| Age | Commit message (Collapse) | Author |
|---|
|
Permanent MAC is wrongly supplied in create iface command. Call the
command with no MAC address and then MAC address should be later queried
and applied.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
instead of raw assignment to current->state
Signed-off-by: Hong Zhiguo <honkiko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends the bnx2x's ethtool interface to enable
control in the eee feature, as well as report statistic information
about it.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds energy efficient energy support (802.3az) to bnx2x
boards with 84833 phys (and sufficiently new BC and external FW).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Use correct l3 (ETH_IP or ETH_IPV6)protcol in case
of inband vlan. Because of incorrect protcol type driver
was setting incorrect opcode. This resulted in adapter calculating
checksum incorrectly.
o Updated driver version to 5.0.29
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add debug messages for FW CDRP command failure.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Linux stack estimates MSS from skb->len or skb_shinfo(skb)->gso_size.
In case of LRO skb->len is aggregate of len of number of packets hence MSS
obtained using skb->len would be incorrect. Incorrect estimation of recv MSS
would lead to delayed acks in some traffic patterns (which sends two or three
packets and wait for ack and only then send remaining packets). This leads to
drop in performance. Hence we need to set gso_size to MSS obtained from firmware.
o This is fixed recently in firmware hence the MSS is obtained based on
capability. If fw is capable of sending the MSS then only driver sets the gso_size.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We added another error condition here, but if we were to hit it then
we need to unregister_netdev() before doing the free_netdev().
Otherwise we would hit the BUG_ON() in free_netdev():
BUG_ON(dev->reg_state != NETREG_UNREGISTERED);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the support for D_CAN controller driver to the existing
C_CAN driver.
Bosch D_CAN controller is a full-CAN implementation which is compliant
to CAN protocol version 2.0 part A and B. Bosch D_CAN user manual can be
obtained from: http://www.semiconductors.bosch.de/media/en/pdf/
ipmodules_1/can/d_can_users_manual_111.pdf
A new array is added for accessing the d_can registers, according to d_can
controller register space.
Current D_CAN implementation has following limitations, this is done
to avoid large changes to the C_CAN driver.
1. Message objects are limited to 32, 16 for RX and 16 for TX. C_CAN IP
supports upto 32 message objects but in case of D_CAN we can configure
upto 128 message objects.
2. Using two 16bit reads/writes for accessing the 32bit D_CAN registers.
3. These patches have been tested on little endian machine, there might
be some hidden endian-related issues due to the nature of the accesses
(32-bit registers accessed as 2 16-bit registers). However, I do not
have a big-endian D_CAN implementation to confirm.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
c_can uses overlay structure for accessing c_can module registers.
With this kind of implementation it is difficult to add one more ip
which is similar to c_can in functionality but different register
offsets.
This patch changes the overlay structure implementation to an array
with register offset as index. This way we can overcome the above
limitation.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
Adding device IDs for Aircard 320U and two other devices
found in the out-of-tree version of this driver.
Cc: linux@sierrawireless.com
Cc: Autif Khan <autif.mlist@gmail.com>
Cc: Tom Cassidy <tomas.cassidy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 452503ebc (ARM: Orion: Eth: Add clk/clkdev support.) broke
the building of the driver on architectures which don't have clk
support. In particular PPC32 Pegasos which uses this driver.
Add #ifdef around the clk API usage.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes the driver when built as dynamic module.
In fact, the platform part cannot be built and the probe fails
(thanks to Bob Liu that reported this bug).
v2: as D. Miller suggested, it is not necessary to make the
pci and the platform code mutually exclusive.
Having both could also help, at built time ,to verify that
all the code is validated and compiles fine.
v3: removed wrong Reviewed-by from the patch
Reported-by: Bob Liu <lliubbo@gmail.com>
cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Neatened the mwifiex_deauthenticate_infra function which
was doing odd things with array pointers and not using
is_zero_ether_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.
Change the argument to a non-const pointer.
A function in stmmac needed a __force to avoid a sparse
warning. Added it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CUST_SCRATCHPAD_CSR register is used for marking if FW cleanup is
needed. This is used in a crash kernel scenario. Do no use this register as
it is not available for some functions. Instead, always issue an FLR when
a function is probed *except* when VFs are preset (enabled in the previous
PF load).
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting the PCI MRRS to a value of 4096 (overriding the system decided
value) had provided perf improvement in TX.
But, IBM has provided feedback that on POWER platforms, this value is set
by the system firmware, and drivers modifying this value can cause
unpredictable results (like EEH errors.) So, backing off this change.
On POWER7 platforms most slots, it seems, do get a MRRS of 4096.
This patch reverts the following commit:
"be2net: Modified PCI MaxReadReq size to 4096 bytes"
commit 5a56eb10babbcd7b3796dc3c28c271260aa3608d.
Suggested-by: Brian King <bjking1@us.ibm.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- get rid of 2 unused arguments to the routine and some unused code
- don't use the term "vlan_tag" in place of "vid" as they are different
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
be_vid_config() is called from be_setup() to replay config cmds after
a card reset. Skip calling it when no vlans are configured.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hardware bit IXGBE_RXD_STAT_VP appears to be set even when Rx
stripping is disabled. This results in passing frames up the stack
which do not have the 802.1Q tag stripped but have the tci bits
set as if it was.
Working around this with a check for the feature flag bit. I
would welcome any better ideas or a pointer to exactly which
bits in the hardware register need to be cleared to get the
IXGBE_RXD_STAT_VP bit to be set per data sheet.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
DCB can be used independent of if RX VLAN stripping is enabled
or disabled so remove erroneous check.
Also enable or disable VLAN stripping when features are applied so
hardware and feature flags are in sync.
CC: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
commit 44abd5c12767a8c567dc4e45fd9aec3b13ca85e0 introduced NULL pointer
dereferences when attempting to access the check_reset_block function
pointer on 8257x and 80003es2lan non-copper devices.
This fix should be applied back through 3.4.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise the LEDs stick around and cause issues the
next time around since they're still there but not
really hooked up.
Cc: stable@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Linus reported that due to mac80211 failing to register
the device (due to WoWLAN) his machine crashed etc. as
we double-freed the vmalloc() firmware area. His patch
to fix it was very similar to this one but I noticed
that there's another bug in the area: we complete the
completion before starting, so since we're running in
a work struct context stop() could be called while in
the middle of start() which will almost certainly lead
to issues.
Make a modification similar to his to avoid the double-
free but also move the completion to another spot so it
is only done after start() either finished or failed so
that stop() can have a consistent state.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If CONFIG_PM_SLEEP is disabled, then iwlwifi doesn't
support suspend/resume handlers and thus mac80211
(correctly) refuses advertising WoWLAN. Disable
WoWLAN in the driver in this case.
Cc: stable@kernel.org
Reported-by: Sebastian Kemper <sebastian_ml@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Remove spinlock as atomic_t can be used instead. Note we use only 16
lower bits, upper bits are changed but we impilcilty cast to u16.
This fix possible deadlock on IBSS mode reproted by lockdep:
=================================
[ INFO: inconsistent lock state ]
3.4.0-wl+ #4 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/u:2/30374 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&intf->seqlock)->rlock){+.?...}, at: [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
{IN-SOFTIRQ-W} state was registered at:
[<c04978ab>] __lock_acquire+0x47b/0x1050
[<c0498504>] lock_acquire+0x84/0xf0
[<c0835733>] _raw_spin_lock+0x33/0x40
[<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f9979f2a>] rt2x00queue_write_tx_frame+0x1a/0x300 [rt2x00lib]
[<f997834f>] rt2x00mac_tx+0x7f/0x380 [rt2x00lib]
[<f98fe363>] __ieee80211_tx+0x1b3/0x300 [mac80211]
[<f98ffdf5>] ieee80211_tx+0x105/0x130 [mac80211]
[<f99000dd>] ieee80211_xmit+0xad/0x100 [mac80211]
[<f9900519>] ieee80211_subif_start_xmit+0x2d9/0x930 [mac80211]
[<c0782e87>] dev_hard_start_xmit+0x307/0x660
[<c079bb71>] sch_direct_xmit+0xa1/0x1e0
[<c0784bb3>] dev_queue_xmit+0x183/0x730
[<c078c27a>] neigh_resolve_output+0xfa/0x1e0
[<c07b436a>] ip_finish_output+0x24a/0x460
[<c07b4897>] ip_output+0xb7/0x100
[<c07b2d60>] ip_local_out+0x20/0x60
[<c07e01ff>] igmpv3_sendpack+0x4f/0x60
[<c07e108f>] igmp_ifc_timer_expire+0x29f/0x330
[<c04520fc>] run_timer_softirq+0x15c/0x2f0
[<c0449e3e>] __do_softirq+0xae/0x1e0
irq event stamp: 18380437
hardirqs last enabled at (18380437): [<c0526027>] __slab_alloc.clone.3+0x67/0x5f0
hardirqs last disabled at (18380436): [<c0525ff3>] __slab_alloc.clone.3+0x33/0x5f0
softirqs last enabled at (18377616): [<c0449eb3>] __do_softirq+0x123/0x1e0
softirqs last disabled at (18377611): [<c041278d>] do_softirq+0x9d/0xe0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&intf->seqlock)->rlock);
<Interrupt>
lock(&(&intf->seqlock)->rlock);
*** DEADLOCK ***
4 locks held by kworker/u:2/30374:
#0: (wiphy_name(local->hw.wiphy)){++++.+}, at: [<c045cf99>] process_one_work+0x109/0x3f0
#1: ((&sdata->work)){+.+.+.}, at: [<c045cf99>] process_one_work+0x109/0x3f0
#2: (&ifibss->mtx){+.+.+.}, at: [<f98f005b>] ieee80211_ibss_work+0x1b/0x470 [mac80211]
#3: (&intf->beacon_skb_mutex){+.+...}, at: [<f997a644>] rt2x00queue_update_beacon+0x24/0x50 [rt2x00lib]
stack backtrace:
Pid: 30374, comm: kworker/u:2 Not tainted 3.4.0-wl+ #4
Call Trace:
[<c04962a6>] print_usage_bug+0x1f6/0x220
[<c0496a12>] mark_lock+0x2c2/0x300
[<c0495ff0>] ? check_usage_forwards+0xc0/0xc0
[<c04978ec>] __lock_acquire+0x4bc/0x1050
[<c0527890>] ? __kmalloc_track_caller+0x1c0/0x1d0
[<c0777fb6>] ? copy_skb_header+0x26/0x90
[<c0498504>] lock_acquire+0x84/0xf0
[<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<c0835733>] _raw_spin_lock+0x33/0x40
[<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib]
[<f997a5cf>] rt2x00queue_update_beacon_locked+0x5f/0xb0 [rt2x00lib]
[<f997a64d>] rt2x00queue_update_beacon+0x2d/0x50 [rt2x00lib]
[<f9977e3a>] rt2x00mac_bss_info_changed+0x1ca/0x200 [rt2x00lib]
[<f9977c70>] ? rt2x00mac_remove_interface+0x70/0x70 [rt2x00lib]
[<f98e4dd0>] ieee80211_bss_info_change_notify+0xe0/0x1d0 [mac80211]
[<f98ef7b8>] __ieee80211_sta_join_ibss+0x3b8/0x610 [mac80211]
[<c0496ab4>] ? mark_held_locks+0x64/0xc0
[<c0440012>] ? virt_efi_query_capsule_caps+0x12/0x50
[<f98efb09>] ieee80211_sta_join_ibss+0xf9/0x140 [mac80211]
[<f98f0456>] ieee80211_ibss_work+0x416/0x470 [mac80211]
[<c0496d8b>] ? trace_hardirqs_on+0xb/0x10
[<c077683b>] ? skb_dequeue+0x4b/0x70
[<f98f207f>] ieee80211_iface_work+0x13f/0x230 [mac80211]
[<c045cf99>] ? process_one_work+0x109/0x3f0
[<c045d015>] process_one_work+0x185/0x3f0
[<c045cf99>] ? process_one_work+0x109/0x3f0
[<f98f1f40>] ? ieee80211_teardown_sdata+0xa0/0xa0 [mac80211]
[<c045ed86>] worker_thread+0x116/0x270
[<c045ec70>] ? manage_workers+0x1e0/0x1e0
[<c0462f64>] kthread+0x84/0x90
[<c0462ee0>] ? __init_kthread_worker+0x60/0x60
[<c083d382>] kernel_thread_helper+0x6/0x10
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Enforcing interface combinations broke uses of hwsim
with multiple virtual interfaces. Advertise that all
combinations are possible to fix this.
Reported-by: Nirav Shah <nirav.j2.shah@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since my commit
iwlwifi: use valid TX/RX antenna from hw_params
the config values are pure overrides, not the
real values for all hardware. Therefore, the
EEPROM TX power reading code checks the wrong
values, it should check the hw_params values.
Cc: stable@kernel.org [3.4]
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden
SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Mark bss_config parameters as invalid before setting AP channel.
This prevents from setting invalid parameters while setting AP
channel to FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch removes two useless initialisations in the
stmmac_rx and stmmac_tx functions.
In the former, the count variable was reset twice and in
the stmmac_tx we only need to increment the dirty pointer
w/o setting the entry variable.
v2: review the subject and comment that was not clear in my
first version.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the busy-waiting/udelay to wait_event on outstanding sends.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the interrupt mask for IC101 A/G devices
and now enables the link/speed/duplex interrupts.
This is done by setting the "INTR pin used" bit and cleaning
all the other bits in the Register 17.
Reported-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Raffaele Recalcati <raffaele.recalcati@bticino.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using | with a constant is always true.
Likely this should have be &.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix the issue of C_CAN interrupts getting disabled forever when canconfig
utility is used multiple times. According to NAPI usage we disable all
the hardware interrupts in ISR and re-enable them in poll(). Current
implementation calls napi_enable() after hardware interrupts are enabled.
If we get any interrupts between these two steps then we do not process
those interrupts because napi is not enabled. Mostly these interrupts
come because of STATUS is not 0x7 or ERROR interrupts. If napi_enable()
happens before HW interrupts enabled then c_can_poll() function will be
called eventual re-enabling.
This patch moves the napi_enable() call before interrupts enabled.
Cc: stable@kernel.org # 2.6.39+
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
