| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix bug for DM9000 revision B which contain a DSP PHY
DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY,
So need extra change in initialization, For
explicity PHY Reset and PHY init parameter, and
first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe().
Following DM9000_NCR reset cause by dm9000_open() clear the
NCR_MAC_LBK bit.
Without this fix, Power-up FIFO pointers error happen around 2%
rate among Davicom's customers' boards. With this fix, All above
cases can be solved.
Signed-off-by: Joseph CHANG <josright123@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the
'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and
the former field gets assigned from the latter. Make the field match, getting
rid of incorrectly used PHY_DOWN value in assignments/comparisons.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its
mask in EESIPR register. I can 100% reproduce it with the following scenario:
target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device
but doesn't get a proper reply and then succeeds with on-board SMC chip; then
I login and try to bring up the SoC Ether device with 'ifconfig', and I get
an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt
mask in EESIPR register is all 0), if that interrupt is accompanied by a pending
EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx()
because sh_eth_ring_init() hasn't been called yet!
The solution I worked out is the following: in sh_eth_interrupt(), mask the
interrupt status from EESR register with the interrupt mask from EESIPR register
in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit
in this mask set because we always need to fully handle EESR.ECI interrupt in
sh_eth_error() in order to quench it (as it doesn't get cleared by just writing
1 to the this bit as all the other interrupts).
While at it, remove unneeded initializer for 'intr_status' variable and give it
*unsigned long* type, matching the type of sh_eth_read()'s result; fix comment.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Max Filippov <max.filippov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code handling the absent LINK signal (or the absent PSR register -- which
reflects the state of this signal) is quite naive and has probably never really
worked. It's probably enough to say that this code is executed only on the LINK
change interrupt (sic!) but even if we actually have the signal and choose to
ignore it (it might be connected to PHY's link/activity LED output as on the
Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update
'mdp->link' gets executed later than the LINK change interrupt where it is
checked, and so RX/TX never get enabled via ECMR register.
So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen
not to be used) or PSR register is absent, and enable/disable RX/TX directly in
sh_eth_adjust_link() in this case.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure we use proper API to fetch dev->rx_handler_data,
instead of ugly casts.
Rename macvlan_port_get() to macvlan_port_get_rtnl() to document fact
that we hold RTNL when needed, with lockdep support.
This removes sparse warnings as well (CONFIG_SPARSE_RCU_POINTER=y)
CHECK drivers/net/macvlan.c
drivers/net/macvlan.c:706:37: warning: cast removes address space of expression
drivers/net/macvlan.c:775:16: warning: cast removes address space of expression
drivers/net/macvlan.c:924:16: warning: cast removes address space of expression
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
return -ENOMEM instead if kzalloc of cdc_ncm_ctx structure is failed.
and also remove the comparision of ctx structure with NULL and make
it as !ctx.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o VFs might get scheduled out after sending a command to a PF
and scheduled in after receiving a response. Implement a
worker thread to handle atomic commands.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Add support for commands from VF to PF.
o PF validates the commands sent by the VF before sending
it to adapter.
o vPort is a container of resources. PF creates vPort
for VFs and attach resources to it. vPort is
transparent to the VF.
o Separate 83xx TX and RX hardware resource cleanup from 82xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Adapter provides communication channel between VF and PF.
Any control commands from the VF driver are sent to the PF driver
through this communication channel. PF driver validates the
commands before sending them to the adapter. Similarly PF driver
forwards any control command responses to the VF driver
through this communication channel. Adapter sends message pending
event to VF or PF when there is an outstanding response or a command
for VF or PF respectively. When a command or a response is sent over
a channel VF or PF cannot send another command or a response
until adapter sends a channel free event. Adapter allocates 1K area to
VF and PF each for this communication.
o Commands and responses are encapsulated in a header. Header determines
sequence id, number of fragments, fragment number etc.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o VF will use shared MSI-X interrupt vector for Tx and Rx.
o When QLCNIC_INTR_SHARED flag is set Tx and Rx will
share MSI-X interrupt vector. Tx will use a separate
MSI-X interrupt vector from Rx otherwise.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Add PCI device entry for VF.
o Add HW operations for VF.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Add QLCNIC_SRIOV to Kconfig.
o Provide PCI sysfs hooks to enable and disable SR-IOV.
o Allow enabling only when CONFIG_QLCNIC_SRIOV is defined.
o qlcnic_sriov_pf.c has all the PF related SR-IOV
functionality.
o qlcnic_sriov_common.c has VF functionality and SR-IOV
functionality which is common between VF and PF.
o qlcnic_sriov.h is a common header file for SR-IOV defines.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the Datasheet (page 52):
15-12 Reserved
11-0 RXBC Receive Byte Count
This field indicates the present received frame byte size.
The code has a bug:
rxh = ks8851_rdreg32(ks, KS_RXFHSR);
rxstat = rxh & 0xffff;
rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied
Signed-off-by: Max Nekludov <Max.Nekludov@us.elster.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CONFIG_ARCH_IXDP2X01 and CONFIG_MACH_IXDP2351 Kconfig macros are
unused since the ixp23xx and ixp2000 platforms were removed in v3.5. So
remove the last code still depending on these macros. And since
CS89x0_NONISA_IRQ was only set if either of these two macros was defined
we can also remove that macro and the code depending on it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Usage of pci-msi results in corrupted dma packet transfers to the host.
Reported-by: rebelyouth <rebelyouth.hacklab@gmail.com>
Cc: Huang, Xiong <xiong@qca.qualcomm.com>
Tested-by: Christian Sünkenberg <christian.suenkenberg@student.kit.edu>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d0418bb7123f44b23d69ac349eec7daf9103472f (net: sh_eth: Add eth support
for R8A7779 device) was a failed attempt to add support for one of members of
the R-Car SoC family. That's for three reasons: it treated R8A7779 the same
as SH7724 except including quite dirty hack adding ECMR_ELB bit to the mask
in sh_eth_set_rate() while not removing ECMR_RTM bit (despite it's reserved in
R-Car Ether), and it didn't add a new register offset array despite the closest
SH_ETH_REG_FAST_SH4 mapping differs by 0x200 to the offsets all the R-Car Ether
registers have, and also some of the registers in this old mapping don't exist
on R-Car Ether (due to this, SH7724's 'sh_eth_my_cpu_data' structure is not
adequeate for R-Car too). Fix all these shortcomings, restoring the SH7724
related section to its pristine state...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver's header file contains initialized register offset tables which (as
any data definitions), of course, have no business being there. Move them to
the driver's body, somewhat beautifying the initializers, while at it...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WOL is broken because the magic packet status bit is getting set rather
than the enable bit. The PMT interrupt is not getting serviced because
the PMT interrupt is also enabled on the global interrupt, but not
cleared by the global interrupt and the global interrupt is higher
priority. This fixes both of these issues to get WOL working.
There's still a problem with receive after resume, but at least now we
can wake-up.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If skb allocation for the rx ring fails repeatedly, we can reach a point
were the ring is empty. In this condition, the driver is out of sync with
the h/w. While this has always been possible, the removal of the skb
recycling seems to have made triggering this problem easier.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables RX of jumbo frames for LAN7500.
Previously the driver would transmit jumbo frames succesfully but
would drop received jumbo frames (incrementing the interface errors
count).
With this patch applied the device can succesfully receive jumbo
frames up to MTU 9000 (9014 bytes on the wire including ethernet
header).
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.
Fix: We should increase the value to 8192/8
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.
Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The Receive Overflow interrupt is handled correctly
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use clk_prepare_enable/clk_disable_unprepare to be safe on SMP systems.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The core has a bit for swapping packet data endianism.
Reset default from Cadence is off. Xilinx however, who uses this core on the
Zynq SoCs, opted for on.
Force it to off. This shouldn't change the behaviour for current users of the
macb, but enables usage on Zynq devices.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least in the cadence IP core on the Xilinx Zynq SoC the TCOMP/RCOMP flags
are not auto-cleaned. As these flags are evaluated, they need to be cleaned.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next
Jeff Kirsher says:
====================
This series contains updates to e1000e, ixgbe and ixgbevf.
Majority of the changes are against e1000e (from Bruce Allan).
Bruce adds additional error handling on PHY register access, as
well as improve slow performance on 82579 when connected to a
10Mbit hub. In addition, fixes LED blink logic for cathode
LED design. Most notable is added EEE support which is enabled
by default and the added support for LTR on I217/I218.
The ixgbe and ixgbevf from Greg Rose changes the VM so that if a user
does not assign a MAC address, the MAC address is set to all zeros
instead of a random MAC address. This ensures that we always know when
we have a random address and udev won't get upset about it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the administrator has not assigned a MAC address to the VF via the
PF then handle it gracefully by generating a temporary MAC address.
This ensures that we always know when we have a random address and
udev won't get upset about it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The previous commit ce43a2168c59bc47b5f0c1825fd5f9a2a9e3b447 (e1000e:
cleanup USLEEP_RANGE checkpatch checks) converted a number of delays and
sleeps as recommended in ./Documentation/timers/timers-howto.txt.
Unfortunately, a few of the udelay() to usleep_range() conversions are in
code paths that are in an atomic context in which usleep_range() should
not be used. Revert those specific changes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Set the Latency Tolerance Reporting (LTR) values for the "PCIe-like"
GbE MAC in the Lynx Point PCH based on Rx buffer size and link speed
when link is up (which must not exceed the maximum latency supported
by the platform), otherwise specify there is no LTR requirement.
Unlike true-PCIe devices which set the LTR maximum snoop/no-snoop
latencies in the LTR Extended Capability Structure in the PCIe Extended
Capability register set, on this device LTR is set by writing the
equivalent snoop/no-snoop latencies in the LTRV register in the MAC and
set the SEND bit to send an Intel On-chip System Fabric sideband (IOSF-SB)
message to the PMC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Now that IEEE802.3az-2010 Energy Efficient Ethernet has been approved as
standard (September 2010) and the driver can enable and disable it via
ethtool, enable the feature by default on parts which support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Devices supported by the driver which support EEE (currently 82579, I217
and I218) are advertising EEE capabilities during auto-negotiation even
when EEE has been disabled. In addition to not acting as expected, this
also caused the EEE status reported by 'ethtool --show-eee' to be wrong
when two of these devices are connected back-to-back and EEE is disabled
on one. In addition to fixing this issue, the ability for the user to
specify which speeds (100 or 1000 full-duplex) to advertise EEE support
has been added.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the MAC and PHY are in two different modes (different power levels
and interconnect speeds), it could take a long time before a PHY register
access timed out using the existing MAC-PHY interconnect configuration
coded into the driver for ICH- and PCH-based LOMs. Introduce an I217/I218-
specific .setup_physical_interface operation which does not override the
interconnect configuration in the NVM.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the LEDs are driven by cathode, the bit logic is reversed. Use the
LED Invert bit to invert the logic. Cleanup use of a magic number and
change the for loop increment to reduce the number of shifts.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Two 82579 LOMs connected via a 10Mb hub experience extraordinarily low
performance. This is because 82579 is excessively aggressive on transmit
at 10Mb half-duplex and will not provide sufficient time for the link
partner to transmit. When the link partner is also 82579, the result is a
lot of collisions (and corresponding re-transmits) that cause the poor
performance. To work-around this issue, significantly increase the IPG in
the MAC to allow enough gap for the link partner to transmit and reduce the
Rx latency in the analog PHY to 0 to reduce the number of collisions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
PHY reads/writes via the MDIC register could potentially return results
from a previous PHY register access. If that happens, the offset in the
returned results will be that of the previous access and if that is
different from the expected offset, log a debug message and error out.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move mutex initialization by allocation of the mailbox it protects.
introduced in commit 1d6f3cd89 'bnx2x: Prevent VF race'
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
yam_open has a redundant null check on null, it will
never be called with dev == NULL. Remove this redundant check.
This also cleans up a smatch warning:
drivers/net/hamradio/yam.c:869 yam_open() warn: variable
dereferenced before check 'dev' (see line 867)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
here's a patch series for net for the v3.9 release cycle. Fengguang Wu found
two problems with the sja1000 drivers:
A macro in the SH architecture collides with one in the sja1000 driver. I
created a minimal patch suited for stable, only changing this particular
define. (Once net is merged back to net-next, I'll post a patch to uniformly
use a SJA1000_ prefix for the sja100 private defines.) If you prefer, I can
squash both patches together.
Fengguang further noticed that the peak pcmcia driver will not compile on archs
without ioport support. I created a patch to limit the driver to archs which
select HAS_IOPORT in Kconfig.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
This series contains updates to e1000, ixgb and e1000e for Christoph.
Christoph provides 3 patches to resolve missing dma_error_call's to
provided Intel drivers which did not have this fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 184b89044fb6e2a74611dafa69b1dce0d98612c6 ("tg3: Use VPD fw version
when present") introduced VPD parsing that contained a potential length
overflow.
Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.
http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Oded Horovitz <oded@privatecore.com>
Reported-by: Brad Spengler <spender@grsecurity.net>
Cc: stable@vger.kernel.org
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
restarting tx queue
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.
Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
