the default IWL_CONN_MAX_LISTEN_INTERVAL value
from 70 to 10.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit b7b146c9c9a0248cc57da71244f672ebc54bbef1 upstream.
Only set sc->rx.discard_next to rx_stats->rs_more when actually
discarding the current descriptor.
Also, fix a detection of broken descriptors:
First the code checks if the current descriptor is not done.
Then it checks if the next descriptor is done.
Add a check that afterwards checks the first descriptor again, because
it might have been completed in the mean time.
This fixes a regression introduced in
commit 723e711356b5a8a95728a890e254e8b0d47b55cf
"ath9k: fix handling of broken descriptors"
Reported-by: Marco André Dinis <marcoandredinis@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 558ff225de80ac95b132d3a115ddadcd64498b4f upstream.
When passing tx frames to the U-APSD queue for powersave poll responses,
the ath_atx_tid pointer needs to be passed to ath_tx_setup_buffer for
proper sequence number accounting.
This fixes high latency and connection stability issues with ath9k
running as AP and a few kinds of mobile phones as client, when PS-Poll
is heavily used
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit 21f8aaee0c62708654988ce092838aa7df4d25d8 upstream.
We check tid->sched without a lock taken on ath_tx_aggr_sleep(). That
is race condition which can result of doing list_del(&tid->list) twice
(second time with poisoned list node) and cause crash like shown below:
[424271.637220] BUG: unable to handle kernel paging request at 00100104
[424271.637328] IP: [<f90fc072>] ath_tx_aggr_sleep+0x62/0xe0 [ath9k]
...
[424271.639953] Call Trace:
[424271.639998] [<f90f6900>] ? ath9k_get_survey+0x110/0x110 [ath9k]
[424271.640083] [<f90f6942>] ath9k_sta_notify+0x42/0x50 [ath9k]
[424271.640177] [<f809cfef>] sta_ps_start+0x8f/0x1c0 [mac80211]
[424271.640258] [<c10f730e>] ? free_compound_page+0x2e/0x40
[424271.640346] [<f809e915>] ieee80211_rx_handlers+0x9d5/0x2340 [mac80211]
[424271.640437] [<c112f048>] ? kmem_cache_free+0x1d8/0x1f0
[424271.640510] [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640578] [<c10fc23c>] ? put_page+0x2c/0x40
[424271.640640] [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640706] [<c1345a84>] ? kfree_skbmem+0x34/0x90
[424271.640787] [<f809dde3>] ? ieee80211_rx_handlers_result+0x73/0x1d0 [mac80211]
[424271.640897] [<f80a07a0>] ieee80211_prepare_and_rx_handle+0x520/0xad0 [mac80211]
[424271.641009] [<f809e22d>] ? ieee80211_rx_handlers+0x2ed/0x2340 [mac80211]
[424271.641104] [<c13846ce>] ? ip_output+0x7e/0xd0
[424271.641182] [<f80a1057>] ieee80211_rx+0x307/0x7c0 [mac80211]
[424271.641266] [<f90fa6ee>] ath_rx_tasklet+0x88e/0xf70 [ath9k]
[424271.641358] [<f80a0f2c>] ? ieee80211_rx+0x1dc/0x7c0 [mac80211]
[424271.641445] [<f90f82db>] ath9k_tasklet+0xcb/0x130 [ath9k]
Bug report:
https://bugzilla.kernel.org/show_bug.cgi?id=70551
Reported-and-tested-by: Max Sydorenko <maxim.stargazer@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
commit b3050248c167871ca52cfdb2ce78aa2460249346 upstream.
The minimum CCA power threshold values have to be adjusted
for existing cards to be in compliance with new regulations.
Newer cards will make use of the values obtained from EEPROM,
support for this was added earlier. To make sure that cards
that are already in use and don't have proper values in EEPROM,
do not violate regulations, use the initvals instead.
Reported-by: Jeang Daniel <dyjeong@qca.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit d7b95315cc7f441418845a165ee56df723941487 ]
Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes
a customer reported issue of randomly dropping packets on the 5719.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 8f355e5cee63c2c0c145d8206c4245d0189f47ff ]
If we receive a PTP event from the NIC when we haven't set up PTP state
in the driver, we attempt to read through a NULL pointer efx->ptp_data,
triggering a panic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 0e7ede80d929ff0f830c44a543daa1acd590c749 ]
We should alloc big buffers also when guest can receive UFO
packets to let the big packets fit into guest rx buffer.
Fixes 5c5167515d80f78f6bb538492c423adcae31ad65
(virtio-net: Allow UFO feature to be set and advertised.)
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 6671b2240c54585d4afb5286a29f1569fe5e40a8 ]
Even though only the outer vlan tag can be HW accelerated in the transmission
path, in the TUN/TAP driver vlan_features mirrors hw_features, which happens
to have the NETIF_F_HW_VLAN_?TAG_TX flags set. Because of this, during packet
tranmisssion through a stacked vlan device dev_hard_start_xmit, (incorrectly)
assuming that the vlan device supports hardware vlan acceleration, does not
add the vlan header to the skb payload and the inner vlan tags are lost
(vlan_tci contains the outer vlan tag when userspace reads the packet from
the tap device).
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|
|
[ Upstream commit 8d0d21f4053c07714802cbe8b1fe26913ec296cc ]
Even if we create a stacked vlan interface such as veth0.10.20, it sends
single tagged frames (tagged with only vid 10).
Because vlan_features of a veth interface has the
NETIF_F_HW_VLAN_[CTAG/STAG]_TX bits, veth0.10 also has that feature, so
dev_hard_start_xmit(veth0.10) doesn't call __vlan_put_tag() and
vlan_dev_hard_start_xmit(veth0.10) overwrites vlan_tci.
This prevents us from using a combination of 802.1ad and 802.1Q
in containers, etc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
|